| Pastpaper/13CNTM022.pdf · p.2 · AQ1-a-ii | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/13CNTM022.pdf · p.2 · AQ1-a-iv | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/13CNTM022.pdf · p.2 · AQ1-a-v | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/13CNTM022.pdf · p.3 · BQ2-a | Exact 178×89×26.81 channel properties are absent from all supplied section tables; no numeric final channel bearing/tension certificate can be derived. |
| Pastpaper/13CNTM022.pdf · p.4 · BQ2-b | Supporting thickness is absent. The selected leg size is a strength trial for a continuous effective-line rectangle; minimum/maximum weld size and support adequacy remain incomplete. |
| Pastpaper/13CNTM022.pdf · p.4 · BQ3 | The non-sway course end-moment model is assumed because sway/restraint details are not stated. |
| Pastpaper/13CNTM022.pdf · p.5 · BQ4-c | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/14ENGTY157.pdf · p.2 · AQ1-a-ii | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/14ENGTY157.pdf · p.2 · AQ1-a-iv | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/14ENGTY157.pdf · p.2 · AQ1-a-v | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/14ENGTY157.pdf · p.3 · BQ2-b | Supporting thickness and precise weld-centroid separation are absent; the shown/given ordinary edge-weld detail also fails the course maximum-size check. Strength calculation and required redesign are supplied. |
| Pastpaper/14ENGTY157.pdf · p.5 · BQ4-c | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/14IIENGTY142.pdf · p.2 · AQ1-a-ii | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/14IIENGTY142.pdf · p.2 · AQ1-a-iv | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/14IIENGTY142.pdf · p.2 · AQ1-a-v | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/14IIENGTY142.pdf · p.3 · BQ2-a-iii | M20 passes shear and a rolled/machined 25 mm minimum end distance, but the 30 mm shown is below the 35 mm sheared-edge minimum. Edge preparation is unspecified; use the stated rolled/machined branch or increase the distance. |
| Pastpaper/14IIENGTY142.pdf · p.4 · BQ3 | The non-sway course end-moment model is assumed because sway/restraint details are not stated. |
| Pastpaper/14IIENGTY142.pdf · p.5 · BQ4-c | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. The supplied UDL action pair is inconsistent. |
| Pastpaper/15ENGTY028.pdf · p.2 · AQ1-a-ii | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/15ENGTY028.pdf · p.2 · AQ1-a-iv | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/15ENGTY028.pdf · p.2 · AQ1-a-v | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/15ENGTY028.pdf · p.4 · BQ1-b-i | Transverse bolt gauge is missing. The no-prying calculation is conditional on G ≤ 170.06 mm and suitable plate/support behaviour; final connection adequacy incomplete. |
| Pastpaper/15ENGTY028.pdf · p.4 · BQ1-b-ii | Transverse bolt gauge is missing. The no-prying calculation is conditional on G ≤ 170.06 mm and suitable plate/support behaviour; final connection adequacy incomplete. |
| Pastpaper/15ENGTY028.pdf · p.6 · BQ3-c | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/15IIENGTY037.pdf · p.2 · AQ1-i | Concrete unit weight is absent. Numerical branch assumes 24.5 kN/m³; the general expression retains γc. Finish brittleness is unspecified: both L/360 and L/200 limits are shown. |
| Pastpaper/15IIENGTY037.pdf · p.2 · AQ1-ii | Concrete unit weight is absent. Numerical branch assumes 24.5 kN/m³; the general expression retains γc. Finish brittleness is unspecified: both L/360 and L/200 limits are shown. |
| Pastpaper/15IIENGTY037.pdf · p.2 · AQ1-iv | Concrete unit weight is absent. Numerical branch assumes 24.5 kN/m³; the general expression retains γc. Finish brittleness is unspecified: both L/360 and L/200 limits are shown. |
| Pastpaper/15IIENGTY037.pdf · p.2 · AQ1-v | Concrete unit weight is absent. Numerical branch assumes 24.5 kN/m³; the general expression retains γc. Finish brittleness is unspecified: both L/360 and L/200 limits are shown. |
| Pastpaper/15IIENGTY037.pdf · p.3 · AQ1-vi | Concrete unit weight and SHS wall thickness are absent; final weld size/support adequacy incomplete. |
| Pastpaper/15IIENGTY037.pdf · p.4 · BQ2-ii | Column designation is truncated to “254×254×8”; flange thickness and transverse edge distance cannot be identified. Bolt forces and side-plate basic capacity are calculable, but final connected-part adequacy is incomplete. |
| Pastpaper/15IIENGTY037.pdf · p.6 · BQ4-b-iv | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/15IIENGTY045.pdf · p.2 · AQ1-a-ii | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/15IIENGTY045.pdf · p.2 · AQ1-a-iv | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/15IIENGTY045.pdf · p.2 · AQ1-a-v | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/15IIENGTY045.pdf · p.4 · BQ2-b | Supporting thickness and precise weld-centroid separation are absent; the shown/given ordinary edge-weld detail also fails the course maximum-size check. Strength calculation and required redesign are supplied. |
| Pastpaper/15IIENGTY045.pdf · p.4 · BQ3 | The non-sway course end-moment model is assumed because sway/restraint details are not stated. |
| Pastpaper/15IIENGTY045.pdf · p.5 · BQ4-b | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/15IIENGTY045.pdf · p.5 · BQ4-c | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/16ENGTY055.pdf · p.2 · AQ1-a-ii | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/16ENGTY055.pdf · p.2 · AQ1-a-iv | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/16ENGTY055.pdf · p.2 · AQ1-a-v | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/16ENGTY055.pdf · p.3 · BQ1-a-iii | The main-plate butt is not dimensioned relative to the inner bolt columns. The numerical branch assumes equal half-spacing and e = 50 mm; retain the symbolic end-distance limit for another butt position. |
