STEELWORK / CON4334
Worked examples

2024 BQ4: uneven point loads and segment-by-segment LTB

Diagrams, explanations and answers are presented in reading order. No playback or response is required.
All answers shownChinese–English terminology
Diagrams, explanations and answers are presented in reading order. No playback or response is required.

For the 11m simply supported 610×229×140 UB S355, assumed Class 1, find support reactions and draw annotated SFD/BMD, then check LTB inBC andCD using accurateu andv. Design loads:100kN at B3.5 m,200kN atC7.5 m, and full-span 1.4kNm UDL including beam self-weight. Lateral restraints atA/B/C/D.

Original source: Pastpaper/23ENGTY004.pdf — p. 6.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

Vertical bending can trigger sideways motion

A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.

The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.
The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.

Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.

λ=LE/ry,Mb=pbSx  (Class 1/2),mLTMmax≤Mb\lambda=L_E/r_y,\qquad M_b=p_bS_x\;\text{(Class 1/2)},\qquad m_{LT}M_{max}\le M_b

LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.

Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.

Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.

Change the ruler, keep the quantity

A section table uses centimetres, but the strength calculation uses millimetres. The numbers must describe the same section.

Length1 factorArea2 factors3 factorsEach centimetre becomes ten millimetres.
In the diagram, the length, square and cube contain one, two and three length factors. Each factor changes when the ruler changes.

Prediction, then explanation. Would every property increase by ten? No. The exponent determines how many factors of ten are needed.

First identify the physical quantity. Next convert each length factor. Keep force and length conversions separate when converting a moment.

1 cmn=10n mmn,1 kN m=106 N mm1\,\mathrm{cm}^n=10^n\,\mathrm{mm}^n,\qquad 1\,\mathrm{kN\,m}=10^6\,\mathrm{N\,mm}

Here n is the length exponent: 2 for area, 3 for section modulus and 4 for second moment of area.

Scope. Changing units changes neither the load nor the section. A conversion factor cannot repair a formula for the wrong physical quantity.

Check and takeaway. Illustration: 2 cm4=20,000 mm42\,\mathrm{cm}^4=20{,}000\,\mathrm{mm}^4. The fourth power belongs to the unit, not the number 2.

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Apply the reasoning to this section’s data and conditions

Lookup: Data File pp.9–10, exact 610×229×140 UB row.

Dimensions on p.9; properties on p.10.

D is overall depth.

d is the clear web depth between root fillets, not the nominal designation.

PropertyLookup value / conversion
DimensionsD617.2, web t 13.1, flange T22.1, root r 12.7, clear d 547.6, all mm
Local ratiosbT=5.21;dt=41.8
Major-axis propertiesIx=111800cm4=1.118×109mm4; Zx=3622cm3; Sx=4142cm3
LTB propertiesry=5.03cm=50.3mm; u=0.875; torsional index x=30.6

Why this method applies

Moment shape matters within one segment

Represent a nonuniform moment distribution in the applicable member-buckling equation.

The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.
The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.

Prediction, then explanation. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Evaluate moments from the true whole-beam analysis at the required positions. Apply the exact table’s weights, signs and lower bound.

mLT is an LTB factor. mx and my belong to the specified flexural checks. They are not interchangeable.

Scope. Some rules use magnitudes; others require signed ordinates. A factor does not reduce the actual moment used in a local section check.

Check and takeaway. Measure quarter points from the segment start, not automatically from the beam’s left support.

A cut reveals the internal actions

Find where the beam moment is largest. A large load arrow alone does not locate that point.

The dashed imaginary cut separates two beam pieces. The opposing arrows represent the shear action between those pieces.
The dashed imaginary cut separates two beam pieces. The opposing arrows represent the shear action between those pieces.

Prediction, then explanation. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Balance the forces on the cut piece to get V. Balance their moments about the cut to get M. Evaluate each load region separately.

V(x)=RA−wx,M(x)=RAx−wx22V(x)=R_A-wx,\qquad M(x)=R_Ax-\frac{wx^2}{2}

x and L use m; w uses kN/m; V uses kN; M uses kN·m. These lines apply before any point load.

Scope. A point load adds a shear jump. A concentrated couple adds a moment jump. Check load points, supports and overhang roots too.

