STEELWORK / CON4334
Learn

Columns: buckling, eccentric reactions and combined forces

Diagrams, explanations and answers are presented in reading order. No playback or response is required.
All answers shownChinese–English terminology
Diagrams, explanations and answers are presented in reading order. No playback or response is required.

A compressed column can fail by local plate buckling, cross-section yielding, or overall member buckling.

Passing one does not prove the others.

This chapter follows LectureNotes/Ch 4_Column.pdf and the supplied HK2011 tables.

The numerical design scope is non-sway columns; sway theory is explained for recognition because it appears in the lectures.

Lecture examples are included immediately after the relevant concepts.

Expand an example to read its complete diagram, working, exam answer and self-check here.

1. Effective length belongs to an axis and a restraint model

Check buckling about both axes

Determine which buckling direction limits the compressed member.

Compare the outlines labelled Straight and Bowed. The dashed line beside Bowed marks its original straight reference.
Compare the outlines labelled Straight and Bowed. The dashed line beside Bowed marks its original straight reference.

Prediction, then explanation. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Calculate slenderness about each axis. Select each axis’s curve from section type and thickness. Then obtain and compare the two compressive resistances.

λx=LEx/rx,λy=LEy/ry,Pc=pcAg\lambda_x=L_{Ex}/r_x,\quad\lambda_y=L_{Ey}/r_y,\qquad P_c=p_cA_g

Effective lengths and radii use mm. pc is compressive strength in N/mm²; Ag is gross area in mm²; Pc is in N.

Scope. Do not select the governing axis using radius alone. Effective length and buckling curve can differ. A combined column also needs interaction checks.

Check and takeaway. A short-section yield resistance is not the same as long-member buckling resistance. Keep py and pc distinct.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why a long column can fail before crushing

Push a long thin ruler from both ends: it may bow sideways first.

Why a long column can fail before crushing — Push a long thin ruler from both ends: it may bow sideways first.

Sketch, not to scale; use the original dimensions.

  1. Find effective length and radius of gyration for each axis.
  2. Calculate slenderness for both directions.
  3. Use the appropriate buckling curve before forming resistance.

Remember: Compare the final resistances; slenderness alone may not identify the controlling axis.

Related concept and full method

Slenderness measures how long and weak a member is in a particular buckling direction: λ=Lᴱ/r.

Radius of gyration r=IA describes how far area lies from that bending axis.

Larger r gives a smaller slenderness.

A weak-axis tie can improve resistance without changing the steel section.

It only helps the direction it actually restrains.

LEx=KxLx;λx=LExrxLEy=KyLy;λy=LEyry
Idealized restraint pattern in Table 8.6Theoretical KRecommended K when ideal conditions are approximated
Both ends fixed against rotation and translation0.50.70
One end fixed, other pinned; translation prevented0.70.85
One end fixed, other rotation-fixed but translation-free1.01.20
Both ends pinned, translation prevented1.01.00
Fixed-free cantilever2.02.10
Source sixth pattern with partial rotational restraint and free translation at topNot specified1.5
Original Table8.6, Ch4 p.2: use the pictured end conditions and distinguish the theoretical and recommended rows.

Original Table 8.6, Ch 4 p.2: effective lengths of idealised columns.

Dashed lines indicate the buckled shape.

The six end-condition patterns, read left to right, and both rows of factors are reproduced in the table above.

From top to bottom, the legend means: rotation and translation fixed; rotation free and translation fixed; rotation fixed and translation free.

Both free; rotation partially restrained and translation free.

The source word “Transition” means translation here.

The page formula is λ=LEr, and LE=KL.

Open full-size image

Use the question’s explicitly given effective length if present.

Otherwise choose the source’s recommended factor for the modeled conditions, as the examples do.

Do not use textbook theoretical 0.5 where the worked course method uses 0.70.

Pin symbols indicate free rotation, not free lateral translation.

Keep r and L in the same units.

Prediction and explained answer.

A6 m pinned column has a midheight tie effective only against weak-axis buckling.

Find Lᴱx and Lᴱy.

Answer and reasoning

LxE=6m; LyE=3m.

Major-axis buckling can still extend over the full height.

Mechanism detailsEffective length and buckling axes1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

Mechanism detailsEffective length and buckling axes1 concept · 4 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

2. Select the buckling curve before reading compressive strength

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Move between two known values

The required slenderness lies between two table rows. Estimate the strength on the straight segment between those rows.

xy(70, 200)(74, 192)(80, 180)70748040% of input interval → 40% of output change
The marked position lies partway along the horizontal interval. Use the same fraction of the vertical change.

Prediction, then explanation. If the second strength is lower, moving toward that row must reduce the interpolated strength.

Subtract the lower input to find distance travelled. Divide by the input interval. Multiply that fraction by the output change.

f=x−x0x1−x0,y=y0+f(y1−y0)f=\frac{x-x_0}{x_1-x_0},\qquad y=y_0+f(y_1-y_0)

x is the required input. The two known pairs are (x₀, y₀) and (x₁, y₁). f has no unit.

Scope. Use one table, curve and strength column. This interpolation does not permit extrapolation or inventing an intermediate steel section.

Check and takeaway. Illustration: between strengths 200 and 180, a fraction of 0.4 gives 192 N/mm². The result lies between both endpoints.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A table lookup needs several keys

A table is like an address: knowing only the street is not enough.

A table lookup needs several keys — A table is like an address: knowing only the street is not enough.

Sketch, not to scale; use the original dimensions.

  1. Select the curve using section type, thickness and axis.
  2. Select the material-strength column.
  3. Bracket the slenderness and interpolate if required.

Remember: Do not jump between steel grades or extrapolate past supplied data.

Related concept and full method

First establish that the section is not slender.

For uniform compression the lecture checks flange bT≤13ε and web dt≤40ε, the semi-compact limits.

That permits the gross-area resistance Pc=Agpc.

It does not assert Class 1.

For combined bending and axial force, use the appropriate class limits before claiming plastic bending resistance.

Section; maximum thicknessCurve about x–xCurve about y–y
Rolled I; ≤40mmab
Rolled I; >40mmbc
Rolled H (UC); ≤40mmbc
Rolled H; >40mmcd
Welded I or H; ≤40mmbc
Welded I or H; >40mmbd

These rows are Table 8.7 in the Data File p.7.

The full source on Ch 4 p.4 also covers hollow sections, bars, angles, channels, cover plates and welded boxes.

The full table’s notes matter: thickness 40–50mm permits the specified averaging treatment; fabrication and cover-plate geometry can alter the curve.

Do not select a curve solely from steel grade.

Full Table8.7, Ch4 p.4: section type, maximum thickness, buckling-axis columns and special notes.

Full Table 8.7, Ch 4 p.4: section type, maximum thickness, buckling axis and special notes.

Each curve pair below is in the order x–x/y–y; thickness boundaries follow the source table.

Hot-finished structural hollow sections in steel above S460, or hot-finished seamless hollow sections: a0/a0.

Hot-finished hollow sections in steel below S460: a/a.

These two source rows say “above” and “below”.

Neither explicitly assigns exactly S460, so do not invent an equality boundary.

Cold-formed hollow sections with longitudinal or spiral welds: c/c.

Hot-rolled I-sections: thickness ≤40mm uses a/b; >40mm uses b/c.

Hot-rolled H-sections: for the same two thickness intervals, use respectively b/c and c/d.

Welded I/H-sections: use respectively b/c and b/d; also see note 2.

Hot-rolled sections with welded flange cover plates: select the row using the Figure 8.4 ratio UB.

When 0.25<UB<0.80: for I-sections in the two thickness intervals above, use respectively a/b and b/c.

For H-sections, use respectively b/c and c/d.

When UB≥0.80: for I/H-sections, use respectively b/a and c/b.

When UB≤0.25: for I/H-sections, use respectively b/c and b/d.

Welded box sections: for the two thickness intervals above, use respectively b/b and c/c; also see note 3.

Round, square or flat bars: use respectively b/b and c/c.

Hot-rolled angles, channels and tees; two hot-rolled sections connected by lacing, battens or back to back; and built-up hot-rolled sections: for either axis, use c.

Note 1: for thickness 40mm to 50mm, for the same relevant py, average the values for thickness not exceeding 40mm and thickness exceeding 40mm of pc.

Note 2: for welded I/H-section flanges machine flame-cut without subsequent edge grinding or machining, when buckling about the y–y axis, flange thickness not exceeding 40mm may use curve b; above that thickness, use c.

Note 3: “welded box sections” includes boxes assembled from plates or hot-rolled sections with all longitudinal welds near the corners, but excludes boxes with longitudinal stiffeners.

Note 4: the source permits curves from other recognised codes when differences in load/material partial factors are addressed and the curves are calibrated against Tables 8.8(a₀), (a) to (h).

The Table 8.8 footnote also applies.

This does not supply numerical values that can simply be mixed with the course tables.Open full-size image

  1. Identify section family and fabrication, maximum thickness and buckling axis; choose its curve.
  2. Confirm pᵧ from grade and thickness.

    Select that strength column within the appropriate Table 8.8 curve.

  3. Calculate λ for that axis and locate bracketing rows.

    Interpolate pc.

    Do not extrapolate beyond supplied tables.

  4. Compute Pcx=Agpcx and Pcy=Agpcy.

    Use the smaller for the flexural compression check.

If A uses cm2,pc uses Nmm2: Pc(kN)=A×100×pc1,000=Apc10

Check both axes even if rᵧ is smaller: different effective lengths and different curves may change which controls.

Data File p.8 supplies S355 curves only over its printed rows.

The lecture and 2023 extra data contain further tables.

Choose a supplied applicable table and cite it.

Do not invent a value from the trend.

Column example 1: a pinned column in axial compression

Select a Grade S355 UC for a 6m column pinned at both ends, carrying a design axial compression of 2,500kN. Check the selected section’s compression resistance.

Original source: LectureNotes/Ch 4_Column.pdf — p. 21, p. 22.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

Keep load categories separate

A floor carries permanent material and changing occupancy loads. Find the design load for the stated check.

The two boxes show G and Q with their separate factors. The plus sign joins their factored values.
The two boxes show G and Q with their separate factors. The plus sign joins their factored values.

Prediction, then explanation. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

First convert mass to weight where required. Next collect G and Q in compatible units. Apply the combination specified by the course problem.

Wu=1.4G+1.6QW_u=1.4G+1.6Q

G is characteristic dead load; Q is characteristic imposed load. Wu is the design load for this course gravity combination.

Scope. This combination is not universal. Use the specified service load for deflection and the stated factors for other standards or cases.

Check and takeaway. Illustration: G = 10 kN and Q = 5 kN give 22 kN. Factoring their sum by one guessed factor loses the distinction.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Use the property for the physical question

A section table contains several numbers. Choose the property that matches the calculation and bending axis.

Read the three labels beside the I-section: I describes geometric stiffness, Z elastic section modulus and S plastic section modulus.
Read the three labels beside the I-section: I describes geometric stiffness, Z elastic section modulus and S plastic section modulus.

