2024 BQ2(b): four-sided weld on a channel web
Determine the required fillet-weld leg for the S355 plate welded on four sides to a parallel-flange-channel web, using Class 42 electrode. Rectangle wide by high. Characteristic dead and imposed act on the right edge line.
Original source: Pastpaper/23ENGTY004.pdf — p. 4.
A given value comes from the question or diagram.
A lookup value comes from the named table.
A calculated value follows from the working.
Each assumption is stated where the calculation needs it.
Known information, diagram labels and unknowns
Treat a weld group as lines
An eccentric force creates direct line force and torsional line force in the same weld group.
Prediction, then explanation. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.
Find the line centroid. Integrate squared distance along the effective lines. Add direct and torsional components at every candidate critical point.
J is line polar inertia in mm³. x and y use mm. With M in kN·mm, q is line force in kN/mm.
Scope. A solid rectangle has area inertia in mm⁴ and is not this weld-line model. Missing weld sides change the centroid and integrals.
Check and takeaway. Compare the largest resultant line force with the selected throat resistance. Keep kN/mm distinct from total force in kN.
The weld resists through its throat
Convert a visible fillet leg into resistance per effective length.
Prediction, then explanation. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.
For the course right-angle equal-leg fillet, take throat as 0.7 times leg. Multiply throat area per unit length by weld strength.
s and a are leg and throat in mm. pw is weld strength in N/mm². qcap is resistance in kN/mm.
Scope. Use effective length, the correct steel/electrode strength and permitted leg limits. Full-penetration butt welds use a different model.
Check and takeaway. Illustration: a 6 mm leg at 250 N/mm² gives .
A table value has conditions
Find a design property without mixing a row, column or standard from a different case.
Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.
Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.
Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.
Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.
Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.
Apply the reasoning to this section’s data and conditions
| Input | Origin |
|---|---|
| Loads | Given dead and live . Apply the course ULS combination once. |
| Geometry | GivenB250,H200 mm; symmetry gives corner coordinates/. |
| Given formulas | The formula on the complete original exam page is and ; in that source expression, , denote full rectangle width and height respectively. The website working uses , to avoid confusion with corner coordinates, writing and . These are weld-line inertias, in . The two notations are equivalent after matching their definitions. |
| Weld strength | S355/Class 42 gives ; equal-leg weld throat . |
| Absent detail | Plate and channel-web thicknesses are not given; exposed-edge maximum leg requires their actual values. |
Why this method applies
Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.
Add force components at each bolt
An in-plane load acts away from the bolt-group centre. Find the largest resultant bolt force.
Prediction, then explanation. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.
Locate the bolt-group centre and coordinates. Add horizontal components together and vertical components together before finding each resultant.
e, xi and yi use mm; J uses mm². With M in kN·mm, each moment-force component is in kN.
Scope. These expressions use the stated elastic, equal-bolt in-plane model. Out-of-plane tension and prying require another model.
Check and takeaway. Do not add force magnitudes before resolving directions. Two perpendicular forces of 3 and 4 kN give 5 kN, not 7 kN.
A force couple carries moment
Separate the force couple used to carry moment from the force used to carry web shear.
Prediction, then explanation. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.
Moment is force multiplied by perpendicular separation. Divide the required moment by the specified separation to obtain each couple force.
M is moment in kN·mm; z is the specified force-line separation in mm; F is force in kN.
Scope. Use the lever arm defined by the source model. Do not silently replace it with overall section depth or another geometric distance.
Check and takeaway. Check flange welds for the couple forces and web welds for the stated shear model. Both force paths need a satisfactory detail.
Apply the reasoning to this section’s data and conditions
Separate the direct vertical line force from the moment-induced tangential force.
The critical corner is the side where the torsional vertical component adds to direct shear.
Use the given line-inertia formulas with full rectangle dimensions, then resolve components before selecting a weld leg.
Complete 13-mark solution: load, line inertia, corner resultant and size
Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.
Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.
Keep load categories separate
A floor carries permanent material and changing occupancy loads. Find the design load for the stated check.
