Examples, Terminology and Formula Index
Worked Examples by Topic
Bolted Connections
- Two M20 bolts connecting an angle: link the checks (Bolted Angle) · 2022-09-19
- 750 kN double-cover splice: separate capacity and spacing (Double-cover Splice) · 2022-09-19 (also in: 2022-11-07)
- Q3: combine shear at each bolt in an eccentric in-plane group (In-plane Eccentric Bolts) · 2022-09-26
- Q4: bracket-bolt shear, tension and interaction (Shear–Tension Interaction) · 2022-09-26
- 960 kN test question: four checks (Four Checks) · 2022-11-07
- M27 plate bearing: calculate all four bounds (Four Bearing Limits) · 2022-11-14
Welded Connections
- 850 kN lap weld: effective and provided lengths (Lap Weld) · 2022-10-03 (also in: 2022-11-14)
- Single welded angle: check the member, then allocate welds (Welded Angle) · 2022-10-03
- 65×50×8 angle: centroid and unequal weld lengths (Unequal Weld Lengths) · 2022-09-26
- 350 kN double angles: total areas and side distribution (Double Angles) · 2022-10-03
- Eccentric weld Q6: from geometry to resultant (Eccentric Weld Group) · 2022-10-03
- Q7: separate flange and web weld roles (Bracket Flange and Web Welds) · 2022-10-03
Beams
- B1 floor beam: from slab load to strength and deflection (Complete Beam Walkthrough) · 2022-10-03 (also in: 2022-10-17)
- B2: the internal beam in the same floor (Interior Beam) · 2022-10-17
- B3: a support reaction loads the next beam (Reaction Transfer) · 2022-10-17
- B3 support: local web bearing and buckling (B3 Local Web Checks) · 2022-10-17
- Initial section selection from load demand (Trial Section Selection) · 2022-10-17
- Local web checks: both modes must pass (Web Bearing and Buckling) · 2022-10-17
- 6 m revision beam: coexisting shear and deflection (Coexistent Shear) · 2022-11-14
- 8 m revision beam: resistance and deformation again (Beam Check Practice) · 2022-11-14
Lateral-torsional Buckling
- Unrestrained B2: a strong section can still buckle (Unrestrained Beam) · 2022-10-24
- B3 with midspan restraint: complete the LTB procedure (Restrained Segments) · 2022-10-24
- Overhanging beam Q5: separate load patterns and check AB (Overhanging Beam) · 2022-10-24
Columns
- Pure-compression UC column: from two-axis lookup to capacity (Axial Compression) · 2022-10-24
- Example 5: biaxial checks for a non-sway-frame column (Biaxial Column) · 2022-10-31
- Column Q2: section and member checks for 305×305×118 UC (Column Q2) · 2022-10-31
- Column Q3: biaxial bending of 305×305×198 UC (Column Q3) · 2022-10-31
- Q5: utilisation slightly above 1, judged marginally OK by the lecturer (Marginal Utilization) · 2022-10-31
- Simple-construction column: how beam reactions produce moments (Beam Reactions into Columns) · 2022-10-24
- Column interaction revision: where each ratio comes from (Column Interaction Review) · 2022-11-14
Terminology
| Chinese | English | Definition | Learn More |
|---|---|---|---|
| 塑性截面模數 | Plastic Section Modulus | : section modulus for fully plastic bending. | Read an I-section and its section table (Section Properties) |
| 彈性截面模數 | Elastic Section Modulus | : section modulus at first yield of the extreme fibre. | Read an I-section and its section table (Section Properties) |
| 非側移框架 | Non-sway Frame | A frame with no appreciable lateral sway under lateral loading; column effective lengths are shorter under the corresponding conditions. | Instability can precede material crushing (Buckling) |
| 側扭屈曲 | Lateral-torsional Buckling, LTB | Overall instability involving lateral movement of the compression flange and twisting of the section. | Why a beam moves sideways and twists (Lateral-torsional Buckling) |
| 有效長度 | Effective Length | Equivalent length used for buckling, accounting for end restraint. | Instability can precede material crushing (Buckling) |
| 支座反力 | Support Reaction | Force exerted by a support to prevent member movement. | Why an object can remain stationary (Forces and Equilibrium) |
| 荷載路徑 | Load Path | The route by which load travels from slab through beams and columns to the ground. | How loads travel from the slab to the ground (Load Path) |
