STEELWORK / CON4334
Worked examples

Tutorial 2 Q6: eccentric welds on two side plates

Diagrams, explanations and answers are presented in reading order. No playback or response is required.
All answers shownChinese–English terminology
Diagrams, explanations and answers are presented in reading order. No playback or response is required.

Determine the fillet weld leg for two 20mm side plates carrying characteristic dead 350kN plus imposed 300kN. The load is 200mm from the column face. Steel is S355 and electrode Class 42.

Original source: LectureNotes/Ch 2_Connection.pdf — p. 45, p. 48.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

Treat a weld group as lines

An eccentric force creates direct line force and torsional line force in the same weld group.

The four perimeter lines represent weld runs. The interior label says No weld here: the enclosed plate area is not weld length.
The four perimeter lines represent weld runs. The interior label says No weld here: the enclosed plate area is not weld length.

Prediction, then explanation. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Find the line centroid. Integrate squared distance along the effective lines. Add direct and torsional components at every candidate critical point.

J=∫r2 dl,qMx=−My/J,qMy=Mx/JJ=\int r^2\,dl,\qquad q_{Mx}=-My/J,\quad q_{My}=Mx/J

J is line polar inertia in mm³. x and y use mm. With M in kN·mm, q is line force in kN/mm.

Scope. A solid rectangle has area inertia in mm⁴ and is not this weld-line model. Missing weld sides change the centroid and integrals.

Check and takeaway. Compare the largest resultant line force with the selected throat resistance. Keep kN/mm distinct from total force in kN.

The weld resists through its throat

Convert a visible fillet leg into resistance per effective length.

The two outer sides are the legs. The shorter perpendicular line through the ideal triangle is the throat.
The two outer sides are the legs. The shorter perpendicular line through the ideal triangle is the throat.

Prediction, then explanation. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

For the course right-angle equal-leg fillet, take throat as 0.7 times leg. Multiply throat area per unit length by weld strength.

a=0.7s,qcap=0.7spw/1000a=0.7s,\qquad q_{cap}=0.7sp_w/1000

s and a are leg and throat in mm. pw is weld strength in N/mm². qcap is resistance in kN/mm.

Scope. Use effective length, the correct steel/electrode strength and permitted leg limits. Full-penetration butt welds use a different model.

Check and takeaway. Illustration: a 6 mm leg at 250 N/mm² gives 0.7(6)(250)/1000=1.05 kN/mm0.7(6)(250)/1000=1.05\,\mathrm{kN/mm}.

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Apply the reasoning to this section’s data and conditions

QuantitySource and derivation
Per-plate loadTwo identical side plates in the plan/front arrangement share the total equally.
Group sizeUse the labelled 200mm width and 300mm height for each four-sided weld group.
Load eccentricityFrom group centre to load: half the 200mm width plus 200mm beyond the face → e=300mm.
Weld model

Uniform all-round fillet represented as a closed line rectangle, as in Connection Example 7.

The plate area is not the weld-line area.

Size bounds20mm plate sets minimum 8mm under Table 9.1 and edge maximum 18mm under t−2.

Why this method applies

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Apply the reasoning to this section’s data and conditions

Two different 200mm labels play different roles.

One defines the rectangular group width.

The other begins at the column face.

The centroid is halfway across the group.

Therefore, the load arm is 300mm.

Calculate forces per length for one plate using half the load, then select a weld leg that meets resistance and detailing.

1. Factored force, centroid and moment

Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Keep load categories separate

A floor carries permanent material and changing occupancy loads. Find the design load for the stated check.

The two boxes show G and Q with their separate factors. The plus sign joins their factored values.
The two boxes show G and Q with their separate factors. The plus sign joins their factored values.

Prediction, then explanation. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

First convert mass to weight where required. Next collect G and Q in compatible units. Apply the combination specified by the course problem.