Check and takeaway. A UDL gives a sloping shear line and a curved moment line. A flat moment diagram therefore cannot represent a loaded UDL region.

Balance the isolated beam

Find the two vertical reactions before calculating internal shear or moment.

A / RₐB / RᵦPaL
A and B are vertical supports. The downward load acts at distance a from A. Its distance from B is L − a.

Prediction, then explanation. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Take moments about A. Reaction A has zero lever arm there. Then use vertical force balance to find reaction A.

RBL=Pa,RA+RB=PR_B L=Pa,\qquad R_A+R_B=P

P, RA and RB are forces in kN. L is support spacing and a is load position, both in m.

Scope. These expressions describe one point load on a simply supported beam. Add other loads through equilibrium; keep their actual positions.

Check and takeaway. Illustration: P = 60 kN, L = 6 m and a = 2 m give RB = 20 kN and RA = 40 kN.

Apply the reasoning to this section’s data and conditions

Use global equilibrium for the complete 11m beam.

Then determine the critical section from shear changes and evaluate the BMD over each specified lateral segment.

The full UDL creates curvature even between the point loads; retain it when computing quarter-point moment factors.

(a) Support reactions —3 printed marks

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why reactions balance the loads

Think of a seesaw that must neither fall nor turn.

Why reactions balance the loads — Think of a seesaw that must neither fall nor turn.

Sketch, not to scale; use the original dimensions.

  1. Upward and downward forces must balance.
  2. Take moments about a support to eliminate its reaction.
  3. Use perpendicular distance from the point to the force line.

Remember: A lateral restraint is not automatically a vertical support.

Related concept and full method

UDL resultant: 1.4×11=15.4kNActs at x=5.5m. ΣMA=011RD=100×3.5+200×7.5+15.4×5.5=350+1,500+84.7=1,934.7kN·mRD=1,934.711=175.881818kNRA=100+200+15.4−175.881818=139.518182kNCheck: RA+RD=315.4kN

Mechanism detailsBalance reactions and moments1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. This demonstrator is a simply supported 6 m beam with a 60 kN point load.

    It is not the page’s original loading diagram.

  2. .

    Moving the load towards B increases .

  3. .

    The two upward reactions must sum to P.

  4. With the load at midspan, .

    End couples, UDLs and overhangs require their own equilibrium terms.

(b) Annotated shear and bending diagrams —4 printed marks

Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Apply the reasoning to this section’s data and conditions

x starts at A and is measured in m. Define ⟨x−a⟩=max(x−a,0). M(x)=139.518182x−0.7x2−100⟨x−3.5⟩−200⟨x−7.5⟩kN·mSegment AB: V=139.518182−1.4xSegment BC: V=39.518182−1.4xSegment CD: V=−160.481818−1.4x
PositionShear just before/after (kN)Moment (kN·m)
A0/+139.5181820
B+134.618182/+34.618182479.738636
C+29.018182/−170.981818607.011364
D−175.881818/00
M(B)=139.518182×3.5−0.7×3.52=479.738636kN·mM(C)=139.518182×7.5−0.7×7.52−100×4=607.011364kN·mShear is positive throughout AB/BC and negative throughout CD, so maximum moment occurs at C, where the 200kN load changes the sign of shear. Shear magnitude is greatest beside D: |V|max=175.881818kN.
Calculated shear and bending diagrams with labelled support/load ordinates; positive values upward. All values are repeated in the working.

Teaching diagrams drawn from the calculation, not original source images.

Labels identify calculated diagrams, positive ordinates upwards, shear force and bending moment.

Positions are in m, V is measured in kN, M is measured in kN·m; A, B, C and D correspond to the original beam positions.

All values are also listed in the solution steps.Open full-size image.

Mechanism detailsBuild the shear and moment diagrams1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For the illustrative 60 kN point load on a 6 m simply supported beam, balance the reactions before making a cut.
  2. and before the point load.

    Moment grows linearly.

  3. Shear jumps down by P.

    To its right, and .

  4. For this case, moment is continuous and returns to zero at B.

    A concentrated applied couple instead creates a moment jump.

(c) BC segment LTB —13 printed marks

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Move between two known values

The required slenderness lies between two table rows. Estimate the strength on the straight segment between those rows.

xy(70, 200)(74, 192)(80, 180)70748040% of input interval → 40% of output change
The marked position lies partway along the horizontal interval. Use the same fraction of the vertical change.

