STEELWORK / CON4334
Worked examples

Assignment 2 Q2: an intermediate restraint at an off-centre load

Diagrams, explanations and answers are presented in reading order. No playback or response is required.
All answers shownChinese–English terminology
Diagrams, explanations and answers are presented in reading order. No playback or response is required.

For 356×171×67 UB S355, assumed Class 1, find support reactions and draw annotated SFD/BMD under ultimateP60 kN at 5m from A plus full-span 4kNm UDL over 8m. Check segmentAB LTB using accurateu andv, and discuss removing restraintB.

Original source: Assignment/AY2627s 1-CON4334-Assignment 2.pdf — p. 2.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

Vertical bending can trigger sideways motion

A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.

The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.
The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.

Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.

λ=LE/ry,Mb=pbSx  (Class 1/2),mLTMmax≤Mb\lambda=L_E/r_y,\qquad M_b=p_bS_x\;\text{(Class 1/2)},\qquad m_{LT}M_{max}\le M_b

LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.

Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.

Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.

Change the ruler, keep the quantity

A section table uses centimetres, but the strength calculation uses millimetres. The numbers must describe the same section.

Length1 factorArea2 factors3 factorsEach centimetre becomes ten millimetres.
In the diagram, the length, square and cube contain one, two and three length factors. Each factor changes when the ruler changes.

Prediction, then explanation. Would every property increase by ten? No. The exponent determines how many factors of ten are needed.

First identify the physical quantity. Next convert each length factor. Keep force and length conversions separate when converting a moment.

1 cmn=10n mmn,1 kN m=106 N mm1\,\mathrm{cm}^n=10^n\,\mathrm{mm}^n,\qquad 1\,\mathrm{kN\,m}=10^6\,\mathrm{N\,mm}

Here n is the length exponent: 2 for area, 3 for section modulus and 4 for second moment of area.

Scope. Changing units changes neither the load nor the section. A conversion factor cannot repair a formula for the wrong physical quantity.

Check and takeaway. Illustration: 2 cm4=20,000 mm42\,\mathrm{cm}^4=20{,}000\,\mathrm{mm}^4. The fourth power belongs to the unit, not the number 2.

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Apply the reasoning to this section’s data and conditions

Lookup: Data File pp.9–10, exact 356×171×67 UB row.

Dimensions on p.9; properties on p.10.

D is overall depth.

d is the clear web depth between root fillets, not the nominal designation.

PropertyLookup value / conversion
DimensionsD363.4, web t 9.1, flange T15.7, root r 10.2, clear d 311.6, all mm
Local ratiosbT=5.52;dt=34.2。
Major-axis propertiesIx=19460cm4=1.946×108mm4; Zx=1071cm3; Sx=1211cm3.
LTB propertiesry=3.99cm=39.9mm; u=0.886; torsional index x=24.4.

Why this method applies

Balance the isolated beam

Find the two vertical reactions before calculating internal shear or moment.

A / RₐB / RᵦPaL
A and B are vertical supports. The downward load acts at distance a from A. Its distance from B is L − a.

Prediction, then explanation. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Take moments about A. Reaction A has zero lever arm there. Then use vertical force balance to find reaction A.

RBL=Pa,RA+RB=PR_B L=Pa,\qquad R_A+R_B=P

P, RA and RB are forces in kN. L is support spacing and a is load position, both in m.

Scope. These expressions describe one point load on a simply supported beam. Add other loads through equilibrium; keep their actual positions.

Check and takeaway. Illustration: P = 60 kN, L = 6 m and a = 2 m give RB = 20 kN and RA = 40 kN.

Apply the reasoning to this section’s data and conditions

Vertical equilibrium gives one simply supported 8m beam.

Lateral stability is assessed over shorter segments.

Keep these two models distinct:5m is the AB stability length, not a 5m simply supported vertical-load span.

(a) Support reactions

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why reactions balance the loads

Think of a seesaw that must neither fall nor turn.

Why reactions balance the loads — Think of a seesaw that must neither fall nor turn.

Sketch, not to scale; use the original dimensions.

  1. Upward and downward forces must balance.
  2. Take moments about a support to eliminate its reaction.
  3. Use perpendicular distance from the point to the force line.