Wu=1.4G+1.6QW_u=1.4G+1.6Q

G is characteristic dead load; Q is characteristic imposed load. Wu is the design load for this course gravity combination.

Scope. This combination is not universal. Use the specified service load for deflection and the stated factors for other standards or cases.

Check and takeaway. Illustration: G = 10 kN and Q = 5 kN give 22 kN. Factoring their sum by one guessed factor loses the distinction.

Apply the reasoning to this section’s data and conditions

Total ultimate load: P=1.4×350+1.6×300=490+480=970kNEach side plate: P1=9702=485kNWeld group b=200mm, h=300mm. Total length: L=2(b+h)=1,000mmCoordinate distances from centroid to corner: x=100, y=150mm. e=200+b2=200+100=300mmM=P1e=485×300=145,500kN·mm

Equal sharing assumes the displayed symmetric plate pair and centred attachment of the applied load.

Using 485 with two weld groups already accounts for both plates.

Do not double the capacity again within a single group.

Mechanism detailsA weld group is a set of lines2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
  2. Use line lengths for centroid weighting.

    Line second moments have units .

    Add the parallel-axis terms.

  3. Direct force per length is .

    The eccentric moment adds tangential flow proportional to distance from the centroid.

  4. Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.

2. Derive line-weld polar inertia

Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Change the ruler, keep the quantity

A section table uses centimetres, but the strength calculation uses millimetres. The numbers must describe the same section.

Length1 factorArea2 factors3 factorsEach centimetre becomes ten millimetres.
In the diagram, the length, square and cube contain one, two and three length factors. Each factor changes when the ruler changes.

Prediction, then explanation. Would every property increase by ten? No. The exponent determines how many factors of ten are needed.

First identify the physical quantity. Next convert each length factor. Keep force and length conversions separate when converting a moment.

1 cmn=10n mmn,1 kN m=106 N mm1\,\mathrm{cm}^n=10^n\,\mathrm{mm}^n,\qquad 1\,\mathrm{kN\,m}=10^6\,\mathrm{N\,mm}

Here n is the length exponent: 2 for area, 3 for section modulus and 4 for second moment of area.

Scope. Changing units changes neither the load nor the section. A conversion factor cannot repair a formula for the wrong physical quantity.

Check and takeaway. Illustration: 2 cm4=20,000 mm42\,\mathrm{cm}^4=20{,}000\,\mathrm{mm}^4. The fourth power belongs to the unit, not the number 2.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Only the weld lines resist as weld

Imagine a wire rectangle: its empty middle is not more wire.

Only the weld lines resist as weld — Imagine a wire rectangle: its empty middle is not more wire.

Sketch, not to scale; use the original dimensions.

  1. Count only the weld runs actually shown.
  2. Use their total length and line second moments.
  3. Combine direct and torsional forces at the critical location.

Remember: Line second moments have units mm3; plate-area moments use mm4.

Related concept and full method

Ix=2(h312)+2b(h2)2=2×300312+2×200×1502=4,500,000+9,000,000=13,500,000mm3Iy=2(b312)+2h(b2)2=2×200312+2×300×1002=1,333,333.333+6,000,000=7,333,333.333mm3Ip=Ix+Iy=20,833,333.333mm3

Treat each side as a line.

A parallel-axis term is length times distance squared, giving units mm3.

This calculation finds force per unit weld length.

Do not use solid-plate inertia with units mm4.

Mechanism detailsA weld group is a set of lines2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
  2. Use line lengths for centroid weighting.

    Line second moments have units .

    Add the parallel-axis terms.

  3. Direct force per length is .

    The eccentric moment adds tangential flow proportional to distance from the centroid.

  4. Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.

3. Find the critical corner resultant per length

Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Add arrows before taking the magnitude

Walking east and walking north do not point in the same direction.

Add arrows before taking the magnitude — Walking east and walking north do not point in the same direction.

Sketch, not to scale; use the original dimensions.

