FOUNDATIONS 4 / 4

Connections and stability

How bolts and welds pass the force on, and why a slender member becomes unstable before the steel is crushed.

Foundations

Several failure paths in a bolted connection (Bolted Connections)

In an ordinary bearing-type bolted connection, the plates transfer force to the bolts through contact at the hole walls. Failure may occur through bolt shear, bearing at the holes, tearing at a plate end or net-section rupture. Each mode uses different effective areas AeA_e, dimensions and strengths.

Double-cover splice: side viewEach half transfers the full axial force; each bolt has two shear planes
Supplementary schematic for understanding; not to scale.

Count shear planes from the side view. Two overlapping plates usually give one shear plane; a main plate sandwiched between two cover plates commonly gives two. The number of shear planes and the number of bolts are independent quantities.

Hole diameter d0d_0 is normally larger than bolt diameter dd. Use the course's tabulated effective area AeA_e for bolt shear, deduct hole diameter d0d_0 for plate net area AnA_n, and use dd as defined in the bearing expression. Confusing these three areas is a common beginner's mistake.

Ps=nspsAsP_s=n_sp_sA_s
Symbol / UnitMeaning
nsn_sNumber of effective shear planes per bolt
psp_sBolt design shear strength
AsA_sSpecified shear area in this course, mm²
Foundations

How holes weaken a steel plate (Net and Effective Area)

Take a section perpendicular to the tensile force and identify the steel remaining to transmit it. Gross area AgA_g is the area before deducting holes. Net area AnA_n is the area remaining after deducting the holes intersected by the failure path.

Deduct hole width × thickness along the failure section, not circle area
Supplementary schematic for understanding; not to scale.

For a straight path through nn circular holes in a plate of thickness tt, deduct n×d0×tn\times d_0\times t. This removes the hole widths from the tensile section, not the circular plan areas πd02/4d_0^{2}/4. Staggered holes or other failure paths require more than this one straight-line check.

Effective area AeA_e is a design quantity obtained by further adjusting the net area AnA_n for the material and connection form used in this course. KeAnK_eA_n must not exceed AgA_g. An angle connected through only one leg also requires a reduction for its outstanding leg. These factors are design rules, not purely geometric definitions of area.

An=(b−nd0)t,Ae=min⁡(KeAn,Ag)A_n=(b-nd_0)t,\qquad A_e=\min(K_eA_n,A_g)
Symbol / UnitMeaning
bbPlate width
d0d_0Hole diameter
AnA_n, AeA_e, AgA_gNet, effective and gross areas
Foundations

Leg size, throat and effective length (Fillet Weld Geometry)

The visible side dimension of a fillet weld is its leg size ss. The course takes effective throat aa as approximately 0.7s0.7s. For the same weld length, a larger throat gives more effective area for force transfer. A 6 mm leg is not a 6 mm effective throat.

Effective throat a ≈ 0.7sLeg size sqw = 0.7 s pw/1000 (kN/mm)
Supplementary schematic for understanding; not to scale.

pwp_w is weld design strength, obtained from the parent material and the course electrode classification table. Resistance per millimetre of effective weld length is qw=0.7spw/1000q_w=0.7sp_w/1000 in kN/mm. For a total force FF shared by similar welds, the initial total effective-length requirement is F/qwF/q_w.

Effective weld length differs from the actual length provided. In some course examples, 2s2s is added to effective length LwL_w before rounding up to a practical size, followed by checks of minimum length, lap and end returns. An eccentric weld group also needs moment components; total force divided by total length alone is insufficient.

qw=0.7spw/1000,Leff=F/qwq_w=0.7sp_w/1000,\qquad L_{eff}=F/q_w
Symbol / UnitMeaning
ssWeld leg size, mm
pwp_wWeld strength, N/mm²
qwq_wResistance per unit weld length, kN/mm
Foundations

Instability can precede material crushing (Buckling)

Yielding describes a material reaching the relevant stress state; buckling describes a compression member losing its original stable shape. A long ruler compressed lengthwise may bend sideways before all its material is crushed. This is why AgpyA_gp_y alone cannot assess a slender column.

Whole compression member bucklesλ = Le/rEnd restraints affect Le​
Supplementary schematic for understanding; not to scale.