Prediction, then explanation. Moving equal area away from an axis increases I about that axis. It does not increase total area.

Each small area contributes its area multiplied by squared distance. Sum those contributions to obtain I.

I=∫y2 dA,r=I/AI=\int y^2\,dA,\qquad r=\sqrt{I/A}

I is second moment of area in mm⁴. y is distance from the chosen axis in mm. A is area in mm². r is radius of gyration in mm.

Scope. Z is elastic section modulus; S is plastic section modulus in this course. Neither is interchangeable with I.

Check and takeaway. A nominal section designation is a row identifier. Use the actual dimensions and units in that exact row.

Apply the reasoning to this section’s data and conditions

InputSource and meaning
Design load

Given Fc=2,500kN, already factored.

No dead/imposed breakdown is needed.

RestraintsPinned-pinned, translation prevented at ends; Table 8.6 gives K=1 in both axes.
Selected rowData File p.11, 305×305×118 UC: flange T=18.7mm, bT=8.22, dt=20.6, rx=13.6cm, ry=7.77cm, A=150cm2.
Strength and curves

S355,T=18.7, giving py=345Nmm2.

Hot-rolled H-section, T≤40, so x axis uses curve b; y axis uses curve c.

Why this method applies

A strong cross-section can belong to an unstable member

A column carries axial compression and bending. Explain why more than one check is required.

The three boxes name separate checks: Section, Flexural and LTB. The bottom caption explains that passing one does not pass the others.
The three boxes name separate checks: Section, Flexural and LTB. The bottom caption explains that passing one does not pass the others.

Prediction, then explanation. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Separate cross-section, flexural-buckling and LTB interaction equations. Use each equation’s own denominators and first-order or amplified moments.

AgpyA_g p_y is a section axial resistance. AgpcA_g p_c is a member compression resistance. Elastic pyZp_y Z and prescribed McM_c are different bending denominators.

Scope. Preserve the course barred-moment definitions and Eq. 8.81 convention. Do not substitute plastic moduli into an elastic denominator.

Check and takeaway. Report each requested utilisation and the governing check. The largest properly calculated ratio identifies the closest limit.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

There is no stated bending moment.

Therefore, the core numerical task is axial member buckling.

First ensure the local plates are not slender, allowing gross area.

Then calculate both axis slendernesses and select the correct curve for each.

The area alone is not enough: a long weak column can buckle well before reaching A𝗀pᵧ.

1. Choose a section and confirm its strength

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

The lecturer selects a trial 305×305×118 UC.

Its nominal mass 118kgm is part of the section designation.

The strength calculation uses the tabulated gross area 150cm2.

The flange thickness is 18.7mm, falling within the S355 thickness band 16<T≤40mm.

py=345Nmm2Ag=150cm2×100=15,000mm2Gross-section squash resistance: Agpy=15,000×3451,000=5,175kN

5,175kN exceeds the load but is not the member resistance.

Proceed to local-slenderness and overall-buckling checks.

Mechanism detailsEffective length and buckling axes2 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

2. Establish a non-slender section

Find which plate buckles first

Before using plastic bending resistance, check whether the flange and web can sustain the required stress distribution.

The short waves are local plate buckling. They differ from sideways movement of the whole member.
The short waves are local plate buckling. They differ from sideways movement of the whole member.

Prediction, then explanation. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Calculate the flange and web ratios separately. Compare each with the limits for its stress condition. The worse class governs.

ε=275/py\varepsilon=\sqrt{275/p_y}

py is the design yield strength in N/mm². ε is a dimensionless scale used in the supplied classification limits.

Scope. Pure bending and uniform compression use different web limits. Class 2 allows plastic resistance but not the Class 1 rotation capability.

Check and takeaway. A Class 1 web and Class 2 flange give a Class 2 section. Do not average the class numbers.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A thin part can wrinkle first

A thin plate may wrinkle before the whole steel member reaches its intended resistance.

A thin part can wrinkle first — A thin plate may wrinkle before the whole steel member reaches its intended resistance.

Sketch, not to scale; use the original dimensions.

  1. Check flange and web slenderness using their own definitions.
  2. Compare each ratio with the correct class limits.
  3. The element with the more restrictive class determines the section class.

Remember: Bending limits and uniform-compression limits are different.

Related concept and full method

ε=275345=0.892805Semi-compact limit for a uniformly compressed flange: 13ε=11.6065bT=8.22<11.6065Semi-compact limit for a uniformly compressed web: 40ε=35.7122dt=20.6<35.7122Both pass; the section is non-slender and the gross-section compression-resistance method applies.

This establishes Class 3 or better, not necessarily a plastic flange.

The pure-compression example does not need plastic bending resistance; checking the non-slender boundary is sufficient for its stated method.

Mechanism detailsWhy thin elements buckle locally1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The flange outstand and web have different widths, thicknesses and edge support conditions.
  2. A thinner plate can wrinkle locally before the complete member loses stability.
  3. Class 1 allows plastic rotation.

    Class 2 reaches plastic resistance.

    Class 3 reaches elastic resistance.

    Class 4 requires effective properties.

  4. Check every relevant compression element with the supplied limits and stress distribution.

    The deformation shown is qualitative.

3. Calculate slenderness about both axes

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why a long column can fail before crushing

Push a long thin ruler from both ends: it may bow sideways first.

Why a long column can fail before crushing — Push a long thin ruler from both ends: it may bow sideways first.

Sketch, not to scale; use the original dimensions.

  1. Find effective length and radius of gyration for each axis.
  2. Calculate slenderness for both directions.
  3. Use the appropriate buckling curve before forming resistance.

Remember: Compare the final resistances; slenderness alone may not identify the controlling axis.

Related concept and full method

LEx=LEy=1×6,000=6,000mmrx=13.6cm=136mm;ry=7.77cm=77.7mmλx=6,000136=44.117647λy=6,00077.7=77.220077

The smaller weak-axis radius makes its slenderness much larger.

Still read both curves rather than assuming the larger slenderness by itself proves which resistance controls.

Mechanism detailsEffective length and buckling axes1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

4. Read and interpolate the two compressive strengths

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: Move between two known values. If the second strength is lower, moving toward that row must reduce the interpolated strength.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A table lookup needs several keys

A table is like an address: knowing only the street is not enough.

A table lookup needs several keys — A table is like an address: knowing only the street is not enough.

Sketch, not to scale; use the original dimensions.

  1. Select the curve using section type, thickness and axis.
  2. Select the material-strength column.
  3. Bracket the slenderness and interpolate if required.

Remember: Do not jump between steel grades or extrapolate past supplied data.

Related concept and full method

Table 8.7, rolled H section with maximum thickness 18.7≤40mm: x–x uses 8.8(b), y–y uses 8.8(c).

In each use the pᵧ=345 column of Data File p.8.

Major axis, curve b: 44 row gives 302,46 row gives 298Nmm2. Interpolation fraction: 44.117647−4446−44=0.058824pc=302+0.058824×(298−302)=301.764706Nmm2Minor axis, curve c: 76 row gives 196,78 row gives 191Nmm2. Interpolation fraction: 77.220077−7678−76=0.610039pc=196+0.610039×(191−196)=192.949807Nmm2

The source rounds these to 302 and 193Nmm2.

The minor axis has the smaller pc and controls for the same area.

Mechanism detailsEffective length and buckling axes2 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

5. Form resistances and conclude

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

Pcx=15,000×301.7647061,000=4526.471kNPcy=15,000×192.9498071,000=2894.247kNPc=min(Pcx,Pcy)=2894.247kNFc=2,500<Pc; adequate under the specified axial compression. Utilisation: 2,5002894.247=0.8638

Using the lecturer’s rounded 193 gives 150×19310=2,895kN, agreeing with the original answer.

The governing failure mode is minor-axis overall buckling, not yielding of the full gross area.

Mechanism detailsEffective length and buckling axes1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

Result and concise exam wording

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

Select S355 305×305×118 UC; T=18.7, giving py=345.

bT=8.22<13ε,dt=20.6<40ε, non-slender.LxE=LyE=6m,λx=44.1176,λy=77.2201.

Curves b/c give respectively pcx=301.765, pcy=192.950Nmm2.

Pc=2,894.247kN>2,500kN, adequate.

Rounded source result 2,895kN.

Misconceptions and checks

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

  • Do not use 355Nmm2 solely because the steel is S355.
  • Do not halve the effective length just because both ends are supported.
  • Do not use the same strut curve for both UC axes.
  • Do not treat the lower reaction arrow as a second applied load.

How the method transfers to a new variant

Vertical bending can trigger sideways motion

A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.

The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.
The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.

Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.

λ=LE/ry,Mb=pbSx  (Class 1/2),mLTMmax≤Mb\lambda=L_E/r_y,\qquad M_b=p_bS_x\;\text{(Class 1/2)},\qquad m_{LT}M_{max}\le M_b

LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.

Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.

Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.

A force couple carries moment

Separate the force couple used to carry moment from the force used to carry web shear.

The flange forces act in opposite directions. Their separation z gives the lever arm. The web arrow represents shear.
The flange forces act in opposite directions. Their separation z gives the lever arm. The web arrow represents shear.

Prediction, then explanation. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Moment is force multiplied by perpendicular separation. Divide the required moment by the specified separation to obtain each couple force.

F=M/zF=M/z

M is moment in kN·mm; z is the specified force-line separation in mm; F is force in kN.

Scope. Use the lever arm defined by the source model. Do not silently replace it with overall section depth or another geometric distance.

Check and takeaway. Check flange welds for the couple forces and web welds for the stated shear model. Both force paths need a satisfactory detail.

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Apply the reasoning to this section’s data and conditions

  1. Identify axial load, any moments, actual length and restraints in each axis.
  2. Choose/read a section and confirm strength from the actual thickness.
  3. Check the appropriate flange and web local-slenderness limits.
  4. Find λx and λy separately.

    Select each axis curve and interpolate pc.

  5. Calculate both axial resistances and identify the governing axis.
  6. If moments exist, complete section, flexural and axial/LTB interactions using their own capacities and moment definitions.

Prediction with explained answer

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Invented variant: the same column now carries 3,000kN design axial compression, with the same length and restraints.

Does it pass?

Answer and reasoning

No. Non-slender classification and buckling resistance are unchanged.

Utilisation=3,0002,894.247≈1.0365>1.

The gross squash resistance 5,175kN cannot override the member buckling failure.

Mechanism detailsEffective length and buckling axes2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

Column example 2: a weak-axis tie permits a lighter section

Repeat the 2,500kN axial-column design with a 6m pinned column and an effective midheight tie against weak-axis buckling. Select and check a Grade S355 UC.

Original source: LectureNotes/Ch 4_Column.pdf — p. 23, p. 24.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

InputOrigin
Axial forceGiven 2,500kN design compression.
Direction of tieQuestion states weak direction: shorten y-axis buckling length only.
Trial sectionData File p.11, 254×254×73 UC: T=14.2mm, bT=8.96, dt=23.3, rx=11.1cm, ry=6.48cm, A=93.1cm2.
Tablespᵧ355 because T≤16; rolled H≤40 uses curves b/c.