  1. Choose signed horizontal and vertical directions.
  2. Add contributions along each direction separately.
  3. For perpendicular components, use the right-triangle resultant.

Remember: Check the corner where direct and torsional components reinforce each other.

Related concept and full method

Direct vertical force: qs=P1L=4851,000=0.485kNmmVertical torsional component: qTy=MxIp=145,500×10020,833,333.333=0.6984kNmmHorizontal torsional component: qTx=MyIp=145,500×15020,833,333.333=1.0476kNmmAt a corner where vertical components add: qvertical=0.485+0.6984=1.1834kNmmqmax=1.18342+1.04762=1.580475kNmm

At the opposite edge the vertical components subtract, giving a smaller resultant.

Top and bottom corners on the adding side have the same magnitude.

Mechanism detailsA weld group is a set of lines1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
  2. Use line lengths for centroid weighting.

    Line second moments have units .

    Add the parallel-axis terms.

  3. Direct force per length is .

    The eccentric moment adds tangential flow proportional to distance from the centroid.

  4. Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.

4. Select and verify the fillet leg

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why the weld throat is smaller than its leg

The shortest cut through the weld is thinner than the outside leg.

Why the weld throat is smaller than its leg — The shortest cut through the weld is thinner than the outside leg.

Sketch, not to scale; use the original dimensions.

  1. For the stated equal-leg 90° fillet, throat is approximately 0.7 × leg.
  2. Multiply throat area by the matching weld design strength.
  3. For force per length, use a one-millimetre weld strip.

Remember: Choose strength from both the steel grade and electrode class.

Related concept and full method

qcapacity=0.7spw1,000=0.175skNmmsrequired=1.5804750.175=9.031286mmFor each plate, select an all-round 10mm fillet weld. Resistance per unit length: 0.175×10=1.75kNmm>1.580475kNmmMinimum weld leg, selected size and plate-edge maximum: 8≤10≤20−2=18mm

The closed all-round group follows the source’s continuous line-weld model.

Do not treat its four connected sides as four separately terminated 180/280mm runs without revising the model.

Its 200 and 300mm sides exceed the minimum effective-length threshold max(4s,40)=40mm.

The selected size completes the requested weld-group resistance under the displayed four-sided, symmetric model.

Column local resistance is a separate check not requested or fully specified.

Mechanism detailsFrom fillet leg to effective throat1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. An equal-leg fillet between perpendicular plates has an approximately right-triangular section.
  2. For this geometry, throat .

    It is shorter than the leg.

  3. Effective resisting area = .

    With here, capacity per length is .

  4. Use the course end allowances, minimum size and length rules; increasing the geometric length alone does not resolve every detailing check.

Lecturer's answer

ItemLecturer's value
Design load1.4×350+1.6×300=970 kN1.4\times350+1.6\times300=970\text{ kN}, 485 kN per plate
Eccentricity / weld lengthe=300 mme=300\text{ mm}, L=2(200+300)=1000 mmL=2(200+300)=1000\text{ mm}
Corner radius / polar inertiar=180.3 mmr=180.3\text{ mm}, Ip=20.833×106 mm3I_p=20.833\times10^6\text{ mm}^3
Direct / torsional shearFs=0.485 kN/mmF_s=0.485\text{ kN/mm}, FT=1.259 kN/mmF_T=1.259\text{ kN/mm}
Resultant and leg lengthFR=1.581 kN/mmF_R=1.581\text{ kN/mm}, s=1.581×10000.7×250=9.0 mms=\dfrac{1.581\times1000}{0.7\times250}=9.0\text{ mm}

Conclusion: Use 10 mm fillet welds.

Source: Lecturer's tutorial solution, Ch 2, p. 7.

Result and concise exam wording

Add force components at each bolt

An in-plane load acts away from the bolt-group centre. Find the largest resultant bolt force.

