Plain-English steelwork glossary
Read the unfamiliar word just before you need it.
Symbols are local to a formula: for example may mean bolt diameter in a connection and clear web depth in a section table.
Check the definition and unit at the point of use.
Action / load
An applied force, pressure or moment.
Keep characteristic and factored values distinct.
Mechanism detailsFrom characteristic to design load
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
G is permanent load; Q is imposed load.
A surface load and a line load also have different units.
This illustration uses the course gravity case .
Other combinations in the original text retain their own factors.
- For illustrative , the separate load contributions show what changes when Q increases.
Do not carry this ULS total automatically into deflection.
Follow the stated SLS load case.
Axial force, or
Force along the member axis, in or .
Compression is in the column equations.
Mechanism detailsEffective length and buckling axes
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- A column can bow sideways before its section reaches the crushing resistance.
- Each axis has its own radius of gyration and restraint spacing.
, with compatible length units.
A tie affects only the directions it actually restrains.
Select each buckling curve and compressive strength before forming Pc.
The governing axis is determined by resistance, not slenderness alone.
Bearing
Local contact pressure where a bolt pushes against a hole or a support pushes into a beam web.
It is not the same mechanism as shear.
Mechanism detailsBearing and the remaining ligament
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- Force transfers through contact between bolt and connected plate.
The plate around the hole carries bearing stress.
Bolt bearing and plate bearing are separate checks.
A short ligament can tear out towards the end.
The direction of force determines the relevant edge.
- Evaluate every specified bearing and ligament bound for each layer and retain the smallest applicable resistance.
Bending moment,
Turning effect at a cut, force×perpendicular distance, in or .
Internal moment sign must follow one convention.
Mechanism detailsCompression and tension across a section
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- For sagging, the top flange is in compression and the bottom in tension; hogging reverses this.
- Elastic bending stress varies with distance from the neutral axis: .
- The section class governs whether elastic, plastic or effective properties may be used.
Use the shear at the section under examination.
The largest shear elsewhere is not automatically coexistent.
Block shear
Failure of a block bounded by shear paths along bolt lines and a tension path across the end.
Mechanism detailsSeparate the block-shear paths
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- A block containing the connection can detach from the surrounding plate.
- The paths parallel to the applied force carry shear.
- The closing path across the end of the block carries tension.
Use the specified gross/net deductions and resistance expression.
This is different from a single straight net-section fracture.
Buckling
Instability of a compressed member or plate.
It can occur before material yield.
Restraint and slenderness matter.
Mechanism detailsEffective length and buckling axes
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- A column can bow sideways before its section reaches the crushing resistance.
- Each axis has its own radius of gyration and restraint spacing.
, with compatible length units.
A tie affects only the directions it actually restrains.
Select each buckling curve and compressive strength before forming Pc.
The governing axis is determined by resistance, not slenderness alone.
Centroid
Area-weighted centre of a section, or length-weighted centre of a uniform line-weld group.
Measure eccentricity from the centre appropriate to the model.
Mechanism detailsA weld group is a set of lines
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
Use line lengths for centroid weighting.
Line second moments have units .
Add the parallel-axis terms.
Direct force per length is .
The eccentric moment adds tangential flow proportional to distance from the centroid.
- Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.
Characteristic load, and
The supplied unfactored permanent and imposed loads.
Apply the stated combination to obtain design actions.
Mechanism detailsFrom characteristic to design load
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
G is permanent load; Q is imposed load.
A surface load and a line load also have different units.
This illustration uses the course gravity case .
Other combinations in the original text retain their own factors.
- For illustrative , the separate load contributions show what changes when Q increases.
Do not carry this ULS total automatically into deflection.
Follow the stated SLS load case.
Class 1 / 2 / 3 / 4
Plastic / compact / semi-compact / slender classification in the supplied notation; determines available section resistance.
Mechanism detailsWhy thin elements buckle locally
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- The flange outstand and web have different widths, thicknesses and edge support conditions.
- A thinner plate can wrinkle locally before the complete member loses stability.
Class 1 allows plastic rotation.
Class 2 reaches plastic resistance.
Class 3 reaches elastic resistance.
Class 4 requires effective properties.
Check every relevant compression element with the supplied limits and stress distribution.
The deformation shown is qualitative.
Compression flange
The flange shortened by bending: usually top under sagging, bottom under hogging.
Its lateral restraint affects LTB.
