STEELWORK / CON4334
Reference

Companion slides and quick-reference notes

Diagrams, explanations and answers are presented in reading order. No playback or response is required.
All answers shownChinese–English terminology

These are teaching notes for every slide in the four companion presentations.

Each original slide remains readable locally.

The linked chapter supplies the full derivation and worked applications; corrections to compressed slide statements are explicit.

PPT/Structural Steelwork Design L1.pptx · slide 1: Introduction: what you are learning

Make the next decision from the known conditions

Read the specific task below and identify the quantity or explanation it asks for.

ConditionsModelCalculationCheckA changed condition can change the method.
The sequence links source conditions, a physical model, a calculation and a checked conclusion. Each link needs the previous one.

Prediction, then explanation. Changing a load value may preserve the method. Changing the support or failure mechanism can require a different method.

Separate given, lookup, calculated and assumed values. State why the model applies. Keep necessary intermediate steps and units beside the equations.

A conditional answer states the exact condition required for its conclusion. It does not fill missing data with a guess.

Scope. A repeated result is not an independent verification. Use equilibrium, dimensions, a reverse substitution or an appropriate limiting case.

Check and takeaway. The explanation and answer are shown together in this edition. No response, score or completed interaction is needed to continue.

Apply the reasoning to this section’s data and conditions

A design answer compares a demand caused by loads with a resistance supplied by steel.

First calculate the loads and forces; then check the chosen component.

A failure of any required check means the proposal needs revision.

Study the full explanation and applications.

Original slide 1: Introduction: what you are learning. No dimensions are inferred from slide scale.

Original slide 1, introduction: what you will learn.

The title is Structural Steelwork Design; Chapter 1 covers foundations, steel metallurgy and HK Code 2011.

The module is CON4334 Civil Engineering and the lecturer is credited as King Lai.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsFollow the calculation sequence1 concept

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Locate the load, supports, connection geometry and any stated assumptions.
  2. Keep given values, table lookups and calculated values distinct; reconcile their units.
  3. The calculation player steps through the existing expressions in their original order.
  4. Compare demand with resistance or the relevant limit.

    Keep missing inputs and conditional conclusions explicit.

PPT/Structural Steelwork Design L1.pptx · slide 2: The course roadmap

Separate stiffness, strength and ductility

Two steels may resist similar elastic deformation but start permanent deformation at different stresses.

σεYieldESchematic • not a measured material curve
On the stress–strain sketch, the initial slope represents stiffness. The yield level marks the start of substantial permanent strain.

Prediction, then explanation. Raising the yield level alone need not change the initial slope. The same elastic load can therefore give similar deformation.

Stress is force per area. Strain is extension divided by original length. Their elastic ratio defines Young’s modulus.

σ=Eε\sigma=E\varepsilon

σ is stress in N/mm²; ε is dimensionless strain; E is Young’s modulus in N/mm².

Scope. Use this linear relationship only in its elastic range. Ductility concerns deformation before fracture, not the value of E.

Check and takeaway. When elastic load is removed, elastic strain recovers. Yielded steel can retain strain after unloading.

Repeated loading can grow a crack

A detail experiences many load cycles. A single static resistance check does not describe its fatigue behaviour.

CyclesσmaxσminRepeated stress change → possible crack growth
The upper and lower stress levels define a stress range. The crack sketch shows successive possible growth fronts.

Prediction, then explanation. More cycles or a larger stress range can increase fatigue damage. Remaining below yield is not a universal fatigue guarantee.

A local notch or weld detail concentrates stress. Repeated changes can extend a crack from that region.

Δσ=σmax−σmin\Delta\sigma=\sigma_{max}-\sigma_{min}

Δσ is stress range in N/mm². Maximum and minimum stresses must refer to the same location and stress component.

Scope. The sketch is a mechanism explanation, not a life prediction. Fatigue design requires the applicable detail category and load history.

Check and takeaway. A static pass does not remove the need for a fatigue check when repeated loading is relevant.

Interrupt the corrosion process

Steel exposed to moisture and oxygen can lose material. Explain what each protection system does.

SteelCoatingExposed gapBarrier intact / barrier interrupted
The coating surrounds the steel. A break in the coating exposes a local path to the steel surface.

Prediction, then explanation. If a barrier coating is damaged, the exposed region can corrode. Zinc can also provide sacrificial protection where conditions permit.

Paint works mainly as a barrier. Galvanizing adds a zinc layer with barrier and sacrificial effects. Surface preparation affects performance.

No universal coating thickness or life follows from this mechanism sketch.

Scope. Weathering steel still needs suitable exposure and detailing. A protection label does not replace inspection or maintenance.

Check and takeaway. The useful comparison is the protection mechanism, exposure and maintenance need. Do not describe all coatings as identical barriers.

Apply the reasoning to this section’s data and conditions

Learn foundations before connections, beams and columns.

The same equilibrium equations recur: vertical forces balance, horizontal forces balance, and moments balance.

The shape and restraints decide which resistance checks are needed.

Study the full explanation and applications.

Original slide 2: The course roadmap. No dimensions are inferred from slide scale.

Original slide 2, Learning Roadmap.

The five topics are: materials and metallurgy (composition, alloys, fatigue, corrosion and fire protection); steel sections (hot-rolled UB/UC, built-up and cold-formed); limit state design (ULS/SLS and partial safety factors); analysis and initial imperfections (P–Δ effects and 0.5% notional horizontal forces, NHF); and classification/deflection limits (plastic through slender classes, SLS Table 5.1).

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsFollow the calculation sequence12 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Locate the load, supports, connection geometry and any stated assumptions.
  2. Keep given values, table lookups and calculated values distinct; reconcile their units.
  3. The calculation player steps through the existing expressions in their original order.
  4. Compare demand with resistance or the relevant limit.

    Keep missing inputs and conditional conclusions explicit.

PPT/Structural Steelwork Design L1.pptx · slide 3: Steel behaviour and protection

Use the same mechanism: Separate stiffness, strength and ductility. Raising the yield level alone need not change the initial slope. The same elastic load can therefore give similar deformation.

Use the same mechanism: Repeated loading can grow a crack. More cycles or a larger stress range can increase fatigue damage. Remaining below yield is not a universal fatigue guarantee.

Use the same mechanism: Interrupt the corrosion process. If a barrier coating is damaged, the exposed region can corrode. Zinc can also provide sacrificial protection where conditions permit.

Apply the reasoning to this section’s data and conditions

The slide describes steel as mostly iron, with controlled carbon and manganese.

Carbon raises strength but can reduce ductility and weldability.

Fatigue is repeated-load crack growth; corrosion removes material; heat reduces stiffness and strength.

For an exam explanation, link each protection method to the damage mechanism it prevents.

Study the full explanation and applications.

Original slide 3: Steel behaviour and protection. No dimensions are inferred from slide scale.

Original slide 3, Material & Metallurgy.

The left column lists composition: approximately 98% iron, up to 0.25% carbon, up to 1.6% manganese, plus silicon, phosphorus and sulphur.

Higher carbon increases strength but reduces ductility and weldability.

The right column says to avoid stress concentrations and abrupt section changes for fatigue; corrosion protection includes galvanising, weathering steel and cathodic protection; fire protection uses solid, hollow or profile casing.

The percentages are the slide's statements, not complete material specifications for every grade.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsElasticity, yielding and ductility4 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Stress is force divided by area.

    Strain measures change in length relative to original length.

  2. Before yielding, stress is approximately .

    E controls the elastic slope.

  3. Further strain includes permanent deformation.

    Higher yield strength does not by itself increase E.

  4. Strength, stiffness and ductility answer different questions.

    This schematic is not a measured stress–strain curve.

PPT/Structural Steelwork Design L1.pptx · slide 4: Recognise the section

Use the property for the physical question

A section table contains several numbers. Choose the property that matches the calculation and bending axis.

Read the three labels beside the I-section: I describes geometric stiffness, Z elastic section modulus and S plastic section modulus.
Read the three labels beside the I-section: I describes geometric stiffness, Z elastic section modulus and S plastic section modulus.

Prediction, then explanation. Moving equal area away from an axis increases I about that axis. It does not increase total area.

Each small area contributes its area multiplied by squared distance. Sum those contributions to obtain I.

I=∫y2 dA,r=I/AI=\int y^2\,dA,\qquad r=\sqrt{I/A}

I is second moment of area in mm⁴. y is distance from the chosen axis in mm. A is area in mm². r is radius of gyration in mm.

Scope. Z is elastic section modulus; S is plastic section modulus in this course. Neither is interchangeable with I.

Check and takeaway. A nominal section designation is a row identifier. Use the actual dimensions and units in that exact row.

Apply the reasoning to this section’s data and conditions

An I or H section has two flanges and a web; angles and channels are open, unsymmetrical shapes.

Rolled means formed hot at a mill.

Built-up means plates or sections joined into a member.

Identify the section family before choosing dimensions, axes or buckling curves.

Study the full explanation and applications.

Original slide 4: Recognise the section. No dimensions are inferred from slide scale.

Original slide 4, Steel Section Types.

Hot-rolled UBs mainly resist major-axis bending; UCs accommodate larger axial compression.

CHS/SHS/RHS hollow sections are efficient in compression and torsion.

Built-up and compound sections include plate girders, crane girders, and battened/laced members.

Cold-formed thin-walled Z, sigma and lipped channel sections can serve as purlins.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsExplore section geometry and axes1 concept

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The flanges are the wide plates.

    The web connects them.

    Rotate the I-section to see both.

  2. The same section has different stiffness and resistance about its two principal axes.
  3. I controls elastic curvature.

    is elastic section modulus.

    Plastic modulus S comes from plastic stress blocks.

  4. Nominal section labels are not every actual dimension.

    Keep the row, axis and units together.

PPT/Structural Steelwork Design L1.pptx · slide 5: ULS versus SLS

Ask two separate design questions

Decide whether the check concerns failure or unacceptable behaviour during use.

The strength branch compares demand with resistance. The service branch compares displacement with its specified limit.
The strength branch compares demand with resistance. The service branch compares displacement with its specified limit.

Prediction, then explanation. A larger section may improve both results, but a pass on one branch does not prove a pass on the other.

ULS addresses relevant strength and stability failure modes. SLS addresses specified service conditions such as deflection.

demand≤resistance,δ≤δlimit\text{demand}\le\text{resistance},\qquad\delta\le\delta_{limit}

δ is the calculated displacement; δlimit is the permitted displacement. Both must use the same length unit.

Scope. Use each check’s own load combination and limit. A strength load factor does not change the physical stiffness.

Check and takeaway. Write separate conclusions for strength, stability and serviceability where requested. A single unexplained “safe” hides those distinctions.