Prediction, then explanation. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.
First convert mass to weight where required. Next collect G and Q in compatible units. Apply the combination specified by the course problem.
G is characteristic dead load; Q is characteristic imposed load. Wu is the design load for this course gravity combination.
Scope. This combination is not universal. Use the specified service load for deflection and the stated factors for other standards or cases.
Check and takeaway. Illustration: G = 10 kN and Q = 5 kN give 22 kN. Factoring their sum by one guessed factor loses the distinction.
Apply the reasoning to this section’s data and conditions
Physical interpretation: Only the weld lines resist as weld
Imagine a wire rectangle: its empty middle is not more wire.
Sketch, not to scale; use the original dimensions.
- Count only the weld runs actually shown.
- Use their total length and line second moments.
- Combine direct and torsional forces at the critical location.
Remember: Line second moments have units ; plate-area moments use .
Physical interpretation: Add arrows before taking the magnitude
Walking east and walking north do not point in the same direction.
Sketch, not to scale; use the original dimensions.
- Choose signed horizontal and vertical directions.
- Add contributions along each direction separately.
- For perpendicular components, use the right-triangle resultant.
Remember: Check the corner where direct and torsional components reinforce each other.
Physical interpretation: Why the weld throat is smaller than its leg
The shortest cut through the weld is thinner than the outside leg.
Sketch, not to scale; use the original dimensions.
- For the stated equal-leg 90° fillet, throat is approximately 0.7 × leg.
- Multiply throat area by the matching weld design strength.
- For force per length, use a one-millimetre weld strip.
Remember: Choose strength from both the steel grade and electrode class.
For the continuous closed-perimeter course model, use the rectangle’s full effective line.
Separate terminated runs would require their actual end deductions and revised geometry.
The question’s provided inertia formulas assume this continuous rectangle.
Both stresses are now expressed as force per effective weld length, so vector combination is dimensionally valid.
The opposite side subtracts the torsional vertical component and does not govern.
meets every minimum-leg value listed in the source table, whose largest minimum is .
However the thinner exposed edge must allow that leg: under the source rule, requires .
Neither thickness is supplied.
Therefore, that maximum-size applicability remains unverified.
Mechanism detailsA weld group is a set of lines
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
Use line lengths for centroid weighting.
Line second moments have units .
Add the parallel-axis terms.
Direct force per length is .
The eccentric moment adds tangential flow proportional to distance from the centroid.
- Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.
Result and concise exam wording
Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.
Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.
Apply the reasoning to this section’s data and conditions
, , , .
, , .
Governing , , resultant .
; trial for strength ,.
Maximum weld leg at the edge depends on unprovided thickness information, so fabrication details cannot be confirmed unconditionally.
Misconceptions and checks
Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.
Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.
Apply the reasoning to this section’s data and conditions
- Do not use as the centroid eccentricity.
- Do not halve : there is one loaded group.
- Use line inertia, not plate-area inertia.
- Do not ignore the maximum permitted edge weld size.
How the method transfers to a new variant
Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.
Use the same mechanism: Add force components at each bolt. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.
Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.
Apply the reasoning to this section’s data and conditions
- Locate the load line relative to the weld centroid.
- Factor characteristic loads and computePe.
- Compute line length and both line inertias.
- Resolve the corner torsional components and add direct shear with signs.
- Convert resultant to leg and check the actual detail limits.
Prediction with explained answer
Use the same mechanism: Keep load categories separate. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.
Apply the reasoning to this section’s data and conditions
Prediction and explained answer.
Invented variant: both characteristic loads increase proportionally.
Does the strength trial pass?
Answer and reasoning
The resultant increases to , above .
The trial fails strength even though the original utilisation was below .
Geometry/materials unchanged means resistance does not scale with load.
Mechanism detailsA weld group is a set of lines
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
Use line lengths for centroid weighting.
Line second moments have units .
Add the parallel-axis terms.
Direct force per length is .
The eccentric moment adds tangential flow proportional to distance from the centroid.
- Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.