Steelwork · Exam learning

2014–2019 · Reference answers

2014-01-09 — floor and foundations

Solve the complete compulsory question, using the original diagram beside the calculation.

Independent teaching answer, not an official solution or marking scheme. Printed marks are retained. Read the source conditions beside each result.

Read the load path first

The slab arrows point across adjacent B1 beams. Each interior B1 collects half the 2 m bay on either side: tributary width 2 m. Its labelled span is 6 m. The supporting B2 spans 4 m between the drawn columns and receives 1 B1 end reaction(s), at its middle.

Beams aligned directly with a column deliver their end reaction to that column, not as an extra midspan load on B2. The B2 point load is already factored; do not factor it again. The slab gives full compression-flange restraint, so this is section resistance rather than an LTB design.

Units: 1 kN = 1,000 N; 1 m = 1,000 mm; 1 cm³ = 1,000 mm³; 1 cm⁴ = 10,000 mm⁴. A demand is the load effect; a resistance is what the member can carry. Compare matching units.

Simple explanation — open only if needed

Think of a tray resting on small bars, then on two larger edge bars. Follow where each bar ends: that determines which reaction goes onto the next bar.

Load intensity [4 marks]

Given slab thickness 150 mm, finishes 5 kN/m², imposed load 3 kN/m². Convert thickness to metres. Permanent area load includes concrete and finishes; beam weight is added later as a line load.

gk=hγc+gfin=0.15(24)+5=8.6 kN/m2g_k=h\gamma_c+g_{fin}=0.15(24)+5=8.6\,\mathrm{kN/m^2}
qu=1.4gk+1.6qk=1.4(8.6)+1.6(3)=16.84 kN/m2q_u=1.4g_k+1.6q_k=1.4(8.6)+1.6(3)=16.84\,\mathrm{kN/m^2}
Compact exam answer — key result lines
gk=hγc+gfin=0.15(24)+5=8.6 kN/m2g_k=h\gamma_c+g_{fin}=0.15(24)+5=8.6\,\mathrm{kN/m^2}
qu=1.4gk+1.6qk=1.4(8.6)+1.6(3)=16.84 kN/m2q_u=1.4g_k+1.6q_k=1.4(8.6)+1.6(3)=16.84\,\mathrm{kN/m^2}

Given slab thickness 150 mm, finishes 5 kN/m², imposed load 3 kN/m². Convert thickness to metres. Permanent area load includes concrete and finishes; beam weight is added later as a line load.

Beam actions [8 marks]

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.9, p.10

Lookup the exact 305 × 165 × 40 UB row. Read dimensions first, properties second. D = overall depth; t = web thickness; T = flange thickness; d = clear web depth. The designation is not an exact dimension.

D=303.4, t=6, T=10.2, d=265.2(mm)D=303.4,\ t=6,\ T=10.2,\ d=265.2\quad(\mathrm{mm})
b/T=8.09, d/t=44.2, Ix=8503 cm4, Zx=560 cm3, Sx=623 cm3b/T=8.09,\ d/t=44.2,\ I_x=8503\,\mathrm{cm^4},\ Z_x=560\,\mathrm{cm^3},\ S_x=623\,\mathrm{cm^3}
ry=38.6 mm,u=0.889,x=31r_y=38.6\,\mathrm{mm},\quad u=0.889,\quad x=31
Source: LectureNotes/CON4334-Data File-20260730.pdf · p.9, p.10

Lookup the exact 356 × 171 × 45 UB row. Read dimensions first, properties second. D = overall depth; t = web thickness; T = flange thickness; d = clear web depth. The designation is not an exact dimension.

D=351.4, t=7, T=9.7, d=311.6(mm)D=351.4,\ t=7,\ T=9.7,\ d=311.6\quad(\mathrm{mm})
b/T=8.82, d/t=44.5, Ix=12070 cm4, Zx=687 cm3, Sx=775 cm3b/T=8.82,\ d/t=44.5,\ I_x=12070\,\mathrm{cm^4},\ Z_x=687\,\mathrm{cm^3},\ S_x=775\,\mathrm{cm^3}
ry=37.6 mm,u=0.874,x=36.8r_y=37.6\,\mathrm{mm},\quad u=0.874,\quad x=36.8

Lookup mass in kg/m and multiply by g/1000 to get kN/m. Multiply the slab area load by the tributary width, not by the full slab area.