Why this method applies

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Use the same mechanism: Use the property for the physical question. Moving equal area away from an axis increases I about that axis. It does not increase total area.

Apply the reasoning to this section’s data and conditions

Compare this to Example 1: restraints can be as important as area.

The weak-axis tie reduces its unbraced length from 6 to 3m.

A smaller column is now possible, but after changing section both radii, the area and the thickness-dependent strength must be reread.

Do not reuse Example 1’s section properties.

1. Set each effective length

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why a long column can fail before crushing

Push a long thin ruler from both ends: it may bow sideways first.

Why a long column can fail before crushing — Push a long thin ruler from both ends: it may bow sideways first.

Sketch, not to scale; use the original dimensions.

  1. Find effective length and radius of gyration for each axis.
  2. Calculate slenderness for both directions.
  3. Use the appropriate buckling curve before forming resistance.

Remember: Compare the final resistances; slenderness alone may not identify the controlling axis.

Related concept and full method

Major axis has no effective intermediate tie: LEx=6,000mmMinor axis has a mid-height tie: LEy=3,000mmEach of the two segments has length 3m and carries the full 2,500kN axial force.

A horizontal positional restraint suppresses a buckling displacement.

It does not support half the vertical load or create a new 2,5002kN compression case.

Mechanism detailsEffective length and buckling axes1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

2. Trial 254×254×73 UC

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Use the same mechanism: Use the property for the physical question. Moving equal area away from an axis increases I about that axis. It does not increase total area.

Apply the reasoning to this section’s data and conditions

T=14.2mm≤16→py=355Nmm2Ag=93.1cm2=9,310mm2rx=11.1cm=111mm;ry=6.48cm=64.8mm

These values come from the same exact section row on Data File p.11.

This lighter trial is the one selected in the lecture.

Mechanism detailsEffective length and buckling axes3 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

3. Check local slenderness

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Apply the reasoning to this section’s data and conditions

ε=275355=0.88014113ε=11.4418;bT=8.96<11.441840ε=35.2056;dt=23.3<35.2056Flange and web are both non-slender in uniform compression.

Mechanism detailsWhy thin elements buckle locally1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The flange outstand and web have different widths, thicknesses and edge support conditions.
  2. A thinner plate can wrinkle locally before the complete member loses stability.
  3. Class 1 allows plastic rotation.

    Class 2 reaches plastic resistance.

    Class 3 reaches elastic resistance.

    Class 4 requires effective properties.

  4. Check every relevant compression element with the supplied limits and stress distribution.

    The deformation shown is qualitative.

4. Slenderness for the tied and untied directions

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

λx=6,000111=54.054054λy=3,00064.8=46.296296

Now λx exceeds λy.

That alone does not prove the x axis controls because its curve b is more favourable than the weak-axis curve c.

Mechanism detailsEffective length and buckling axes1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

5. Interpolate each curve

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Use the same mechanism: Move between two known values. If the second strength is lower, moving toward that row must reduce the interpolated strength.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A value between two table rows

Move the same fraction of the way across both number ranges.

A value between two table rows — Move the same fraction of the way across both number ranges.

Sketch, not to scale; use the original dimensions.

  1. Choose the correct table, curve and strength column first.
  2. Find how far your input lies between the two rows.
  3. Apply that fraction to the change between their answers.

Remember: Teaching example: halfway between outputs 100 and 80 gives 90.

Related concept and full method

Use Table 8.8(b), pᵧ355 for x and Table 8.8(c), pᵧ355 for y.

Major axis: 54 row gives 288,56 row gives 283Nmm2. Interpolation fraction: 54.054054−5456−54=0.027027pc=288+0.027027×(283−288)=287.864865Nmm2Minor axis: 46 row gives 286,48 row gives 280Nmm2. Interpolation fraction: 46.296296−4648−46=0.148148pc=286+0.148148×(280−286)=285.111111Nmm2

Despite its smaller slenderness, the weak axis gives the slightly smaller strength.

The source values 288 and 285Nmm2 are rounded representations.

Mechanism detailsEffective length and buckling axes3 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

6. Check the controlling resistance

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

Pcx=9,310×287.8648651,000=2680.022kNPcy=9,310×285.1111111,000=2654.384kNPc=2654.384kN>2,500kNAdequate. Utilisation: 2,5002654.384=0.9418

The original rounds pc to 285, giving 93.1×28510=2,653.35kN, printed 2,653kN.

The exact interpolation gives 2,654.384kN.

The tie makes the 73kgm trial adequate where the untied example used 118kgm.

This conclusion assumes the tie provides the stated effective restraint; tie design itself is not part of this question.

Mechanism detailsEffective length and buckling axes1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

Result and concise exam wording

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

Use S355 254×254×73 UC,py=355; under the 13ε, 40ε limits, it is non-slender.LxE=6m, LyE=3m; λx=54.0541, λy=46.2963.

Curves b/c give pcx=287.865, pcy=285.111Nmm2.

Pc=2,654.384kN>2,500, adequate.

Rounded source resistance 2,653kN.

Misconceptions and checks

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

  • The tie changes only its effective buckling direction.
  • Use the full axial force in both 3m portions.
  • Compare actual pc values, not slenderness alone.
  • Reclassify after selecting a lighter section.

How the method transfers to a new variant

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: A force couple carries moment. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Apply the reasoning to this section’s data and conditions

  1. Identify axial load, any moments, actual length and restraints in each axis.
  2. Choose/read a section and confirm strength from the actual thickness.
  3. Check the appropriate flange and web local-slenderness limits.
  4. Find λx and λy separately.

    Select each axis curve and interpolate pc.

  5. Calculate both axial resistances and identify the governing axis.
  6. If moments exist, complete section, flexural and axial/LTB interactions using their own capacities and moment definitions.

Prediction with explained answer

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Invented variant: remove the weak-axis tie but retain 254×254×73 UC.

Find the weak-axis slenderness and estimate its supplied-table resistance.

Answer and reasoning

λy=6,00064.8=92.59259.

Curve c,pᵧ355: row 92 gives 158 and 94 gives 153, so pc=158+(0.592592)(153−158)=156.5185Nmm2.

Pcy=9,310×156.51851,000=1,457.187kN, much less than 2,500.

The untied version fails.

Mechanism detailsEffective length and buckling axes2 concepts · 3 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

Mechanism detailsEffective length and buckling axes3 concepts · 17 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

3. Cross-section capacity: axial force consumes some of the same resistance

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Two simultaneous actions use one component

Check a component that carries shear and tension, or compression and bending, at the same time.

The bolt receives two labelled arrows: tension and shear. The caption requires both individual checks and the combined check.
The bolt receives two labelled arrows: tension and shear. The caption requires both individual checks and the combined check.

Prediction, then explanation. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

First apply the individual checks. Next use the exact combined equation and its definitions. Keep demands from the same load case.

FsPs+FtPnom≤1.4\frac{F_s}{P_s}+\frac{F_t}{P_{nom}}\le1.4

This is the course bolt interaction rule. Fs and Ft are bolt demands; Ps and Pnom are their specified resistance denominators.

Scope. The 1.4 limit and nominal tension denominator do not apply to column equations. Their limits and moment definitions are separate.

Check and takeaway. A sum above one can pass this bolt rule while still needing individual checks. A pass must name the actual equation used.

Apply the reasoning to this section’s data and conditions

Physical interpretation: The column needs more than one pass

A slice can be strong while the whole member still buckles.

The column needs more than one pass — A slice can be strong while the whole member still buckles.

Sketch, not to scale; use the original dimensions.

  1. Check cross-section compression plus bending.
  2. Then check the separate member-buckling expressions.
  3. Keep each moment, factor and resistance in its specified expression.

Remember: The three checks do not share interchangeable denominators.

Related concept and full method

FcAgpy+|Mx|Mcx+|My|Mcy≤1Class 1/2: Mcx=min(pySx,1.2pyZx)Mcy=min(pySy,1.2pyZy)

Fc is design compression at the critical section; Mx and Mᵧ are design moments there, including the specified amplification.

Ag is gross area.

Each ratio is dimensionless, so keep force units consistent and moment units consistent.

Use magnitudes for the conservative linear interaction; moments about perpendicular axes do not cancel.

If using maxima from different locations, label the check as a conservative envelope.

This lecture expression excludes Class 4 without an appropriate local-buckling treatment.

The minor-axis 1.2pᵧZᵧ ceiling frequently controls UC sections: calculating pᵧSᵧ alone overstates the allowed moment.

The axial denominator here is A𝗀pᵧ, not the reduced member resistance Agpc.

Mechanism detailsA strong slice can belong to an unstable member2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

4. Member buckling: keep the source’s barred quantities distinct

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Apply the reasoning to this section’s data and conditions

Physical interpretation: The column needs more than one pass

A slice can be strong while the whole member still buckles.

The column needs more than one pass — A slice can be strong while the whole member still buckles.

Sketch, not to scale; use the original dimensions.

  1. Check cross-section compression plus bending.
  2. Then check the separate member-buckling expressions.
  3. Keep each moment, factor and resistance in its specified expression.

Remember: The three checks do not share interchangeable denominators.

Related concept and full method

The source uses bars to distinguish first-order moments and some resistance definitions.

Small overbars can disappear in extracted text, so read the original image.

Here “Mᵧ,first” explicitly means the source’s barred Mᵧ.

“Mx,amp” and “Mᵧ,amp” include the required amplification.

Elastic moment denominators in these member equations are pᵧZ, even for a Class 1 section.

Elastic denominator: Mex=pyZx; Mey=pyZy.
Non-sway flexural-buckling interaction (course Eq.8.80): FcPc+mx|Mx,amp|Mex+my|My,amp|Mey≤1Combined axial force/LTB (Eq.8.81): FcPcy+mLT|MLT|Mb+my|My,first|Mey≤1

For the non-sway worked method, Pc is the smaller axis resistance based on the stated/computed effective lengths; Pcy specifically uses weak-axis buckling.

Mᴸᵀ is the amplified major-axis moment governing lateral-torsional resistance, often given separately by an exam question.

Do not amplify a supplied “already amplified” Mᴸᵀ twice.

The last term of Eq.8.81 uses first-order minor-axis moment in the supplied source.

The flexural equation uses the amplified one.

This explains the apparently different 30 and 34.5kN·m values in Example 5.

Ch4 p.15: original Eqs.8.79–8.81 and definitions; inspect the overbars.

Ch 4 p.15: original Eqs.8.79–8.81 and their definitions.

Overbars are retained as printed.

These are the source symbols.

The renamed teaching symbol Mex, Mey used above is not substituted into the original equations.

Eqn 8.79: FcPc+mxM¯xMcx+myM¯yMcy≤1 Eqn 8.80: FcP¯c+mxMxMcx+myMyMcy≤1 Eqn 8.81: FcPcy+mLTMLTMb+myM¯yMcy≤1 Source definitions: Fc is the design compressive force at the critical location; Pcx, Pcy are the compression resistances about the two axes in sway mode.