Apply the reasoning to this section’s data and conditions

ULS checks strength and stability using the prescribed factored load combination.

SLS checks usable behaviour such as deflection.

Do not carry the ULS load into an imposed-load-only deflection check.

G is permanent load, Q imposed load and W wind action.

Study the full explanation and applications.

Original slide 5: ULS versus SLS. No dimensions are inferred from slide scale.

Original slide 5, Limit State Design Philosophy.

The left column describes ULS protection against collapse, yielding and fracture; γf>1.0 denotes the partial load factor, and γm the material factor reducing nominal strength.

The right column describes everyday serviceability, controlling excessive deflection, floor vibration and dynamic sway.

It lists unfactored service loads γf=1.0.

Factors must still be selected for the actual combination and course rules.

The left-column summary is not a universal rule for all favourable/unfavourable loads.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsTwo different design questions1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. ULS compares factored actions with the applicable resistance to yielding, rupture or instability.
  2. SLS checks movement, vibration or another specified use requirement.
  3. A beam can be strong enough but deflect too much.

    The two checks need their own loads and denominators.

  4. A resistance pass cannot stand in for a serviceability pass.

    Complete all requested checks.

PPT/Structural Steelwork Design L1.pptx · slide 6: Choose a load combination

Keep load categories separate

A floor carries permanent material and changing occupancy loads. Find the design load for the stated check.

The two boxes show G and Q with their separate factors. The plus sign joins their factored values.
The two boxes show G and Q with their separate factors. The plus sign joins their factored values.

Prediction, then explanation. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

First convert mass to weight where required. Next collect G and Q in compatible units. Apply the combination specified by the course problem.

Wu=1.4G+1.6QW_u=1.4G+1.6Q

G is characteristic dead load; Q is characteristic imposed load. Wu is the design load for this course gravity combination.

Scope. This combination is not universal. Use the specified service load for deflection and the stated factors for other standards or cases.

Check and takeaway. Illustration: G = 10 kN and Q = 5 kN give 22 kN. Factoring their sum by one guessed factor loses the distinction.

Apply the reasoning to this section’s data and conditions

The slide lists 1.4G+1.6Q, 1.4G+1.4W and 1.2G+1.2Q+1.2W.

These are different cases, not extra multipliers applied one after another.

Choose the relevant adverse combination and consider whether an action is beneficial.

For example, G=4 and Q=3kNm2 gives 1.4×4+1.6×3=10.4kNm2.

Study the full explanation and applications.

Original slide 6: Choose a load combination. No dimensions are inferred from slide scale.

Original slide 6, Factored Load Combinations (HK Code 2011).

The three source expressions are:1.4dead load+1.6imposed load; 1.4dead load+1.4wind load; 1.2dead load+1.2imposed load+1.2wind load.

Dead, imposed and wind loads correspond respectively to G/Q/W above.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsFrom characteristic to design load1 concept · 3 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. G is permanent load; Q is imposed load.

    A surface load and a line load also have different units.

  2. This illustration uses the course gravity case .

    Other combinations in the original text retain their own factors.

  3. For illustrative , the separate load contributions show what changes when Q increases.
  4. Do not carry this ULS total automatically into deflection.

    Follow the stated SLS load case.

PPT/Structural Steelwork Design L1.pptx · slide 7: Choose the analysis model

Restraints define the analysis model

Choose an analysis model that represents the actual joints, restraints and possible sway.

Braced pathPossible sway
The joint symbol describes permitted rotation. The frame arrows describe possible sideways movement. These are separate observations.

Prediction, then explanation. A joint that permits beam rotation does not automatically remove all column moment. Eccentric reactions may still bend the column.

First identify the joint behaviour. Next identify how horizontal forces reach the foundations. Then assess sway sensitivity using the course criterion.

Simple, continuous and semi-continuous construction describe joint modelling. Sway classification describes overall frame response.

Scope. The schematic does not establish restraint stiffness or a stability threshold. Use the stated data and classification rules.

Check and takeaway. An ideal straight frame may still require notional horizontal forces to represent imperfections under the applicable method.

Compression acts on the displaced shape

A compressed member moves away from its initial load line. Explain why the bending moment can increase.

The dashed line labelled Original marks the initial position. The tilted member creates the extra horizontal lever arm shown below.
The dashed line labelled Original marks the initial position. The tilted member creates the extra horizontal lever arm shown below.

Prediction, then explanation. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Force acting through an offset forms a moment. Second-order analysis includes that changed geometry in equilibrium.

Madditional=PΔorPδM_{additional}=P\Delta\quad\text{or}\quad P\delta

P is axial force. Δ and δ are the relevant perpendicular displacements. Consistent force and length units give moment units.

Scope. Use the amplification or analysis method stated for the frame. Do not amplify an already amplified moment a second time.

Check and takeaway. Zero offset removes this additional moment in the ideal sketch. Real design may still require imperfections and code checks.

Apply the reasoning to this section’s data and conditions

Simple construction treats joints as nominally pinned for global analysis; continuous construction transfers joint moments.

First-order analysis uses the undeformed shape; second-order analysis includes extra moments caused by displacement under axial force.

Do not infer moment fixity from a visually thick line in a sketch.

Study the full explanation and applications.

Original slide 7: Choose the analysis model. No dimensions are inferred from slide scale.

Original slide 7, Methods of Structural Analysis.

Simple design uses pinned connections with cores/bracing resisting lateral loads; continuous design uses rigid moment-resisting connections.

First-order linear-elastic analysis ignores geometric deformation; second-order analysis includes geometric nonlinearity from overall sway P–Δ and member bending P–δ.

The slide identifies HK Code 2011.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsRestraints, sway and imperfections2 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A frame needs a defined path for horizontal force as well as gravity.
  2. Pinned joints alone do not provide frame moment resistance; sway restraint needs a real structural system.
  3. Diagonal bracing carries horizontal action through axial forces.

    This sketch does not assign a numerical frame classification.

  4. Use the specified imperfection/notional-force model and critical-load criteria.

    Avoid counting alternative imperfection models twice.

PPT/Structural Steelwork Design L1.pptx · slide 8: Imperfections and notional forces

Use the same mechanism: Restraints define the analysis model. A joint that permits beam rotation does not automatically remove all column moment. Eccentric reactions may still bend the column.

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Apply the reasoning to this section’s data and conditions

Real members are not perfectly straight or vertical.

The slide uses a nominal frame imperfection 1200 and notional horizontal force 0.005 times vertical load.

For a 2000kN vertical action, that force is 0.005×2000=10kN.

Apply it in the stated analysis case.

It does not replace actual wind automatically.

Member initial bow and frame lean are different imperfections.

Study the full explanation and applications.

Original slide 8: Imperfections and notional forces. No dimensions are inferred from slide scale.

Original slide 8, Initial Imperfections & NHF.

The slide says a structure is not 100% perfectly vertical.

The reference angle for overall inclination is φ=1200rad; NHF acts horizontally and is at least the following fraction of total factored vertical load: 0.5% (0.005).

Initial member bow is represented by e0L.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsRestraints, sway and imperfections2 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A frame needs a defined path for horizontal force as well as gravity.
  2. Pinned joints alone do not provide frame moment resistance; sway restraint needs a real structural system.
  3. Diagonal bracing carries horizontal action through axial forces.

    This sketch does not assign a numerical frame classification.

  4. Use the specified imperfection/notional-force model and critical-load criteria.

    Avoid counting alternative imperfection models twice.

PPT/Structural Steelwork Design L1.pptx · slide 9: Serviceability limits

A safe beam can still sag too far

Check whether the beam displacement exceeds the permitted service limit.

The straight beam marks the unloaded position. The curved line and vertical arrow show downward displacement, exaggerated for explanation.
The straight beam marks the unloaded position. The curved line and vertical arrow show downward displacement, exaggerated for explanation.

Prediction, then explanation. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.

Load bends each beam segment. The curvature accumulates along the span. Material stiffness E and geometric stiffness I resist that deformation.

δmid=5wL4384EI\delta_{mid}=\frac{5wL^4}{384EI}

Use w in N/mm, L in mm, E in N/mm² and I in mm⁴. The resulting midspan deflection is in mm.

Scope. The formula assumes a prismatic, simply supported, linear-elastic beam with full-span UDL. Use the stated service load and deflection limit.

Check and takeaway. A higher yield grade does not automatically increase E. Passing a strength check therefore does not prove acceptable deflection.

Apply the reasoning to this section’s data and conditions

For imposed-load vertical deflection, use the applicable row: brittle finishes L360, other beams L200, cantilevers L180.

The slide also mentions crane L600 and frame H500.

The full course table states the conditions, so a limit must be selected by function and displacement type.

A span of 7200mm at L360 permits 20mm.

Study the full explanation and applications.

Original slide 9: Serviceability limits. No dimensions are inferred from slide scale.

Original slide 9, SLS Deflection Limits (Table 5.1).

The four rows are: beams supporting plaster/finishes, deflection≤L360; general beams, deflection≤L200; crane girders, deflection≤L600; building-frame sway, sway≤H500.

This reproduces the source summary table; actual uses and load conditions must follow the full table.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsSee stiffness and deflection1 concept · 4 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Use the specified SLS load, span and support arrangement.

    The demonstrator has a full-span UDL.

  2. The loaded beam bends.

    The deformation is exaggerated so its shape can be seen.

  3. For a simply supported full-span UDL, .

    Double L with w, E and I unchanged: δ becomes 16 times as large.

  4. The readout uses , and .

    Select the finish/support-specific limit from the original table.

PPT/Structural Steelwork Design L1.pptx · slide 10: Strength depends on thickness

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Apply the reasoning to this section’s data and conditions

S355 is a grade name, not a promise that every thickness has design strength 355Nmm2.

Read the maximum-thickness row: a 22mm flange falls in the ≤40mm row, giving 345Nmm2.

Then ε=275345=0.892804.

Use the controlling plate thickness for the relevant property check.

Study the full explanation and applications.

Original slide 10: Strength depends on thickness. No dimensions are inferred from slide scale.

Original slide 10, Steel Grades & Design Strength.

The left column lists BS EN grades S275, S355 and S460, with the shorthand py=275,355,460Nmm2.

It also lists GB grades Q235, Q345, Q390 and Q420.

The right column says increasing t reduces py, and gives the width/thickness parameter ε=275py.

The left-column unit has a question-mark-like superscript.

Here it is transcribed as Nmm2 using the strength table from the same course, while retaining the source image.

The left-column shorthand is not a universal lookup value across all thicknesses.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsRead a table without losing the keys1 concept · 4 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Name the required property: material strength, section property, buckling strength or a moment factor.
  2. Keep section size, steel grade, thickness band, curve and axis as separate lookup keys.
  3. , and require different conversion powers.