Mechanism detailsA beam bends sideways and twists
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- For the illustrated sagging beam the top flange is compressed.
- The unrestrained compression flange can move sideways while the complete cross-section twists.
Only effective restraints divide the member into unbraced segments.
They do not automatically add vertical supports.
Use the segment effective length, section properties and matching moment factor.
This is an exaggerated mode shape, not a calculated displacement.
Dead load,
Permanent load: slab, finishes and member self-weight where applicable.
A mass in must first become force per length.
Mechanism detailsFrom characteristic to design load
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
G is permanent load; Q is imposed load.
A surface load and a line load also have different units.
This illustration uses the course gravity case .
Other combinations in the original text retain their own factors.
- For illustrative , the separate load contributions show what changes when Q increases.
Do not carry this ULS total automatically into deflection.
Follow the stated SLS load case.
Deflection, or
Displacement of the beam, normally .
Strength and deflection are separate checks.
Mechanism detailsSee stiffness and deflection
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
Use the specified SLS load, span and support arrangement.
The demonstrator has a full-span UDL.
The loaded beam bends.
The deformation is exaggerated so its shape can be seen.
For a simply supported full-span UDL, .
Double L with w, E and I unchanged: δ becomes 16 times as large.
The readout uses , and .
Select the finish/support-specific limit from the original table.
Design strength,
Thickness-dependent steel strength in .
It is not always the number in the steel grade name.
Mechanism detailsRead a table without losing the keys
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- Name the required property: material strength, section property, buckling strength or a moment factor.
- Keep section size, steel grade, thickness band, curve and axis as separate lookup keys.
, and require different conversion powers.
Do not use adjacent columns interchangeably.
Use bracketing rows within the same valid column.
The original page remains the source of all table values.
Ductility
Ability to deform substantially before fracture; useful for redistribution and warning before failure.
Mechanism detailsElasticity, yielding and ductility
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
Stress is force divided by area.
Strain measures change in length relative to original length.
Before yielding, stress is approximately .
E controls the elastic slope.
Further strain includes permanent deformation.
Higher yield strength does not by itself increase E.
Strength, stiffness and ductility answer different questions.
This schematic is not a measured stress–strain curve.
Eccentricity,
Perpendicular distance between force line and reference centre/pivot.
Creates moment .
It is not necessarily the dimension written beside the load arrow.
Mechanism detailsEccentric reactions and stiffness sharing
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- A beam reaction can act away from the column centre even at a nominally pinned beam connection.
.
Opposing reactions can cancel part of the signed moment, while both still add compression.
- The course simple model distributes the joint moment in proportion to of the columns above and below.
Equal relevant stiffness gives half each.
A roof joint with no upper column is a different case.
Effective area,
Area permitted in the resistance formula after relevant hole, shear-lag or slender-element rules.
Not interchangeable with gross area .
Mechanism detailsSubtract holes on the failure path
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- Gross area counts the complete plate width and thickness.
- The highlighted transverse path passes through the bolt holes.
For the straight illustrative path, .
Staggered paths require their specified correction.
Net area is not always effective area.
Include the course’s strength ratio or shear-lag rule when applicable.
Effective length,
Length representing a stated buckling restraint condition.
Flexural, LTB and local-web effective lengths are different quantities.
Mechanism detailsEffective length and buckling axes
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- A column can bow sideways before its section reaches the crushing resistance.
- Each axis has its own radius of gyration and restraint spacing.
, with compatible length units.
A tie affects only the directions it actually restrains.
Select each buckling curve and compressive strength before forming Pc.
The governing axis is determined by resistance, not slenderness alone.
Elastic modulus,
Elastic section modulus, .
Measures bending resistance at first yield.
In this course is elastic and is plastic.
Mechanism detailsExplore section geometry and axes
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
The flanges are the wide plates.
The web connects them.
Rotate the I-section to see both.
- The same section has different stiffness and resistance about its two principal axes.
I controls elastic curvature.
is elastic section modulus.
Plastic modulus S comes from plastic stress blocks.
Nominal section labels are not every actual dimension.
Keep the row, axis and units together.
End / edge distance
Distance from hole centre to a plate boundary.
End distance is along load transfer; edge distance is transverse.
Mechanism detailsBolt centres, holes and edges
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
Hole diameter d₀ differs from nominal bolt diameter d.
Net-section deductions use the specified hole.
- Pitch runs along the load direction; gauge measures spacing across rows.
