例題、術語及 formula 索引 (Reference)
逐步例題 · 按題型 (Worked Examples by Topic)
螺栓連接 (Bolted Connections)
- 兩顆 M20 連接 angle:把各項校核串起來 (Bolted Angle) · 2022-09-19
- 750 kN double cover plates splice:capacity 與孔距分開檢查 (Double-cover Splice) · 2022-09-19(亦見:2022-11-07)
- Q3:平面內 eccentric 螺栓群,逐顆合成 shear (In-plane Eccentric Bolts) · 2022-09-26
- Q4:bracket 螺栓的 shear、tension 與相互作用 (Shear–Tension Interaction) · 2022-09-26
- 960 kN測驗題:四項校核 (Four Checks) · 2022-11-07
- M27 plate bearing:逐項算清四個限制 (Four Bearing Limits) · 2022-11-14
焊接連接 (Welded Connections)
- 850 kN lap weld:effective weld length 與提供 weld length (Lap Weld) · 2022-10-03(亦見:2022-11-14)
- single angle 焊接:先查 member,再分配 weld length (Welded Angle) · 2022-10-03
- 65×50×8 angle:centroid 與不等 weld length · 2022-09-26
- 350 kN double angles:area 加總與兩側分配 (Double Angles) · 2022-10-03
- eccentric weld group Q6:由幾何到合力 (Eccentric Weld Group) · 2022-10-03
- Q7:flange 與 web weld 分工 (Bracket Flange and Web Welds) · 2022-10-03
steel beam (Beams)
- B1 floor beam:從 slab 到 strength 及 deflection (Complete Beam Walkthrough) · 2022-10-03(亦見:2022-10-17)
- B2:同一 floor 中的中間 beam · 2022-10-17
- B3:support reaction 變成下一根 beam 的 load (Reaction Transfer) · 2022-10-17
- B3 support 處:局部 web bearing 與 buckling (B3 Local Web Checks) · 2022-10-17
- 由 load 需求初選 section · 2022-10-17
- web 局部檢查:兩種模式都要過 (Web Bearing and Buckling) · 2022-10-17
- 6m複習 beam:co-existent shear 與 deflection (Coexistent Shear) · 2022-11-14
- 8m複習 beam:再做一次 capacity 與變形 (Beam Check Practice) · 2022-11-14
LTB (Lateral-torsional Buckling)
- 未 restraint B2:section 夠強仍會失穩 (Unrestrained Beam) · 2022-10-24
- 有跨中 restraint 的 B3:完成 LTB 流程 (Restrained Segments) · 2022-10-24
- overhanging beam Q5:分清 load 排列,再檢查AB段 (Overhanging Beam) · 2022-10-24
steel column (Columns)
- 純 axial compression UC column:兩軸查表到 capacity (Axial Compression) · 2022-10-24
- Example 5:non-sway frame column 的雙軸校核 (Biaxial Column) · 2022-10-31
- column Q2:305×305×118 UC的 section 及 member 校核 (Column Q2) · 2022-10-31
- column Q3:305×305×198 UC的 biaxial bending 校核 (Column Q3) · 2022-10-31
- Q5:利用率略大於1,老師判為 marginally OK (Marginal Utilization) · 2022-10-31
- simple construction column:beam 端 reaction 如何產生 column moment (Beam Reactions into Columns) · 2022-10-24
- 複習 column interaction formula:每個比值如何得來 (Column Interaction Review) · 2022-11-14
術語索引 (Terminology)
| 中文 | English | 簡單解釋 | 詳細 |
|---|---|---|---|
| 塑性截面模數 | Plastic Section Modulus | ;section 全面 yield 時的 bending 模數。 | 認識 I 形 section 與 section table (Section Properties) |
| 彈性截面模數 | Elastic Section Modulus | ;section 邊緣剛 yield 時的 bending 模數。 | 認識 I 形 section 與 section table (Section Properties) |
| 非側移框架 | Non-sway Frame | frame 受側向 load 時沒有明顯側移,column 的 effective length 較短。 | 材料尚未壓壞,member 也可能失穩 (Buckling) |