The direct-force arrows are parallel. The moment-force arrows run tangentially around the bolt-group centre.
The direct-force arrows are parallel. The moment-force arrows run tangentially around the bolt-group centre.

Prediction, then explanation. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Locate the bolt-group centre and coordinates. Add horizontal components together and vertical components together before finding each resultant.

M=Pe,J=∑(xi2+yi2),FMx=−Myi/J,FMy=Mxi/JM=Pe,\quad J=\sum(x_i^2+y_i^2),\quad F_{Mx}=-My_i/J,\quad F_{My}=Mx_i/J

e, xi and yi use mm; J uses mm². With M in kN·mm, each moment-force component is in kN.

Scope. These expressions use the stated elastic, equal-bolt in-plane model. Out-of-plane tension and prying require another model.

Check and takeaway. Do not add force magnitudes before resolving directions. Two perpendicular forces of 3 and 4 kN give 5 kN, not 7 kN.

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Ask two separate design questions

Decide whether the check concerns failure or unacceptable behaviour during use.

The strength branch compares demand with resistance. The service branch compares displacement with its specified limit.
The strength branch compares demand with resistance. The service branch compares displacement with its specified limit.

Prediction, then explanation. A larger section may improve both results, but a pass on one branch does not prove a pass on the other.

ULS addresses relevant strength and stability failure modes. SLS addresses specified service conditions such as deflection.

demand≤resistance,δ≤δlimit\text{demand}\le\text{resistance},\qquad\delta\le\delta_{limit}

δ is the calculated displacement; δlimit is the permitted displacement. Both must use the same length unit.

Scope. Use each check’s own load combination and limit. A strength load factor does not change the physical stiffness.

Check and takeaway. Write separate conclusions for strength, stability and serviceability where requested. A single unexplained “safe” hides those distinctions.

Apply the reasoning to this section’s data and conditions

Total ULS load 970kN, per plate 485kN.

Rectangle 200×300mm,L=1,000mm, e=300mm, M=145,500kN·mm.

Ip,line=20.833333×106mm3.

Direct force 0.485, torsional vertical 0.6984 / horizontal 1.0476kNmm; qmax=1.580475kNmm.

s≥9.0313mm.

Select an all-around 10mm fillet weld on each plate.

Resistance 1.75kNmm, satisfying the 8–18mm size range.

Misconceptions and checks

Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Use the same mechanism: Add force components at each bolt. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Apply the reasoning to this section’s data and conditions

  • The load arm starts at the weld centroid, not the column face.
  • Split the force between the two plates once.
  • Do not use solid-rectangle inertia.
  • Vector-add direct and torsional components at the critical corner.

How the method transfers to a new variant

Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Use the same mechanism: Add force components at each bolt. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Apply the reasoning to this section’s data and conditions

  1. Establish the number of parallel weld groups and force per group.
  2. Locate the weld-line centroid and actual load eccentricity.
  3. Calculate total line length and polar line inertia.
  4. Resolve direct/torsional force-per-length components and find their maximum resultant.
  5. Round weld leg up and verify its capacity and allowed size range.

Prediction with explained answer

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Invented variant: the load is 200mm from the group centroid instead of the column face.

Find the required leg, keeping other data unchanged.

Answer and reasoning

M=485×200=97,000kN·mmTorsional vertical component 0.4656 and horizontal component 0.6984kNmm.

qmax=(0.485+0.4656)2+0.69842≈1.1795kNmmThe strength requirement gives a weld leg of approximately 6.74mm.

However, Table 9.1 for a 20mm plate still requires at least 8mm.

Therefore, select 8mm, resistance 1.4kNmm, conditional on the same all-around weld model.

Mechanism detailsA weld group is a set of lines2 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
  2. Use line lengths for centroid weighting.

    Line second moments have units .

    Add the parallel-axis terms.

  3. Direct force per length is .

    The eccentric moment adds tangential flow proportional to distance from the centroid.

  4. Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.