    Do not use adjacent columns interchangeably.

  4. Use bracketing rows within the same valid column.

    The original page remains the source of all table values.

PPT/Structural Steelwork Design L1.pptx · slide 11: Section classes

Find which plate buckles first

Before using plastic bending resistance, check whether the flange and web can sustain the required stress distribution.

The short waves are local plate buckling. They differ from sideways movement of the whole member.
The short waves are local plate buckling. They differ from sideways movement of the whole member.

Prediction, then explanation. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Calculate the flange and web ratios separately. Compare each with the limits for its stress condition. The worse class governs.

ε=275/py\varepsilon=\sqrt{275/p_y}

py is the design yield strength in N/mm². ε is a dimensionless scale used in the supplied classification limits.

Scope. Pure bending and uniform compression use different web limits. Class 2 allows plastic resistance but not the Class 1 rotation capability.

Check and takeaway. A Class 1 web and Class 2 flange give a Class 2 section. Do not average the class numbers.

Apply the reasoning to this section’s data and conditions

Class 1 permits a plastic hinge with rotation.

Class 2 reaches plastic moment with less rotation.

Class 3 uses elastic capacity.

Class 4 requires effective properties.

Check flange and web separately under their actual stress distributions, then take the worse class.

A stocky flange does not make a slender web Class 1.

Study the full explanation and applications.

Original slide 11: Section classes. No dimensions are inferred from slide scale.

Original slide 11, Cross-Section Classification.

Class 1, Plastic: a plastic hinge has sufficient rotation capacity.

Class 2, Compact: the section can reach plastic moment Mp, but local buckling limits rotation.

Class 3, Semi-Compact: the extreme fibre reaches py, but local buckling prevents full plastic moment.

Class 4, Slender: local buckling occurs before yielding.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsWhy thin elements buckle locally1 concept

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The flange outstand and web have different widths, thicknesses and edge support conditions.
  2. A thinner plate can wrinkle locally before the complete member loses stability.
  3. Class 1 allows plastic rotation.

    Class 2 reaches plastic resistance.

    Class 3 reaches elastic resistance.

    Class 4 requires effective properties.

  4. Check every relevant compression element with the supplied limits and stress distribution.

    The deformation shown is qualitative.

PPT/Structural Steelwork Design L1.pptx · slide 12: Turn discussion into a self-test

Vertical bending can trigger sideways motion

A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.

The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.
The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.

Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.

λ=LE/ry,Mb=pbSx  (Class 1/2),mLTMmax≤Mb\lambda=L_E/r_y,\qquad M_b=p_bS_x\;\text{(Class 1/2)},\qquad m_{LT}M_{max}\le M_b

LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.

Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.

Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.

Check buckling about both axes

Determine which buckling direction limits the compressed member.

Compare the outlines labelled Straight and Bowed. The dashed line beside Bowed marks its original straight reference.
Compare the outlines labelled Straight and Bowed. The dashed line beside Bowed marks its original straight reference.

Prediction, then explanation. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Calculate slenderness about each axis. Select each axis’s curve from section type and thickness. Then obtain and compare the two compressive resistances.

λx=LEx/rx,λy=LEy/ry,Pc=pcAg\lambda_x=L_{Ex}/r_x,\quad\lambda_y=L_{Ey}/r_y,\qquad P_c=p_cA_g

Effective lengths and radii use mm. pc is compressive strength in N/mm²; Ag is gross area in mm²; Pc is in N.

Scope. Do not select the governing axis using radius alone. Effective length and buckling curve can differ. A combined column also needs interaction checks.

Check and takeaway. A short-section yield resistance is not the same as long-member buckling resistance. Keep py and pc distinct.

A bolt diameter is not a hole diameter

Check that bolts fit and leave enough material between holes and plate boundaries.

pdd₀Clear ligament
The inner circle represents bolt diameter d. The outer circle represents hole diameter d₀. Pitch and gauge join hole centres.

Prediction, then explanation. At fixed pitch, a larger hole leaves a shorter clear ligament. Increasing bolt diameter may also increase minimum edge-distance requirements.

Measure pitch along the bolt line and gauge across lines. Distinguish end distance along the load from edge distance across it.

lc=p−d0l_c=p-d_0

lc is clear ligament between holes; p is centre-to-centre pitch; d₀ is hole diameter. All use mm.

Scope. Apply the supplied edge-preparation and minimum/maximum spacing rules. Passing a bearing calculation does not prove the layout passes.

Check and takeaway. For pitch 60 mm and hole diameter 22 mm, the ligament is 38 mm. Using a 20 mm bolt diameter here gives the wrong ligament.

Apply the reasoning to this section’s data and conditions

Three distinctions connect these lessons.

A beam can pass section bending but fail LTB.

A column has a slenderness ratio for each axis.

Bolt diameter differs from hole diameter.

Answers: instability depends on unrestrained length; radii/restraints differ by axis; holes need clearance.

The linked chapters connect each distinction to its diagram and calculation.

Study the full explanation and applications.

Original slide 12: Turn discussion into a self-test. No dimensions are inferred from slide scale.

Original slide 12, Questions & Discussion: no calculation question or dimension is given.

The discussion topics are turned into self-checks above and are not presented as original exam questions.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsA beam bends sideways and twists3 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For the illustrated sagging beam the top flange is compressed.
  2. The unrestrained compression flange can move sideways while the complete cross-section twists.
  3. Only effective restraints divide the member into unbraced segments.

    They do not automatically add vertical supports.

  4. Use the segment effective length, section properties and matching moment factor.

    This is an exaggerated mode shape, not a calculated displacement.

PPT/Joint Connections L2.pptx · slide 1: Joint connections: purpose

Count cuts through each loaded bolt

Find how many shear planes transfer the force through one side of the connection.

The middle plate moves against two cover plates. The two interfaces cut each bolt at two planes.
The middle plate moves against two cover plates. The two interfaces cut each bolt at two planes.

Prediction, then explanation. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Select the area at the actual shear plane. Multiply by bolt shear strength. Count only the bolts and planes in the same transfer stage.

Ps=psAs,Pgroup=nbnsPsP_s=p_sA_s,\qquad P_{group}=n_b n_s P_s

ps is bolt shear strength in N/mm²; As is the appropriate area in mm². nb counts bolts; ns counts equally loaded shear planes.

Scope. Use the thread area when threads cross the plane as required. Check bearing, plate failure and detailing separately.

Check and takeaway. Both halves of a butt splice carry the full transmitted force in sequence. Counting both halves together would double the apparent resistance.

The weld resists through its throat

Convert a visible fillet leg into resistance per effective length.

The two outer sides are the legs. The shorter perpendicular line through the ideal triangle is the throat.
The two outer sides are the legs. The shorter perpendicular line through the ideal triangle is the throat.

Prediction, then explanation. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

For the course right-angle equal-leg fillet, take throat as 0.7 times leg. Multiply throat area per unit length by weld strength.

a=0.7s,qcap=0.7spw/1000a=0.7s,\qquad q_{cap}=0.7sp_w/1000

s and a are leg and throat in mm. pw is weld strength in N/mm². qcap is resistance in kN/mm.

Scope. Use effective length, the correct steel/electrode strength and permitted leg limits. Full-penetration butt welds use a different model.

Check and takeaway. Illustration: a 6 mm leg at 250 N/mm² gives 0.7(6)(250)/1000=1.05 kN/mm0.7(6)(250)/1000=1.05\,\mathrm{kN/mm}.

Apply the reasoning to this section’s data and conditions

A connection transfers forces between members.

Sketch the complete force path before calculating an individual bolt or weld.

A strong fastener cannot rescue a weak connected plate.

Study the full explanation and applications.

Original slide 1: Joint connections: purpose. No dimensions are inferred from slide scale.

Original slide 1: Steelwork Design: Joint Connections; Module CON4334, Chapter 2; Bolted & Welded Connections.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsCount the bolt shear planes3 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Load must cross an interface between the connected plates.
  2. A lap joint gives one shear plane through a bolt.
  3. A symmetric double-cover joint may provide two shear planes.

    Count load-transfer interfaces, not just visible plates.

  4. Use the source’s area and shear strength.

    Then check bearing, plate resistance and detailing separately.

PPT/Joint Connections L2.pptx · slide 2: Bolts and welds

Use the same mechanism: Count cuts through each loaded bolt. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

An eccentric bracket pulls bolts differently

An out-of-plane moment rotates the bracket about the stated pivot. Determine the bolt tension pattern.

The pivot is the compression reference. Bolts farther from it have longer lever arms in the course elastic model.
The pivot is the compression reference. Bolts farther from it have longer lever arms in the course elastic model.

Prediction, then explanation. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Use compatibility to relate tension to distance. Moment equilibrium then determines the proportionality factor.

Ft,i=Myi∑yj2F_{t,i}=\frac{My_i}{\sum y_j^2}

M is moment in kN·mm. yi is distance from the stated pivot in mm. Ft,i is tension in kN.

Scope. Apply only to the stated active bolt set and pivot model. Flexible plates can create prying; use the supplied assumptions and resistance definitions.

Check and takeaway. A bolt’s lever arm is measured from the pivot used in the equation. It is not automatically its distance from the group centroid.

Follow contact pressure into the plate

The bolt may survive shear while the connected plate deforms or tears near the hole.

The labels distinguish bolt diameter d from hole diameter d₀. The arrow at the hole edge shows the bearing contact action.
The labels distinguish bolt diameter d from hole diameter d₀. The arrow at the hole edge shows the bearing contact action.

Prediction, then explanation. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

Calculate every bound required by the supplied rule. The smallest applicable bound limits the connection at that layer.

Pbearing≤pbsdtP_{bearing}\le p_{bs}dt

pbs is the applicable bearing strength in N/mm²; d is nominal bolt diameter in mm; t is plate thickness in mm.

Scope. This diameter term alone is not the complete check. End-distance and clear-ligament limits, bolt bearing and each connected layer also matter.

Check and takeaway. Two covers and one main plate do not necessarily have the same thickness or strength. Compare the actual force share in each layer.

Apply the reasoning to this section’s data and conditions

Bolts transfer force through shear, bearing, tension, or specified friction-grip action.

Welds transfer force through fused metal along an effective throat.

This course’s ordinary-bolt equations do not establish slip resistance for a friction-grip joint.

Study the full explanation and applications.

Original slide 2: Bolts and welds. No dimensions are inferred from slide scale.

Original slide 2, connection fundamentals: bolts and welds.

Their structural purpose is to transfer tension, shear and moment safely between members.