| 側扭屈曲 | Lateral-torsional Buckling, LTB | compression flange 側移並帶動 section 扭轉的整體失穩。 | beam 為甚麼會側移並扭轉 (Lateral-torsional Buckling) |
| 有效長度 | Effective Length | 按端部 restraint 換算後,用來計算 buckling 的長度。 | 材料尚未壓壞,member 也可能失穩 (Buckling) |
| 支座反力 | Support Reaction | support 為阻止 member 移動而產生的力。 | 物體為甚麼能保持不動 (Forces and Equilibrium) |
| 荷載路徑 | Load Path | load 由 slab 經 beam、column 傳到地面的路線。 | load 如何由 slab 走到地面 (Load Path) |
| 分擔寬度 | Tributary Width | 一根 beam 負責承托的 slab 寬度。 | load 如何由 slab 走到地面 (Load Path) |
| 截面分類 | Section Classification | 按 width-to-thickness ratio 把 section 分成Class 1至4,決定用哪條 bending formula。 | 薄板先皺起,還是材料先充分發揮 (Section Classification) |
| 局部屈曲 | Local Buckling | 薄板件 compression 時局部皺起。 | 薄板先皺起,還是材料先充分發揮 (Section Classification) |
| 截面模數 | Section Modulus | 把 stress 換成 moment capacity 的 section properties(或)。 | 認識 I 形 section 與 section table (Section Properties) |
| 迴轉半徑 | Radius of Gyration | ;用來計算 slenderness ratio。 | 認識 I 形 section 與 section table (Section Properties) |
| 有效面積 | Effective Area | net area 乘 factor,但不超過 gross area。 | 孔洞如何削弱 plate (Net and Effective Area) |
| 有效喉厚 | Effective Throat | fillet weld 承載用的厚度,約0.7倍 leg length。 | leg length、throat thickness 與 effective weld length (Fillet Weld Geometry) |
| 有效焊長 | Effective Weld Length | 扣除端部後計入 capacity 的 weld 長度。 | leg length、throat thickness 與 effective weld length (Fillet Weld Geometry) |
| 彎矩放大 | Moment Amplification | 考慮二階效應,把 moment 乘上 amplification factor。 | axial force 與 moment 共同作用 (Interaction Checks) |
| 均佈荷載 | Uniformly Distributed Load, UDL | 沿長度平均分布的 load,單位kN/m。 | 把實物轉成可計算的圖 (Free-body Diagram) |
| 彈性模數 | Elastic Modulus | ;本課取205000 N/mm²。 | 材料 strength 與 member capacity (Stress and Resistance) |
| 彎曲剛度 | Flexural Rigidity | ;越大越不易彎曲變形。 | 彎得太多與承載不足有何不同 (Deflection) |
| 剪切面積 | Shear Area | ;計算 shear capacity 用的 area,rolled I形 section 取。 | 認識 I 形 section 與 section table (Section Properties) |
| 極二次矩 | Polar Second Moment | ;weld group 抵抗扭轉的幾何性質。 | leg length、throat thickness 與 effective weld length (Fillet Weld Geometry) |
| 屈曲曲線 | Buckling Curve | 按 section 種類及軸向選用的表(曲線a至d)。 | 材料尚未壓壞,member 也可能失穩 (Buckling) |
| 塊狀剪切 | Block Shear | 螺栓群附近一整塊板沿 shear plane 及 tension 面撕出。 | 孔洞如何削弱 plate (Net and Effective Area) |
| 永久荷載 | Dead Load, DL | DL;結構 self-weight 及固定 equipment 等長期 load。 | 何時查 strength、何時查變形 (Limit States) |
| 施加荷載 | Imposed Load / Live Load, LL | LL;使用時的人、傢具等可變 load。 | 何時查 strength、何時查變形 (Limit States) |
| 鋼材等級 | Steel Grade | 按最低 yield strength 劃分的 steel 類別,例如 S355;它決定查 Data File 哪一欄。 | steel grade S275/S355/S460 與 strength 分類 (Steel Grade and Strength Classification) |
| 未乘係數 | Unfactored | load 的原本數值,還未乘 1.4 或 1.6 的 load factor。 | 何時查 strength、何時查變形 (Limit States) |