wg1=40.3(10)/1000=0.403,wg2=45(10)/1000=0.45(kN/m)w_{g1}=40.3(10)/1000=0.403,\quad w_{g2}=45(10)/1000=0.45\quad(\mathrm{kN/m})
wu1=qub+1.4wg1=16.84(2)+1.4(0.403)=34.2442 kN/mw_{u1}=q_ub+1.4w_{g1}=16.84(2)+1.4(0.403)=34.2442\,\mathrm{kN/m}
V1=R1=wu1L1/2=34.2442(6)/2=102.7326 kNV_1=R_1=w_{u1}L_1/2=34.2442(6)/2=102.7326\,\mathrm{kN}
M1=wu1L12/8=34.2442(62)/8=154.0989 kN mM_1=w_{u1}L_1^2/8=34.2442(6^2)/8=154.0989\,\mathrm{kN\,m}

For B2 use superposition: the B1 point reactions plus B2 self-weight. Equilibrium divides the symmetric total load equally between the supports.

wu2=1.4(0.45)=0.63 kN/m,P=R1=102.7326 kNw_{u2}=1.4(0.45)=0.63\,\mathrm{kN/m},\quad P=R_1=102.7326\,\mathrm{kN}
V2=1P+wu2L22=1(102.7326)+0.63(4)2=52.6263 kNV_2=\frac{1P+w_{u2}L_2}{2}=\frac{1(102.7326)+0.63(4)}{2}=52.6263\,\mathrm{kN}
M2=PL24+wu2L228=102.7326(4)4+0.63(42)8=103.9926 kN mM_2=\frac{PL_2}{4}+\frac{w_{u2}L_2^2}{8}=\frac{102.7326(4)}{4}+\frac{0.63(4^2)}{8}=103.9926\,\mathrm{kN\,m}
Compact exam answer — key result lines
V1=R1=wu1L1/2=34.2442(6)/2=102.7326 kNV_1=R_1=w_{u1}L_1/2=34.2442(6)/2=102.7326\,\mathrm{kN}
M1=wu1L12/8=34.2442(62)/8=154.0989 kN mM_1=w_{u1}L_1^2/8=34.2442(6^2)/8=154.0989\,\mathrm{kN\,m}
wu2=1.4(0.45)=0.63 kN/m,P=R1=102.7326 kNw_{u2}=1.4(0.45)=0.63\,\mathrm{kN/m},\quad P=R_1=102.7326\,\mathrm{kN}
V2=1P+wu2L22=1(102.7326)+0.63(4)2=52.6263 kNV_2=\frac{1P+w_{u2}L_2}{2}=\frac{1(102.7326)+0.63(4)}{2}=52.6263\,\mathrm{kN}
M2=PL24+wu2L228=102.7326(4)4+0.63(42)8=103.9926 kN mM_2=\frac{PL_2}{4}+\frac{w_{u2}L_2^2}{8}=\frac{102.7326(4)}{4}+\frac{0.63(4^2)}{8}=103.9926\,\mathrm{kN\,m}

For B2 use superposition: the B1 point reactions plus B2 self-weight. Equilibrium divides the symmetric total load equally between the supports.

Section classes [4 marks]

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.1

S355 design strength depends on the actual flange thickness. Local classification decides whether plastic bending resistance is allowed. In pure bending the web limit is different from uniform compression.

py=355 N/mm2,ϵ=275/355=0.880141p_y=355\,\mathrm{N/mm^2},\quad\epsilon=\sqrt{275/355}=0.880141
b/T=8.09,9ϵ=7.921,10ϵ=8.801,13ϵ=11.442b/T=8.09,\quad9\epsilon=7.921,\quad10\epsilon=8.801,\quad13\epsilon=11.442
d/t=44.2<80ϵ=70.411⟹Class 2d/t=44.2<80\epsilon=70.411\quad\Longrightarrow\quad\mathrm{Class}\ 2

Take the worse flange/web class. Class 1 or 2 permits the capped plastic modulus; Class 3 uses the elastic modulus.

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.1

S355 design strength depends on the actual flange thickness. Local classification decides whether plastic bending resistance is allowed. In pure bending the web limit is different from uniform compression.

py=355 N/mm2,ϵ=275/355=0.880141p_y=355\,\mathrm{N/mm^2},\quad\epsilon=\sqrt{275/355}=0.880141
b/T=8.82,9ϵ=7.921,10ϵ=8.801,13ϵ=11.442b/T=8.82,\quad9\epsilon=7.921,\quad10\epsilon=8.801,\quad13\epsilon=11.442
d/t=44.5<80ϵ=70.411⟹Class 3d/t=44.5<80\epsilon=70.411\quad\Longrightarrow\quad\mathrm{Class}\ 3

Take the worse flange/web class. Class 1 or 2 permits the capped plastic modulus; Class 3 uses the elastic modulus.

