STEELWORK / CON4334
Worked examples

2023 BQ2(b): ten bolts in an eccentric bracket

Diagrams, explanations and answers are presented in reading order. No playback or response is required.
All answers shownChinese–English terminology
Diagrams, explanations and answers are presented in reading order. No playback or response is required.

Find shear and tension capacities, then check tenM20 Grade 8.8 bolts attaching the S355 bracket carrying 350kN design load at 300mm eccentricity. The end plate is 16mm thick and the supporting section 305×305×137 UC.

Original source: Pastpaper/22ENGTY033.pdf — p. 4.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

An eccentric bracket pulls bolts differently

An out-of-plane moment rotates the bracket about the stated pivot. Determine the bolt tension pattern.

The pivot is the compression reference. Bolts farther from it have longer lever arms in the course elastic model.
The pivot is the compression reference. Bolts farther from it have longer lever arms in the course elastic model.

Prediction, then explanation. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Use compatibility to relate tension to distance. Moment equilibrium then determines the proportionality factor.

Ft,i=Myi∑yj2F_{t,i}=\frac{My_i}{\sum y_j^2}

M is moment in kN·mm. yi is distance from the stated pivot in mm. Ft,i is tension in kN.

Scope. Apply only to the stated active bolt set and pivot model. Flexible plates can create prying; use the supplied assumptions and resistance definitions.

Check and takeaway. A bolt’s lever arm is measured from the pivot used in the equation. It is not automatically its distance from the group centroid.

A bolt diameter is not a hole diameter

Check that bolts fit and leave enough material between holes and plate boundaries.

pdd₀Clear ligament
The inner circle represents bolt diameter d. The outer circle represents hole diameter d₀. Pitch and gauge join hole centres.

Prediction, then explanation. At fixed pitch, a larger hole leaves a shorter clear ligament. Increasing bolt diameter may also increase minimum edge-distance requirements.

Measure pitch along the bolt line and gauge across lines. Distinguish end distance along the load from edge distance across it.

lc=p−d0l_c=p-d_0

lc is clear ligament between holes; p is centre-to-centre pitch; d₀ is hole diameter. All use mm.

Scope. Apply the supplied edge-preparation and minimum/maximum spacing rules. Passing a bearing calculation does not prove the layout passes.

Check and takeaway. For pitch 60 mm and hole diameter 22 mm, the ligament is 38 mm. Using a 20 mm bolt diameter here gives the wrong ligament.

Apply the reasoning to this section’s data and conditions

InputOrigin/model
LoadGiven designed 350kN; no 1.4/1.6 factor.
FastenersM20 As=245mm2; Grade 8.8 ps=375, pt=560Nmm2; nominal tension 0.8Aspt.
Approximate pivotUse the course model rotating about the lowest bolt row: y=0,70,140,210,280mm, with two bolts per row.
Prying applicability

Supporting UC flange widthB309.2 mm from Data File p.11.

Bolt gaugeG is not dimensioned, so G≤0.55B cannot be independently verified.

Why this method applies

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Test every possible fracture cut

Find the remaining steel area across a candidate tension-failure path.

The dashed fracture line crosses two hole centres. Subtract only the holes crossed by that candidate line.
The dashed fracture line crosses two hole centres. Subtract only the holes crossed by that candidate line.

Prediction, then explanation. At fixed plate size, larger holes reduce the straight-path net area. A diagonal path needs its own stagger correction.

Subtract the hole widths crossed by the path, then multiply by thickness. Compare all plausible paths using the applicable course rule.

An=(b−nd0)tA_n=(b-nd_0)t

An is net area in mm²; b is plate width; d₀ is hole diameter; t is thickness, all in mm. n counts holes on this straight path.

Scope. This expression is for a straight cut. Effective area can require further shear-lag rules. Gross, net and effective areas must remain distinct.

Check and takeaway. Use the hole diameter, not the bolt diameter, when removing missing steel. The plate contains a hole, not solid steel around the bolt shank.

Apply the reasoning to this section’s data and conditions

The load tends to peel the upper plate away while every bolt also carries direct shear.

Calculate nominal tension resistance for the course simplified no-prying treatment, then compare both individual actions and the combined ratio.

The course combined limit is 1.4, not 1.

(i) Individual bolt capacities —5 printed marks

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Count cuts through each loaded bolt

Find how many shear planes transfer the force through one side of the connection.

The middle plate moves against two cover plates. The two interfaces cut each bolt at two planes.
The middle plate moves against two cover plates. The two interfaces cut each bolt at two planes.