| 已乘係數 | Factored | 已經乘了 load factor 的 load,用來計 strength。 | 何時查 strength、何時查變形 (Limit States) |
| 荷載係數 | Load Factor | 計 strength 時乘在 load 上的安全 factor:dead load 1.4,live load 1.6。 | 何時查 strength、何時查變形 (Limit States) |
| 側向約束 | Lateral Restraint | 在旁邊扶着 beam 的 compression flange、不讓它向旁邊移動的 member。 | beam 為甚麼會側移並扭轉 (Lateral-torsional Buckling) |
| 細長比 | Slenderness Ratio | effective length 除以 radius of gyration,;越大越容易 buckling。 | 材料尚未壓壞,member 也可能失穩 (Buckling) |
| 受力圖 | Free-body Diagram | 把 member 單獨畫出,標上所有外力及 reaction 的圖。 | 把實物轉成可計算的圖 (Free-body Diagram) |
| 線荷載 | Line Load | 每米長度的 load,單位kN/m。 | 從單位判斷你正在算甚麼 (Units and Dimensions) |
| 面荷載 | Area Load | 每平方米的 load,單位kN/m²。 | 從單位判斷你正在算甚麼 (Units and Dimensions) |
| 慣性矩 | Second Moment of Area | ;section 抵 bending 曲變形的幾何性質,單位mm⁴或cm⁴。 | 認識 I 形 section 與 section table (Section Properties) |
| 利用率 | Utilization Ratio | 需求除以 capacity;不大於1才 OK。 | 材料 strength 與 member capacity (Stress and Resistance) |
| 淨面積 | Net Area | 扣除螺栓孔後的 section area。 | 孔洞如何削弱 plate (Net and Effective Area) |
| 毛面積 | Gross Area | 未扣孔的 section area。 | 孔洞如何削弱 plate (Net and Effective Area) |
| 角焊縫 | Fillet Weld | section 呈三角形的 weld,最常用的焊接方式。 | leg length、throat thickness 與 effective weld length (Fillet Weld Geometry) |
| 交互式 | Interaction Equation | 把 axial force 及兩軸 moment 的利用率相加,總和不大於1。 | axial force 與 moment 共同作用 (Interaction Checks) |
| 偏心距 | Eccentricity | 力的作用線到參考中心的垂直距離。 | 力的位置為甚麼重要 (Moment and Eccentricity) |
| 集中力 | Point Load | 作用在一點的力,單位kN。 | 把實物轉成可計算的圖 (Free-body Diagram) |
| 焊腳 | Leg Size | fillet weld 三角形的腰長。 | leg length、throat thickness 與 effective weld length (Fillet Weld Geometry) |
| 剪力 | Shear Force | section 兩側相對錯動的 internal force。 | beam 內部的 shear 與 moment |
| 彎矩 | Bending Moment | 使 member 彎曲的 internal force,單位kNm。 | 力的位置為甚麼重要 (Moment and Eccentricity) |
| 撓度 | Deflection | member 受荷後的下垂量,單位mm。 | 彎得太多與承載不足有何不同 (Deflection) |
| 應力 | Stress | 單位 area 上的力,單位N/mm²。 | 材料 strength 與 member capacity (Stress and Resistance) |
| 屈服 | Yielding | steel 達到 yield strength 後開始大量 plastic 變形。 | 材料 strength 與 member capacity (Stress and Resistance) |
| 屈曲 | Buckling | compression member 在材料壓壞前突然彎曲失穩。 | 材料尚未壓壞,member 也可能失穩 (Buckling) |
| 翼緣 | Flange | I形 section 上下兩塊橫板。 | 認識 I 形 section 與 section table (Section Properties) |
| 腹板 | Web | I形 section 中間的豎板。 | 認識 I 形 section 與 section table (Section Properties) |
| 端距 | End Distance | 沿傳力方向,孔中心到板端的距離。 | 螺栓 joint 有多條破壞路徑 (Bolted Connections) |
| 孔徑 | Hole Diameter | 螺栓孔的 diameter,比螺栓 diameter 大。 | 螺栓 joint 有多條破壞路徑 (Bolted Connections) |
| 單剪 | Single Shear | 螺栓只有一個 shear plane。 | 螺栓 joint 有多條破壞路徑 (Bolted Connections) |
| 雙剪 | Double Shear | 螺栓有兩個 shear plane,shear capacity 乘2。 | 螺栓 joint 有多條破壞路徑 (Bolted Connections) |