| 分擔寬度 | Tributary Width | Width of slab whose load is carried by one beam. | How loads travel from the slab to the ground (Load Path) |
| 截面分類 | Section Classification | Classification into Classes 1–4 using width-to-thickness ratios, determining the available bending expression. | Will the plate buckle before its material strength is fully mobilised? (Section Classification) |
| 局部屈曲 | Local Buckling | Local instability of a thin plate under compression. | Will the plate buckle before its material strength is fully mobilised? (Section Classification) |
| 截面模數 | Section Modulus | Section property or relating stress to bending resistance. | Read an I-section and its section table (Section Properties) |
| 迴轉半徑 | Radius of Gyration | , used to calculate slenderness. | Read an I-section and its section table (Section Properties) |
| 有效面積 | Effective Area | Net area multiplied by , capped at gross area. | How holes weaken a steel plate (Net and Effective Area) |
| 有效喉厚 | Effective Throat | Effective load-carrying thickness of a fillet weld, approximately 0.7 times its leg size. | Leg size, throat and effective length (Fillet Weld Geometry) |
| 有效焊長 | Effective Weld Length | Weld length counted for resistance after end deductions. | Leg size, throat and effective length (Fillet Weld Geometry) |
| 彎矩放大 | Moment Amplification | Multiplication of moment by an amplification factor to account for second-order effects. | Combined axial force and bending (Interaction Checks) |
| 均佈荷載 | Uniformly Distributed Load, UDL | Load distributed uniformly along a length, in kN/m. | Turn the physical structure into a calculation model (Free-body Diagram) |
| 彈性模數 | Elastic Modulus | ; the course uses 205000 N/mm². | Material strength and member capacity (Stress and Resistance) |
| 彎曲剛度 | Flexural Rigidity | ; a larger value means greater resistance to bending deformation. | Excessive bending deformation versus insufficient resistance (Deflection) |
| 剪切面積 | Shear Area | : area used for shear resistance; for the rolled I-section in this course. | Read an I-section and its section table (Section Properties) |
| 極二次矩 | Polar Second Moment | : geometric property used in weld-group torsion analysis. | Leg size, throat and effective length (Fillet Weld Geometry) |
| 屈曲曲線 | Buckling Curve | The curve selected by section type and buckling axis, from curves a–. | Instability can precede material crushing (Buckling) |
| 塊狀剪切 | Block Shear | Detachment of a plate block around a bolt group along combined shear and tension paths. | How holes weaken a steel plate (Net and Effective Area) |
| 永久荷載 | Dead Load, DL | DL: permanent loading such as structural self-weight and fixed equipment. | When to check strength and when to check deformation (Limit States) |
| 施加荷載 | Imposed Load / Live Load, LL | LL: variable loading from occupancy, furniture and use. | When to check strength and when to check deformation (Limit States) |
| 鋼材等級 | Steel Grade | Steel class set by minimum yield strength, such as S355; it decides which Data File column you read. | Steel grades S275, S355 and S460, and strength classification |
| 未乘係數 | Unfactored | A load at its original value, not yet multiplied by the load factor 1.4 or 1.6. | When to check strength and when to check deformation (Limit States) |
| 已乘係數 | Factored | A load already multiplied by its load factor, used for strength checks. | When to check strength and when to check deformation (Limit States) |
| 荷載係數 | Load Factor | The safety factor applied to a load for strength checks: 1.4 for dead load, 1.6 for imposed load. | When to check strength and when to check deformation (Limit States) |
| 側向約束 | Lateral Restraint | Something that holds the compression flange of a beam and stops it moving sideways. | Why a beam moves sideways and twists (Lateral-torsional Buckling) |
| 細長比 | Slenderness Ratio | Effective length divided by radius of gyration, ; a larger value indicates greater susceptibility to buckling. | Instability can precede material crushing (Buckling) |
