STEELWORK / CON4334
Mock solutions

Mock Q3: full solution and invented marking guide

Diagrams, explanations and answers are presented in reading order. No playback or response is required.
All answers shownChinese–English terminology
Diagrams, explanations and answers are presented in reading order. No playback or response is required.

Return to question.

All marking guidance is invented.

MOCK Q3 · braced non-sway column; all geometry repeated in the adjacent question.

Invented mock-question diagram: braced non-sway column.

The top arrow denotes design compression Fc=1000kN.

Section 254×254×89 UC; effective lengths about the two axes LE,x=LE,y=3500mm.

Uniform first-order moments Mx=80, My=40kN·m; amplification factors about the two axes 1.1.

Given mx=my=mLT=1 and already amplified MLT=88kN·m.

Schematic, not to scale; numerical labels govern.Open full-size image.

Lookup: Data File p.11, exact row 254×254×89 UC.

Read the dimensions/local ratios table and the properties table separately.

The x–x axis crosses the web horizontally; y–y passes vertically through its centre in the table sketch.

PropertyValue and units
Flange/web/root-to-root web depthT=17.3mm、t=10.3mm、d=200.3mm。
Local slendernessbT=7.41、dt=19.4。
Radii (converted from cm)rx=11.2×10=112mm;ry=6.55×10=65.5mm。
AreaA=113cm2=11300mm2。
Elastic moduliZx=1096cm3;Zy=379cm3。
Plastic moduliSx=1224cm3;Sy=575cm3。
LTB parameters

u=0.85, x=14.5.

Both dimensionless

(a) Classify before choosing resistance

Find which plate buckles first

Before using plastic bending resistance, check whether the flange and web can sustain the required stress distribution.

The short waves are local plate buckling. They differ from sideways movement of the whole member.
The short waves are local plate buckling. They differ from sideways movement of the whole member.

Prediction, then explanation. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Calculate the flange and web ratios separately. Compare each with the limits for its stress condition. The worse class governs.

ε=275/py\varepsilon=\sqrt{275/p_y}

py is the design yield strength in N/mm². ε is a dimensionless scale used in the supplied classification limits.

Scope. Pure bending and uniform compression use different web limits. Class 2 allows plastic resistance but not the Class 1 rotation capability.

Check and takeaway. A Class 1 web and Class 2 flange give a Class 2 section. Do not average the class numbers.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A thin part can wrinkle first

A thin plate may wrinkle before the whole steel member reaches its intended resistance.

A thin part can wrinkle first — A thin plate may wrinkle before the whole steel member reaches its intended resistance.

Sketch, not to scale; use the original dimensions.

  1. Check flange and web slenderness using their own definitions.
  2. Compare each ratio with the correct class limits.
  3. The element with the more restrictive class determines the section class.

Remember: Bending limits and uniform-compression limits are different.

Related concept and full method

T=17.3mm; use the S355 thickness band to select py=345Nmm2. ε=275345=0.892805
Flange bT=7.41; Class 1 limit 9ε=8.035248; Class 2 limit 10ε=8.928054. Flange is Class 1.
Web stress parameter: r1=Fdtpy=1000×1,000200.3×10.3×345Using 0≤r1≤1 is capped to give 1.000000. For any r1 in this range, the conservative Class 1 web limit is 40ε=35.712215. dt=19.4<35.712215. The web satisfies this stricter limit. Overall Class 1; use capped plastic section resistance.

The lecture’s Class 1 combined-stress web limit 80ε1+r1 cannot be below 40ε because r1≤1.

This check therefore avoids an unjustified plastic classification while remaining conservative.

The flange is checked independently.

Mechanism detailsWhy thin elements buckle locally1 concept · 3 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The flange outstand and web have different widths, thicknesses and edge support conditions.
  2. A thinner plate can wrinkle locally before the complete member loses stability.
  3. Class 1 allows plastic rotation.

    Class 2 reaches plastic resistance.

    Class 3 reaches elastic resistance.

    Class 4 requires effective properties.

  4. Check every relevant compression element with the supplied limits and stress distribution.

    The deformation shown is qualitative.

(b) Cross-section interaction

A strong cross-section can belong to an unstable member

A column carries axial compression and bending. Explain why more than one check is required.