Ordinary clearance bolts are listed as Grades 4.6/8.8; high-strength friction-grip (HSFG) bolts are also listed.

Bolts permit quick, straightforward site assembly without special equipment.

Fillet welds join corners; butt welds join prepared grooves.

Welding offers a neat appearance, compact details and structural continuity.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsCount the bolt shear planes5 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Load must cross an interface between the connected plates.
  2. A lap joint gives one shear plane through a bolt.
  3. A symmetric double-cover joint may provide two shear planes.

    Count load-transfer interfaces, not just visible plates.

  4. Use the source’s area and shear strength.

    Then check bearing, plate resistance and detailing separately.

PPT/Joint Connections L2.pptx · slide 3: Read the bolt layout

Use the same mechanism: A bolt diameter is not a hole diameter. At fixed pitch, a larger hole leaves a shorter clear ligament. Increasing bolt diameter may also increase minimum edge-distance requirements.

Apply the reasoning to this section’s data and conditions

Pitch runs along the force transfer direction; gauge separates lines; end distance is from a hole centre to the end in that direction.

Hole diameter is used in net area, nominal bolt diameter in projected bearing.

Check standard-hole clearance and minimum/maximum spacing before claiming a layout is valid.

Study the full explanation and applications.

Original slide 3: Read the bolt layout. No dimensions are inferred from slide scale.

Original slide 3, hole clearance and layout rules.

Standard holes: if d≤24mm,hole diameter=d+2mm; if d>24mm,hole diameter=d+3mm.

Minimum pitch along the load direction 2.5d; minimum transverse spacing perpendicular to the load 3.0d; maximum spacing min(12t,150mm),t is the thinner plate thickness.

End and edge distances prevent end tear-out and provide sufficient bearing area.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsBolt centres, holes and edges1 concept · 5 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Hole diameter d₀ differs from nominal bolt diameter d.

    Net-section deductions use the specified hole.

  2. Pitch runs along the load direction; gauge measures spacing across rows.
  3. End and edge distances start at the hole centre.

    The remaining ligament starts at the hole boundary.

  4. Minimum spacing, edge distances, grip and plate thickness come from the specified rules, not this scaled illustration.

PPT/Joint Connections L2.pptx · slide 4: Five failure modes

A block leaves along two types of path

A connection can lose a block of plate without a single straight tensile fracture across the full width.

The longitudinal dashed segments are shear paths. The transverse closing segment is a tension path.
The longitudinal dashed segments are shear paths. The transverse closing segment is a tension path.

Prediction, then explanation. Changing the end distance changes the shear-path geometry. Adding plate width elsewhere may not strengthen the controlling block.

Draw the possible block first. Label shear and tension segments. Apply the course deductions and strength terms to their respective areas.

Shear and tension areas use mm². Their strength coefficients refer to different mechanisms and are not interchangeable.

Scope. Do not replace the supplied block-shear expression with the simple net-tension formula. Geometry and deductions depend on the actual path.

Check and takeaway. A complete path must release a block. A dashed line that does not enclose a removable piece is not that failure mechanism.

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Use the same mechanism: Count cuts through each loaded bolt. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Apply the reasoning to this section’s data and conditions

Inspect bolt shear, bolt tension where present, bearing of the bolt/connected part, tensile rupture of the net section and block shear.

For each mode draw what separates or deforms.

Capacity is the smallest applicable resistance along the force path, not the sum of unrelated failure resistances.

Study the full explanation and applications.

Original slide 4: Five failure modes. No dimensions are inferred from slide scale.

Original slide 4, five core failure modes of bolted connections. (1) Bolt-shank shear: per plane in single/double shear, Ps=psAs; (2) local bearing at the plate/bolt hole: the slide gives Pbb=dtppbb; (3) net-section tensile rupture of the connected plate: the slide gives Ae=Kean, still subject to rules including the gross-area cap; (4) end shear tear-out when end distance is insufficient; (5) block shear along the bolt rows with tension across the end line.

This five-mode source list uses a different grouping from the comprehensive checklist above.

Bolt tension must still be checked separately whenever tension exists.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsSeparate the block-shear paths5 concepts · 3 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A block containing the connection can detach from the surrounding plate.
  2. The paths parallel to the applied force carry shear.
  3. The closing path across the end of the block carries tension.
  4. Use the specified gross/net deductions and resistance expression.

    This is different from a single straight net-section fracture.

PPT/Joint Connections L2.pptx · slide 5: Weld types and inspection

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Penetration changes the resisting section

Determine whether the weld develops the full joint thickness or only an effective part.

FullPartialroot
The full-penetration sketch joins the entire thickness. The partial-penetration sketch leaves a root region outside the effective weld.

Prediction, then explanation. Keeping the same plate thickness does not make partial and full penetration equivalent.

Identify the weld preparation and effective thickness. Apply the supplied resistance and inspection requirements to that actual detail.

Penetration describes how deeply the joint is fused. A fillet leg is a different dimension.

Scope. Do not apply the fillet factor 0.7 to a butt weld merely because both are welds. Inspection and workmanship remain part of the specified requirements.

Check and takeaway. A sketch must show the effective fused region. The outside plate outline alone cannot distinguish penetration types.

Apply the reasoning to this section’s data and conditions

A fillet weld joins surfaces at an angle and is sized by leg length.

A butt weld joins prepared edges; penetration matters.

Visual inspection checks shape and visible defects; penetrant and magnetic-particle methods seek surface defects; ultrasonic and radiographic methods seek internal defects.

Strong arithmetic assumes acceptable fabrication.

Study the full explanation and applications.

Original slide 5: Weld types and inspection. No dimensions are inferred from slide scale.

Original slide 5, weld geometry and types.

A fillet weld has a triangular section, effective throat a=0.7s and effective length Leffective=overall length−2s.

Butt welds may be full- or partial-penetration.

The slide equates full-penetration resistance to parent-metal strength, subject to the course welding and inspection conditions.

NDT means non-destructive testing; listed methods include visual, penetrant, magnetic-particle, ultrasonic and X-ray inspection.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsFrom fillet leg to effective throat2 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. An equal-leg fillet between perpendicular plates has an approximately right-triangular section.
  2. For this geometry, throat .

    It is shorter than the leg.

  3. Effective resisting area = .

    With here, capacity per length is .

  4. Use the course end allowances, minimum size and length rules; increasing the geometric length alone does not resolve every detailing check.

PPT/Joint Connections L2.pptx · slide 6: The unnumbered 6 mm weld calculation

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Change the ruler, keep the quantity

A section table uses centimetres, but the strength calculation uses millimetres. The numbers must describe the same section.

Length1 factorArea2 factors3 factorsEach centimetre becomes ten millimetres.
In the diagram, the length, square and cube contain one, two and three length factors. Each factor changes when the ruler changes.

Prediction, then explanation. Would every property increase by ten? No. The exponent determines how many factors of ten are needed.

First identify the physical quantity. Next convert each length factor. Keep force and length conversions separate when converting a moment.

1 cmn=10n mmn,1 kN m=106 N mm1\,\mathrm{cm}^n=10^n\,\mathrm{mm}^n,\qquad 1\,\mathrm{kN\,m}=10^6\,\mathrm{N\,mm}

Here n is the length exponent: 2 for area, 3 for section modulus and 4 for second moment of area.

Scope. Changing units changes neither the load nor the section. A conversion factor cannot repair a formula for the wrong physical quantity.

Check and takeaway. Illustration: 2 cm4=20,000 mm42\,\mathrm{cm}^4=20{,}000\,\mathrm{mm}^4. The fourth power belongs to the unit, not the number 2.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

Given S355 steel and Class 42 electrode, Table 9.2a gives pw=250Nmm2.

A 90° fillet of leg s=6mm has throat a=0.7s=4.2mm.

Per millimetre of effective weld, area=4.2×1=4.2mm2; resistance=4.2×250=1050N=1.05kN.

Thus q=1.05kNmm.

Required length for 105kN direct force is 1051.05=100mm effective; physical straight length is 100+2×6=112mm before other detailing constraints.

Study the full explanation and applications.

Original slide 6: The unnumbered 6 mm weld calculation. No dimensions are inferred from slide scale.

Original slide 6, weld design resistance.

In the simplified method, resistance per millimetre of weld length is 0.7spw.

The original unnumbered example uses a 6mm weld leg, S355, pw=250Nmm2, and resistance per unit length 0.7×6×2501000=1.05kNmm.

Detailing rules: minimum effective weld length max(4s,40mm); end return at least 2s; listed lap lengths 5t or 25mm, taking the larger under the full course rule.

The 105kN extension calculation above is this website's teaching addition, not another load given on the slide.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsFrom fillet leg to effective throat3 concepts · 11 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. An equal-leg fillet between perpendicular plates has an approximately right-triangular section.
  2. For this geometry, throat .

    It is shorter than the leg.

  3. Effective resisting area = .

    With here, capacity per length is .

  4. Use the course end allowances, minimum size and length rules; increasing the geometric length alone does not resolve every detailing check.

PPT/Joint Connections L2.pptx · slide 7: Recognise eccentricity in three dimensions

Add force components at each bolt

An in-plane load acts away from the bolt-group centre. Find the largest resultant bolt force.

The direct-force arrows are parallel. The moment-force arrows run tangentially around the bolt-group centre.
The direct-force arrows are parallel. The moment-force arrows run tangentially around the bolt-group centre.

Prediction, then explanation. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Locate the bolt-group centre and coordinates. Add horizontal components together and vertical components together before finding each resultant.

M=Pe,J=∑(xi2+yi2),FMx=−Myi/J,FMy=Mxi/JM=Pe,\quad J=\sum(x_i^2+y_i^2),\quad F_{Mx}=-My_i/J,\quad F_{My}=Mx_i/J

e, xi and yi use mm; J uses mm². With M in kN·mm, each moment-force component is in kN.

Scope. These expressions use the stated elastic, equal-bolt in-plane model. Out-of-plane tension and prying require another model.

Check and takeaway. Do not add force magnitudes before resolving directions. Two perpendicular forces of 3 and 4 kN give 5 kN, not 7 kN.

Treat a weld group as lines

An eccentric force creates direct line force and torsional line force in the same weld group.

The four perimeter lines represent weld runs. The interior label says No weld here: the enclosed plate area is not weld length.
The four perimeter lines represent weld runs. The interior label says No weld here: the enclosed plate area is not weld length.

Prediction, then explanation. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Find the line centroid. Integrate squared distance along the effective lines. Add direct and torsional components at every candidate critical point.

J=∫r2 dl,qMx=−My/J,qMy=Mx/JJ=\int r^2\,dl,\qquad q_{Mx}=-My/J,\quad q_{My}=Mx/J

J is line polar inertia in mm³. x and y use mm. With M in kN·mm, q is line force in kN/mm.