Pc is the smaller of these.

P¯c is the smaller of the two non-sway compression resistances, obtained by second-order analysis or by taking effective length equal to actual member length.

Mb is the buckling moment resistance under clause 8.3.5.2.

Mx, My are the maximum major- and minor-axis design moments already amplified for P–Δ–δ effects; M¯x, M¯y are the corresponding first-order linear-analysis moments.

MLT is the amplified major-axis moment governing Mb.

In this source figure, Mcx=pyZx, Mcy=pyZy denotes elastic moment resistance.

mx, my comes from Table 8.9; mLT comes from Table 8.4.Open full-size image

For sway recognition only, Eq.8.79 uses sway-mode compression resistance with first-order end moments, while Eq.8.80 uses the alternative non-sway-mode compression resistance with amplified moments.

Eq.8.81 adds axial/LTB interaction.

The source explains that different lateral-load/initial-curvature effects can control.

Its p.17 explicitly excludes numerical sway-column design from the course.

The worked pages therefore use the non-sway branches rather than constructing an unsupported sway analysis.

Mechanism detailsA strong slice can belong to an unstable member1 concept · 6 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

5. Non-sway, sway and ultra-sensitive frames

Restraints define the analysis model

Choose an analysis model that represents the actual joints, restraints and possible sway.

Braced pathPossible sway
The joint symbol describes permitted rotation. The frame arrows describe possible sideways movement. These are separate observations.

Prediction, then explanation. A joint that permits beam rotation does not automatically remove all column moment. Eccentric reactions may still bend the column.

First identify the joint behaviour. Next identify how horizontal forces reach the foundations. Then assess sway sensitivity using the course criterion.

Simple, continuous and semi-continuous construction describe joint modelling. Sway classification describes overall frame response.

Scope. The schematic does not establish restraint stiffness or a stability threshold. Use the stated data and classification rules.

Check and takeaway. An ideal straight frame may still require notional horizontal forces to represent imperfections under the applicable method.

Compression acts on the displaced shape

A compressed member moves away from its initial load line. Explain why the bending moment can increase.

The dashed line labelled Original marks the initial position. The tilted member creates the extra horizontal lever arm shown below.
The dashed line labelled Original marks the initial position. The tilted member creates the extra horizontal lever arm shown below.

Prediction, then explanation. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Force acting through an offset forms a moment. Second-order analysis includes that changed geometry in equilibrium.

Madditional=PΔorPδM_{additional}=P\Delta\quad\text{or}\quad P\delta

P is axial force. Δ and δ are the relevant perpendicular displacements. Consistent force and length units give moment units.

Scope. Use the amplification or analysis method stated for the frame. Do not amplify an already amplified moment a second time.

Check and takeaway. Zero offset removes this additional moment in the ideal sketch. Real design may still require imperfections and code checks.

Apply the reasoning to this section’s data and conditions

Source analysis routeNon-swaySwayUltra-sensitive
Ordinary course routeλcr≥105≤λcr<10λcr<5
Advanced-analysis classification quoted by lectureλcr≥155≤λcr<15λcr<5

λcr is the elastic critical load factor: the multiple of the applied loading at which an elastic instability mode occurs.

It is not the member slenderness λ=Lᴱ/r.

Non-sway classification permits the stated global P–Δ simplification; local member P–δ amplification may still be needed.

For ultra-sensitive frames the lecture requires second-order P–Δ–δ or advanced analysis.

Bracing is the physical system restraining sway.

The classification checks how sensitive the modeled structure is.

Mechanism detailsRestraints, sway and imperfections2 concepts · 6 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A frame needs a defined path for horizontal force as well as gravity.
  2. Pinned joints alone do not provide frame moment resistance; sway restraint needs a real structural system.
  3. Diagonal bracing carries horizontal action through axial forces.

    This sketch does not assign a numerical frame classification.

  4. Use the specified imperfection/notional-force model and critical-load criteria.

    Avoid counting alternative imperfection models twice.

6. Why moments increase under compression

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Moving sideways gives the load a new lever arm

Once a compressed member moves sideways, the same compression creates extra moment.

Moving sideways gives the load a new lever arm — Once a compressed member moves sideways, the same compression creates extra moment.

Sketch, not to scale; use the original dimensions.

  1. P–Δ concerns overall frame or storey movement.
  2. P–δ concerns bowing relative to the member’s end line.
  3. Amplify only the first-order moments specified by the method.

Remember: Do not amplify a moment that the question already gives as amplified.

Related concept and full method

A compression force acting through a lateral displacement creates additional moment.

Capital Δ usually denotes frame/storey sway; small δ denotes member curvature.

Second-order analysis can include these effects directly.

If the exercise instead gives amplification factors, multiply the appropriate first-order moment once.

Lecture Eq.6.1: λcr=(FNFV)(hδN)This lecture normally takes FN=0.005FV.
Global amplification factor: 11−FVδNFNhMember amplification factor: 11−FcLE2π2EI

Fv is the factored vertical load at and above the storey.

Fᴺ is the notional horizontal load.

h is storey height. δᴺ is relative storey displacement caused by Fᴺ.

The lecture uses the larger relevant global/member factor for its general discussion.

For non-sway member design it specifies the local member factor.

Use a consistent force/length system so both denominator ratios are dimensionless.

A nonpositive denominator does not mean a negative useful amplification: the approximation has reached/breached its instability condition.

Prediction and explained answer.

Invented arithmetic: h=4,000mm, Fᴺ/Fᵥ=0.005, δᴺ=2 mm.

Find λcr and the global factor.

Answer and reasoning

λcr=0.005×4,0002=10.

The ordinary route is at the non-sway boundary.

The displayed global factor is 1010−1=1.1111.

A separate member effect may still govern.

Mechanism detailsSeparate P–Δ from P–δ1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The dashed line marks the original frame position; axial compression acts downwards.
  2. Global displacement Δ creates the additional moment PΔ.
  3. Local displacement δ is measured from the line joining the displaced ends, and adds Pδ.
  4. Follow the original analysis route.

    Do not amplify an already amplified moment or confuse critical-load factor with member slenderness.

Mechanism detailsSeparate P–Δ from P–δ1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The dashed line marks the original frame position; axial compression acts downwards.
  2. Global displacement Δ creates the additional moment PΔ.
  3. Local displacement δ is measured from the line joining the displaced ends, and adds Pδ.
  4. Follow the original analysis route.

    Do not amplify an already amplified moment or confuse critical-load factor with member slenderness.

7. Flexural moment factors are not the LTB factors

Moment shape matters within one segment

Represent a nonuniform moment distribution in the applicable member-buckling equation.

The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.
The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.

Prediction, then explanation. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Evaluate moments from the true whole-beam analysis at the required positions. Apply the exact table’s weights, signs and lower bound.

mLT is an LTB factor. mx and my belong to the specified flexural checks. They are not interchangeable.

Scope. Some rules use magnitudes; others require signed ordinates. A factor does not reduce the actual moment used in a local section check.

Check and takeaway. Measure quarter points from the segment start, not automatically from the beam’s left support.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Similar-looking moment factors come from different tables

Two recipes can use the same ingredients but different amounts.

Similar-looking moment factors come from different tables — Two recipes can use the same ingredients but different amounts.

Sketch, not to scale; use the original dimensions.

  1. Identify flexural buckling or lateral-torsional buckling first.
  2. Read the actual moment diagram, including any change of sign.
  3. Use that check’s table and its own sign and minimum-factor rules.

Remember: Table 8.9 flexural factors are not Table 8.4 LTB factors.

Related concept and full method

For an end-moment-only segment, read Table 8.9 with the signed internal end-moment ratio β.

β positive means the BMD stays on the same side; negative means it reverses.

The lecture’s column-end applied-arrow convention gives β=−MbottomMtop; confirm the actual arrow/BMD rather than applying that minus sign blindly to internal BMD ordinates.

Table 8.9, end moments only:
When 0≤β≤1: m=0.6+0.4β.
When −1≤β≤0: m=0.6+0.2β.
For example, β=−0.3→m=0.54; β=+0.7→m=0.88.
But Table 8.4a for LTB, at β=−0.3, gives mLT=0.48.

The two tables differ especially for reversing bending.

They also have different general quarter-point formulas.

For Table 8.9:

m=0.2+0.1M2+0.6M3+0.1M4Mmaxbut require m≥0.8M24Mmax

M2 and M4 are quarter-point moments.

M3 is mid-length moment.

M24 is the maximum moment magnitude in the central half.

If the three ordinates lie on one side, take them positive.

If they straddle the axis, choose the positive side that gives the larger m.

Mmax and M24 are always positive.

This sign rule differs from Table 8.4b, which uses all magnitudes.

The lecture’s special flexural cases give 0.90 for one central point,0.95 for a UDL,0.95 for three equal equally spaced points and 0.80 for the pictured two equal points; match the drawing before using them.

Table8.9, Ch4 p.18, including special cases and the general-case sign rule.

Table 8.9, Ch 4 p.18: special cases and sign rules for the general case.

X marks lateral restraint; L/LLT marks segment length.

The two end moments above are M and βM.

In the left sketch, β is positive; in the right sketch, β is negative.

The end-moment table gives β→m row by row as follows: 1.0→1.00,0.9→0.96,0.8→0.92,0.7→0.88,0.6→0.84,0.5→0.80,0.4→0.76,0.3→0.72,0.2→0.68,0.1→0.64,0.0→0.60,−0.1→0.58,−0.2→0.56,−0.3→0.54,−0.4→0.52,−0.5→0.50,−0.6→0.48,−0.7→0.46,−0.8→0.44,−0.9→0.42,−1.0→0.40.

The special cases at lower left, from top to bottom, are: one point load at midspan, m=0.90; UDL, m=0.95; three equal, equally spaced point loads, m=0.95; two equal point loads at the third points, m=0.80.

In the lower-right sketch, M1, M5 are the ends; M2, M4 are the quarter points.

M3 is the midpoint.

The source expression is:m=0.2+0.1M2+0.6M3+0.1M4Mmaxbut m≥0.8M24Mmax.

If all three sampled moments lie on the same side, take them positive.

If they lie on different sides, choose as positive the side producing the larger m.

Mmax, M24 are both positive: respectively the maximum moment over the whole segment and over its central half.Open full-size image

Column example 5: axial load plus biaxial end moments

Check a 254×254×89 UC S355 column in a braced non-sway frame,4.5m long, fixed at one end and pinned at the other. Design compression is 1,650kN. First-order factored end moments are Mx(top/bottom)=+80/+24kN·m and Mᵧ(top/bottom)=+30/−21kN·m. Amplification factors are 1.08 about x and 1.15 about y. The given amplified Mᴸᵀ=86.4 kNm has the same distribution as Mx.

Original source: LectureNotes/Ch 4_Column.pdf — p. 36, p. 37, p. 38.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

InputMeaning/value source
End moments

Given applied-arrow convention: +80/+24 about x; +30/−21 about y.

Convert to the Table 8.9 internal-diagram ratio.