The three boxes name separate checks: Section, Flexural and LTB. The bottom caption explains that passing one does not pass the others.
The three boxes name separate checks: Section, Flexural and LTB. The bottom caption explains that passing one does not pass the others.

Prediction, then explanation. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Separate cross-section, flexural-buckling and LTB interaction equations. Use each equation’s own denominators and first-order or amplified moments.

AgpyA_g p_y is a section axial resistance. AgpcA_g p_c is a member compression resistance. Elastic pyZp_y Z and prescribed McM_c are different bending denominators.

Scope. Preserve the course barred-moment definitions and Eq. 8.81 convention. Do not substitute plastic moduli into an elastic denominator.

Check and takeaway. Report each requested utilisation and the governing check. The largest properly calculated ratio identifies the closest limit.

Two simultaneous actions use one component

Check a component that carries shear and tension, or compression and bending, at the same time.

The bolt receives two labelled arrows: tension and shear. The caption requires both individual checks and the combined check.
The bolt receives two labelled arrows: tension and shear. The caption requires both individual checks and the combined check.

Prediction, then explanation. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

First apply the individual checks. Next use the exact combined equation and its definitions. Keep demands from the same load case.

FsPs+FtPnom≤1.4\frac{F_s}{P_s}+\frac{F_t}{P_{nom}}\le1.4

This is the course bolt interaction rule. Fs and Ft are bolt demands; Ps and Pnom are their specified resistance denominators.

Scope. The 1.4 limit and nominal tension denominator do not apply to column equations. Their limits and moment definitions are separate.

Check and takeaway. A sum above one can pass this bolt rule while still needing individual checks. A pass must name the actual equation used.

Apply the reasoning to this section’s data and conditions

Physical interpretation: The column needs more than one pass

A slice can be strong while the whole member still buckles.

The column needs more than one pass — A slice can be strong while the whole member still buckles.

Sketch, not to scale; use the original dimensions.

  1. Check cross-section compression plus bending.
  2. Then check the separate member-buckling expressions.
  3. Keep each moment, factor and resistance in its specified expression.

Remember: The three checks do not share interchangeable denominators.

Related concept and full method

At a cross section, compression and bending share the material.

Use amplified moments and capped plastic resistances.

The total must not exceed 1; all terms below are dimensionless.

Agpy=113×100×3451,000=3898.5kNMx,amp=1.1×80=88kN·mMy,amp=1.1×40=44kN·mMcx=min(345×12241,000,1.2×345×10961,000)=min(422.28,453.744)=422.28kN·mMcy=min(345×5751,000,1.2×345×3791,000)=min(198.375,156.906)=156.906kN·mSection interaction ratio: 10003898.5+88422.28+44156.906=0.745324Passes.

Mechanism detailsA strong slice can belong to an unstable member2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

(c) Flexural member interaction

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Check buckling about both axes

Determine which buckling direction limits the compressed member.

Compare the outlines labelled Straight and Bowed. The dashed line beside Bowed marks its original straight reference.
Compare the outlines labelled Straight and Bowed. The dashed line beside Bowed marks its original straight reference.

Prediction, then explanation. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Calculate slenderness about each axis. Select each axis’s curve from section type and thickness. Then obtain and compare the two compressive resistances.

λx=LEx/rx,λy=LEy/ry,Pc=pcAg\lambda_x=L_{Ex}/r_x,\quad\lambda_y=L_{Ey}/r_y,\qquad P_c=p_cA_g

Effective lengths and radii use mm. pc is compressive strength in N/mm²; Ag is gross area in mm²; Pc is in N.

Scope. Do not select the governing axis using radius alone. Effective length and buckling curve can differ. A combined column also needs interaction checks.

Check and takeaway. A short-section yield resistance is not the same as long-member buckling resistance. Keep py and pc distinct.

Use the same mechanism: Two simultaneous actions use one component. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why a long column can fail before crushing

Push a long thin ruler from both ends: it may bow sideways first.

Why a long column can fail before crushing — Push a long thin ruler from both ends: it may bow sideways first.

Sketch, not to scale; use the original dimensions.

  1. Find effective length and radius of gyration for each axis.
  2. Calculate slenderness for both directions.
  3. Use the appropriate buckling curve before forming resistance.

Remember: Compare the final resistances; slenderness alone may not identify the controlling axis.