Scope. A solid rectangle has area inertia in mm⁴ and is not this weld-line model. Missing weld sides change the centroid and integrals.

Check and takeaway. Compare the largest resultant line force with the selected throat resistance. Keep kN/mm distinct from total force in kN.

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Apply the reasoning to this section’s data and conditions

An in-plane force rotates the bolt/weld group about its centroid and gives direct plus torsional shear.

An out-of-plane bracket load opens the joint and creates fastener tension.

For bolts, check individual shear and tension and FsPs+FtPnom≤1.4; Pnom=0.8Aspt.

The interaction limit is 1.4, not 1.0.

Study the full explanation and applications.

Original slide 7: Recognise eccentricity in three dimensions. No dimensions are inferred from slide scale.

Original slide 7, combined stresses in eccentric connections.

Upper half, in-plane: direct shear Fs is shared equally; torsional force FT is proportional to radius from the centroid; resultant FR=Fs2+FT2+2FsFTcos(φ),φ is the angle between the two forces, written as “phi” in the source.

Lower half, out-of-plane: direct shear is shared equally; tension uses the rotation model about the lowest bolt row.

The source still uses upper-case FT for tension and gives the interaction expression FsPs+FTPnom≤1.4.

The two uses of FT have different physical meanings and cannot be interchanged.

The explanation above writes tension as Ft.

The distinction is made explicit here.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsAdd direct and torsional bolt forces4 concepts · 4 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Assign signed coordinates to the bolts relative to the group centroid.
  2. For the equal-bolt elastic model, the direct force is per bolt.
  3. Moment magnitude is .

    Its sign follows the load direction.

    For signed M: , , .

  4. Add signed x and y components at each bolt, then take the resultant.

    The longest arrow shows the critical bolt in this illustration.

PPT/Joint Connections L2.pptx · slide 8: A reusable connection workflow

Use the same mechanism: Keep load categories separate. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

Use the same mechanism: Count cuts through each loaded bolt. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Apply the reasoning to this section’s data and conditions

Resolve factored actions; classify force direction; label geometry.

Calculate individual fastener demand.

Calculate all applicable fastener and plate resistances.

Check layout; state the governing result and assumptions.

The linked worked example explains this sequence.

The corresponding tutorial shows the complete application and answer.

Study the full explanation and applications.

Original slide 8: A reusable connection workflow. No dimensions are inferred from slide scale.

Original slide 8, student solution procedure.

Step 1: calculate Pu=1.4dead load+1.6imposed load.

Step 2: check single/double shear, bearing, bolt tension or weld-throat resistance.

Step 3: check plate tension using gross and effective net areas Ae.

Step 4: check code requirements for pitch, edge distance, transverse spacing and weld end returns.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsFollow the calculation sequence8 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Locate the load, supports, connection geometry and any stated assumptions.
  2. Keep given values, table lookups and calculated values distinct; reconcile their units.
  3. The calculation player steps through the existing expressions in their original order.
  4. Compare demand with resistance or the relevant limit.

    Keep missing inputs and conditional conclusions explicit.

PPT/Steel Beam Design L3.pptx · slide 1: Beam design

Balance the isolated beam

Find the two vertical reactions before calculating internal shear or moment.

A / RₐB / RᵦPaL
A and B are vertical supports. The downward load acts at distance a from A. Its distance from B is L − a.

Prediction, then explanation. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Take moments about A. Reaction A has zero lever arm there. Then use vertical force balance to find reaction A.

RBL=Pa,RA+RB=PR_B L=Pa,\qquad R_A+R_B=P

P, RA and RB are forces in kN. L is support spacing and a is load position, both in m.

Scope. These expressions describe one point load on a simply supported beam. Add other loads through equilibrium; keep their actual positions.

Check and takeaway. Illustration: P = 60 kN, L = 6 m and a = 2 m give RB = 20 kN and RA = 40 kN.

Internal tension and compression resist moment

Find which section resistance applies before comparing it with the moment demand.

In sagging bending, the upper region compresses and the lower region stretches. Together their forces form a resisting couple.
In sagging bending, the upper region compresses and the lower region stretches. Together their forces form a resisting couple.

Prediction, then explanation. A larger appropriate section modulus raises resistance at fixed strength. Local plate buckling can restrict the usable modulus.

Classify the section first. At low shear, use the elastic expression for Class 3 or the prescribed capped plastic expression for Classes 1 and 2.

Mc=min⁡(pyS,1.2pyZ)for Class 1/2 at low shearM_c=\min(p_yS,1.2p_yZ)\quad\text{for Class 1/2 at low shear}

py uses N/mm². S is plastic modulus and Z is elastic modulus, both in mm³. Mc then uses N·mm.

Scope. This is section resistance, not whole-member LTB resistance. High shear and Class 4 require their appropriate treatment.

Check and takeaway. Selecting the larger of the two capped terms defeats the cap. Use their minimum.

The web carries the shear check

Compare the applied shear with the resistance of the prescribed shear area.

At the imaginary cut, opposing arrows resist relative sliding. The rolled-UB calculation below assigns the shear area to the web.
At the imaginary cut, opposing arrows resist relative sliding. The rolled-UB calculation below assigns the shear area to the web.

Prediction, then explanation. At fixed design strength and depth, increasing web thickness increases this shear resistance.

Calculate the prescribed shear area. Multiply by the design shear stress from the course rule. Then compare matching force units.

Av=Dt,Vc=pyAv/3A_v=Dt,\qquad V_c=p_yA_v/\sqrt{3}

D is overall depth; t is web thickness, in mm. Av uses mm². py uses N/mm², giving Vc in N.

Scope. Apply this area definition to the stated rolled section. Check web slenderness separately. The factor 0.6 is the low-shear threshold, not this resistance coefficient.

Check and takeaway. A shear pass alone does not prove bending, deflection or local support-web adequacy.

Apply the reasoning to this section’s data and conditions

A beam mainly resists transverse load by bending and shear.

Its vertical supports and sideways restraints serve different purposes: a lateral restraint need not be a vertical support.

Study the full explanation and applications.

Original slide 1: Beam design. No dimensions are inferred from slide scale.

Original slide 1: Steel Beam Design, Chapter 3.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsBalance reactions and moments4 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. This demonstrator is a simply supported 6 m beam with a 60 kN point load.

    It is not the page’s original loading diagram.

  2. .

    Moving the load towards B increases .

  3. .

    The two upward reactions must sum to P.

  4. With the load at midspan, .

    End couples, UDLs and overhangs require their own equilibrium terms.

PPT/Steel Beam Design L3.pptx · slide 2: Beam learning objectives

Use the same mechanism: Keep load categories separate. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

A cut reveals the internal actions

Find where the beam moment is largest. A large load arrow alone does not locate that point.

The dashed imaginary cut separates two beam pieces. The opposing arrows represent the shear action between those pieces.
The dashed imaginary cut separates two beam pieces. The opposing arrows represent the shear action between those pieces.

Prediction, then explanation. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Balance the forces on the cut piece to get V. Balance their moments about the cut to get M. Evaluate each load region separately.

V(x)=RA−wx,M(x)=RAx−wx22V(x)=R_A-wx,\qquad M(x)=R_Ax-\frac{wx^2}{2}

x and L use m; w uses kN/m; V uses kN; M uses kN·m. These lines apply before any point load.

Scope. A point load adds a shear jump. A concentrated couple adds a moment jump. Check load points, supports and overhang roots too.

Check and takeaway. A UDL gives a sloping shear line and a curved moment line. A flat moment diagram therefore cannot represent a loaded UDL region.

Apply the reasoning to this section’s data and conditions

A complete beam answer progresses through load analysis, section classification, shear, bending, local web checks where required, LTB where unrestrained, and deflection.

Section selection is iterative because a heavier trial section also changes self-weight.

Study the full explanation and applications.

Original slide 2: Beam learning objectives. No dimensions are inferred from slide scale.

Original slide 2, Learning Objectives: understand effective length, lateral/torsional restraint and destabilizing loads.

Calculate loads; and check simply supported beams under the Hong Kong steel code for classification, shear, bending, LTB, deflection, web bearing and web buckling.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsFollow the calculation sequence12 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Locate the load, supports, connection geometry and any stated assumptions.
  2. Keep given values, table lookups and calculated values distinct; reconcile their units.
  3. The calculation player steps through the existing expressions in their original order.
  4. Compare demand with resistance or the relevant limit.

    Keep missing inputs and conditional conclusions explicit.

PPT/Steel Beam Design L3.pptx · slide 3: Compression flange restraint

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: Internal tension and compression resist moment. A larger appropriate section modulus raises resistance at fixed strength. Local plate buckling can restrict the usable modulus.

Apply the reasoning to this section’s data and conditions

The flange in compression can move sideways and twist the beam.

The slide’s 2.5% restraint-force rule is a strength requirement for the restraint system, not evidence that any slab is automatically an effective restraint.

Confirm which flange is in compression and whether the attachment prevents lateral movement/twist.

Study the full explanation and applications.

Original slide 3: Compression flange restraint. No dimensions are inferred from slide scale.

Original slide 3: full lateral restraint follows clause 8.2.

The compression flange is restrained over its entire length, and the restraint system must resist at least the following fraction of the maximum design compressive force: 2.5%.

Partial restraint provides restraint only at selected positions.

Under clause 8.3, check each segment for LTB, effective length LE and moment resistance Mb above.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsA beam bends sideways and twists2 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For the illustrated sagging beam the top flange is compressed.
  2. The unrestrained compression flange can move sideways while the complete cross-section twists.
  3. Only effective restraints divide the member into unbraced segments.

    They do not automatically add vertical supports.

  4. Use the segment effective length, section properties and matching moment factor.

    This is an exaggerated mode shape, not a calculated displacement.

PPT/Steel Beam Design L3.pptx · slide 4: Classify the beam

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Apply the reasoning to this section’s data and conditions

Under major-axis bending the flanges and web have different stress distributions.

Use the flange outstand bT and web dt from the section table, compare with the correct multiples of ε, and select the worse class.

Do not substitute overall depth D for clear web depth d.

Study the full explanation and applications.

Original slide 4: Classify the beam. No dimensions are inferred from slide scale.

Original slide 4: section classification depends on width/thickness ratios and steel strength.

Class 1, plastic, can form a plastic hinge with adequate rotation.

Class 2, compact, can reach plastic moment resistance with limited rotation.

Class 3, semi-compact, can yield at the extreme fibre, but local buckling prevents full plastic moment resistance.

Class 4, slender, buckles locally before yielding and requires an effective section.