| 承壓 | Bearing | 螺栓與孔壁互相擠壓的作用。 | 螺栓 joint 有多條破壞路徑 (Bolted Connections) |
| 應變 | Strain | 單位長度的伸長或縮短。 | 材料 strength 與 member capacity (Stress and Resistance) |
| 形心 | Centroid | section 或 weld group 的幾何中心。 | 力的位置為甚麼重要 (Moment and Eccentricity) |
| 回焊 | End Return | weld 在端部轉角延續的一小段。 | leg length、throat thickness 與 effective weld length (Fillet Weld Geometry) |
| 力矩 | Moment | 力乘以垂直距離,使物體轉動的作用。 | 力的位置為甚麼重要 (Moment and Eccentricity) |
| 板件 | Plate Element | section 或 joint 中的一塊 plate,例如 flange、web 或 cover plate。 | 薄板先皺起,還是材料先充分發揮 (Section Classification) |
| 裕度 | Margin | capacity 比需求多出的部分;裕度小,表示接近限值。 | 材料 strength 與 member capacity (Stress and Resistance) |
| 工況 | Load Case | 一種 load 的擺放方式;不同的擺法令不同位置的 internal force 最大。 | 何時查 strength、何時查變形 (Limit States) |
| 細部 | Detailing | 孔距、end distance、最小 leg length 等尺寸規定;capacity 足夠之後仍要符合。 | 螺栓 joint 有多條破壞路徑 (Bolted Connections) |
| 插值 | Interpolation | 數值落在表中兩行之間時,按比例取中間的值。 | 查表和 interpolation |
| 需求 | Demand | load 在 member 上造成的力或 moment。 | 材料 strength 與 member capacity (Stress and Resistance) |
| 容量 | Capacity | member 或 joint 最多可以承受的力或 moment。 | 材料 strength 與 member capacity (Stress and Resistance) |
基礎 formula 與條件 (Foundational Formulae)
從單位判斷你正在算甚麼 (Units and Dimensions)
符號、單位及適用條件見連結的基礎單元。
查表和 interpolation
符號、單位及適用條件見連結的基礎單元。
材料 strength 與 member capacity (Stress and Resistance)
符號、單位及適用條件見連結的基礎單元。
物體為甚麼能保持不動 (Forces and Equilibrium)
符號、單位及適用條件見連結的基礎單元。
力的位置為甚麼重要 (Moment and Eccentricity)
符號、單位及適用條件見連結的基礎單元。
load 如何由 slab 走到地面 (Load Path)
符號、單位及適用條件見連結的基礎單元。
beam 內部的 shear 與 moment
符號、單位及適用條件見連結的基礎單元。
認識 I 形 section 與 section table (Section Properties)
符號、單位及適用條件見連結的基礎單元。
steel grade S275/S355/S460 與 strength 分類 (Steel Grade and Strength Classification)
符號、單位及適用條件見連結的基礎單元。
何時查 strength、何時查變形 (Limit States)
符號、單位及適用條件見連結的基礎單元。
薄板先皺起,還是材料先充分發揮 (Section Classification)
符號、單位及適用條件見連結的基礎單元。
彎得太多與承載不足有何不同 (Deflection)
符號、單位及適用條件見連結的基礎單元。
螺栓 joint 有多條破壞路徑 (Bolted Connections)
符號、單位及適用條件見連結的基礎單元。
孔洞如何削弱 plate (Net and Effective Area)
符號、單位及適用條件見連結的基礎單元。
leg length、throat thickness 與 effective weld length (Fillet Weld Geometry)
符號、單位及適用條件見連結的基礎單元。
材料尚未壓壞,member 也可能失穩 (Buckling)
符號、單位及適用條件見連結的基礎單元。
beam 為甚麼會側移並扭轉 (Lateral-torsional Buckling)
符號、單位及適用條件見連結的基礎單元。
axial force 與 moment 共同作用 (Interaction Checks)
符號、單位及適用條件見連結的基礎單元。
課堂設計 formula 查閱 (Design Formula Index)
以下連結到有 formula 或例題的單元。表列設計 factor 來自守則,不是由基本平衡推導出來的。
- 把 limit state 與使用狀態分開 (Ultimate and Serviceability Limit States) · 2022-09-19
- 先認識 section table,再做分類 (Section Tables and Classification) · 2022-09-19
- 普通螺栓的傳力與 bearing · 2022-09-19
- 第一道 angle joint 題:先完成 shear (Angle Connection Example) · 2022-09-19
- 老師接著做750 kN splice,並修改孔距 (Splice Layout Check) · 2022-09-19
- 回到 angle:毛、淨與 effective area (Gross, Net and Effective Area) · 2022-09-19