Prediction, then explanation. If the second strength is lower, moving toward that row must reduce the interpolated strength.

Subtract the lower input to find distance travelled. Divide by the input interval. Multiply that fraction by the output change.

f=x−x0x1−x0,y=y0+f(y1−y0)f=\frac{x-x_0}{x_1-x_0},\qquad y=y_0+f(y_1-y_0)

x is the required input. The two known pairs are (x₀, y₀) and (x₁, y₁). f has no unit.

Scope. Use one table, curve and strength column. This interpolation does not permit extrapolation or inventing an intermediate steel section.

Check and takeaway. Illustration: between strengths 200 and 180, a fraction of 0.4 gives 192 N/mm². The result lies between both endpoints.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A beam can escape sideways

The compressed flange can move sideways while the section twists.

A beam can escape sideways — The compressed flange can move sideways while the section twists.

Sketch, not to scale; use the original dimensions.

  1. Divide the beam at effective lateral restraints.
  2. Use each segment’s effective length to obtain its buckling resistance.
  3. Compare that resistance with the segment’s equivalent moment demand.

Remember: A section bending check alone does not check lateral-torsional buckling.

Related concept and full method

S355, flange T=22.1mm, giving py=345Nmm2. ε=275345=0.892805Flange: bT=5.21<9ε=8.035248Web in bending: dt=41.8<80ε=71.424431Both are Class 1, therefore βW=1; plastic bending resistance is permitted.dt=41.8<70ε=62.496377No separate shear-buckling calculation is needed under the course limit.

Flange thickness 22.1mm means that, despite the S355 grade name, use py=345Nmm2.

In the model above, BC’s effective length is 4,000mm.

The quarter-point calculation is shown explicitly below:

In the interval x=4.5: M=139.518182×4.5−0.7×4.52−100×1In the interval x=5.5: M=139.518182×5.5−0.7×5.52−100×2In the interval x=6.5: M=139.518182×6.5−0.7×6.52−100×3

Local quarter positions are 4.5,5.5,6.5m measured fromA.

Use the full beam M(x) evaluated there; segment distance and global x are different quantities.

M2=M(4.5)=513.656818kN·mM3=M(5.5)=546.175000kN·mM4=M(6.5)=577.293182kN·mFor this segment, Mmax=607.011364kN·m. mLT=0.2+0.15|M2|+0.5|M3|+0.15|M4|Mmax=0.919476>0.44Equivalent demand 558.132273kN·m.

Normal-load effective length is the given segment length.

All quantities in λ and λᴸᵀ are dimensionless.

This Class 1 section has βW=1.

λ=LEry=400050.3=79.522863v=[1+0.05(λx)2]−14=[1+0.05(79.52286330.6)2]−14=0.929847λLT=uvλβW=0.875×0.929847×79.522863×1=64.701095

Table 8.3a, Data File p.5, pᵧ345 column:

60 gives 251,65 gives 234Nmm2. Interpolation fraction: 64.701095−6065−60=0.940219pb=251+0.940219×(234−251)=235.016276Nmm2Mb=pbSx1,000=235.016276×41421,000=973.437414kN·mEquivalent uniform moment demand: mLTMmax=558.132273kN·mUtilisation: 558.132273973.437414=0.573362Passes.

Mechanism detailsA beam bends sideways and twists4 concepts · 7 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For the illustrated sagging beam the top flange is compressed.
  2. The unrestrained compression flange can move sideways while the complete cross-section twists.
  3. Only effective restraints divide the member into unbraced segments.

    They do not automatically add vertical supports.

  4. Use the segment effective length, section properties and matching moment factor.

    This is an exaggerated mode shape, not a calculated displacement.

(d) CD segment LTB —10 printed marks

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Use the same mechanism: Move between two known values. If the second strength is lower, moving toward that row must reduce the interpolated strength.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why the shape of the moment diagram matters

The same peak moment is more demanding when a long region stays near that peak.

Why the shape of the moment diagram matters — The same peak moment is more demanding when a long region stays near that peak.

Sketch, not to scale; use the original dimensions.