In the source expression ε=275py, py is measured in Nmm2 is substituted.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsWhy thin elements buckle locally1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The flange outstand and web have different widths, thicknesses and edge support conditions.
  2. A thinner plate can wrinkle locally before the complete member loses stability.
  3. Class 1 allows plastic rotation.

    Class 2 reaches plastic resistance.

    Class 3 reaches elastic resistance.

    Class 4 requires effective properties.

  4. Check every relevant compression element with the supplied limits and stress distribution.

    The deformation shown is qualitative.

PPT/Steel Beam Design L3.pptx · slide 5: Shear resistance

Use the same mechanism: The web carries the shear check. At fixed design strength and depth, increasing web thickness increases this shear resistance.

Shear and bending share the web

Decide whether the unreduced bending resistance remains applicable at the section being checked.

The same web region participates in shear and longitudinal bending stress. The two demands must be evaluated at one section.
The same web region participates in shear and longitudinal bending stress. The two demands must be evaluated at one section.

Prediction, then explanation. Raising shear beyond the specified threshold can reduce available bending resistance. A distant maximum shear is not the coexistent shear.

Find the moment-check position. Evaluate the shear there. Compare it with the low-shear threshold before selecting the resistance expression.

V≤0.6Vcis the course low-shear conditionV\le0.6V_c\quad\text{is the course low-shear condition}

V is shear at the checked section; Vc is its shear resistance. Both use the same force unit.

Scope. Above the threshold, use the supplied reduction expression. The threshold itself is not a substitute resistance formula.

Check and takeaway. If the maximum shear anywhere is below the threshold, all sections satisfy that low-shear condition. Otherwise check the actual positions.

Apply the reasoning to this section’s data and conditions

For a rolled I, H or channel under the course major-axis shear model, Av=tD.

Then Vc=pyAv3.

Convert N to kN only after multiplying stress by area.

If V≤0.6Vc the low-shear bending rule applies; passing V≤Vc alone does not establish low shear.

Study the full explanation and applications.

Original slide 5: Shear resistance. No dimensions are inferred from slide scale.

Original slide 5, clause 8.2.1: shear resistance Vc=pyAv3≥V.

Hot-rolled I/H/channel sections use Av=tD.

The slide gives the following for RHS: Av=2td.

Low shear means V≤0.6Vc; high shear means V>0.6Vc and requires reduced moment resistance under clause 8.2.2.2.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsSee shear in the web2 concepts · 9 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Internal shear keeps the two sides of the cut in vertical equilibrium.
  2. For the course’s common I-section case, the web provides the principal shear area.

    Use the specified definition.

  3. A slender web may require a different shear-buckling route before a simple shear-resistance formula is used.
  4. Use where applicable in the course.

    Convert N to kN before comparing with design shear.

PPT/Steel Beam Design L3.pptx · slide 6: Low and high shear bending

Use the same mechanism: Internal tension and compression resist moment. A larger appropriate section modulus raises resistance at fixed strength. Local plate buckling can restrict the usable modulus.

Use the same mechanism: Shear and bending share the web. Raising shear beyond the specified threshold can reduce available bending resistance. A distant maximum shear is not the coexistent shear.

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Apply the reasoning to this section’s data and conditions

For Class 1/2 at low shear, Mc=min(pyS,1.2pyZ).

Above 0.6Vc, reduce bending resistance using the course high-shear formula, with ρ=(2VVc−1)2.

At V=0.8Vc, ρ=(1.6−1)2=0.36.

Use the relevant shear-area term from the full formula, not 36% of the entire bending resistance by guesswork.

Study the full explanation and applications.

Original slide 6: Low and high shear bending. No dimensions are inferred from slide scale.

Original slide 6: for low shear V≤0.6Vc.

Class 1/2: Mc=pyS≤1.2pyZ.

Class 3: Mc=pyZ or, under the applicable effective-modulus method, use pySeff.

Class 4: Mc=pyZeff or, under the applicable reduced-strength method, use pyrZ.

These alternatives are distinct code-permitted methods.

Do not simply choose the larger result.

For high shear V>0.6Vc in Class 1/2 sections: Mc=py(S−ρSv)≤1.2py(Z−ρSv1.5),ρ=(2VVc−1)2 above.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsCompression and tension across a section3 concepts · 11 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For sagging, the top flange is in compression and the bottom in tension; hogging reverses this.
  2. Elastic bending stress varies with distance from the neutral axis: .
  3. The section class governs whether elastic, plastic or effective properties may be used.
  4. Use the shear at the section under examination.

    The largest shear elsewhere is not automatically coexistent.

PPT/Steel Beam Design L3.pptx · slide 7: Local web bearing and buckling

A concentrated force spreads into the web

Check local web resistance at a support or concentrated load, even if overall beam strength passes.

Compare Narrow contact with Wide contact. Both receive the same force, but the wider contact distributes it over a longer region.
Compare Narrow contact with Wide contact. Both receive the same force, but the wider contact distributes it over a longer region.

Prediction, then explanation. A longer valid stiff-bearing length can spread the same force over more web. A flexible contact is not automatically stiff bearing.

Match the actual bearing geometry to its source sketch. Use that sketch’s dimensions and permitted spread to calculate the resisting region.

b₁ is stiff-bearing length in mm. Web thickness and applicable design strength enter the prescribed local resistance equation.

Scope. End and interior cases can differ. A lateral-restraint symbol does not provide a bearing length or a load-introduction detail.

Check and takeaway. If bearing geometry is missing, give the applicable symbolic check and state the missing input. Do not borrow another example’s dimensions.

The loaded web can act as a short strut

A concentrated load can buckle the web instead of crushing it. This requires a separate local check.

Local bowWebFlangeExaggerated
The compressed strip lies below the load. Its possible lateral bow differs from whole-beam lateral-torsional buckling.

Prediction, then explanation. Reduced local restraint can increase the relevant effective length and reduce local buckling resistance.

First calculate the source model’s effective strip and base resistance. Then apply the branch required by local restraint and load position.

Local web effective length is not the beam span or the LTB segment length. Use the symbol definition in the selected local formula.

Scope. The short-strut picture explains a mechanism; it is not a derivation of every coefficient in the supplied web rule.

Check and takeaway. A local bearing pass does not establish a local buckling pass. State both conclusions and any unresolved restraint condition.

Apply the reasoning to this section’s data and conditions

A support reaction or concentrated load presses through a finite bearing length into the web.

Bearing and web buckling are separate checks.

Identify the stiff bearing length, load position near an end, and lateral restraint.

This slide only displays the ae≥0.7d branch.

The full lecture includes the other case.

Missing contact dimensions prevent a definite local capacity.

Study the full explanation and applications.

Original slide 7: Local web bearing and buckling. No dimensions are inferred from slide scale.

Original slide 7, clause 8.4.10: web bearing Pbw=(b1+nk)tpyw; load spreads at 1:2.5 to the root fillet.

For hot-rolled sections, k=T+r.

The web-buckling resistance Px expression shown requires rotational and lateral restraint to the flange.

When ae≥0.7d, Px=25εt(b1+nk)dPbw.

b1 is bearing length.

nk is the additional dispersion length selected for the end location.

Dimensions and the applicable branch must still be identified from the actual question.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsSpread a concentrated force into the web2 concepts · 5 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A concentrated reaction first enters through the bearing/contact region.
  2. The flange and root geometry spread the force before it enters the web.
  3. A wider effective bearing region can reduce local stress for the same force.
  4. End distance, stiff bearing length and restraint conditions must come from the original question.

    The illustrated dimensions explain the mechanism.

    They do not replace the original question data.

PPT/Steel Beam Design L3.pptx · slide 8: LTB factors and effective length

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

Compute λ=LEry, then v and λLT=uvλβW, and read pb.

The slide’s suggestion to multiply destabilizing length by 1.2 is not a universal rule.

In the full lecture table, select the applicable loading column.

Then select the actual end-restraint row.

Load height and freedom to twist determine applicability.

Study the full explanation and applications.

Original slide 8: LTB factors and effective length. No dimensions are inferred from slide scale.

Original slide 8: LTB must be checked when the compression flange is not restrained along its full length.

Original notation is retained as mLtMx≤Mb and Mx≤Mcx; λlt=uvλβw.

For Class 1/2, Mb=pbSx.

The diagram symbol mLt, λlt, βw corresponds to this lesson's mLT, λLT, βW; source letter case is retained.

The slide says destabilizing loading multiplies LE by 1.2.

Applicability limits and the full lookup method are explained above.

This is not a fixed multiplier for every restraint condition.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsA beam bends sideways and twists2 concepts · 6 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For the illustrated sagging beam the top flange is compressed.
  2. The unrestrained compression flange can move sideways while the complete cross-section twists.
  3. Only effective restraints divide the member into unbraced segments.

    They do not automatically add vertical supports.

  4. Use the segment effective length, section properties and matching moment factor.

    This is an exaggerated mode shape, not a calculated displacement.

PPT/Steel Beam Design L3.pptx · slide 9: Fully restrained workflow

Use the same mechanism: Keep load categories separate. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Apply the reasoning to this section’s data and conditions

Resolve loads and reactions; draw the critical moment/shear; choose a trial section.

Check its class, V and Mc.

Check local web behaviour.

Calculate service deflection.

State the physical reason LTB is restrained rather than silently omitting it.

Study the full explanation and applications.

Original slide 9: Fully restrained workflow. No dimensions are inferred from slide scale.

Original slide 9, six steps for a fully restrained steel beam. (1) Determine dead and imposed loads. (2) Calculate design moment Mx and shear V. (3) Make a trial section selection using Sx=Mxpy. (4) Classify using width/thickness ratios. (5) Check bending and shear resistances. (6) Check local web bearing/buckling and deflection.

The trial-selection formula does not replace these checks.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsFollow the calculation sequence12 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Locate the load, supports, connection geometry and any stated assumptions.
  2. Keep given values, table lookups and calculated values distinct; reconcile their units.
  3. The calculation player steps through the existing expressions in their original order.
  4. Compare demand with resistance or the relevant limit.

    Keep missing inputs and conditional conclusions explicit.

PPT/Steel Beam Design L3.pptx · slide 10: Unrestrained workflow

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Moment shape matters within one segment

Represent a nonuniform moment distribution in the applicable member-buckling equation.

The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.
The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.

Prediction, then explanation. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Evaluate moments from the true whole-beam analysis at the required positions. Apply the exact table’s weights, signs and lower bound.

mLT is an LTB factor. mx and my belong to the specified flexural checks. They are not interchangeable.

Scope. Some rules use magnitudes; others require signed ordinates. A factor does not reduce the actual moment used in a local section check.