| 受力圖 | Free-body Diagram | A drawing of an isolated member with all external forces and reactions. | Turn the physical structure into a calculation model (Free-body Diagram) |
| 線荷載 | Line Load | Load per metre of length, in kN/m. | Use units to identify what you are calculating (Units and Dimensions) |
| 面荷載 | Area Load | Load per square metre, in kN/m². | Use units to identify what you are calculating (Units and Dimensions) |
| 慣性矩 | Second Moment of Area | : geometric property governing resistance to bending deformation, in mm⁴ or cm⁴. | Read an I-section and its section table (Section Properties) |
| 利用率 | Utilization Ratio | Demand divided by resistance; it must not exceed 1 to pass. | Material strength and member capacity (Stress and Resistance) |
| 淨面積 | Net Area | Section area remaining after bolt-hole deductions. | How holes weaken a steel plate (Net and Effective Area) |
| 毛面積 | Gross Area | Section area before deducting holes. | How holes weaken a steel plate (Net and Effective Area) |
| 角焊縫 | Fillet Weld | A weld with a triangular cross-section, commonly used in connections. | Leg size, throat and effective length (Fillet Weld Geometry) |
| 交互式 | Interaction Equation | An expression combining axial and biaxial moment utilisation, with a total no greater than 1. | Combined axial force and bending (Interaction Checks) |
| 偏心距 | Eccentricity | Perpendicular distance from the force's line of action to the reference centre. | Why the position of a force matters (Moment and Eccentricity) |
| 集中力 | Point Load | Force applied at a point, in kN. | Turn the physical structure into a calculation model (Free-body Diagram) |
| 焊腳 | Leg Size | Side dimension of the triangular fillet weld. | Leg size, throat and effective length (Fillet Weld Geometry) |
| 剪力 | Shear Force | Internal force tending to slide the two sides of a cut section relative to each other. | Internal shear force and bending moment in a beam (Shear Force and Bending Moment) |
| 彎矩 | Bending Moment | Internal moment causing member bending, in kNm. | Why the position of a force matters (Moment and Eccentricity) |
| 撓度 | Deflection | Displacement of a loaded member, measured in mm. | Excessive bending deformation versus insufficient resistance (Deflection) |
| 應力 | Stress | Force per unit area, in N/mm². | Material strength and member capacity (Stress and Resistance) |
| 屈服 | Yielding | The onset of substantial plastic deformation as steel reaches yield strength. | Material strength and member capacity (Stress and Resistance) |
| 屈曲 | Buckling | Instability of a compression member that can occur before material crushing. | Instability can precede material crushing (Buckling) |
| 翼緣 | Flange | The top and bottom horizontal plates of an I-section. | Read an I-section and its section table (Section Properties) |
| 腹板 | Web | The vertical plate between the flanges of an I-section. | Read an I-section and its section table (Section Properties) |
| 端距 | End Distance | Distance from hole centre to plate end along the force-transfer direction. | Several failure paths in a bolted connection (Bolted Connections) |
| 孔徑 | Hole Diameter | Diameter of the bolt hole, larger than the bolt diameter. | Several failure paths in a bolted connection (Bolted Connections) |
| 單剪 | Single Shear | A bolt acting across one shear plane. | Several failure paths in a bolted connection (Bolted Connections) |
| 雙剪 | Double Shear | A bolt acting across two shear planes, doubling shear resistance in the stated model. | Several failure paths in a bolted connection (Bolted Connections) |
| 承壓 | Bearing | Contact compression between a bolt and the hole wall. | Several failure paths in a bolted connection (Bolted Connections) |
| 應變 | Strain | Extension or contraction divided by original length. | Material strength and member capacity (Stress and Resistance) |
| 形心 | Centroid | Geometric centre of a section or weld group. | Why the position of a force matters (Moment and Eccentricity) |
| 回焊 | End Return | A short continuation of a weld around an end corner. | Leg size, throat and effective length (Fillet Weld Geometry) |