Related concept and full method

Table 8.7: hot-rolled H-section (UC), maximum thickness ≤40mm, about the x axis use curve b, about the y axis use curve c.

Use the Data File p.8 py=345Nmm2 column.

The two axes use different curves, so slenderness alone cannot identify the governing axis.

Given effective length: LEx=LEy=3500mmλx=3500112=31.250000λy=350065.5=53.435115x axis uses curve b: 30 gives 325,35 gives 318Nmm2. Interpolation fraction: 31.250000−3035−30=0.250000pc=325+0.250000×(318−325)=323.250000Nmm2y axis uses curve c: 52 gives 263,54 gives 258Nmm2. Interpolation fraction: 53.435115−5254−52=0.717557pc=263+0.717557×(258−263)=259.412214Nmm2Pcx=Apcx10=113×323.25000010=3652.725000kNPcy=113×259.41221410=2931.358015kNPc=min(Pcx,Pcy)=2931.358015kN

Member interaction uses elastic moment denominators pᵧZ, even when the cross-section check used plastic moduli.

Use amplified moments here.

Mex=345×10961,000=378.12kN·mMey=345×3791,000=130.755kN·mFPc+mxMx,ampMex+myMy,ampMey=10002931.358015+1×88378.12+1×44130.755=0.910376Passes.

Mechanism detailsA strong slice can belong to an unstable member5 concepts · 4 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

(c) LTB interaction

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Vertical bending can trigger sideways motion

A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.

The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.
The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.

Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.

λ=LE/ry,Mb=pbSx  (Class 1/2),mLTMmax≤Mb\lambda=L_E/r_y,\qquad M_b=p_bS_x\;\text{(Class 1/2)},\qquad m_{LT}M_{max}\le M_b

LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.

Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.

Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.

Use the same mechanism: Two simultaneous actions use one component. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A beam can escape sideways

The compressed flange can move sideways while the section twists.

A beam can escape sideways — The compressed flange can move sideways while the section twists.

Sketch, not to scale; use the original dimensions.

  1. Divide the beam at effective lateral restraints.
  2. Use each segment’s effective length to obtain its buckling resistance.
  3. Compare that resistance with the segment’s equivalent moment demand.

Remember: A section bending check alone does not check lateral-torsional buckling.

Related concept and full method

Continuous/non-sway member: Class 1/2 gives βW=1.

Use the full u–v calculation with the stated effective length.

λ=LEry=350065.5=53.435115v=[1+0.05(λx)2]−14=[1+0.05(53.43511514.5)2]−14=0.878487λLT=uvλβW=0.85×0.878487×53.435115×1=39.900763

Read Data File p.5 Table 8.3a, pᵧ345 column:

35 gives 332,40 gives 317Nmm2. Interpolation fraction: 39.900763−3540−35=0.980153pb=332+0.980153×(317−332)=317.297710Nmm2Mb=pbSx=317.297710×12241,000=388.372397kN·m

Course Eq.8.81 uses first-order minor-axis moment in its last term.

Mᴸᵀ is the specified amplified major-axis value.

Do not amplify it twice.

The axial denominator is Pcy.

FPcy+mLTMLTMb+myMy,firstMey=10002931.358015+1×88388.372397+1×40130.755=0.873641Passes.

Mechanism detailsA strong slice can belong to an unstable member5 concepts · 4 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

Compact script and invented marking guide

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Apply the reasoning to this section’s data and conditions

py=345Nmm2; Pcx=3652.725kN, Pcy=2931.358kN; Mcx=422.280kN·m, Mcy=156.906kN·m; Mb=388.372kN·m.

Interaction ratios: section 0.745324, flexural buckling 0.910376, axial force/LTB 0.873641.

All three requested strength checks pass.

Invented credit: classification 4; section properties/amplification 3 and interaction 3; curves/slenderness 4, compression interpolation 4, flexural equation/result 4, accurate LTB calculation 5, second interaction/conclusion 3. Do not multiply the supplied 88kN·m by 1.1 again.

Mechanism detailsFollow the calculation sequence2 concepts · 6 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Locate the load, supports, connection geometry and any stated assumptions.
  2. Keep given values, table lookups and calculated values distinct; reconcile their units.
  3. The calculation player steps through the existing expressions in their original order.
  4. Compare demand with resistance or the relevant limit.

    Keep missing inputs and conditional conclusions explicit.