Remember: A lateral restraint is not automatically a vertical support.

Related concept and full method

Total downward force: 4×8+60=92kNUDL resultant 32kN acts at distance 4m from A. Taking moments about A: 8RC=32×4+60×5=128+300=428RC=4288=53.5kNRA=92−53.5=38.5kNCheck moments about C: 38.5×8=32×4+60×3=308kN·m

Mechanism detailsBalance reactions and moments1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. This demonstrator is a simply supported 6 m beam with a 60 kN point load.

    It is not the page’s original loading diagram.

  2. .

    Moving the load towards B increases .

  3. .

    The two upward reactions must sum to P.

  4. With the load at midspan, .

    End couples, UDLs and overhangs require their own equilibrium terms.

(b) Annotated shear and bending diagrams

A cut reveals the internal actions

Find where the beam moment is largest. A large load arrow alone does not locate that point.

The dashed imaginary cut separates two beam pieces. The opposing arrows represent the shear action between those pieces.
The dashed imaginary cut separates two beam pieces. The opposing arrows represent the shear action between those pieces.

Prediction, then explanation. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Balance the forces on the cut piece to get V. Balance their moments about the cut to get M. Evaluate each load region separately.

V(x)=RA−wx,M(x)=RAx−wx22V(x)=R_A-wx,\qquad M(x)=R_Ax-\frac{wx^2}{2}

x and L use m; w uses kN/m; V uses kN; M uses kN·m. These lines apply before any point load.

Scope. A point load adds a shear jump. A concentrated couple adds a moment jump. Check load points, supports and overhang roots too.

Check and takeaway. A UDL gives a sloping shear line and a curved moment line. A flat moment diagram therefore cannot represent a loaded UDL region.

Apply the reasoning to this section’s data and conditions

x is in metres from A; sagging moment is positive.0≤x≤5: V=38.5−4xkNM=38.5x−2x2kN·m5≤x≤8: V=38.5−4x−60kNM=38.5x−2x2−60(x−5)kN·mShear end values: V(A+)=38.5V(B−)=18.5V(B+)=−41.5V(C−)=−53.5kNMoment end values: M(A)=0M(B)=38.5×5−2×25=142.5kN·mM(C)=0Shear changes sign at B, so the maximum there is M=142.5kN·m.
Calculated shear and bending diagrams with labelled support/load ordinates; positive values upward. All values are repeated in the working.

This is a teaching diagram drawn from the calculation, not an original source image.

Positions are measured in m.

V is measured in kN.

M is measured in kN·m.Open full-size image.

The SFD slopes downward at 4kN per metre on both intervals.

Its jump atB is 60kN.

The BMD is parabolic between loads and has a change of slope atB.

It has no jump because there is no applied point couple.

Mechanism detailsBuild the shear and moment diagrams1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For the illustrative 60 kN point load on a 6 m simply supported beam, balance the reactions before making a cut.
  2. and before the point load.

    Moment grows linearly.

  3. Shear jumps down by P.

    To its right, and .

  4. For this case, moment is continuous and returns to zero at B.

    A concentrated applied couple instead creates a moment jump.

(c) AB lateral-torsional buckling using accurate parameters

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Find which plate buckles first

Before using plastic bending resistance, check whether the flange and web can sustain the required stress distribution.

The short waves are local plate buckling. They differ from sideways movement of the whole member.
The short waves are local plate buckling. They differ from sideways movement of the whole member.

Prediction, then explanation. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Calculate the flange and web ratios separately. Compare each with the limits for its stress condition. The worse class governs.

ε=275/py\varepsilon=\sqrt{275/p_y}

py is the design yield strength in N/mm². ε is a dimensionless scale used in the supplied classification limits.

Scope. Pure bending and uniform compression use different web limits. Class 2 allows plastic resistance but not the Class 1 rotation capability.

Check and takeaway. A Class 1 web and Class 2 flange give a Class 2 section. Do not average the class numbers.

Moment shape matters within one segment

Represent a nonuniform moment distribution in the applicable member-buckling equation.

The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.
The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.