| 力矩 | Moment | Force times perpendicular distance, measuring a turning effect. | Why the position of a force matters (Moment and Eccentricity) |
| 板件 | Plate Element | One flat piece of a section or connection, such as a flange, a web or a cover plate. | Will the plate buckle before its material strength is fully mobilised? (Section Classification) |
| 裕度 | Margin | How much the capacity exceeds the demand; a small margin means the check is close to its limit. | Material strength and member capacity (Stress and Resistance) |
| 工況 | Load Case | One arrangement of the loads; different arrangements make the forces largest at different places. | When to check strength and when to check deformation (Limit States) |
| 細部 | Detailing | Rules on hole spacing, end distance, minimum weld size and the like, to be met even when the capacities pass. | Several failure paths in a bolted connection (Bolted Connections) |
| 插值 | Interpolation | Taking a value in proportion when yours falls between two rows of a table. | Reading a table and interpolating |
| 需求 | Demand | The force or moment the loads cause in a member. | Material strength and member capacity (Stress and Resistance) |
| 容量 | Capacity | The largest force or moment a member or connection can take. | Material strength and member capacity (Stress and Resistance) |
Foundational Formulas and Conditions
Use units to identify what you are calculating (Units and Dimensions)
See the linked foundation unit for symbols, units and conditions of use.
Reading a table and interpolating
See the linked foundation unit for symbols, units and conditions of use.
Material strength and member capacity (Stress and Resistance)
See the linked foundation unit for symbols, units and conditions of use.
Why an object can remain stationary (Forces and Equilibrium)
See the linked foundation unit for symbols, units and conditions of use.
Why the position of a force matters (Moment and Eccentricity)
See the linked foundation unit for symbols, units and conditions of use.
How loads travel from the slab to the ground (Load Path)
See the linked foundation unit for symbols, units and conditions of use.
Internal shear force and bending moment in a beam (Shear Force and Bending Moment)
See the linked foundation unit for symbols, units and conditions of use.
Read an I-section and its section table (Section Properties)
See the linked foundation unit for symbols, units and conditions of use.
Steel grades S275, S355 and S460, and strength classification
See the linked foundation unit for symbols, units and conditions of use.
When to check strength and when to check deformation (Limit States)
See the linked foundation unit for symbols, units and conditions of use.
Will the plate buckle before its material strength is fully mobilised? (Section Classification)
See the linked foundation unit for symbols, units and conditions of use.
Excessive bending deformation versus insufficient resistance (Deflection)
See the linked foundation unit for symbols, units and conditions of use.
Several failure paths in a bolted connection (Bolted Connections)
See the linked foundation unit for symbols, units and conditions of use.
How holes weaken a steel plate (Net and Effective Area)
See the linked foundation unit for symbols, units and conditions of use.
Leg size, throat and effective length (Fillet Weld Geometry)
See the linked foundation unit for symbols, units and conditions of use.
Instability can precede material crushing (Buckling)
See the linked foundation unit for symbols, units and conditions of use.
Why a beam moves sideways and twists (Lateral-torsional Buckling)
See the linked foundation unit for symbols, units and conditions of use.
Combined axial force and bending (Interaction Checks)
See the linked foundation unit for symbols, units and conditions of use.
Design Formula Index
These links lead to units containing formulas or worked examples. Tabulated design factors come from the code; they are not derived from basic equilibrium.