End and edge distances start at the hole centre.
The remaining ligament starts at the hole boundary.
- Minimum spacing, edge distances, grip and plate thickness come from the specified rules, not this scaled illustration.
Fillet leg, / throat,
Leg is the visible side of an equal-leg weld triangle; effective throat for the course fillet.
Mechanism detailsFrom fillet leg to effective throat
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- An equal-leg fillet between perpendicular plates has an approximately right-triangular section.
For this geometry, throat .
It is shorter than the leg.
Effective resisting area = .
With here, capacity per length is .
- Use the course end allowances, minimum size and length rules; increasing the geometric length alone does not resolve every detailing check.
Flange, and
Wide outer plate of I/H section.
is full flange width, flange thickness.
The in is the applicable outstand width.
Mechanism detailsExplore section geometry and axes
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
The flanges are the wide plates.
The web connects them.
Rotate the I-section to see both.
- The same section has different stiffness and resistance about its two principal axes.
I controls elastic curvature.
is elastic section modulus.
Plastic modulus S comes from plastic stress blocks.
Nominal section labels are not every actual dimension.
Keep the row, axis and units together.
Gauge / pitch
Transverse spacing between fastener lines / longitudinal spacing along a line.
Both are measured between centres.
Mechanism detailsBolt centres, holes and edges
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
Hole diameter d₀ differs from nominal bolt diameter d.
Net-section deductions use the specified hole.
- Pitch runs along the load direction; gauge measures spacing across rows.
End and edge distances start at the hole centre.
The remaining ligament starts at the hole boundary.
- Minimum spacing, edge distances, grip and plate thickness come from the specified rules, not this scaled illustration.
Gross area,
Full cross-sectional steel area before deductions, .
Mechanism detailsSubtract holes on the failure path
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- Gross area counts the complete plate width and thickness.
- The highlighted transverse path passes through the bolt holes.
For the straight illustrative path, .
Staggered paths require their specified correction.
Net area is not always effective area.
Include the course’s strength ratio or shear-lag rule when applicable.
Imposed load,
Variable occupancy/use load.
Called live load in many questions.
The imposed-load deflection check uses the specified unfactored value.
Mechanism detailsSee stiffness and deflection
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
Use the specified SLS load, span and support arrangement.
The demonstrator has a full-span UDL.
The loaded beam bends.
The deformation is exaggerated so its shape can be seen.
For a simply supported full-span UDL, .
Double L with w, E and I unchanged: δ becomes 16 times as large.
The readout uses , and .
Select the finish/support-specific limit from the original table.
Interaction
An equation combining utilization from simultaneous actions.
Its permitted limit depends on the actual equation.
Mechanism detailsCombined actions share resistance
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- Shear and tension, or compression and bending, must refer to the same bolt or checked section.
- Divide every action by the resistance prescribed for that term.
The bars illustrate a linear sum only.
Bolt interaction can have a different limit and individual checks; retain the original expression.
A pass in one interaction does not prove all failure modes pass.
The complete calculation below checks the specified interaction and the separate failure modes.
Lateral restraint
Attachment preventing sideways motion of the relevant flange.
Does not automatically provide vertical support.
Mechanism detailsA beam bends sideways and twists
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- For the illustrated sagging beam the top flange is compressed.
- The unrestrained compression flange can move sideways while the complete cross-section twists.
Only effective restraints divide the member into unbraced segments.
They do not automatically add vertical supports.
Use the segment effective length, section properties and matching moment factor.
This is an exaggerated mode shape, not a calculated displacement.
Lateral-torsional buckling, LTB
A bending member moves sideways and twists.
Weak-axis radius and torsional properties enter the resistance calculation.
Mechanism detailsA beam bends sideways and twists
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- For the illustrated sagging beam the top flange is compressed.
- The unrestrained compression flange can move sideways while the complete cross-section twists.
Only effective restraints divide the member into unbraced segments.
They do not automatically add vertical supports.
Use the segment effective length, section properties and matching moment factor.
This is an exaggerated mode shape, not a calculated displacement.
Line inertia, for a weld
Integral of squared distance along a weld line, in .
Do not confuse it with solid-section second moment of area in .
Mechanism detailsA weld group is a set of lines
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
Use line lengths for centroid weighting.
Line second moments have units .
Add the parallel-axis terms.
Direct force per length is .
The eccentric moment adds tangential flow proportional to distance from the centroid.
- Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.
Moment factor, or
Dimensionless factor representing the moment distribution for a specific member-instability check.
It does not reduce the actual section moment.
Mechanism detailsRead the moment shape within one segment
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- Moment ordinates must belong to the same effective unbraced segment.
- Same-side and reverse-curvature diagrams have different signed end ratios.
- The markers show ¼, ½ and ¾ of this segment, not of the entire beam.
LTB and column flexural factors are different.
Preserve their individual bounds and coefficient sets.
Net area,
Area left after holes across a candidate failure section; staggered paths require the supplied correction.
Mechanism detailsSubtract holes on the failure path
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- Gross area counts the complete plate width and thickness.
- The highlighted transverse path passes through the bolt holes.
For the straight illustrative path, .
Staggered paths require their specified correction.
Net area is not always effective area.
Include the course’s strength ratio or shear-lag rule when applicable.
Nominal bolt tension,
in the course interaction model.
Distinguish it from individual .
Mechanism detailsOut-of-plane bolt tension and prying
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- A bracket moment can create compression at the plate contact and tension in the bolt rows.
- The original assumed pivot/compression line determines each row distance.
Under the elastic row model, a farther tension row attracts more tension.
Direct shear may act simultaneously.
Flexible plates can add prying force.
Use nominal tension and interaction rules exactly as specified by the course.
Plastic modulus,
Plastic section modulus, , used for eligible Class 1/2 resistance with the prescribed cap.
Mechanism detailsExplore section geometry and axes
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
The flanges are the wide plates.
The web connects them.
Rotate the I-section to see both.
- The same section has different stiffness and resistance about its two principal axes.
I controls elastic curvature.
is elastic section modulus.
Plastic modulus S comes from plastic stress blocks.
Nominal section labels are not every actual dimension.
Keep the row, axis and units together.
Prying
Extra bolt tension caused by deformation/contact in the connected plate or flange.
A no-prying approximation needs its applicability conditions.
Mechanism detailsOut-of-plane bolt tension and prying
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- A bracket moment can create compression at the plate contact and tension in the bolt rows.
- The original assumed pivot/compression line determines each row distance.
Under the elastic row model, a farther tension row attracts more tension.
Direct shear may act simultaneously.
Flexible plates can add prying force.
Use nominal tension and interaction rules exactly as specified by the course.
Radius of gyration,
, a length.
A smaller gives larger slenderness for the same effective length.
Mechanism detailsExplore section geometry and axes
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
The flanges are the wide plates.
The web connects them.
Rotate the I-section to see both.
- The same section has different stiffness and resistance about its two principal axes.
I controls elastic curvature.
is elastic section modulus.
Plastic modulus S comes from plastic stress blocks.
Nominal section labels are not every actual dimension.
Keep the row, axis and units together.
Reaction
Force or moment supplied by a support to maintain equilibrium.
Transfer a secondary beam reaction as a primary-beam load.
Mechanism detailsBalance reactions and moments
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
This demonstrator is a simply supported 6 m beam with a 60 kN point load.
It is not the page’s original loading diagram.
.
Moving the load towards B increases .
.
The two upward reactions must sum to P.
With the load at midspan, .
End couples, UDLs and overhangs require their own equilibrium terms.
Second moment of area,
Integral of , in .
Controls elastic bending stiffness .
It is not an area or section modulus.
Mechanism detailsExplore section geometry and axes
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
The flanges are the wide plates.
The web connects them.
Rotate the I-section to see both.
- The same section has different stiffness and resistance about its two principal axes.
I controls elastic curvature.
is elastic section modulus.
Plastic modulus S comes from plastic stress blocks.
Nominal section labels are not every actual dimension.
Keep the row, axis and units together.
Section resistance, or
Capacity of the local cross-section.
Member buckling may impose an additional lower resistance.
Mechanism detailsCompression and tension across a section
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- For sagging, the top flange is in compression and the bottom in tension; hogging reverses this.
- Elastic bending stress varies with distance from the neutral axis: .
- The section class governs whether elastic, plastic or effective properties may be used.
Use the shear at the section under examination.
The largest shear elsewhere is not automatically coexistent.
Shear force,
Transverse force at a cut, in ; related to the slope of the BMD.
A point load causes a jump in the SFD.
Mechanism detailsBuild the shear and moment diagrams
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- For the illustrative 60 kN point load on a 6 m simply supported beam, balance the reactions before making a cut.
and before the point load.