AmplificationGiven 1.08 and 1.15; Mᴸᵀ86.4 already includes amplification.
Section rowData File p.11, 254×254×89 UC: T=17.3, t=10.3, d=200.3mm; bT=7.41, dt=19.4; rx=11.2cm, ry=6.55cm; A=113cm2; Zx=1,096, Zy=379, Sx=1,224, Sy=575cm3; u=0.850, x=14.5.
Restraint/curve choicesTable 8.6 recommended fixed/pinned K0.85; rolled H≤40mm uses b about x,c about y.

Why this method applies

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

This is continuous-frame end-moment design.

Therefore, use the full u–v LTB procedure and moment factors from the separate flexural/LTB tables.

Check three things: local section interaction, flexural member interaction, and axial/LTB interaction.

The section moment denominator is capped plastic resistance, whereas the member denominators are elastic pᵧZ.

The source’s LTB minor-axis term uses first-order Mᵧ.

Its flexural term uses amplified Mᵧ.

1. Strength, combined-stress classification and moments

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Apply the reasoning to this section’s data and conditions

T=17.3mm lies within 16<T≤40, so py=345Nmm2. ε=275345=0.892805Class 1 flange limit 9ε=8.03525; bT=7.41<8.03525. Web compression ratio: r1=Fcdtpy=1,650,000200.3×10.3×345≈2.318Under the supplied classification rule, r1 is limited to 1. Class 1 web limit: 80ε1+r1=80×0.8928052=35.7122dt=19.4<35.7122, so the web is Class 1 and the overall section is Class 1.Mx,amp=1.08×80=86.4kN·mMy,amp=1.15×30=34.5kN·m;My,first=30kN·mGiven MLT=86.4kN·m; do not amplify it again.

The raw r1 exceeds 1 because the axial load is divided by the web’s dt area, not total section area.

The course classification parameter is bounded.

This does not mean gross-area compression exceeds capacity.

Mechanism detailsWhy thin elements buckle locally2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The flange outstand and web have different widths, thicknesses and edge support conditions.
  2. A thinner plate can wrinkle locally before the complete member loses stability.
  3. Class 1 allows plastic rotation.

    Class 2 reaches plastic resistance.

    Class 3 reaches elastic resistance.

    Class 4 requires effective properties.

  4. Check every relevant compression element with the supplied limits and stress distribution.

    The deformation shown is qualitative.

2. Cross-section interaction

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Two simultaneous actions use one component. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

Apply the reasoning to this section’s data and conditions

Physical interpretation: The column needs more than one pass

A slice can be strong while the whole member still buckles.

The column needs more than one pass — A slice can be strong while the whole member still buckles.

Sketch, not to scale; use the original dimensions.

  1. Check cross-section compression plus bending.
  2. Then check the separate member-buckling expressions.
  3. Keep each moment, factor and resistance in its specified expression.

Remember: The three checks do not share interchangeable denominators.

Related concept and full method

Agpy=113×100×3451,000=3,898.5kNMajor axis: pySx=345×1,2241,000=422.28kN·mUpper cap: 1.2pyZx=1.2×345×1,0961,000=453.744kN·mMcx=422.28kN·mMinor axis: pySy=345×5751,000=198.375kN·mUpper cap: 1.2pyZy=1.2×345×3791,000=156.906kN·mMcy=156.906kN·mUtilisation: 1,6503,898.5+86.4422.28+34.5156.906=0.847720<1Section passes.

Both maximum moment magnitudes occur at the top in the given load schedule, so they coexist with the stated compression there.

The minor-axis ceiling is the governing branch for Mcy.

Mechanism detailsA strong slice can belong to an unstable member2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

3. Effective length and both axial buckling resistances

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Use the same mechanism: Move between two known values. If the second strength is lower, moving toward that row must reduce the interpolated strength.

Apply the reasoning to this section’s data and conditions

LEx=LEy=0.85×4,500=3,825mmrx=112mm;ry=65.5mmλx=3,825112=34.151786λy=3,82565.5=58.396947

Select curve b for x and c for y.

Both use pᵧ345.

The source shows only the controlling y result.

The x lookup below completes the omitted comparison.

Curve b, x axis: 30 row gives 325,35 row gives 318Nmm2. Interpolation fraction: 34.151786−3035−30=0.830357pc=325+0.830357×(318−325)=319.187500Nmm2Curve c, y axis: 58 row gives 247,60 row gives 241Nmm2. Interpolation fraction: 58.396947−5860−58=0.198473pc=247+0.198473×(241−247)=245.809160Nmm2Pcx=113×319.18750010=3606.818750kNPcy=113×245.80916010=2777.643511kNPc=Pcy=2777.643511kN

Mechanism detailsEffective length and buckling axes3 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

4. Read the two flexural factors and the LTB factor

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Similar-looking moment factors come from different tables

Two recipes can use the same ingredients but different amounts.

Similar-looking moment factors come from different tables — Two recipes can use the same ingredients but different amounts.

Sketch, not to scale; use the original dimensions.

  1. Identify flexural buckling or lateral-torsional buckling first.
  2. Read the actual moment diagram, including any change of sign.
  3. Use that check’s table and its own sign and minimum-factor rules.

Remember: Table 8.9 flexural factors are not Table 8.4 LTB factors.

Related concept and full method

The question defines signs for applied clockwise/anticlockwise end moments.

The internal end-moment diagram reverses the bottom-end sign relative to that schedule.

Thus the same positive applied signs about x create a reversing BMD, while the opposite applied signs about y create a same-side BMD.

βx=−2480=−0.3Table 8.9: mx=0.54. βy=−(−21)30=+0.7Table 8.9: my=0.88. MLT and x axis has the same moment-diagram shape; β=−0.3. Table 8.4a: mLT=0.48.

Do not read 0.48 as mx: that belongs to the different LTB table.

Uniform amplification about an axis multiplies both ends equally and leaves the end-moment ratio unchanged.

Mechanism detailsRead the moment shape within one segment3 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Moment ordinates must belong to the same effective unbraced segment.
  2. Same-side and reverse-curvature diagrams have different signed end ratios.
  3. The markers show ¼, ½ and ¾ of this segment, not of the entire beam.
  4. LTB and column flexural factors are different.

    Preserve their individual bounds and coefficient sets.

5. Flexural member interaction with elastic denominators

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Two simultaneous actions use one component. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

Apply the reasoning to this section’s data and conditions

Mex=pyZx=345×1,0961,000=378.12kN·mMey=pyZy=345×3791,000=130.755kN·mUflex=1,6502777.643511+0.54×86.4378.12+0.88×34.5130.755=0.594029+0.123389+0.232190=0.949608<1Passes.

Mechanism detailsA strong slice can belong to an unstable member2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

6. Axial/LTB interaction

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: Two simultaneous actions use one component. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A beam can escape sideways

The compressed flange can move sideways while the section twists.

A beam can escape sideways — The compressed flange can move sideways while the section twists.

Sketch, not to scale; use the original dimensions.

  1. Divide the beam at effective lateral restraints.
  2. Use each segment’s effective length to obtain its buckling resistance.
  3. Compare that resistance with the segment’s equivalent moment demand.

Remember: A section bending check alone does not check lateral-torsional buckling.

Related concept and full method

λ=58.396947; section torsional index x=14.5. v=[1+0.05(58.39694714.5)2]−0.25=0.862028βw=1;λLT=0.850×0.862028×58.396947=42.788808Table 8.3a,py=345 column: 40 row gives 317,45 row gives 302Nmm2. Interpolation fraction: 42.788808−4045−40=0.557762pb=317+0.557762×(302−317)=308.633576Nmm2Mb=308.633576×1,2241,000=377.767497kN·mULT=1,6502777.643511+0.48×86.4377.767497+0.88×30130.755=0.594029+0.109782+0.201904=0.905715<1Passes.

The 30kN·m in the last term is intentional: source Eq.8.81 has barred, first-order Mᵧ.

The 86.4kN·m Mᴸᵀ is already amplified.

All three interactions pass; flexural member interaction is closest to 1.

Mechanism detailsA strong slice can belong to an unstable member5 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

Result and concise exam wording

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

S355 254×254×89 UC: py=345, Class 1.

Section utilisation 0.84772.

LE=3,825mm; λx=34.1518, λy=58.3969; curves b/c give pcx=319.1875, pcy=245.8092Nmm2.

Pc=Pcy=2,777.6435kN.

mx=0.54, my=0.88; elastic resistance 378.12/130.755kN·m; flexural-buckling utilisation 0.94961.

v=0.862028, λLT=42.7888, pb=308.6336, Mb=377.7675kN·m, mLT=0.48; axial force/LTB utilisation 0.90571.

All pass.

Misconceptions and checks

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Two simultaneous actions use one component. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

Apply the reasoning to this section’s data and conditions

  • Use 345, not 355, for the 17.3mm flange.
  • Apply the 1.2pᵧZ ceiling on the minor axis.
  • Do not use capped plastic capacities in the member interaction.
  • Distinguish applied end signs from internal moment-diagram signs.
  • Keep first-order Mᵧ in the source Eq.8.81 term.

How the method transfers to a new variant

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: A force couple carries moment. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Apply the reasoning to this section’s data and conditions

  1. Identify axial load, any moments, actual length and restraints in each axis.
  2. Choose/read a section and confirm strength from the actual thickness.
  3. Check the appropriate flange and web local-slenderness limits.
  4. Find λx and λy separately.

    Select each axis curve and interpolate pc.

  5. Calculate both axial resistances and identify the governing axis.
  6. If moments exist, complete section, flexural and axial/LTB interactions using their own capacities and moment definitions.

Prediction with explained answer

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: Keep load categories separate. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Invented variant: only the imposed major-axis end moments in the given factored schedule are replaced by+88/+26.4kN·m; treat these as a 10% increase of the stated total first-order x moments, with axial load and y moments unchanged.

How do the checks change?

Answer and reasoning

x-axis end-moment ratio remains −0.3, so mx=0.54, mLT=0.48 are unchanged.Mx,amp=MLT=1.08×88=95.04kN·m.

Section utilisation increases by 8.64422.28≈0.02046 to 0.86818.

Flexural-buckling utilisation increases by 0.54×8.64378.12≈0.01234 to 0.96195.

LTB utilisation increases by 0.48×8.64377.7675≈0.01098 to 0.91669.

All still pass, with resistance properties unchanged.

Mechanism detailsA strong slice can belong to an unstable member3 concepts · 3 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

Mechanism detailsRead the moment shape within one segment1 concept · 31 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Moment ordinates must belong to the same effective unbraced segment.
  2. Same-side and reverse-curvature diagrams have different signed end ratios.
  3. The markers show ¼, ½ and ¾ of this segment, not of the entire beam.
  4. LTB and column flexural factors are different.

    Preserve their individual bounds and coefficient sets.

8. Simple construction: eccentric reactions still bend columns

An eccentric beam reaction bends the column

A simple beam joint delivers a vertical reaction away from the column centre. Find the resulting column moments.