Prediction, then explanation. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Evaluate moments from the true whole-beam analysis at the required positions. Apply the exact table’s weights, signs and lower bound.

mLT is an LTB factor. mx and my belong to the specified flexural checks. They are not interchangeable.

Scope. Some rules use magnitudes; others require signed ordinates. A factor does not reduce the actual moment used in a local section check.

Check and takeaway. Measure quarter points from the segment start, not automatically from the beam’s left support.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A beam can escape sideways

The compressed flange can move sideways while the section twists.

A beam can escape sideways — The compressed flange can move sideways while the section twists.

Sketch, not to scale; use the original dimensions.

  1. Divide the beam at effective lateral restraints.
  2. Use each segment’s effective length to obtain its buckling resistance.
  3. Compare that resistance with the segment’s equivalent moment demand.

Remember: A section bending check alone does not check lateral-torsional buckling.

Related concept and full method

S355, flange T=15.7mm, giving py=355Nmm2. ε=275355=0.880141Flange: bT=5.52<9ε=7.921268Web in bending: dt=34.2<80ε=70.411267Both are Class 1, so βW=1; plastic bending resistance is permitted.dt=34.2<70ε=61.609858No separate shear-buckling calculation is needed under the course limit.

Within the 5m AB segment, quarter points are 1.25,2.5 and 3.75 m fromA.

The B point load acts at the segment end.

It is accounted for throughRA and the maximum moment.

M2=38.5×1.25−2×1.252=45kN·mM3=38.5×2.5−2×2.52=83.75kN·mM4=38.5×3.75−2×3.752=116.25kN·mmLT=0.2+0.15×45+0.5×83.75+0.15×116.25142.5=0.663596>0.44Equivalent demand 94.562500kN·m.

Normal-load effective length is the given segment length.

All quantities in λ and λᴸᵀ are dimensionless.

This Class 1 section has βW=1.

λ=LEry=500039.9=125.313283v=[1+0.05(λx)2]−14=[1+0.05(125.31328324.4)2]−14=0.810370λLT=uvλβW=0.886×0.810370×125.313283×1=89.973415

Table 8.3a, Data File p.5, pᵧ355 column:

85 row gives 175; 90 row gives 162Nmm2. Interpolation fraction: 89.973415−8590−85=0.994683pb=175+0.994683×(162−175)=162.069120Nmm2Mb=pbSx1,000=162.069120×12111,000=196.265704kN·mEquivalent uniform moment demand: mLTMmax=94.562500kN·mUtilisation: 94.562500196.265704=0.481809Passes.

AB passes under the stated normal-load/LE5 m assumption.

The u value is 0.886 from this exact UB row.

v is calculated, not assumed 1.

Mechanism detailsA beam bends sideways and twists5 concepts · 5 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For the illustrated sagging beam the top flange is compressed.
  2. The unrestrained compression flange can move sideways while the complete cross-section twists.
  3. Only effective restraints divide the member into unbraced segments.

    They do not automatically add vertical supports.

  4. Use the segment effective length, section properties and matching moment factor.

    This is an exaggerated mode shape, not a calculated displacement.

(d) Removing B changes stability but not vertical actions

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A support stops only certain movements

Holding a ruler up does not necessarily stop it sliding sideways or twisting.

A support stops only certain movements — Holding a ruler up does not necessarily stop it sliding sideways or twisting.

Sketch, not to scale; use the original dimensions.

  1. Identify vertical support, lateral restraint and torsional restraint separately.
  2. Find which flange is in compression in each region.
  3. Use only restraints actually provided by the question.

Remember: An extra side restraint does not create a new vertical reaction.

Related concept and full method

Without the effective lateral restraint atB, the unrestrained segment becomes the full 8m betweenA andC.

The point load remains at 5m.

Therefore, the reactions and vertical SFD/BMD remain unchanged.

Longer LE increases slenderness and reduces buckling resistance.

Full-span quarter points: x=2,4,6m. M(2)=38.5×2−2×22=69kN·mM(4)=38.5×4−2×42=122kN·mM(6)=38.5×6−2×62−60×1=99kN·mmLT=0.2+0.15×69+0.5×122+0.15×99142.5=0.804912New equivalent demand 114.700000kN·m.

Normal-load effective length is the given segment length.