- Separate ultimate and serviceability checks (Ultimate and Serviceability Limit States) · 2022-09-19
- Read the section table before classifying (Section Tables and Classification) · 2022-09-19
- Force transfer and bearing in ordinary bolts (Bearing-type Bolts) · 2022-09-19
- First angle-connection example: complete shear first (Angle Connection Example) · 2022-09-19
- The lecturer next checks the 750 kN splice and revises its spacing (Splice Layout Check) · 2022-09-19
- Return to the angle: gross, net and effective areas (Gross, Net and Effective Area) · 2022-09-19
- From the formula sheet back to connection geometry (Connection Geometry) · 2022-09-26
- Two eccentricity models: identify the rotation first (Two Eccentricity Models) · 2022-09-26
- Q3: recalculate the resultant after correcting the load share (Correcting the Load Share) · 2022-09-26
- Q4: check interaction after the individual components (Interaction Check) · 2022-09-26
- Start welding with throat and load-carrying area (Fillet Weld Basics) · 2022-09-26
- Centroid-based distribution, followed by lap welds (Centroid and Weld Length) · 2022-09-26
- 850 kN lap weld: length, minimum size and plates (Lap Weld and Plate Checks) · 2022-10-03
- Bracket welds: assign roles before calculating demand (Bracket Weld Model) · 2022-10-03
- Single and double angles: shared method, different factors (Single and Double Angles) · 2022-10-03
- Q6: calculate the eccentric weld-group resultant (Eccentric Weld Group) · 2022-10-03
- Q7: 600 kN bracket, from an 8 mm trial to 10 mm flange welds (Trial and Verification) · 2022-10-03
- Beam introduction: restraint, shear, classification and bending (Beam Design Route) · 2022-10-03
- B1 floor beam: build design load from tributary width (Floor Load to Beam) · 2022-10-03
- B1: connect the previous lecture's loads to resistance checks (Beam Design Continuation) · 2022-10-17
- Local concentrated-force effects and initial section selection (Local Web Checks) · 2022-10-17
- B2: the internal beam and its corrected values (Interior Beam Results) · 2022-10-17
- B3: transferred reactions and formula corrections (Transferred Reactions) · 2022-10-17
- Unrestrained beams: from section strength to stability (Lateral-torsional Buckling) · 2022-10-17
- B2: lack of intermediate restraint reduces resistance (Unrestrained B2) · 2022-10-24
- B3: midspan restraint and table interpolation (Restraint and Interpolation) · 2022-10-24
- Overhanging beam Q5: separate load patterns before internal actions (Load Patterns) · 2022-10-24
- Introducing columns: effective length and two checking levels (Column Design Levels) · 2022-10-24
- Pure compression: two-axis slenderness and governing curves (Axial Column) · 2022-10-24
- Beam–column eccentricity and distribution between column segments (Simple Construction) · 2022-10-24
- Separate section and member levels in column design (Section versus Member) · 2022-10-31
- Example 5: retain moment signs through all three comparisons (Biaxial Worked Example) · 2022-10-31
- Q2: same section, new loading and effective length (Updated Column Inputs) · 2022-10-31
- Q3: a heavier section, all three checks (Heavier Section) · 2022-10-31
- Q5: derive biaxial moments from eccentric reactions (Eccentric Column Reactions) · 2022-10-31
- Q5 decision: a result slightly above 1 judged marginally OK (Interpreting a Marginal Result) · 2022-10-31
- 750 kN replay: double shear and two plates are different factors of 2 (Replay Identity) · 2022-11-07
- Return to 960 kN: complete all four calculations (Four Checks) · 2022-11-07
- Which plate does the replayed 818.2 kN belong to? (Net-section Capacity) · 2022-11-07
- Read conditions together with formulas (Formula Conditions) · 2022-11-14
- Weld and bolt revision: identify the current problem (Connection Revision) · 2022-11-14
- Assignment beams and columns: match formulas to the problem (Assignment Checks) · 2022-11-14
- Two floor beams: coexisting shear and independent SLS calculations (Beam Revision) · 2022-11-14
- Past-paper connections and columns: restate new data (Past-paper Data) · 2022-11-14
- LTB counterexample and segment restraints: Class 1 still needs stability (Stability Review) · 2022-11-14
- Final deflection problem: use units to check yourself (Deflection and Units) · 2022-11-14