The reaction arrow is offset by e from the column centre. The upper and lower arrows show where the joint moment is shared.
The reaction arrow is offset by e from the column centre. The upper and lower arrows show where the joint moment is shared.

Prediction, then explanation. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Sum axial forces first. Calculate the signed eccentric moments. Share the net joint moment between upper and lower columns using the stated stiffness model.

M=Re,Mlower=MKlowerKupper+KlowerM=Re,\qquad M_{lower}=M\frac{K_{lower}}{K_{upper}+K_{lower}}

R is reaction; e is perpendicular eccentricity. K denotes the stiffness measure prescribed for moment sharing.

Scope. Equal sharing requires equal stated stiffness. Use actual storey length where the special simple-construction LTB rule requires it.

Check and takeaway. A pin-like beam connection can still cause an eccentric reaction moment in the column. Joint rotation and reaction location are separate facts.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A pinned beam can still bend its column

Its reaction can miss the column centre and create a lever arm.

A pinned beam can still bend its column — Its reaction can miss the column centre and create a lever arm.

Sketch, not to scale; use the original dimensions.

  1. Find the reaction’s actual nominal eccentricity.
  2. Multiply reaction by eccentricity to obtain the joint moment.
  3. Share that moment using the stated column-stiffness model.

Remember: Equal sharing needs equal relevant stiffness.

It is not automatic.

Related concept and full method

A simple beam-to-column joint does not transmit a rigid-frame end moment.

Its vertical reaction may still act away from the column centre.

The nominal eccentricity is measured from the column centroid to the reaction line.

For a beam resting on a column face, compare two possible reaction positions.

The first is 100mm from that face.

The second is the centre of stiff bearing.

Use the position farther from the face.

Add the centroid-to-face distance (for the illustrated major-axis case, D2).

M=ReWith columns both above and below the joint, distribute net moment in proportion to IL: Mlower=MIlowerLlower(IlowerLlower)+(IupperLupper)

For identical sections above and below, I cancels.

A3 m lower column is twice as stiff by IL as a 6m upper one, so shares are 23 and 13.

Opposite equal reactions cancel their nominal moments about that axis but still add to axial compression.

The upper column carries roof loads.

The lower carries roof plus intermediate-floor loads.

Do not distribute accumulated axial load using the moment-stiffness fractions.

Special simple-construction rule: mx=my=mLT=1When looking up bending strength: λLT=0.5Lrywhere L is actual storey length. For axial buckling, use the applicable end-restraint conditions: λ=LEr

The source allows all beams fully loaded without pattern loading for this simplified column procedure.

It also says a beam loaded above 90% of its capacity should not be assumed to afford column rotational restraint.

These are applicability conditions, not universal properties of every beam connection.

The special 0.5L/rᵧ rule uses actual L, not the reduced effective column length.

Column example 3: loads and eccentric moments in two storeys

Check 203×203×60 UC S355 in a two-storey simple-construction column. The lower storey is 3m, the upper 6m. Use the supplied reaction table and stated construction assumptions, including a pinned base and 1.15 moment amplification.

Original source: LectureNotes/Ch 4_Column.pdf — p. 25, p. 26, p. 27, p. 28, p. 29, p. 30, p. 31.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

Use the same mechanism: An eccentric beam reaction bends the column. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

Given modelImplication
Continuous column, simple beam constructionUse nominal eccentricity and IL moment sharing; all moment factors are 1.
Base effectively pinned

Lower segment has no base rotational fixity.

Substantial level 2 members give the source’s upper restraint assumption.

Roof secondary beams are small tiesProvide positional but not rotational restraint for the upper column’s weak-axis buckling.
Main beams connect by web and seating cleatsSource adopts reaction line 100mm beyond the column face.
Self-weightSource assumes 20kN characteristic dead self-weight at each level; include it once per level.
Section dataData p.11: D=209.6, t=9.4, T=14.2, d=160.8mm, bT=7.25, dt=17.1, rx=8.96cm, ry=5.20cm, A=76.4cm2, Sx=656, Sy=305, Zx=584, Zy=201cm3.

Why this method applies

Use the same mechanism: An eccentric beam reaction bends the column. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Use the same mechanism: A force couple carries moment. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Balance the isolated beam

Find the two vertical reactions before calculating internal shear or moment.

A / RₐB / RᵦPaL
A and B are vertical supports. The downward load acts at distance a from A. Its distance from B is L − a.

Prediction, then explanation. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Take moments about A. Reaction A has zero lever arm there. Then use vertical force balance to find reaction A.

RBL=Pa,RA+RB=PR_B L=Pa,\qquad R_A+R_B=P

P, RA and RB are forces in kN. L is support spacing and a is load position, both in m.

Scope. These expressions describe one point load on a simply supported beam. Add other loads through equilibrium; keep their actual positions.

Check and takeaway. Illustration: P = 60 kN, L = 6 m and a = 2 m give RB = 20 kN and RA = 40 kN.

Apply the reasoning to this section’s data and conditions

There are two separate accounting tasks.

Axial load accumulates down the column.

Eccentric reactions create a net joint moment which is shared between the upper and lower column in proportion to IL.

Equal opposite secondary reactions cancel their moments, but their vertical loads still add.

Keep these operations separate.

This solution retains arithmetic precision.

A short comparison also explains the source’s rounded values.

1. Recalculate every reaction-table entry and storey total

Use the same mechanism: Keep load categories separate. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

Follow one strip of floor

An area load must become a beam load before beam reactions can be calculated.

The highlighted tributary strip supplies one beam. The right-hand labels show area load multiplied by width becoming line load.
The highlighted tributary strip supplies one beam. The right-hand labels show area load multiplied by width becoming line load.

Prediction, then explanation. At fixed area load, twice the tributary width gives twice the line load. An end reaction remains a concentrated force.

Consider one metre along the beam. The associated floor area is b square metres. Multiply area load by that width.

w=qbw=qb

q is area load in kN/m²; b is tributary width in m; w is line load in kN/m.

Scope. Determine b from slab spanning and supports. Add beam self-weight separately. A secondary-beam reaction is not automatically a UDL.

Check and takeaway. Illustration: 3 kN/m2×2 m=6 kN/m3\,\mathrm{kN/m^2}\times2\,\mathrm{m}=6\,\mathrm{kN/m}. The width cancels one length unit.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

Level/reactionGiven G (kN)1.4GGiven Q (kN)1.6QUltimate total
3: R132028203260
3: R332028203260
3: R232433.680128161.6
3: assumed self-weight20280028
3 totals84117.6120192309.6
2: R123042100160202
2: R323042100160202
2: R223042200320362
2: assumed self-weight20280028
2 added totals110154400640794
Upper column segment 2–3: Fc=309.6kN. Lower column segment 1–2: Fc=309.6+794=1,103.6kN. Check using accumulated components: G=84+110=194kN;Q=120+400=520kN1.4×194+1.6×520=271.6+832=1,103.6kN

Mechanism detailsFrom characteristic to design load3 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. G is permanent load; Q is imposed load.

    A surface load and a line load also have different units.

  2. This illustration uses the course gravity case .

    Other combinations in the original text retain their own factors.

  3. For illustrative , the separate load contributions show what changes when Q increases.
  4. Do not carry this ULS total automatically into deflection.

    Follow the stated SLS load case.

2. Strength and section classification

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Apply the reasoning to this section’s data and conditions

T=14.2≤16mm→py=355Nmm2ε=275355=0.880141Flange: bT=7.25<9ε=7.92127, Class 1. Lower-storey web: r1=1,103,600160.8×9.4×355≈2.057Use the cap r1=1. Class 1 web limit: 80ε1+r1=40ε=35.2056dt=17.1<35.2056; the web is Class 1. The upper storey has smaller axial force and also passes using this same conservative web limit.

The lower section’s larger axial compression is sufficient for checking this section’s worst compression/bending web limit.

The selected section has the same geometry throughout both storeys.

Mechanism detailsWhy thin elements buckle locally1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The flange outstand and web have different widths, thicknesses and edge support conditions.
  2. A thinner plate can wrinkle locally before the complete member loses stability.
  3. Class 1 allows plastic rotation.

    Class 2 reaches plastic resistance.

    Class 3 reaches elastic resistance.

    Class 4 requires effective properties.

  4. Check every relevant compression element with the supplied limits and stress distribution.

    The deformation shown is qualitative.

3. Calculate section and elastic member capacities

Internal tension and compression resist moment

Find which section resistance applies before comparing it with the moment demand.

In sagging bending, the upper region compresses and the lower region stretches. Together their forces form a resisting couple.
In sagging bending, the upper region compresses and the lower region stretches. Together their forces form a resisting couple.

Prediction, then explanation. A larger appropriate section modulus raises resistance at fixed strength. Local plate buckling can restrict the usable modulus.

Classify the section first. At low shear, use the elastic expression for Class 3 or the prescribed capped plastic expression for Classes 1 and 2.

Mc=min⁡(pyS,1.2pyZ)for Class 1/2 at low shearM_c=\min(p_yS,1.2p_yZ)\quad\text{for Class 1/2 at low shear}

py uses N/mm². S is plastic modulus and Z is elastic modulus, both in mm³. Mc then uses N·mm.

Scope. This is section resistance, not whole-member LTB resistance. High shear and Class 4 require their appropriate treatment.

Check and takeaway. Selecting the larger of the two capped terms defeats the cap. Use their minimum.

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Apply the reasoning to this section’s data and conditions

Ag=76.4×100=7,640mm2Agpy=7,640×3551,000=2,712.2kNMcx=min(355×6561,000,1.2×355×5841,000)=min(232.88,248.784)=232.88kN·mMcy=min(355×3051,000,1.2×355×2011,000)=min(108.275,85.626)=85.626kN·mElastic denominator for member checks: Mex=355×5841,000=207.32kN·mMey=355×2011,000=71.355kN·m

The linear section interaction uses 232.88 and 85.626.

The member interaction uses 207.32 and 71.355.

The source reuses similar Mc notation for different definitions.

Keep a clearly labelled capacity list.

Mechanism detailsCompression and tension across a section2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For sagging, the top flange is in compression and the bottom in tension; hogging reverses this.
  2. Elastic bending stress varies with distance from the neutral axis: .
  3. The section class governs whether elastic, plastic or effective properties may be used.
  4. Use the shear at the section under examination.

    The largest shear elsewhere is not automatically coexistent.

4. Nominal eccentricity and stiffness sharing at level 2

Use the same mechanism: An eccentric beam reaction bends the column. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A pinned beam can still bend its column

Its reaction can miss the column centre and create a lever arm.

A pinned beam can still bend its column — Its reaction can miss the column centre and create a lever arm.

Sketch, not to scale; use the original dimensions.

  1. Find the reaction’s actual nominal eccentricity.
  2. Multiply reaction by eccentricity to obtain the joint moment.
  3. Share that moment using the stated column-stiffness model.

Remember: Equal sharing needs equal relevant stiffness.

It is not automatic.

Related concept and full method

The main beam reaction R22 acts on one flange.

D2 takes us from the centroid to the flange face.

The nominal 100mm then takes us to the source’s reaction line.