Moment grows linearly.
Shear jumps down by P.
To its right, and .
For this case, moment is continuous and returns to zero at B.
A concentrated applied couple instead creates a moment jump.
Shear lag
Uneven tensile stress because only part of a section is directly connected.
The course reduces outstanding-leg contribution.
Mechanism detailsWhy a connected angle leg matters
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- Locate the connected leg, outstanding leg and centroid before using the table.
- Only the connected leg directly receives the fastener force.
The outstanding area may not become equally effective at the same section.
This motivates the effective-area rule.
Bolted, welded, single-angle and double-angle details can have different rules.
Preserve the formula attached to the original case.
Slenderness,
Dimensionless for member buckling.
Equivalent LTB slenderness additionally includes , and .
Mechanism detailsEffective length and buckling axes
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- A column can bow sideways before its section reaches the crushing resistance.
- Each axis has its own radius of gyration and restraint spacing.
, with compatible length units.
A tie affects only the directions it actually restrains.
Select each buckling curve and compressive strength before forming Pc.
The governing axis is determined by resistance, not slenderness alone.
Stiff bearing length,
Effective length of sufficiently stiff contact spreading a concentrated force into the web.
Not automatically the entire plate width.
Mechanism detailsSpread a concentrated force into the web
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- A concentrated reaction first enters through the bearing/contact region.
- The flange and root geometry spread the force before it enters the web.
- A wider effective bearing region can reduce local stress for the same force.
End distance, stiff bearing length and restraint conditions must come from the original question.
The illustrated dimensions explain the mechanism.
They do not replace the original question data.
Strut curve, ///
Buckling-resistance family selected by section type, thickness and axis before reading .
Mechanism detailsEffective length and buckling axes
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- A column can bow sideways before its section reaches the crushing resistance.
- Each axis has its own radius of gyration and restraint spacing.
, with compatible length units.
A tie affects only the directions it actually restrains.
Select each buckling curve and compressive strength before forming Pc.
The governing axis is determined by resistance, not slenderness alone.
Tributary width / area
Loaded slab region whose load reaches a beam or column under the stated one-way/load-path model.
Mechanism detailsFollow the floor load in 3D
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
The floor carries pressure in .
The highlighted strip belongs to one secondary beam.
Multiply pressure by tributary width: .
The illustration uses .
- A primary beam receives the secondary beam reaction at their connection, not a new full-span UDL.
Trace reactions down to columns and foundations.
Count each loaded area once.
ULS / SLS
Ultimate limit state: strength/stability.
Serviceability limit state: usable performance such as deflection.
Mechanism detailsTwo different design questions
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- ULS compares factored actions with the applicable resistance to yielding, rupture or instability.
- SLS checks movement, vibration or another specified use requirement.
A beam can be strong enough but deflect too much.
The two checks need their own loads and denominators.
A resistance pass cannot stand in for a serviceability pass.
Complete all requested checks.
Utilization
Demand divided by matching resistance, or the specified interaction sum.
State the actual allowable limit.
Mechanism detailsCombined actions share resistance
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- Shear and tension, or compression and bending, must refer to the same bolt or checked section.
- Divide every action by the resistance prescribed for that term.
The bars illustrate a linear sum only.
Bolt interaction can have a different limit and individual checks; retain the original expression.
A pass in one interaction does not prove all failure modes pass.
The complete calculation below checks the specified interaction and the separate failure modes.
Web, , and
Thin connecting plate of I/H section; web thickness, overall section depth, clear web depth.
Mechanism detailsExplore section geometry and axes
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
The flanges are the wide plates.
The web connects them.
Rotate the I-section to see both.
- The same section has different stiffness and resistance about its two principal axes.
I controls elastic curvature.
is elastic section modulus.
Plastic modulus S comes from plastic stress blocks.
Nominal section labels are not every actual dimension.
Keep the row, axis and units together.
Young’s modulus,
Elastic stress/strain slope, in this course.
Increasing grade does not change this course value.
Mechanism detailsElasticity, yielding and ductility
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
Stress is force divided by area.
Strain measures change in length relative to original length.
Before yielding, stress is approximately .
E controls the elastic slope.
Further strain includes permanent deformation.
Higher yield strength does not by itself increase E.
Strength, stiffness and ductility answer different questions.
This schematic is not a measured stress–strain curve.