Compact exam answer — key result lines
b/T=8.09,9ϵ=7.921,10ϵ=8.801,13ϵ=11.442b/T=8.09,\quad9\epsilon=7.921,\quad10\epsilon=8.801,\quad13\epsilon=11.442
d/t=44.2<80ϵ=70.411⟹Class 2d/t=44.2<80\epsilon=70.411\quad\Longrightarrow\quad\mathrm{Class}\ 2
py=355 N/mm2,ϵ=275/355=0.880141p_y=355\,\mathrm{N/mm^2},\quad\epsilon=\sqrt{275/355}=0.880141
b/T=8.82,9ϵ=7.921,10ϵ=8.801,13ϵ=11.442b/T=8.82,\quad9\epsilon=7.921,\quad10\epsilon=8.801,\quad13\epsilon=11.442
d/t=44.5<80ϵ=70.411⟹Class 3d/t=44.5<80\epsilon=70.411\quad\Longrightarrow\quad\mathrm{Class}\ 3

Take the worse flange/web class. Class 1 or 2 permits the capped plastic modulus; Class 3 uses the elastic modulus.

B1 checks [10 marks]

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.2

The web carries shear. For a rolled UB use Av = Dt, then the course shear resistance pyAv/√3. The 0.6 factor below is the low-shear threshold; it is not the coefficient in the shear-resistance formula.

Av=303.4(6)=1820.4 mm2A_v=303.4(6)=1820.4\,\mathrm{mm^2}
Vc=pyAv3=355(1820.4)3(1000)=373.107993 kNV_c=\frac{p_yA_v}{\sqrt3}=\frac{355(1820.4)}{\sqrt3(1000)}=373.107993\,\mathrm{kN}
V=102.7326 kN,V/Vc=0.275343,0.6Vc=223.864796 kNV=102.7326\,\mathrm{kN},\quad V/V_c=0.275343,\quad0.6V_c=223.864796\,\mathrm{kN}

PASS

Mc=min⁡(pySx,1.2pyZx)/1000=min⁡(355(623),1.2(355)(560))/1000=221.165 kN mM_c=\min(p_yS_x,1.2p_yZ_x)/1000=\min(355(623),1.2(355)(560))/1000=221.165\,\mathrm{kN\,m}
M/Mc=154.0989/221.165=0.69676M/M_c=154.0989/221.165=0.69676

PASS

Even the maximum shear is below 0.6Vc, so the low-shear moment resistance applies throughout.

For serviceability use unfactored imposed load only, E = 205,000 N/mm², I in mm⁴ and span in mm. Do not include the ULS factors or dead load in this course deflection limit.

δ1=5wQL14384EI1=5(3(2))(6000)4384(205000)(8503×104)=5.808567 mm\delta_1=\frac{5w_QL_1^4}{384EI_1}=\frac{5(3(2))(6000)^4}{384(205000)(8503\times10^4)}=5.808567\,\mathrm{mm}
δlim=L/360=6000/360=16.666667 mm\delta_{lim}=L/360=6000/360=16.666667\,\mathrm{mm}

PASS

Compact exam answer — key result lines
V=102.7326 kN,V/Vc=0.275343,0.6Vc=223.864796 kNV=102.7326\,\mathrm{kN},\quad V/V_c=0.275343,\quad0.6V_c=223.864796\,\mathrm{kN}
Mc=min⁡(pySx,1.2pyZx)/1000=min⁡(355(623),1.2(355)(560))/1000=221.165 kN mM_c=\min(p_yS_x,1.2p_yZ_x)/1000=\min(355(623),1.2(355)(560))/1000=221.165\,\mathrm{kN\,m}
M/Mc=154.0989/221.165=0.69676M/M_c=154.0989/221.165=0.69676
δ1=5wQL14384EI1=5(3(2))(6000)4384(205000)(8503×104)=5.808567 mm\delta_1=\frac{5w_QL_1^4}{384EI_1}=\frac{5(3(2))(6000)^4}{384(205000)(8503\times10^4)}=5.808567\,\mathrm{mm}
δlim=L/360=6000/360=16.666667 mm\delta_{lim}=L/360=6000/360=16.666667\,\mathrm{mm}

PASS

B2 checks [10 marks]

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.2

The web carries shear. For a rolled UB use Av = Dt, then the course shear resistance pyAv/√3. The 0.6 factor below is the low-shear threshold; it is not the coefficient in the shear-resistance formula.