Prediction, then explanation. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Select the area at the actual shear plane. Multiply by bolt shear strength. Count only the bolts and planes in the same transfer stage.

Ps=psAs,Pgroup=nbnsPsP_s=p_sA_s,\qquad P_{group}=n_b n_s P_s

ps is bolt shear strength in N/mm²; As is the appropriate area in mm². nb counts bolts; ns counts equally loaded shear planes.

Scope. Use the thread area when threads cross the plane as required. Check bearing, plate failure and detailing separately.

Check and takeaway. Both halves of a butt splice carry the full transmitted force in sequence. Counting both halves together would double the apparent resistance.

Two simultaneous actions use one component

Check a component that carries shear and tension, or compression and bending, at the same time.

The bolt receives two labelled arrows: tension and shear. The caption requires both individual checks and the combined check.
The bolt receives two labelled arrows: tension and shear. The caption requires both individual checks and the combined check.

Prediction, then explanation. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

First apply the individual checks. Next use the exact combined equation and its definitions. Keep demands from the same load case.

FsPs+FtPnom≤1.4\frac{F_s}{P_s}+\frac{F_t}{P_{nom}}\le1.4

This is the course bolt interaction rule. Fs and Ft are bolt demands; Ps and Pnom are their specified resistance denominators.

Scope. The 1.4 limit and nominal tension denominator do not apply to column equations. Their limits and moment definitions are separate.

Check and takeaway. A sum above one can pass this bolt rule while still needing individual checks. A pass must name the actual equation used.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Count where the bolt can be sheared

The plate interfaces are the places trying to cut across the bolt.

Count where the bolt can be sheared — The plate interfaces are the places trying to cut across the bolt.

Sketch, not to scale; use the original dimensions.

  1. Count actual loaded shear planes, not merely visible plates.
  2. Choose shank or threaded area for the plane concerned.
  3. Compare group resistance with the force that group transfers.

Remember: Bolts on opposite sides of a splice do not all act in parallel.

Related concept and full method

Single-shear resistance: Ps=Asps1,000=245×3751,000=91.875kN per bolt. Basic tension resistance: Pt=Aspt1,000=245×5601,000=137.2kNNominal tension resistance for the course reduced-resistance treatment: Pnom=0.8Pt=0.8×137.2=109.76kN

State both 137.2 and 109.76 and identify their meanings.

The following lecture-style interaction uses 109.76.

The one end-plate/column interface is single shear.

Mechanism detailsOut-of-plane bolt tension and prying3 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A bracket moment can create compression at the plate contact and tension in the bolt rows.
  2. The original assumed pivot/compression line determines each row distance.
  3. Under the elastic row model, a farther tension row attracts more tension.

    Direct shear may act simultaneously.

  4. Flexible plates can add prying force.

    Use nominal tension and interaction rules exactly as specified by the course.

(ii) Forces in the governing bolt and adequacy —10 printed marks

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Use the same mechanism: Count cuts through each loaded bolt. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Use the same mechanism: Two simultaneous actions use one component. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why the top bolt row is pulled hardest

The bracket tries to peel away from the support about the assumed contact line.

Why the top bolt row is pulled hardest — The bracket tries to peel away from the support about the assumed contact line.

Sketch, not to scale; use the original dimensions.

  1. Use the rotation/contact line assumed by the course model.
  2. Measure each bolt row’s distance from that line.
  3. Check maximum tension, direct shear and their interaction.

Remember: A row at the pivot can still carry direct shear.

Related concept and full method

Physical interpretation: Two passing checks may still interact

One bolt is doing two jobs at the same time.

Two passing checks may still interact — One bolt is doing two jobs at the same time.

Sketch, not to scale; use the original dimensions.

  1. Check shear on its own and tension on its own.
  2. Calculate the course’s combined-action expression.
  3. Apply its own limit, not a limit borrowed from columns.

Remember: The supplied bolt interaction limit of 1.4 does not replace the individual checks.

Related concept and full method

M=Pe=350×300=105,000kN·mmΣy2=2(02+702+1402+2102+2802)=2(0+4,900+19,600+44,100+78,400)=294,000mm2Ft,max=MymaxΣy2=105,000×280294,000=100kNDirect shear: Fs=Pn=35010=35kNIndividual shear check: 35<91.875: passes. Individual tension check: 100<109.76: passes. Interaction: FsPs+FtPnom=3591.875+100109.76=0.380952+0.911079=1.292031<1.4Passes.