R12 and R32 have equal magnitudes on opposite sides, so their minor-axis nominal moments cancel.

ex=D2+100=209.62+100=204.8mm=0.2048mM2=R22×ex=362×0.2048=74.1376kN·mLower-storey stiffness proportion: I3I3+I6=23Upper-storey stiffness proportion: I6I3+I6=13M2→1,first=74.1376×23=49.4250667kN·mM2→3,first=74.1376×13=24.7125333kN·mCheck the sum: 49.4250667+24.7125333=74.1376kN·mSymmetric opposing secondary-beam reactions give My=0.

The lower storey is shorter, hence stiffer and receives the larger moment share.

The source rounds e to 205mm, M2 to 74.2 and shares to 49.5/24.7.

The little moment diagrams on p.28 show the moment components associated with this joint sharing; they are not additional applied point loads.

Mechanism detailsEccentric reactions and stiffness sharing1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A beam reaction can act away from the column centre even at a nominally pinned beam connection.
  2. .

    Opposing reactions can cancel part of the signed moment, while both still add compression.

  3. The course simple model distributes the joint moment in proportion to of the columns above and below.
  4. Equal relevant stiffness gives half each.

    A roof joint with no upper column is a different case.

5. Lower-storey section interaction

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Two simultaneous actions use one component. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Apply the reasoning to this section’s data and conditions

Physical interpretation: The column needs more than one pass

A slice can be strong while the whole member still buckles.

The column needs more than one pass — A slice can be strong while the whole member still buckles.

Sketch, not to scale; use the original dimensions.

  1. Check cross-section compression plus bending.
  2. Then check the separate member-buckling expressions.
  3. Keep each moment, factor and resistance in its specified expression.

Remember: The three checks do not share interchangeable denominators.

Related concept and full method

Mx,amp=1.15×49.4250667=56.838827kN·mMLT=Mx,amp;My=0Usection=1,103.62,712.2+56.838827232.88+0=0.650971<1Lower-storey section passes.

Using the rounded source loads and moments gives 1,1042,712.2+1.15×49.5232.88≈0.6515.

Both precision levels agree with the source result of approximately 0.65.

Mechanism detailsA strong slice can belong to an unstable member3 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

6. Lower-storey member buckling

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why a long column can fail before crushing

Push a long thin ruler from both ends: it may bow sideways first.

Why a long column can fail before crushing — Push a long thin ruler from both ends: it may bow sideways first.

Sketch, not to scale; use the original dimensions.

  1. Find effective length and radius of gyration for each axis.
  2. Calculate slenderness for both directions.
  3. Use the appropriate buckling curve before forming resistance.

Remember: Compare the final resistances; slenderness alone may not identify the controlling axis.

Related concept and full method

The source assumes rotational and positional restraint at level 2 in both axes.

The base is pinned.

Table 8.6 recommended fixed/pinned factor is 0.85.

Use that assumed model explicitly, rather than inferring a rigid base from the drawing’s plate line.

LEx=LEy=0.85×3,000=2,550mmλx=2,55089.6=28.459821λy=2,55052=49.038462Hot-rolled H-section, thickness ≤40mm, py=355: x axis uses curve b; y axis uses curve c. Curve b: 25 row gives 342,30 row gives 335Nmm2. Interpolation fraction: 28.459821−2530−25=0.691964pc=342+0.691964×(335−342)=337.156250Nmm2Curve c: 48 row gives 280,50 row gives 275Nmm2. Interpolation fraction: 49.038462−4850−48=0.519231pc=280+0.519231×(275−280)=277.403846Nmm2Pcx=7,640×337.1562501,000=2575.873750kNPcy=7,640×277.4038461,000=2119.365385kNPc=Pcy=2119.365385kN

Simple construction sets all m factors to 1.

For bending buckling use actual storey length 3,000mm, not 2,550mm:

λLT=0.5Lry=0.5×3,00052=28.846154Table 8.3a,py=355: 25 and 30 rows all give 355, giving pb=355. Mb=355×6561,000=232.88kN·mFlexural-buckling interaction: 1,103.62119.365385+1×56.838827207.32+0=0.794882<1Axial force/LTB interaction: 1,103.62119.365385+1×56.838827232.88+0=0.764791<1

Mechanism detailsA strong slice can belong to an unstable member5 concepts · 4 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

7. Upper-storey governing moment and section interaction

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Two simultaneous actions use one component. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Apply the reasoning to this section’s data and conditions

Roof reaction: R23=1.4×24+1.6×80=161.6kNRoof nominal moment: M3=161.6×0.2048=33.09568kN·mMoment allocated to the bottom of the upper column segment: 24.712533kN·m. Governing first-order moment magnitude: max(33.09568,24.712533)=33.09568kN·mMx,amp=MLT=1.15×33.09568=38.060032kN·mFc=309.6kN;My=0Usection=309.62,712.2+38.060032232.88=0.277583<1Upper-storey section passes.

The upper-storey moment is governed by the roof reaction, not automatically the moment inherited at level 2.

The source uses 162×0.205≈33.2, giving amplified 38.18≈38.2.

Its printed 0.27 comes from early rounding of the separate utilisation terms; full arithmetic is about 0.28 at two decimal places.

Mechanism detailsA strong slice can belong to an unstable member3 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

8. Upper-storey buckling about both axes

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

The main roof beam supplies the source’s major-axis rotational restraint.

The small secondary roof ties only restrain position in the weak direction.

With level 2 restrained, the lecture uses 0.70L for x and 0.85L for y.

LEx=0.70×6,000=4,200mm;LEy=0.85×6,000=5,100mmλx=4,20089.6=46.875λy=5,10052=98.076923Curve b, 355 column: 46 row gives 306,48 row gives 302Nmm2. Interpolation fraction: 46.875000−4648−46=0.437500pc=306+0.437500×(302−306)=304.250000Nmm2Curve c, 355 column: 98 row gives 145,100 row gives 140Nmm2. Interpolation fraction: 98.076923−98100−98=0.038462pc=145+0.038462×(140−145)=144.807692Nmm2Pcx=7.64×304.250000=2324.470000kNPcy=7.64×144.807692=1106.330769kNMinor axis governs. Simple construction: λLT=0.5×6,00052=57.692308Table 8.3a,355 column: 55 row gives 274,60 row gives 257Nmm2. Interpolation fraction: 57.692308−5560−55=0.538462pb=274+0.538462×(257−274)=264.846154Nmm2Mb=264.846154×6561,000=173.739077kN·mFlexural-buckling interaction: 309.61106.330769+38.060032207.32=0.463425<1Axial force/LTB interaction: 309.61106.330769+38.060032173.739077=0.498908<1

Both storeys pass all three demonstrated interaction checks.

The lower-storey flexural interaction, approximately 0.795, is the largest.

The original source-rounded results are approximately lower 0.65/0.79/0.76 and upper 0.28/0.46/0.50.

Mechanism detailsA strong slice can belong to an unstable member6 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

Result and concise exam wording

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Use the same mechanism: An eccentric beam reaction bends the column. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Use the same mechanism: Two simultaneous actions use one component. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

Apply the reasoning to this section’s data and conditions

Using exact arithmetic: upper/lower compression 309.6/1,103.6kN. pᵧ355,Class 1; A𝗀pᵧ2,712.2 kN; section capacities 232.88/85.626kN·m; elastic 207.32/71.355.

e=204.8mm; level 2 moment 74.1376kN·m shares 49.4251/24.7125.

Amplified lower moment 56.8388; upper governing 38.0600.

Lower Pc=2,119.365kN,Mᵦ232.88; interactions 0.6510/0.7949/0.7648.

Upper Pc=1,106.331kN,Mᵦ173.7391; interactions 0.2776/0.4634/0.4989.

Both storeys adequate under the stated simple-construction restraint assumptions.

Misconceptions and checks

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Apply the reasoning to this section’s data and conditions

  • Accumulate both levels for lower axial load.
  • Cancel opposite moments, not the underlying compressive reactions.
  • Share moment by IL, not equally and not by axial-force ratios.
  • Use actual storey length in 0.5L/rᵧ.
  • Do not treat a small roof tie as rotational restraint.

How the method transfers to a new variant

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Use the same mechanism: An eccentric beam reaction bends the column. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Apply the reasoning to this section’s data and conditions

  1. Trace the loads above each column segment and keep dead/imposed components separate.
  2. Read actual storey heights, section properties and end restraints in both axes.
  3. For simple construction derive nominal eccentric moments and share them by IL.
  4. Classify the section and form the correct section and member resistances.
  5. Apply only the prescribed load reductions and moment amplification rules.
  6. Check every storey segment and report both the governing check and source assumptions.

Prediction with explained answer

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Use the same mechanism: An eccentric beam reaction bends the column. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Invented variant: change only the upper-storey length from 6m to 3m, retaining the same column section and level 2 moment 74.1376kN·m.

How is that joint moment shared?

Answer and reasoning

The upper and lower IL values now match.

Therefore, each receives 74.13762=37.0688kN·m.

The lower amplified share becomes 42.62912kN·m.

This redistribution does not alter the accumulated axial loads.

Upper buckling lengths and 0.5L/rᵧ also change and must be recalculated.

The original upper resistance cannot be reused.

Mechanism detailsEccentric reactions and stiffness sharing2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A beam reaction can act away from the column centre even at a nominally pinned beam connection.
  2. .

    Opposing reactions can cancel part of the signed moment, while both still add compression.

  3. The course simple model distributes the joint moment in proportion to of the columns above and below.
  4. Equal relevant stiffness gives half each.

    A roof joint with no upper column is a different case.

Column example 4: tributary area and cumulative column loads

Design internal column A in S355 for axial load only. Roof dead/imposed intensities are 5/1.5kNm2; floor intensities 7/3kNm2. Upper storey height 4m; lower 4.5m. The foundation is fixed. Floor beams prevent translation but do not restrain column rotation. All given dead loads include beam and column self-weight.

Original source: LectureNotes/Ch 4_Column.pdf — p. 32, p. 33, p. 34, p. 35.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

Use the same mechanism: Follow one strip of floor. At fixed area load, twice the tributary width gives twice the line load. An end reaction remains a concentrated force.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

InputWhere to read it
Tributary dimensions

Plan labels 3.8+3.8=7.6m and 3+3=6m.

Use plan area, not storey height.

Vertical dimensionsElevation 4m upper and 4.5m lower.
Roof/floor loads

Question text.

The same floor plan applies at both levels.

Axial-only scope

Explicitly requested.

No eccentric moment is introduced into this exercise.

Imposed reductionLecture p.33 applies its 2011 load-code floor-count table; roof counts as a floor.

Why this method applies

Use the same mechanism: Follow one strip of floor. At fixed area load, twice the tributary width gives twice the line load. An end reaction remains a concentrated force.

Apply the reasoning to this section’s data and conditions

Multiply each level’s pressure by the area feeding the column.

The upper segment carries only roof loading.

The lower carries roof plus first floor.

Reduce the cumulative imposed load only when the source’s permitted floor-count rule applies.