Check and takeaway. Measure quarter points from the segment start, not automatically from the beam’s left support.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

Divide the beam at effective lateral restraints.

For each relevant segment find its maximum moment and moment shape, obtain mLT, calculate effective slenderness and Mb, and compare mLTMmax≤Mb.

The segment with the longest length is not necessarily the governing one.

Study the full explanation and applications.

Original slide 10: Unrestrained workflow. No dimensions are inferred from slide scale.

Original slide 10, six steps for a beam without full lateral restraint. (1) Determine design actions. (2) The trial may need to be heavier because pb<py. (3) Classify and identify normal/destabilizing loading. (4) Calculate slenderness using λ=LEry. (5) Determine λlt and look up bending strength in Table 8.3a. (6) Check mLtMx≤Mb, where Mb=pbSx.

For the source symbol λlt, mLt and its correspondence to this lesson's upper-case subscript, see slide 8.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsA beam bends sideways and twists3 concepts · 5 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For the illustrated sagging beam the top flange is compressed.
  2. The unrestrained compression flange can move sideways while the complete cross-section twists.
  3. Only effective restraints divide the member into unbraced segments.

    They do not automatically add vertical supports.

  4. Use the segment effective length, section properties and matching moment factor.

    This is an exaggerated mode shape, not a calculated displacement.

PPT/Steel Beam Design L3.pptx · slide 11: Finish with serviceability and a conclusion

Use the same mechanism: A safe beam can still sag too far. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.

Apply the reasoning to this section’s data and conditions

Use the stated service load and unamplified elastic stiffness EI.

For central P, δ=PL348EI.

For UDL w, δ=5wL4384EI.

Convert cm4 to mm4 by ×104.

State the largest utilization and any incomplete local checks.

Study the full explanation and applications.

Original slide 11: Finish with serviceability and a conclusion. No dimensions are inferred from slide scale.

Original slide 11, design and exam tips: establish restraints before selecting the calculation method; include classification.

Keep serviceability deflection separate from strength checks.

The example limit for brittle finishes is L360.

State the applicable Hong Kong code clauses and the conclusion.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsSee stiffness and deflection1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Use the specified SLS load, span and support arrangement.

    The demonstrator has a full-span UDL.

  2. The loaded beam bends.

    The deformation is exaggerated so its shape can be seen.

  3. For a simply supported full-span UDL, .

    Double L with w, E and I unchanged: δ becomes 16 times as large.

  4. The readout uses , and .

    Select the finish/support-specific limit from the original table.

PPT/Steel Column Design L4.pptx · slide 1: Column design

A strong cross-section can belong to an unstable member

A column carries axial compression and bending. Explain why more than one check is required.

The three boxes name separate checks: Section, Flexural and LTB. The bottom caption explains that passing one does not pass the others.
The three boxes name separate checks: Section, Flexural and LTB. The bottom caption explains that passing one does not pass the others.

Prediction, then explanation. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Separate cross-section, flexural-buckling and LTB interaction equations. Use each equation’s own denominators and first-order or amplified moments.

AgpyA_g p_y is a section axial resistance. AgpcA_g p_c is a member compression resistance. Elastic pyZp_y Z and prescribed McM_c are different bending denominators.

Scope. Preserve the course barred-moment definitions and Eq. 8.81 convention. Do not substitute plastic moduli into an elastic denominator.

Check and takeaway. Report each requested utilisation and the governing check. The largest properly calculated ratio identifies the closest limit.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

A column resists compression, often with bending.

A short section can crush.

A long member can buckle before reaching material strength.

These mechanisms require separate checks.

Study the full explanation and applications.

Original slide 1: Column design. No dimensions are inferred from slide scale.

Original slide 1: Steel Column Design (CON4334), Chapter 4; understanding the content, effective length and member resistance.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsA strong slice can belong to an unstable member2 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

PPT/Steel Column Design L4.pptx · slide 2: Column learning objectives

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

Learn restraint interpretation, two-axis slenderness, curve selection, compression resistance and combined axial/bending checks.

A single axial capacity is insufficient when the load acts eccentrically.

Study the full explanation and applications.

Original slide 2: Column learning objectives. No dimensions are inferred from slide scale.

Original slide 2, Learning Objectives: understand effective length and section classification; correctly design columns carrying axial force alone; evaluate columns under combined axial force and bending in simple and continuous construction.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsWhy thin elements buckle locally3 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The flange outstand and web have different widths, thicknesses and edge support conditions.
  2. A thinner plate can wrinkle locally before the complete member loses stability.
  3. Class 1 allows plastic rotation.

    Class 2 reaches plastic resistance.

    Class 3 reaches elastic resistance.

    Class 4 requires effective properties.

  4. Check every relevant compression element with the supplied limits and stress distribution.

    The deformation shown is qualitative.

PPT/Steel Column Design L4.pptx · slide 3: Effective length and slenderness

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

For each axis, LE=KL and λ=LEr.

The dimensionless factor K represents the stated end restraint/sway condition.

Millimetres must be used in both numerator and denominator.

Tying the weak direction reduces LEy only if the tie actually restrains that buckling direction.

Study the full explanation and applications.

Original slide 3: Effective length and slenderness. No dimensions are inferred from slide scale.

Original slide 3, compression members and effective length.

Buckling resistance depends on slenderness λ=LEr; effective length LE=KL is the product of factor K and actual length L.

Use rotational and positional restraint conditions to select from Table 8.6.

Compression resistance for plastic, compact and semi-compact sections: Pc=Agpc above.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsEffective length and buckling axes1 concept · 5 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

PPT/Steel Column Design L4.pptx · slide 4: Select a strut curve before a number

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Move between two known values

The required slenderness lies between two table rows. Estimate the strength on the straight segment between those rows.

xy(70, 200)(74, 192)(80, 180)70748040% of input interval → 40% of output change
The marked position lies partway along the horizontal interval. Use the same fraction of the vertical change.

Prediction, then explanation. If the second strength is lower, moving toward that row must reduce the interpolated strength.

Subtract the lower input to find distance travelled. Divide by the input interval. Multiply that fraction by the output change.

f=x−x0x1−x0,y=y0+f(y1−y0)f=\frac{x-x_0}{x_1-x_0},\qquad y=y_0+f(y_1-y_0)

x is the required input. The two known pairs are (x₀, y₀) and (x₁, y₁). f has no unit.

Scope. Use one table, curve and strength column. This interpolation does not permit extrapolation or inventing an intermediate steel section.

Check and takeaway. Illustration: between strengths 200 and 180, a fraction of 0.4 gives 192 N/mm². The result lies between both endpoints.

Apply the reasoning to this section’s data and conditions

Read Table 8.7 by section type, maximum thickness and buckling axis.

A rolled H section with thickness≤40mm uses curve b about x and c about y.

Then read Table 8.8 using that curve, py and slenderness; interpolate between bounding rows.

Study the full explanation and applications.

Original slide 4: Select a strut curve before a number. No dimensions are inferred from slide scale.

Original slide 4, strut-strength tables.

Compressive strength pc depends on section type, design strength py, slenderness λ and buckling curve.

Table 8.7 selects curves a, b, c and d using section geometry and residual stress.

Tables 8.8(a) to (d) on the slide give design strength in Nmm2 for steel grades including S275, S355 and S460.

Use the applicable curve and table heading; steel grade alone does not select the table.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsEffective length and buckling axes3 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

PPT/Steel Column Design L4.pptx · slide 5: Section and member interactions

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Two simultaneous actions use one component

Check a component that carries shear and tension, or compression and bending, at the same time.

The bolt receives two labelled arrows: tension and shear. The caption requires both individual checks and the combined check.
The bolt receives two labelled arrows: tension and shear. The caption requires both individual checks and the combined check.

Prediction, then explanation. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

First apply the individual checks. Next use the exact combined equation and its definitions. Keep demands from the same load case.

FsPs+FtPnom≤1.4\frac{F_s}{P_s}+\frac{F_t}{P_{nom}}\le1.4

This is the course bolt interaction rule. Fs and Ft are bolt demands; Ps and Pnom are their specified resistance denominators.

Scope. The 1.4 limit and nominal tension denominator do not apply to column equations. Their limits and moment definitions are separate.

Check and takeaway. A sum above one can pass this bolt rule while still needing individual checks. A pass must name the actual equation used.

Apply the reasoning to this section’s data and conditions

Cross-section interaction combines axial utilization and bending utilizations at the same section.

Member equations include reduced compression/LTB resistance and moment factors.

Follow the full lecture’s elastic denominators and overbars: compact slide notation can hide whether a moment is first-order or amplified.

Study the full explanation and applications.

Original slide 5: Section and member interactions. No dimensions are inferred from slide scale.

Original slide 5, combined axial force and bending (clause 8.9).

A column must satisfy both section resistance and member buckling resistance.

Clause 8.9.1 gives the section expression FcAgpy+MxMcx+MyMcy≤1.

The member interaction expressions in clause 8.9.2 account for second-order overall sway and member bending (P–Δ and P–δ).

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsA strong slice can belong to an unstable member2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

PPT/Steel Column Design L4.pptx · slide 6: Frame classification and amplification

Use the same mechanism: Restraints define the analysis model. A joint that permits beam rotation does not automatically remove all column moment. Eccentric reactions may still bend the column.

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Apply the reasoning to this section’s data and conditions

Elastic critical load factor λcr measures proximity to global instability.

Use the lecture’s non-sway/sway/ultra-sensitive boundaries and applicable amplification method.

If the problem already supplies amplification factors, apply them once to the specified first-order moments.

An already amplified MLT must not be amplified again.

Study the full explanation and applications.

Original slide 6: Frame classification and amplification. No dimensions are inferred from slide scale.

Original slide 6, sections 2.3 and 2.4: frame classification and amplification.

Non-sway frames: λcr≥10, allowing overall P–Δ effects to be ignored.

Sway frames: 5≤λcr<10; highly sway-sensitive frames: λcr<5, requiring a higher-order second-order analysis.

The slide gives moment amplification factor λcrλcr−1 to account for second-order sway, subject to the applicability conditions of the course method.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsRestraints, sway and imperfections2 concepts · 3 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A frame needs a defined path for horizontal force as well as gravity.
  2. Pinned joints alone do not provide frame moment resistance; sway restraint needs a real structural system.
  3. Diagonal bracing carries horizontal action through axial forces.

    This sketch does not assign a numerical frame classification.

  4. Use the specified imperfection/notional-force model and critical-load criteria.

    Avoid counting alternative imperfection models twice.

PPT/Steel Column Design L4.pptx · slide 7: Simple construction

An eccentric beam reaction bends the column

A simple beam joint delivers a vertical reaction away from the column centre. Find the resulting column moments.