- 從 formula 表回到 joint 幾何 (Connection Geometry) · 2022-09-26
- 兩種 eccentric:先看 joint 如何轉動 (Two Eccentricity Models) · 2022-09-26
- Q3:修正單側 load 後重新求合力 (Correcting the Load Share) · 2022-09-26
- Q4:個別 OK 後還要檢查組合 (Interaction Check) · 2022-09-26
- 焊接從 throat thickness 與傳力 area 開始 (Fillet Weld Basics) · 2022-09-26
- angle centroid 分配,再接到 lap weld (Centroid and Weld Length) · 2022-09-26
- 850 kN lap weld:weld length、最低 leg length 與 plate · 2022-10-03
- bracket weld:先分工,再求需求 (Bracket Weld Model) · 2022-10-03
- single angle 與 double angles:方法相同、factor 不同 (Single and Double Angles) · 2022-10-03
- Q6:eccentric weld group 逐段求合力 (Eccentric Weld Group) · 2022-10-03
- Q7:600 kN bracket,由8 mm試選到10 mm flange 焊 (Trial and Verification) · 2022-10-03
- steel beam 入門:restraint、shear、分類與 moment (Beam Design Route) · 2022-10-03
- B1 floor beam:由 slab tributary width 建立 design load (Floor Load to Beam) · 2022-10-03
- B1:把前一課的 load 接到 capacity 校核 (Beam Design Continuation) · 2022-10-17
- point load 附近的局部問題與 section 初選 (Local Web Checks) · 2022-10-17
- B2:中間 beam 與修正後數值 (Interior Beam Results) · 2022-10-17
- B3:reaction 傳遞與 formula 修正 (Transferred Reactions) · 2022-10-17
- 未 restraint beam:從 section strength 走向穩定 (Lateral-torsional Buckling) · 2022-10-17
- B2:capacity 不足來自無中間 lateral restraint (Unrestrained B2) · 2022-10-24
- B3:跨中 restraint 與查表 interpolation · 2022-10-24
- overhanging beam Q5:先分 case,再畫 internal force (Load Patterns) · 2022-10-24
- 轉入 column:effective length 與兩種校核層次 (Column Design Levels) · 2022-10-24
- 純 axial compression column:兩軸 slenderness ratio 與控制曲線 (Axial Column) · 2022-10-24
- beam column 連接的 eccentric 與上下 column segment 分配 (Simple Construction) · 2022-10-24
- column 設計先分 section 與 member · 2022-10-31
- Example5:保留端 moment 符號,完成三層比較 (Biaxial Worked Example) · 2022-10-31
- Q2:同一 section,新的 load 與 effective length (Updated Column Inputs) · 2022-10-31
- Q3:較重 section,完成三條校核 (Heavier Section) · 2022-10-31
- Q5:由 eccentric reaction 求雙軸 moment (Eccentric Column Reactions) · 2022-10-31
- Q5終判:略大於1的 marginally OK (Interpreting a Marginal Result) · 2022-10-31
- 重播750 kN:double shear 與兩片板不是同一個2 (Replay Identity) · 2022-11-07
- 回到960 kN:完成四項計算 (Four Checks) · 2022-11-07
- 重播的818.2 kN屬哪一片板 (Net-section Capacity) · 2022-11-07
- formula 與分類:條件要跟著 formula 一起讀 (Formula Conditions) · 2022-11-14
- 焊接與螺栓複習:先辨認正在算哪一道題 (Connection Revision) · 2022-11-14
- 作業 beam 與 column:同一 formula 仍要配對題目 (Assignment Checks) · 2022-11-14
- 兩道 floor beam:co-existent shear 與SLS獨立計算 (Beam Revision) · 2022-11-14
- 往年連接與 column 題:新題先重列資料 (Past-paper Data) · 2022-11-14
- LTB反例與分段 restraint:Class1仍須驗穩定 (Stability Review) · 2022-11-14
- 最後一題 deflection:用單位作自我檢查 (Deflection and Units) · 2022-11-14