The bottom row has zero moment-induced tension in this approximation but still carries 35kN shear.

This is why the tension sum uses squared row distances, while direct shear simply divides by 10.

Flange transverse-spacing condition for no prying: G≤0.55B=0.55×309.2=170.06mm

Mechanism detailsOut-of-plane bolt tension and prying4 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A bracket moment can create compression at the plate contact and tension in the bolt rows.
  2. The original assumed pivot/compression line determines each row distance.
  3. Under the elastic row model, a farther tension row attracts more tension.

    Direct shear may act simultaneously.

  4. Flexible plates can add prying force.

    Use nominal tension and interaction rules exactly as specified by the course.

Result and concise exam wording

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Use the same mechanism: Two simultaneous actions use one component. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

Apply the reasoning to this section’s data and conditions

(i) Each M20: Ps=91.875, Pt=137.2, Pnom=109.76kN. (ii) P=350, e=300, M=105,000kN·mm; Σy2=294,000mm2; Ft,max=100, Fs=35kN.

Both individual limits pass; interaction 1.292031<1.4.

This conclusion is conditional on the course no-prying model.

Missing transverse spacing prevents verification of the required G≤170.06mm.

Misconceptions and checks

Add force components at each bolt

An in-plane load acts away from the bolt-group centre. Find the largest resultant bolt force.

The direct-force arrows are parallel. The moment-force arrows run tangentially around the bolt-group centre.
The direct-force arrows are parallel. The moment-force arrows run tangentially around the bolt-group centre.

Prediction, then explanation. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Locate the bolt-group centre and coordinates. Add horizontal components together and vertical components together before finding each resultant.

M=Pe,J=∑(xi2+yi2),FMx=−Myi/J,FMy=Mxi/JM=Pe,\quad J=\sum(x_i^2+y_i^2),\quad F_{Mx}=-My_i/J,\quad F_{My}=Mx_i/J

e, xi and yi use mm; J uses mm². With M in kN·mm, each moment-force component is in kN.

Scope. These expressions use the stated elastic, equal-bolt in-plane model. Out-of-plane tension and prying require another model.

Check and takeaway. Do not add force magnitudes before resolving directions. Two perpendicular forces of 3 and 4 kN give 5 kN, not 7 kN.

Apply the reasoning to this section’s data and conditions

  • Count five rows, not six; top 70 is a margin.
  • Σy2 Count two bolts per row.
  • Do not put all 350kN on the top bolt.
  • Do not use 1 as the combined-ratio limit.

How the method transfers to a new variant

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Use the same mechanism: Two simultaneous actions use one component. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

Apply the reasoning to this section’s data and conditions

  1. Identify bolt count, spacing and the stated approximate rotation line.
  2. Compute shear and nominal tension resistances.
  3. Calculate Pe and Σy2, then the top-row tension.
  4. Check both individual actions and the 1.4 interaction.
  5. State whether the no-prying prerequisites are actually specified.

Prediction with explained answer

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Ask two separate design questions

Decide whether the check concerns failure or unacceptable behaviour during use.

The strength branch compares demand with resistance. The service branch compares displacement with its specified limit.
The strength branch compares demand with resistance. The service branch compares displacement with its specified limit.

Prediction, then explanation. A larger section may improve both results, but a pass on one branch does not prove a pass on the other.

ULS addresses relevant strength and stability failure modes. SLS addresses specified service conditions such as deflection.

demand≤resistance,δ≤δlimit\text{demand}\le\text{resistance},\qquad\delta\le\delta_{limit}

δ is the calculated displacement; δlimit is the permitted displacement. Both must use the same length unit.

Scope. Use each check’s own load combination and limit. A strength load factor does not change the physical stiffness.

Check and takeaway. Write separate conclusions for strength, stability and serviceability where requested. A single unexplained “safe” hides those distinctions.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Invented variant: eccentricity increases to 350mm with the same 350kN load.

Does the nominal tension check pass?

Answer and reasoning

Ft,max scales with e:100×350300=116.666667kN>109.76, so individual tension fails.

You must reject it even if considering only a combined sum might seem acceptable; all three bolt conditions are compulsory.

Mechanism detailsOut-of-plane bolt tension and prying2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A bracket moment can create compression at the plate contact and tension in the bolt rows.
  2. The original assumed pivot/compression line determines each row distance.
  3. Under the elastic row model, a farther tension row attracts more tension.

    Direct shear may act simultaneously.

  4. Flexible plates can add prying force.

    Use nominal tension and interaction rules exactly as specified by the course.