Effective length LeL_e represents the influence of actual end restraints on the buckling shape. It may equal, be shorter than or exceed the physical length, depending on the supports and sway conditions. Slenderness ratio λ=Le/r\lambda=L_e/r combines length with the section's material distribution.

The course selects a buckling curve by section type, thickness and axis, then reads compressive strength pcp_c from λ\lambda and pyp_y. Complete the lookup for each axis before comparing capacities. Pc=AgpcP_c=A_gp_c already includes the reduction from that buckling method; do not treat it as AgpyA_gp_y.

λx=Lex/rx,λy=Ley/ry,Pc=Agpc\lambda_x=L_{ex}/r_x,\qquad\lambda_y=L_{ey}/r_y,\qquad P_c=A_gp_c
λx=Lex/rxλy=Ley/ryPc=Agpc\begin{aligned}\lambda_x&=L_{ex}/r_x\\\lambda_y&=L_{ey}/r_y\\P_c&=A_gp_c\end{aligned}
Symbol / UnitMeaning
pcp_cCompressive strength reduced for buckling
PcP_cMember compression resistance
KKEffective-length factor, Le=KLL_e=KL
Foundations

Why a beam moves sideways and twists (Lateral-torsional Buckling)

When a beam bends, one flange is in compression. Without adequate lateral restraint, that flange may move sideways and twist the whole section, causing lateral-torsional buckling (LTB). Adequate cross-sectional bending resistance McM_c does not rule out this overall instability.

Compression flange moves sideways while the section twistsLocate lateral restraints before choosing unrestrained length
Supplementary schematic for understanding; not to scale.

Locate the lateral and torsional restraints in the drawing before assigning an effective length LeL_e to each unrestrained segment. The course uses ryr_y, uu, xx, vv and βw\beta_{w} to convert ordinary slenderness λ\lambda to equivalent slenderness λLT\lambda_{LT}, then reads pbp_b and calculates Mb=pbSxM_b=p_bS_x. Obtain these parameters from the course method and section tables rather than guessing.

Moment may vary along the unrestrained segment, so an equivalent moment factor mLTm_{LT} adjusts demand. Compare mLTm_{LT} MM with MbM_b: mLTm_{LT} acts on demand and pbp_b on resistance; they are not interchangeable. Select the table case matching the actual bending moment diagram.

λLT=uvλβw,Mb=pbSx,mLTM≤Mb\lambda_{LT}=uv\lambda\sqrt{\beta_w},\qquad M_b=p_bS_x,\qquad m_{LT}M\le M_b
λLT=uvλβwMb=pbSxmLTM≤Mb\begin{aligned}\lambda_{LT}&=uv\lambda\sqrt{\beta_w}\\M_b&=p_bS_x\\m_{LT}M&\le M_b\end{aligned}
Symbol / UnitMeaning
βw\beta_{w}Parameter depending on section class; commonly 1 for Class 1/2 in this course
pbp_bBending buckling strength
mLTm_{LT}Equivalent moment factor
Foundations

Combined axial force and bending (Interaction Checks)

A column may bend as well as carry compression because of eccentric beam reactions RR or frame action. Axial force FcF_c and bending about both axes draw on its resistance simultaneously. Each separate demand being below its individual capacity does not establish that the combined action passes.

The course uses interaction equations that add dimensionless demand-to-resistance ratios. Section checks use AgpyA_gp_y and the corresponding section moment capacities McM_c. Member checks use PcP_c, specified elastic capacities, MbM_b and moment factors. Similar-looking expressions have different denominators and conditions of use.

Moment amplification addresses the additional effects required by the problem; equivalent moment factors describe the moment distribution. Amplify demand as specified, then apply the factors required by the chosen interaction equation. A sum greater than 1 fails that equation; an oral description of “marginal” does not relax the limit.

ηsection=FcAgpy+MxMcx+MyMcy≤1\eta_{section}=\frac{F_c}{A_gp_y}+\frac{M_x}{M_{cx}}+\frac{M_y}{M_{cy}}\le1
Symbol / UnitMeaning
FcF_cDesign axial compression force
MxM_x, MyM_yBending moments about both axes for the same design situation
McxM_{cx}, McyM_{cy}Must follow the definitions in the selected check
↑ Top