Steelwork · Exam learning

2014–2019 · Reference answers

2018-05-02 — connection answers

All connection subparts from this paper, including the specified checks and source qualifications.

Independent teaching answer, not an official solution or marking scheme. Printed marks are retained. Read the source conditions beside each result.

Recognise the connection model

Units: 1 kN = 1,000 N; 1 m = 1,000 mm; 1 cm³ = 1,000 mm³; 1 cm⁴ = 10,000 mm⁴. A demand is the load effect; a resistance is what the member can carry. Compare matching units.

A splice transfers axial force through stages. A side-plate bracket creates in-plane torsion. An end-plate bracket creates bolt tension. Identify which picture applies before selecting a formula.

Bolt shear [2 marks]

Given main plate 26 mm, two covers each 16 mm, Grade 8.8 M16 bolts with 18 mm holes. The transverse dimension chain gives main width 130 mm and cover width 130 mm. Count 6 bolts on ONE side of the butt. The other side is in series and does not double the transferable force.

Source: LectureNotes/Ch2_Connection.pdf · p.3, p.4, p.5, p.9, p.10
Source: LectureNotes/CON4334-Data File-20260730.pdf · p.1, p.4

Grade 8.8: shear strength ps = 375, bolt bearing pbb = 1000, ultimate bolt strength Ub = 800 N/mm². S355 plate: pbs = 550, Us = 510 N/mm², Ke = 1.1. Use threaded stress area As for the conservative shear plane, nominal d for bearing, and hole diameter d0 for material removed.

Simple explanation — open only if needed

The force must cross the left bolt group, travel through the covers, then cross the right group. The weakest stage limits the whole splice, like the weakest link in a chain.

This checks the requested resistance modes. Check edge preparation and ordinary minimum pitch separately; a bearing pass alone does not prove all detailing.

Ps,plane=Asps/1000=157(375)/1000=58.875 kNP_{s,plane}=A_sp_s/1000=157(375)/1000=58.875\,\mathrm{kN}
Ps,bolt=2(58.875)=117.75 kN,Rs=6(2)(58.875)=706.5 kNP_{s,bolt}=2(58.875)=117.75\,\mathrm{kN},\quad R_s=6(2)(58.875)=706.5\,\mathrm{kN}

Each bolt has two shear planes, one at each cover/main interface.

Compact exam answer — key result lines
Ps,plane=Asps/1000=157(375)/1000=58.875 kNP_{s,plane}=A_sp_s/1000=157(375)/1000=58.875\,\mathrm{kN}
Ps,bolt=2(58.875)=117.75 kN,Rs=6(2)(58.875)=706.5 kNP_{s,bolt}=2(58.875)=117.75\,\mathrm{kN},\quad R_s=6(2)(58.875)=706.5\,\mathrm{kN}

Each bolt has two shear planes, one at each cover/main interface.

Bolt bearing [2 marks]

tbearing=min⁡(26,2(16))=26 mmt_{bearing}=\min(26,2(16))=26\,\mathrm{mm}
Pbb=dtbearingpbb/1000=16(26)(1000)/1000=416 kN/boltP_{bb}=dt_{bearing}p_{bb}/1000=16(26)(1000)/1000=416\,\mathrm{kN/bolt}
Rbb=6(416)=2496 kNR_{bb}=6(416)=2496\,\mathrm{kN}
Compact exam answer — key result lines
tbearing=min⁡(26,2(16))=26 mmt_{bearing}=\min(26,2(16))=26\,\mathrm{mm}
Pbb=dtbearingpbb/1000=16(26)(1000)/1000=416 kN/boltP_{bb}=dt_{bearing}p_{bb}/1000=16(26)(1000)/1000=416\,\mathrm{kN/bolt}
Rbb=6(416)=2496 kNR_{bb}=6(416)=2496\,\mathrm{kN}

Plate bearing [7 marks]

Main plate

Rbs=min⁡(dtpbs,0.5etpbs,1.5lctUs,2dtUb)/1000R_{bs}=\min(dt p_{bs},0.5etp_{bs},1.5l_ctU_s,2dtU_b)/1000
lc=p−d0=60−18=42 mml_c=p-d_0=60-18=42\,\mathrm{mm}
Rbs=min⁡(16(26)(550),0.5(35)(26)(550),1.5(42)(26)(510),2(16)(26)(800))/1000R_{bs}=\min(16(26)(550),0.5(35)(26)(550),1.5(42)(26)(510),2(16)(26)(800))/1000
Rbs=min⁡(228.8,250.25,835.38,665.6)=228.8 kN/boltR_{bs}=\min(228.8,250.25,835.38,665.6)=228.8\,\mathrm{kN/bolt}