All quantities in λ and λᴸᵀ are dimensionless.

This Class 1 section has βW=1.

λ=LEry=800039.9=200.501253v=[1+0.05(λx)2]−14=[1+0.05(200.50125324.4)2]−14=0.691395λLT=uvλβW=0.886×0.691395×200.501253×1=122.822299

Table 8.3a, Data File p.5, pᵧ355 column:

120 row gives 104; 125 row gives 97Nmm2. Interpolation fraction: 122.822299−120125−120=0.564460pb=104+0.564460×(97−104)=100.048781Nmm2Mb=pbSx1,000=100.048781×12111,000=121.159074kN·mEquivalent uniform moment demand: mLTMmax=114.700000kN·mUtilisation: 114.700000121.159074=0.946689Passes.

The member remains a numerical narrow pass under the sameLE=actual/normal-load assumptions, but stability margin is substantially reduced.

It is wrong to say that removing a restraint always forces failure.

It always requires a new check.

Other beam checks are outside the requested LTB calculation.

Mechanism detailsA beam bends sideways and twists5 concepts · 4 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For the illustrated sagging beam the top flange is compressed.
  2. The unrestrained compression flange can move sideways while the complete cross-section twists.
  3. Only effective restraints divide the member into unbraced segments.

    They do not automatically add vertical supports.

  4. Use the segment effective length, section properties and matching moment factor.

    This is an exaggerated mode shape, not a calculated displacement.

Result and concise exam wording

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

RA=38.5, RC=53.5kN.

Shear values: +38.5,+18.5,−41.5,−53.5; moment values: 0,142.5,0.

AB: λ=125.313283, v=0.810370, λLT=89.973415, pb=162.069120, Mb=196.265704kN·m; demand 94.5625: passes.

Remove B: λ=200.501253, λLT=122.822299, Mb=121.159074kN·m; full-span demand 114.7: still just passes.

These LTB results assume normal loading and that LE equals the distance between restraints.

Misconceptions and checks

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Apply the reasoning to this section’s data and conditions

  • Do not make B a vertical support.
  • Do not use full-span quarter positions for AB.
  • Do not discard the UDL in the moment ordinates.
  • Do not state failure after restraint removal without recalculating.

How the method transfers to a new variant

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

  1. Solve the original vertical system first.
  2. Mark lateral restraint positions separately.
  3. Find each segment’s maximum and local quarter moments.
  4. Readu,x,ry and calculatev without early rounding.
  5. Change both effective length and moment factor when a restraint is removed.

Prediction with explained answer

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Keep load categories separate

A floor carries permanent material and changing occupancy loads. Find the design load for the stated check.

The two boxes show G and Q with their separate factors. The plus sign joins their factored values.
The two boxes show G and Q with their separate factors. The plus sign joins their factored values.

Prediction, then explanation. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

First convert mass to weight where required. Next collect G and Q in compatible units. Apply the combination specified by the course problem.

Wu=1.4G+1.6QW_u=1.4G+1.6Q

G is characteristic dead load; Q is characteristic imposed load. Wu is the design load for this course gravity combination.

Scope. This combination is not universal. Use the specified service load for deflection and the stated factors for other standards or cases.

Check and takeaway. Illustration: G = 10 kN and Q = 5 kN give 22 kN. Factoring their sum by one guessed factor loses the distinction.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Invented variant: all ultimate loads increase 5% after restraintB is removed.

Does the full-span LTB check still pass?

Answer and reasoning

Yes, narrowly.

Demand becomes 1.05×114.7=120.435kN·m, below 121.159074.

At 6% increase, demand 121.582kN·m exceeds 121.159074 and fails.

Maximum proportional increase≈121.159074114.7−1=5.6313%.

This comparison uses the original section and the stated stability assumptions.

Mechanism detailsA beam bends sideways and twists2 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For the illustrated sagging beam the top flange is compressed.
  2. The unrestrained compression flange can move sideways while the complete cross-section twists.
  3. Only effective restraints divide the member into unbraced segments.

    They do not automatically add vertical supports.

  4. Use the segment effective length, section properties and matching moment factor.

    This is an exaggerated mode shape, not a calculated displacement.