  1. Use the diagram of this unrestrained segment.
  2. Choose the applicable course sketch or quarter-point rule.
  3. Apply its factor to the demand, following the stated check.

Remember: Column flexural-buckling factors and LTB factors are not interchangeable.

Related concept and full method

CD is 3.5m long.

Its UDL means the BMD is slightly curved, so do not replace the full calculation by an exact triangularβ0 case.

At all three quarter positions, subtract both 100 and 200kN point-load moment contributions.

M(x)=139.518182x−0.7x2−100(x−3.5)−200(x−7.5)Substitute respectively x=8.375, 9.25, 10.125m.

Local quarter positions are 8.375,9.25,10.125m measured fromA.

Use the full beam M(x) evaluated there; segment distance and global x are different quantities.

M2=M(8.375)=456.866335kN·mM3=M(9.25)=305.649432kN·mM4=M(10.125)=153.360653kN·mFor this segment, Mmax=607.011364kN·m. mLT=0.2+0.15|M2|+0.5|M3|+0.15|M4|Mmax=0.602560>0.44Equivalent demand 365.761037kN·m.

Normal-load effective length is the given segment length.

All quantities in λ and λᴸᵀ are dimensionless.

This Class 1 section has βW=1.

λ=LEry=350050.3=69.582505v=[1+0.05(λx)2]−14=[1+0.05(69.58250530.6)2]−14=0.944133λLT=uvλβW=0.875×0.944133×69.582505×1=57.483259

Table 8.3a, Data File p.5, pᵧ345 column:

55 gives 268,60 gives 251Nmm2. Interpolation fraction: 57.483259−5560−55=0.496652pb=268+0.496652×(251−268)=259.556920Nmm2Mb=pbSx1,000=259.556920×41421,000=1075.084763kN·mEquivalent uniform moment demand: mLTMmax=365.761037kN·mUtilisation: 365.7610371075.084763=0.340216Passes.

Both requested segments pass under the stated restraint model.

The paper does not ask forAB buckling in this question.

Do not label the whole beam fully checked merely becauseBC/CD pass.

Mechanism detailsA beam bends sideways and twists4 concepts · 5 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For the illustrated sagging beam the top flange is compressed.
  2. The unrestrained compression flange can move sideways while the complete cross-section twists.
  3. Only effective restraints divide the member into unbraced segments.

    They do not automatically add vertical supports.

  4. Use the segment effective length, section properties and matching moment factor.

    This is an exaggerated mode shape, not a calculated displacement.

Result and concise exam wording

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Apply the reasoning to this section’s data and conditions

RA139.518182,RD175.881818 kN.

MB479.738636,MC607.011364 kNm; maximum shear 175.881818kN. py 345.

BC:LE4 m,mLT0.919476,demand 558.132273,λLT64.701095,pb 235.016276,Mb 973.437414 kNm → passes.

CD:LE3.5 m,mLT0.602560,demand 365.761037,λLT57.483259,pb 259.556920,Mb 1075.084763 kNm → passes.

Retain UDL curvature and the stated normal-load/LE assumption.

Misconceptions and checks

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Apply the reasoning to this section’s data and conditions

  • Do not factor 1.4kNm again.
  • Do not make B/C vertical supports.
  • Use 345Nmm2 forT22.1 mm.
  • Use 4m and 3.5m segment lengths, not the full 11m in both checks.
  • Quarter positions must be local to the chosen segment.

How the method transfers to a new variant

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Use the same mechanism: Move between two known values. If the second strength is lower, moving toward that row must reduce the interpolated strength.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

  1. Solve full-beam reactions including the UDL resultant.
  2. Write piecewise shear/moment equations.
  3. Use shear signs to locate the actual maximum.
  4. For each requested segment, evaluate its own quarter moments and factor.
  5. Read exact section properties and thickness-dependent strength, then calculate u/v and interpolatepb.
  6. Report each segment result and scope.

Prediction with explained answer

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Invented variant: replace the 1.4kNm design UDL by zero, keeping both point loads.

Can you keep the sameBC/CD moment factors?

Answer and reasoning

No. Reactions and allBMD ordinates change, and the segment diagrams become straight between point loads.

Recompute both end moments and use the applicable straight-line moment factor.

The section properties and the stated restraint lengths remain unchanged.