After factoring, design each storey separately because loads, lengths and end conditions differ.

1. Derive the tributary area from the hatched plan

Use the same mechanism: Follow one strip of floor. At fixed area load, twice the tributary width gives twice the line load. An end reaction remains a concentrated force.

Apply the reasoning to this section’s data and conditions

Physical interpretation: How a floor load reaches a beam

Each beam collects the load from its own strip of floor.

How a floor load reaches a beam — Each beam collects the load from its own strip of floor.

Sketch, not to scale; use the original dimensions.

  1. Find the tributary width from the actual plan.
  2. Area load × tributary width gives load per beam length.
  3. A supporting beam receives the other beam’s end reaction.

Remember: A reaction becomes a point load, not automatically a UDL.

Related concept and full method

Tributary width: 7.62+7.62=3.8+3.8=7.6mTributary depth: 62+62=3+3=6mAtrib=7.6×6=45.6m2

Half of each adjacent simply supported bay reaches column A.

The hatch is a load-allocation area, not the column’s steel cross-sectional area.

Both roof and floor use 45.6m2.

Mechanism detailsFollow the floor load in 3D1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The floor carries pressure in .

    The highlighted strip belongs to one secondary beam.

  2. Multiply pressure by tributary width: .

    The illustration uses .

  3. A primary beam receives the secondary beam reaction at their connection, not a new full-span UDL.
  4. Trace reactions down to columns and foundations.

    Count each loaded area once.

2. Read the source’s floor-count reduction

Use the same mechanism: Follow one strip of floor. At fixed area load, twice the tributary width gives twice the line load. An end reaction remains a concentrated force.

Use the same mechanism: Keep load categories separate. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

Floors carried12345678Over 8
Imposed reduction0%5%10%15%20%25%30%35%40% maximum

The upper member supports one roof level →0% reduction.

The lower supports roof plus first floor →two levels →5%.

Retain 95% of the cumulative imposed load below the floor.

This is the rule applied by this lecture example, attributed there to the 2011 Dead and Imposed Loads Code.

Do not extend it automatically to an occupancy or question where reduction is disallowed.

Dead load is not reduced.

Mechanism detailsFollow the floor load in 3D3 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The floor carries pressure in .

    The highlighted strip belongs to one secondary beam.

  2. Multiply pressure by tributary width: .

    The illustration uses .

  3. A primary beam receives the secondary beam reaction at their connection, not a new full-span UDL.
  4. Trace reactions down to columns and foundations.

    Count each loaded area once.

3. Compute characteristic and ultimate loads at each level

Use the same mechanism: Keep load categories separate. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

Apply the reasoning to this section’s data and conditions

Roof: G=5×45.6=228kN;Q=1.5×45.6=68.4kNAdditional first-floor load: G=7×45.6=319.2kN;Q=3×45.6=136.8kNLower-storey accumulated load: G=228+319.2=547.2kNQ=68.4+136.8=205.2kNUpper-storey design force: F=1.4×228+1.6×68.4=319.2+109.44=428.64kNReduced lower-storey imposed load: Q=0.95×205.2=194.94kNLower-storey design force: F=1.4×547.2+1.6×194.94=766.08+311.904=1,077.984kN

All self-weight is already included.

The lower load uses the whole accumulated load rather than adding an already factored/reduced upper force to a separately reduced floor force.

Mechanism detailsFrom characteristic to design load1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. G is permanent load; Q is imposed load.

    A surface load and a line load also have different units.

  2. This illustration uses the course gravity case .

    Other combinations in the original text retain their own factors.

  3. For illustrative , the separate load contributions show what changes when Q increases.
  4. Do not carry this ULS total automatically into deflection.

    Follow the stated SLS load case.

4. Select and check the upper column

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A pinned beam can still bend its column

Its reaction can miss the column centre and create a lever arm.

A pinned beam can still bend its column — Its reaction can miss the column centre and create a lever arm.

Sketch, not to scale; use the original dimensions.

  1. Find the reaction’s actual nominal eccentricity.
  2. Multiply reaction by eccentricity to obtain the joint moment.
  3. Share that moment using the stated column-stiffness model.

Remember: Equal sharing needs equal relevant stiffness.

It is not automatic.

Related concept and full method

Trial 152×152×30 UC.

Data File p.11 gives T=9.4mm, bT=8.13, dt=19.0, A=38.3cm2, rx=6.76cm, ry=3.83cm.

The original lecture uses the same area 38.3.

T≤16, giving py=355.

Both ends are held in position but free to rotate, so K=1, with both axes having LE=4,000mm.

ε=275355=0.880141bT=8.13<13ε=11.4418;dt=19.0<40ε=35.2056Non-slender.λx=4,00067.6=59.171598λy=4,00038.3=104.438642Hot-rolled H-section thickness ≤40mm,x axis curve b; y axis curve c; py=355. Curve b: 58 row gives 278,60 row gives 272Nmm2. Interpolation fraction: 59.171598−5860−58=0.585799pc=278+0.585799×(272−278)=274.485207Nmm2Curve c: 104 row gives 133,106 row gives 129Nmm2. Interpolation fraction: 104.438642−104106−104=0.219321pc=133+0.219321×(129−133)=132.122715Nmm2Pcx=3,830×274.4852071,000=1051.278343kNPcy=3,830×132.1227151,000=506.030000kNPc=506.030000kN>428.64kNAdequate. Utilisation: 428.64506.030000=0.847064

The source uses rounded pc=132, so 38.3×13210=505.56kN and prints 505.6.

Exact interpolation gives 506.030kN.

Both pass.

The previously omitted major-axis comparison is provided above.

Mechanism detailsEffective length and buckling axes5 concepts · 13 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

5. Select and check the lower column

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

Physical interpretation: The column needs more than one pass

A slice can be strong while the whole member still buckles.

The column needs more than one pass — A slice can be strong while the whole member still buckles.

Sketch, not to scale; use the original dimensions.

  1. Check cross-section compression plus bending.
  2. Then check the separate member-buckling expressions.
  3. Keep each moment, factor and resistance in its specified expression.

Remember: The three checks do not share interchangeable denominators.

Related concept and full method

Trial 203×203×46 UC.

Data File p.11 gives T=11.0mm, bT=9.25, dt=22.3, A=58.7cm2, rx=8.82cm, ry=5.13cm.

The flange thickness again gives py=355.

The base is fixed.

The floor end is held in position but free to rotate.

Therefore, use the recommended factor K=0.85.

LEx=LEy=0.85×4,500=3,825mmbT=9.25<13ε=11.4418;dt=22.3<40ε=35.2056Non-slender.λx=3,82588.2=43.367347λy=3,82551.3=74.561404Curve b, py=355: 42 row gives 314,44 row gives 310Nmm2. Interpolation fraction: 43.367347−4244−42=0.683673pc=314+0.683673×(310−314)=311.265306Nmm2Curve c, py=355: 74 row gives 205,76 row gives 200Nmm2. Interpolation fraction: 74.561404−7476−74=0.280702pc=205+0.280702×(200−205)=203.596491Nmm2Pcx=5,870×311.2653061,000=1827.127347kNPcy=5,870×203.5964911,000=1195.111404kNPc=1195.111404kN>1,077.984kNAdequate. Utilisation: 1,077.9841195.111404=0.901995

The source rounds pc to 204, giving 58.7×20410=1,197.48kN (printed 1,197).

Exact interpolation gives 1,195.111kN.

Both selected columns pass the requested axial-only design.

The lower weak-axis check is more highly utilised.

Mechanism detailsEffective length and buckling axes5 concepts · 10 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

Result and concise exam wording

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

Atrib=45.6m2.

Roof G/Q is 228/68.4kN; lower-storey accumulation 547.2/205.2kN.

Upper-storey ultimate force 428.64kN; lower-storey imposed load after reduction 5% gives 1,077.984kN.

Upper-storey 152×152×30 UC: non-slender, LE=4m, Pc=506.030kN.

Lower-storey 203×203×46 UC: non-slender, LE=3.825m, Pc=1,195.111kN.

Both are S355 with py=355, governed by minor-axis curve c.

Both are adequate.

Misconceptions and checks

Use the same mechanism: Follow one strip of floor. At fixed area load, twice the tributary width gives twice the line load. An end reaction remains a concentrated force.

Apply the reasoning to this section’s data and conditions

  • Do not use 4 or 4.5m elevation heights when calculating tributary plan area.
  • Include roof load in the lower segment.
  • Reduce only imposed load and count the roof as instructed.
  • Do not add self-weight twice.
  • Use fixed/pinned recommended 0.85 for the lower column, not the upper one.

How the method transfers to a new variant

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Use the same mechanism: An eccentric beam reaction bends the column. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Apply the reasoning to this section’s data and conditions

  1. Trace the loads above each column segment and keep dead/imposed components separate.
  2. Read actual storey heights, section properties and end restraints in both axes.
  3. For simple construction derive nominal eccentric moments and share them by IL.
  4. Classify the section and form the correct section and member resistances.
  5. Apply only the prescribed load reductions and moment amplification rules.
  6. Check every storey segment and report both the governing check and source assumptions.

Prediction with explained answer

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Invented variant: imposed-load reduction is explicitly prohibited.

Does the selected lower column still pass?

Answer and reasoning

Lower force becomes 1.4×547.2+1.6×205.2=766.08+328.32=1,094.4kN.

Compare with 1,195.111kN: utilisation≈0.9157<1, so it still passes.

The roof segment is unchanged because it already had zero reduction.

Mechanism detailsEffective length and buckling axes2 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

Mechanism detailsEccentric reactions and stiffness sharing1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A beam reaction can act away from the column centre even at a nominally pinned beam connection.
  2. .

    Opposing reactions can cancel part of the signed moment, while both still add compression.

  3. The course simple model distributes the joint moment in proportion to of the columns above and below.
  4. Equal relevant stiffness gives half each.

    A roof joint with no upper column is a different case.

9. A repeatable exam sequence

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Apply the reasoning to this section’s data and conditions

  1. Identify simple or continuous construction, sway status, column segment, effective lengths in both axes, section and grade.
  2. Assemble factored axial load at each level; derive any eccentric moments or read given end moments.
  3. Read exact section properties and thickness-dependent pᵧ.

    Classify local elements under the applicable stress pattern.

  4. Compute capped section moment resistances and check the axial/biaxial section interaction.
  5. Calculate λx and λy, choose the proper curves, interpolate pc and form both axis resistances.
  6. For continuous construction obtain mx,my and mᴸᵀ from their separate tables.

    For simple construction set all three to 1.

  7. Use the correct amplified/first-order moments and elastic pᵧZ denominators for flexural interaction.
  8. Compute λᴸᵀ using the appropriate simple/continuous rule.

    Read pᵦ, calculate Mᵦ and check Eq.8.81.

  9. State all utilisation ratios and whether every required check is≤1.

Mechanism detailsEffective length and buckling axes2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

Practise this chapter: tutorials, assignments and past-paper answers →

Recent-paper practice for this chapter

Older-paper answers for this chapter (reference)