Each cover plate

Rbs=min⁡(dtpbs,0.5etpbs,1.5lctUs,2dtUb)/1000R_{bs}=\min(dt p_{bs},0.5etp_{bs},1.5l_ctU_s,2dtU_b)/1000
lc=p−d0=60−18=42 mml_c=p-d_0=60-18=42\,\mathrm{mm}
Rbs=min⁡(16(16)(550),0.5(35)(16)(550),1.5(42)(16)(510),2(16)(16)(800))/1000R_{bs}=\min(16(16)(550),0.5(35)(16)(550),1.5(42)(16)(510),2(16)(16)(800))/1000
Rbs=min⁡(140.8,154,514.08,409.6)=140.8 kN/boltR_{bs}=\min(140.8,154,514.08,409.6)=140.8\,\mathrm{kN/bolt}
Rmain,bearing=6(228.8)=1372.8 kN,Rcovers,bearing=2(6)(140.8)=1689.6 kNR_{main,bearing}=6(228.8)=1372.8\,\mathrm{kN},\quad R_{covers,bearing}=2(6)(140.8)=1689.6\,\mathrm{kN}
Rmain,end(em)=6(0.5)em(26)(550)/1000=42.9em kNR_{main,end}(e_m)=6(0.5)e_m(26)(550)/1000=42.9e_m\,\mathrm{kN}

Apply this variable end-distance bound in addition to the other main-plate bearing limits. The drawing is not to scale.

Compact exam answer — key result lines
lc=p−d0=60−18=42 mml_c=p-d_0=60-18=42\,\mathrm{mm}
Rbs=min⁡(16(16)(550),0.5(35)(16)(550),1.5(42)(16)(510),2(16)(16)(800))/1000R_{bs}=\min(16(16)(550),0.5(35)(16)(550),1.5(42)(16)(510),2(16)(16)(800))/1000
Rbs=min⁡(140.8,154,514.08,409.6)=140.8 kN/boltR_{bs}=\min(140.8,154,514.08,409.6)=140.8\,\mathrm{kN/bolt}
Rmain,bearing=6(228.8)=1372.8 kN,Rcovers,bearing=2(6)(140.8)=1689.6 kNR_{main,bearing}=6(228.8)=1372.8\,\mathrm{kN},\quad R_{covers,bearing}=2(6)(140.8)=1689.6\,\mathrm{kN}
Rmain,end(em)=6(0.5)em(26)(550)/1000=42.9em kNR_{main,end}(e_m)=6(0.5)e_m(26)(550)/1000=42.9e_m\,\mathrm{kN}

Apply this variable end-distance bound in addition to the other main-plate bearing limits. The drawing is not to scale.

Plate tension [5 marks]

Main plate, two holes across the critical transverse section.

Ag=bt=130(26)=3380 mm2,An=(b−2d0)t=(130−2(18))(26)=2444 mm2A_g=bt=130(26)=3380\,\mathrm{mm^2},\quad A_n=(b-2d_0)t=(130-2(18))(26)=2444\,\mathrm{mm^2}
Ae=min⁡(Ag,KeAn)=min⁡(3380,1.1(2444))=2688.4 mm2A_e=\min(A_g,K_eA_n)=\min(3380,1.1(2444))=2688.4\,\mathrm{mm^2}
Pt=pyAe/1000=345(2688.4)/1000=927.498 kNP_t=p_yA_e/1000=345(2688.4)/1000=927.498\,\mathrm{kN}

Each cover plate: use its own width and thickness.

Ag=bt=130(16)=2080 mm2,An=(b−2d0)t=(130−2(18))(16)=1504 mm2A_g=bt=130(16)=2080\,\mathrm{mm^2},\quad A_n=(b-2d_0)t=(130-2(18))(16)=1504\,\mathrm{mm^2}
Ae=min⁡(Ag,KeAn)=min⁡(2080,1.1(1504))=1654.4 mm2A_e=\min(A_g,K_eA_n)=\min(2080,1.1(1504))=1654.4\,\mathrm{mm^2}
Pt=pyAe/1000=355(1654.4)/1000=587.312 kNP_t=p_yA_e/1000=355(1654.4)/1000=587.312\,\mathrm{kN}
Pt,covers=2(587.312)=1174.624 kNP_{t,covers}=2(587.312)=1174.624\,\mathrm{kN}
Rsplice=min⁡(706.5,2496,1372.8,1689.6,927.498,1174.624)=706.5 kNR_{splice}=\min(706.5,2496,1372.8,1689.6,927.498,1174.624)=706.5\,\mathrm{kN}
P=900 kN,P/Rsplice=1.273885P=900\,\mathrm{kN},\quad P/R_{splice}=1.273885

FAIL

Compact exam answer — key result lines
Ae=min⁡(Ag,KeAn)=min⁡(2080,1.1(1504))=1654.4 mm2A_e=\min(A_g,K_eA_n)=\min(2080,1.1(1504))=1654.4\,\mathrm{mm^2}
Pt=pyAe/1000=355(1654.4)/1000=587.312 kNP_t=p_yA_e/1000=355(1654.4)/1000=587.312\,\mathrm{kN}
Pt,covers=2(587.312)=1174.624 kNP_{t,covers}=2(587.312)=1174.624\,\mathrm{kN}
Rsplice=min⁡(706.5,2496,1372.8,1689.6,927.498,1174.624)=706.5 kNR_{splice}=\min(706.5,2496,1372.8,1689.6,927.498,1174.624)=706.5\,\mathrm{kN}
P=900 kN,P/Rsplice=1.273885P=900\,\mathrm{kN},\quad P/R_{splice}=1.273885