Av=351.4(7)=2459.8 mm2A_v=351.4(7)=2459.8\,\mathrm{mm^2}
Vc=pyAv3=355(2459.8)3(1000)=504.158998 kNV_c=\frac{p_yA_v}{\sqrt3}=\frac{355(2459.8)}{\sqrt3(1000)}=504.158998\,\mathrm{kN}
V=52.6263 kN,V/Vc=0.104384,0.6Vc=302.495399 kNV=52.6263\,\mathrm{kN},\quad V/V_c=0.104384,\quad0.6V_c=302.495399\,\mathrm{kN}

PASS

Mc=pyZx/1000=355(687)/1000=243.885 kN mM_c=p_yZ_x/1000=355(687)/1000=243.885\,\mathrm{kN\,m}
M/Mc=103.9926/243.885=0.4264M/M_c=103.9926/243.885=0.4264

PASS

Even the maximum shear is below 0.6Vc, so the low-shear moment resistance applies throughout.

For serviceability use unfactored imposed load only, E = 205,000 N/mm², I in mm⁴ and span in mm. Do not include the ULS factors or dead load in this course deflection limit.

PQ=qkbL1/2=3(2)(6)/2=18 kNP_Q=q_kbL_1/2=3(2)(6)/2=18\,\mathrm{kN}
δ2=PQL2348EI2=18(1000)(4000)348(205000)(12070×104)=0.969952 mm\delta_2=\frac{P_QL_2^3}{48EI_2}=\frac{18(1000)(4000)^3}{48(205000)(12070\times10^4)}=0.969952\,\mathrm{mm}
δlim=L/360=4000/360=11.111111 mm\delta_{lim}=L/360=4000/360=11.111111\,\mathrm{mm}

PASS

Compact exam answer — key result lines
Mc=pyZx/1000=355(687)/1000=243.885 kN mM_c=p_yZ_x/1000=355(687)/1000=243.885\,\mathrm{kN\,m}
M/Mc=103.9926/243.885=0.4264M/M_c=103.9926/243.885=0.4264
PQ=qkbL1/2=3(2)(6)/2=18 kNP_Q=q_kbL_1/2=3(2)(6)/2=18\,\mathrm{kN}
δ2=PQL2348EI2=18(1000)(4000)348(205000)(12070×104)=0.969952 mm\delta_2=\frac{P_QL_2^3}{48EI_2}=\frac{18(1000)(4000)^3}{48(205000)(12070\times10^4)}=0.969952\,\mathrm{mm}
δlim=L/360=4000/360=11.111111 mm\delta_{lim}=L/360=4000/360=11.111111\,\mathrm{mm}

PASS

Short theory: corrosion [4 marks]

  1. Prepare the surface and apply a protective paint/coating system: remove rust, scale and contaminants first so the barrier adheres; renew damaged coating.
  2. Hot-dip galvanising: a zinc layer forms a barrier and provides sacrificial protection at small damaged areas.
  3. Detail to shed water: avoid water traps and crevices; provide drainage/ventilation and access to exposed surfaces.
  4. Inspect and maintain: find corrosion early, clean and repair the protective system before significant steel loss occurs.

Four distinct measures are required. Do not list four paint colours as four methods.

Compact exam answer — key result lines
  1. Prepare the surface and apply a protective paint/coating system: remove rust, scale and contaminants first so the barrier adheres; renew damaged coating.
  2. Hot-dip galvanising: a zinc layer forms a barrier and provides sacrificial protection at small damaged areas.
  3. Detail to shed water: avoid water traps and crevices; provide drainage/ventilation and access to exposed surfaces.
  4. Inspect and maintain: find corrosion early, clean and repair the protective system before significant steel loss occurs.

Four distinct measures are required. Do not list four paint colours as four methods.

Reusable exam procedure and mistakes

  1. Trace the slab arrows and count reactions before doing arithmetic.
  2. Use each member’s exact table row. Class 2 is not Class 1, but both allow capped plastic bending.
  3. Never factor an already factored reaction twice; never include beam dead weight in imposed-load deflection.

Independent practice — invented variant

Invented variant: imposed load rises by 20%, with dead load unchanged. What changes?

Hint

Separate permanent and imposed terms before changing a load.

Reveal answer

Multiply imposed-only deflections by 1.2. Rebuild ULS load as 1.4G + 1.6(1.2Q); do not multiply the total ULS action by 1.2. Section capacities and classes stay unchanged.