The reaction arrow is offset by e from the column centre. The upper and lower arrows show where the joint moment is shared.
The reaction arrow is offset by e from the column centre. The upper and lower arrows show where the joint moment is shared.

Prediction, then explanation. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Sum axial forces first. Calculate the signed eccentric moments. Share the net joint moment between upper and lower columns using the stated stiffness model.

M=Re,Mlower=MKlowerKupper+KlowerM=Re,\qquad M_{lower}=M\frac{K_{lower}}{K_{upper}+K_{lower}}

R is reaction; e is perpendicular eccentricity. K denotes the stiffness measure prescribed for moment sharing.

Scope. Equal sharing requires equal stated stiffness. Use actual storey length where the special simple-construction LTB rule requires it.

Check and takeaway. A pin-like beam connection can still cause an eccentric reaction moment in the column. Joint rotation and reaction location are separate facts.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

Nominally pinned beams can still deliver eccentric reactions to a column.

Calculate reaction×eccentricity and share joint moment according to the prescribed column stiffnesses.

For the course simple-construction LTB shortcut, λLT=0.5Lry uses actual column length L, not the flexural effective length LE.

Study the full explanation and applications.

Original slide 7: Simple construction. No dimensions are inferred from slide scale.

Original slide 7, columns in simple construction.

Beams are assumed fully loaded and simply supported, with all equivalent-moment factors m=1.0.

Equivalent slenderness for lateral-torsional buckling λLT=0.5(Lry),L is storey height, not LE.

Under multi-storey clause 8.7.8, pattern loading need not be considered.

Nominal moments come from reaction eccentricity, taking the larger eccentricity from a load line 100mm from the column face or at the centre of stiff bearing.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsEccentric reactions and stiffness sharing3 concepts · 3 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A beam reaction can act away from the column centre even at a nominally pinned beam connection.
  2. .

    Opposing reactions can cancel part of the signed moment, while both still add compression.

  3. The course simple model distributes the joint moment in proportion to of the columns above and below.
  4. Equal relevant stiffness gives half each.

    A roof joint with no upper column is a different case.

PPT/Steel Column Design L4.pptx · slide 8: Write both buckling checks accurately

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Apply the reasoning to this section’s data and conditions

Keep flexural-buckling and LTB interaction equations separate.

The full lecture Eq. 8.80 uses amplified bending moments; Eq. 8.81 uses the specified amplified MLT and first-order minor-axis My.

The slide is a memory aid.

Use the full derivation to restore subscripts, bars and elastic moment denominators.

Study the full explanation and applications.

Original slide 8: Write both buckling checks accurately. No dimensions are inferred from slide scale.

Original slide 8, summary of column checks.

The source section expression is [FcAgpy]+[MxMcx]+[MyMcy]≤1, the same for simple and continuous construction.

The source member expression for simple construction is [FcPcy]+[mLTMLTMb]+[myMyMcy]≤1,m=1.0; continuous construction selects specific m values from Tables 8.9 and 8.4.

This reproduces the source diagram without silently replacing its Mcy with the elastic denominator in the full lecture.

Actual solutions must use the complete formulas and amplified-moment definitions linked above.

This summary, which omits overbars, cannot replace them.Open full-size image

Mechanism detailsA strong slice can belong to an unstable member1 concept · 3 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

PPT/Steel Column Design L4.pptx · slide 9: The worked-example sequence

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: An eccentric beam reaction bends the column. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Apply the reasoning to this section’s data and conditions

Example 1 begins with axial compression.

Example 2 shows how a weak-axis tie changes stability.

Example 3 transfers eccentric beam reactions into column forces and moments.

Example 4 builds floor loads and applies the stated imposed-load reduction.

The full notes also contain Example 5 for combined end moments, which remains required even though this summary omits it.

Study the full explanation and applications.

Original slide 9: The worked-example sequence. No dimensions are inferred from slide scale.

Original slide 9, design examples and learning resources.

Example 1: pin-ended column under axial force.

Example 2: pin-ended column tied against minor-axis buckling.

Example 3: column under axial force and bending in simple construction.

Example 4: axially loaded column using tributary area and load reduction.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsEffective length and buckling axes5 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

PPT/Steel Column Design L4.pptx · slide 10: References and further study

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

The slide names references and suggests external video searches.

This offline course contains the needed teaching locally.

When reading outside material, compare code edition, axis labels, yield strength rules and partial factors before using any equation.

Do not combine Eurocode and supplied HK design expressions.

Study the full explanation and applications.

Original slide 10: References and further study. No dimensions are inferred from slide scale.

Original slide 10, References & Useful Links: Hong Kong Code of Practice for the Structural Use of Steel 2011; and Steelwork Design Guide to BS 5950 / HK Code (CON4334 course notes).

The original suggested YouTube search strings are retained for recognition: Steel Column Design EC3 / BS5950 Workflow (column design workflow) and Effective Length Buckling Civil Engineering (effective length and buckling).

These are source suggestions for further study.

This site does not depend on external videos or combine different codes.

Do not infer dimensions from slide scale.Open full-size image

Mechanism detailsRead a table without losing the keys2 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Name the required property: material strength, section property, buckling strength or a moment factor.
  2. Keep section size, steel grade, thickness band, curve and axis as separate lookup keys.
  3. , and require different conversion powers.

    Do not use adjacent columns interchangeably.

  4. Use bracketing rows within the same valid column.

    The original page remains the source of all table values.

NOTE.docx · rendered page 1: material and capacities

Use the same mechanism: Separate stiffness, strength and ductility. Raising the yield level alone need not change the initial slope. The same elastic load can therefore give similar deformation.

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Use the same mechanism: Internal tension and compression resist moment. A larger appropriate section modulus raises resistance at fixed strength. Local plate buckling can restrict the usable modulus.

Apply the reasoning to this section’s data and conditions

E=205000Nmm2 is elastic stiffness.

ε=275py scales classification limits.

Read py from thickness before calculating ε.

The note lists Mc=min(pyS,1.2pyZ).

However, this is the Class 1/2 low-shear rule, not the Class 3/4 rule.

Vc=pyAv3 uses Av=tD for the specified rolled sections and shear direction.

Pt=Aepy needs net-area/shear-lag adjustments for connected angles.

Pc=Agpc needs separate curve and slenderness lookups about both axes.

Despite the heading “Member Checks”, Mc and Vc alone are cross-section resistances; instability needs additional member checks.

Original Word page 1; the equations are embedded objects and were inspected as an image.

Original Word document p.1, Student Quick-Reference Guide: Steelwork Design.

Equations are embedded objects inspected as images. (1) Materials: Young's modulus E=205,000Nmm2; steel-grade factor ε=(275py)0.5; design strength varies with grade and plate thickness, for example S355 at thickness ≤16mm,py=355Nmm2. (2) Bending: Mcx=pySx≤1.2pyZx,Mcy=pySy≤1.2pyZy, subject to the classification and low-shear conditions above.

Shear: Vc=pyAv3.

For hot-rolled I, H and channel sections, use Av=tD.

Tension: Pt=Aepy, adjusting net area for the bolted/welded connection type.

Compression: Pc=Agpc, with slenderness λ=Ler; lower-case subscript Le is retained from the source.Open full-size image

Prediction and explained answer.

Why can Pc be less than Agpy?

Answer and reasoning

pc accounts for member buckling and is normally below py; py only describes the material/section strength.

Mechanism detailsElasticity, yielding and ductility9 concepts · 18 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Stress is force divided by area.

    Strain measures change in length relative to original length.

  2. Before yielding, stress is approximately .

    E controls the elastic slope.

  3. Further strain includes permanent deformation.

    Higher yield strength does not by itself increase E.

  4. Strength, stiffness and ductility answer different questions.

    This schematic is not a measured stress–strain curve.

NOTE.docx · rendered page 2: deflection and fasteners

Use the same mechanism: A safe beam can still sag too far. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.

Use the same mechanism: Count cuts through each loaded bolt. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Apply the reasoning to this section’s data and conditions

For a simply supported prismatic beam with constant EI, central-point-load deflection is PL348EI, and full-span UDL deflection is 5wL4384EI.

The Word note correctly shows L3 for the point load.

The separate Data File has a conflicting exponent.

Select the service load and limit row, then use consistent N and mm.

Bolt Ps=psAs is per shear plane; choose shank or thread area from where the plane crosses.

Pt=Aspt is individual tension resistance.

Pnom=0.8Aspt is the nominal value used in the specified interaction expression.

Therefore, the “or” does not permit arbitrary selection.

Bolt bearing Pbb=dtppbb still requires separate connected-part bearing checks.

Weld q=0.7spw1000 is strength per millimetre of effective length, not total force.

Original Word page 2, including the correctly printed point-load exponent L³.

Original Word document p.2: deflection limits, connections and bolts.

The source uses lower-case span l and upper-case deflection Δ: full-span UDL Δ=5384wl4EI; midspan point load Δ=Pl348EI.

The cubic power in the point-load formula is correct.

This lesson writes it as L3.

Common Table 5.1 limits: cantilevers length180; beams carrying plaster/brittle finishes span360; other beams span200.

Bolt shear resistance Ps=psAs; tension resistance Pt=Aspt, or use the following in the specified interaction expression: Pnom=0.8Aspt; bolt bearing Pbb=dtppbb.

Original fillet-weld expression Strength=0.7×(leg length)×pw×10−3kNmm; Strength means resistance per millimetre of effective length, leg length is the weld leg entered in millimetres, and pw is measured in Nmm2 is substituted.Open full-size image

Prediction and explained answer.

A 6mm S355/Class 42 fillet has 120mm effective length.

What direct force can it carry?

Answer and reasoning

q=0.7×6×2501000=1.05kNmm; resistance=qL=1.05×120=126kN, subject to detailing and parent-metal checks.

Mechanism detailsFrom fillet leg to effective throat1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. An equal-leg fillet between perpendicular plates has an approximately right-triangular section.
  2. For this geometry, throat .

    It is shorter than the leg.

  3. Effective resisting area = .

    With here, capacity per length is .

  4. Use the course end allowances, minimum size and length rules; increasing the geometric length alone does not resolve every detailing check.

Mechanism detailsSee stiffness and deflection6 concepts · 12 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Use the specified SLS load, span and support arrangement.

    The demonstrator has a full-span UDL.

  2. The loaded beam bends.

    The deformation is exaggerated so its shape can be seen.

  3. For a simply supported full-span UDL, .

    Double L with w, E and I unchanged: δ becomes 16 times as large.

  4. The readout uses , and .

    Select the finish/support-specific limit from the original table.