| Pastpaper/16ENGTY055.pdf · p.3 · BQ1-a-v | The main-plate butt is not dimensioned relative to the inner bolt columns. The numerical branch assumes equal half-spacing and e = 50 mm; retain the symbolic end-distance limit for another butt position. |
| Pastpaper/16ENGTY055.pdf · p.3 · BQ1-b | Supporting thickness is absent. The selected leg size is a strength trial for a continuous effective-line rectangle; minimum/maximum weld size and support adequacy remain incomplete. |
| Pastpaper/16ENGTY055.pdf · p.5 · BQ3-c | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/16ENGTY055.pdf · p.5 · BQ3-d | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/16IIENGTY048.pdf · p.2 · AQ1-a-ii | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/16IIENGTY048.pdf · p.2 · AQ1-a-iv | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/16IIENGTY048.pdf · p.2 · AQ1-a-v | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/16IIENGTY048.pdf · p.3 · BQ1-a-v | Text says 203×203×71 UC but the drawing says 254×254×107 UC. Both branches have flange thickness above 12 mm, so the side plate bounds bearing under identical clearances; final column identity/detailing remains incomplete. |
| Pastpaper/16IIENGTY048.pdf · p.5 · BQ2 | The 2017 PTE text calls the 150 mm offset a y-axis distance; the dimensioned drawing places it above x–x. This solution follows the diagram. |
| Pastpaper/16IIENGTY048.pdf · p.6 · BQ3-c | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/16IIENGTY048.pdf · p.6 · BQ3-d | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/17ENGTY007.pdf · p.2 · AQ1-a-ii | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/17ENGTY007.pdf · p.2 · AQ1-a-iv | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/17ENGTY007.pdf · p.2 · AQ1-a-v | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/17ENGTY007.pdf · p.5 · BQ2 | The non-sway course end-moment model is assumed because sway/restraint details are not stated. |
| Pastpaper/17ENGTY007.pdf · p.6 · BQ3-c | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/17ENGTY007.pdf · p.6 · BQ3-d | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/17IIENGTY021.pdf · p.2 · AQ1-a-ii | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/17IIENGTY021.pdf · p.2 · AQ1-a-iv | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/17IIENGTY021.pdf · p.2 · AQ1-a-v | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/17IIENGTY021.pdf · p.3 · BQ1-a-iii | The main-plate butt is not dimensioned relative to the inner bolt columns. The numerical branch assumes equal half-spacing and e = 35 mm; retain the symbolic end-distance limit for another butt position. |
| Pastpaper/17IIENGTY021.pdf · p.3 · BQ1-a-iv | The main-plate butt is not dimensioned relative to the inner bolt columns. The numerical branch assumes equal half-spacing and e = 35 mm; retain the symbolic end-distance limit for another butt position. |
| Pastpaper/17IIENGTY021.pdf · p.3 · BQ1-b | Supporting thickness is absent. The selected leg size is a strength trial for a continuous effective-line rectangle; minimum/maximum weld size and support adequacy remain incomplete. |
| Pastpaper/17IIENGTY021.pdf · p.5 · BQ3-c | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/17IIENGTY021.pdf · p.5 · BQ3-d | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/17IIENGTY028.pdf · p.2 · Q1-a-iii | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/17IIENGTY028.pdf · p.2 · Q1-a-iv | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/17IIENGTY028.pdf · p.4 · BQ1-b-i | Transverse bolt gauge is missing. The no-prying calculation is conditional on G ≤ 170.06 mm and suitable plate/support behaviour; final connection adequacy incomplete. |
| Pastpaper/17IIENGTY028.pdf · p.4 · BQ1-b-ii | Transverse bolt gauge is missing. The no-prying calculation is conditional on G ≤ 170.06 mm and suitable plate/support behaviour; final connection adequacy incomplete. |
| Pastpaper/17IIENGTY028.pdf · p.5 · Q4-c | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. The supplied UDL action pair is inconsistent. |
| Pastpaper/18ENGTY025.pdf · p.2 · AQ1-a-ii | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/18ENGTY025.pdf · p.2 · AQ1-a-iv | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/18ENGTY025.pdf · p.2 · AQ1-a-v | g is not printed. Numerical self-weight adopts the course convention g = 10 m/s²; replace only mass-to-force terms if using 9.81. |
| Pastpaper/18ENGTY025.pdf · p.3 · BQ1-a-iii | The main-plate butt is not dimensioned relative to the inner bolt columns. The numerical branch assumes equal half-spacing and e = 50 mm; retain the symbolic end-distance limit for another butt position. |
| Pastpaper/18ENGTY025.pdf · p.3 · BQ1-a-iv | The main-plate butt is not dimensioned relative to the inner bolt columns. The numerical branch assumes equal half-spacing and e = 50 mm; retain the symbolic end-distance limit for another butt position. |
| Pastpaper/18ENGTY025.pdf · p.3 · BQ1-b | Supporting thickness is absent. The selected leg size is a strength trial for a continuous effective-line rectangle; minimum/maximum weld size and support adequacy remain incomplete. |
| Pastpaper/18ENGTY025.pdf · p.5 · BQ3-c | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |
| Pastpaper/18ENGTY025.pdf · p.5 · BQ3-d | Lateral points are shown, but load height and full torsional/end restraint details are absent. Numerical resistance uses the explicit normal-loading LE = restraint-spacing model; final restraint adequacy remains incomplete. |