FAIL

Eccentric weld size [14 marks]

Pu=1.4G+1.6Q=1.4(90)+1.6(130)=334 kNP_u=1.4G+1.6Q=1.4(90)+1.6(130)=334\,\mathrm{kN}
Source: LectureNotes/Ch2_Connection.pdf · p.31, p.33, p.40

The original rectangle is 260 mm wide and 360 mm high. The printed 180 mm eccentricity starts at the dashed centroid, not the rectangle edge. DL and LL are factored once.

Pgroup=334/1=334 kN,M=Pgroupe=334(180)=60120 kN mmP_{group}=334/1=334\,\mathrm{kN},\quad M=P_{group}e=334(180)=60120\,\mathrm{kN\,mm}

Model the continuous effective weld centreline. Its line inertia has units mm³, because integration is over length rather than plate area. At the critical corner, direct vertical shear adds to the vertical torsional component. Horizontal and vertical components combine by Pythagoras.

Lw=2(260+360)=1240 mmL_w=2(260+360)=1240\,\mathrm{mm}
Ix,line=H3/6+BH2/2=3603/6+260(3602)/2=24624000 mm3I_{x,line}=H^3/6+BH^2/2=360^3/6+260(360^2)/2=24624000\,\mathrm{mm^3}
Iy,line=B3/6+HB2/2=2603/6+360(2602)/2=15097333.333333 mm3I_{y,line}=B^3/6+HB^2/2=260^3/6+360(260^2)/2=15097333.333333\,\mathrm{mm^3}
J=Ix+Iy=39721333.333333 mm3J=I_x+I_y=39721333.333333\,\mathrm{mm^3}
qx=M(H/2)J=0.272438 kN/mmq_x=\frac{M(H/2)}{J}=0.272438\,\mathrm{kN/mm}
qy=PLw+M(B/2)J=0.269355+0.196761=0.466116 kN/mmq_y=\frac{P}{L_w}+\frac{M(B/2)}{J}=0.269355+0.196761=0.466116\,\mathrm{kN/mm}
qmax=0.2724382+0.4661162=0.539895 kN/mmq_{max}=\sqrt{0.272438^2+0.466116^2}=0.539895\,\mathrm{kN/mm}
s≥1000qmax0.7pw=1000(0.539895)0.7(250)=3.085112 mms\ge\frac{1000q_{max}}{0.7p_w}=\frac{1000(0.539895)}{0.7(250)}=3.085112\,\mathrm{mm}
strial=6 mm,qRd=0.7(6)(250)/1000=1.05 kN/mms_{trial}=6\,\mathrm{mm},\quad q_{Rd}=0.7(6)(250)/1000=1.05\,\mathrm{kN/mm}
Compact exam answer — key result lines
qx=M(H/2)J=0.272438 kN/mmq_x=\frac{M(H/2)}{J}=0.272438\,\mathrm{kN/mm}
qy=PLw+M(B/2)J=0.269355+0.196761=0.466116 kN/mmq_y=\frac{P}{L_w}+\frac{M(B/2)}{J}=0.269355+0.196761=0.466116\,\mathrm{kN/mm}
qmax=0.2724382+0.4661162=0.539895 kN/mmq_{max}=\sqrt{0.272438^2+0.466116^2}=0.539895\,\mathrm{kN/mm}
s≥1000qmax0.7pw=1000(0.539895)0.7(250)=3.085112 mms\ge\frac{1000q_{max}}{0.7p_w}=\frac{1000(0.539895)}{0.7(250)}=3.085112\,\mathrm{mm}
strial=6 mm,qRd=0.7(6)(250)/1000=1.05 kN/mms_{trial}=6\,\mathrm{mm},\quad q_{Rd}=0.7(6)(250)/1000=1.05\,\mathrm{kN/mm}

Model the continuous effective weld centreline. Its line inertia has units mm³, because integration is over length rather than plate area. At the critical corner, direct vertical shear adds to the vertical torsional component. Horizontal and vertical components combine by Pythagoras.

Reusable procedure and common errors

  1. Draw the load-transfer stages. Count bolts and shear planes for one stage, then compare all failure modes.
  2. Resolve eccentric forces as vectors. Never add perpendicular components arithmetically.
  3. Use effective weld length and check size limits after strength; “strong enough” does not fix an impossible detail.

Independent practice — invented variant

Invented variant: all applied loads are 10% larger but geometry is unchanged. What scales, and what does not?

Hint

Isolate one load-transfer stage, then distinguish demand from fixed resistance.

Reveal answer

For these linear elastic models, bolt forces and weld force per unit length rise 10%; required strength-only weld throat also rises 10%. Bolt areas, section capacities, effective lengths of already specified welds and detailing limits stay unchanged. Recheck every utilisation.