STEELWORK / CON4334
Worked examples

Beam example 2: trace a library-floor load into beam B3

Diagrams, explanations and answers are presented in reading order. No playback or response is required.

← Read this lecture example beside its chapter concepts

All answers shownChinese–English terminology
Diagrams, explanations and answers are presented in reading order. No playback or response is required.

Design the fully restrained supporting beam B3 in the library floor plan. Characteristic dead and imposed floor loads are 6 and 4kNm2; the dead load includes the self-weight allowances used by the example. Use S355 and the lecturer’s simply supported member model.

Original source: LectureNotes/Ch 3_Beam.pdf — p. 22, p. 23, p. 24, p. 25, p. 26.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

A safe beam can still sag too far

Check whether the beam displacement exceeds the permitted service limit.

The straight beam marks the unloaded position. The curved line and vertical arrow show downward displacement, exaggerated for explanation.
The straight beam marks the unloaded position. The curved line and vertical arrow show downward displacement, exaggerated for explanation.

Prediction, then explanation. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.

Load bends each beam segment. The curvature accumulates along the span. Material stiffness E and geometric stiffness I resist that deformation.

δmid=5wL4384EI\delta_{mid}=\frac{5wL^4}{384EI}

Use w in N/mm, L in mm, E in N/mm² and I in mm⁴. The resulting midspan deflection is in mm.

Scope. The formula assumes a prismatic, simply supported, linear-elastic beam with full-span UDL. Use the stated service load and deflection limit.

Check and takeaway. A higher yield grade does not automatically increase E. Passing a strength check therefore does not prove acceptable deflection.

Follow one strip of floor

An area load must become a beam load before beam reactions can be calculated.

The highlighted tributary strip supplies one beam. The right-hand labels show area load multiplied by width becoming line load.
The highlighted tributary strip supplies one beam. The right-hand labels show area load multiplied by width becoming line load.

Prediction, then explanation. At fixed area load, twice the tributary width gives twice the line load. An end reaction remains a concentrated force.

Consider one metre along the beam. The associated floor area is b square metres. Multiply area load by that width.

w=qbw=qb

q is area load in kN/m²; b is tributary width in m; w is line load in kN/m.

Scope. Determine b from slab spanning and supports. Add beam self-weight separately. A secondary-beam reaction is not automatically a UDL.

Check and takeaway. Illustration: 3 kN/m2×2 m=6 kN/m3\,\mathrm{kN/m^2}\times2\,\mathrm{m}=6\,\mathrm{kN/m}. The width cancels one length unit.

Apply the reasoning to this section’s data and conditions

FeatureMeaning for loading
Slab span marks crossing the B1 linesSlab load reaches the parallel B1 beams over a 1.25m tributary width.
B1 above and below each interior B2Each B2 loading point receives two B1 end reactions.
B2 on both sides of the interior B3B3 receives two B2 end reactions at its centre.
B3 also directly borders slab stripsInterior B3 carries its own 1.25m tributary slab strip, represented as a UDL.
Given and assumed

All self-weight is already allowed for in the supplied dead intensity.

B3 fully restrained; lecturer assumes brittle finishes for serviceability.

Why this method applies

Balance the isolated beam

Find the two vertical reactions before calculating internal shear or moment.

A / RₐB / RᵦPaL
A and B are vertical supports. The downward load acts at distance a from A. Its distance from B is L − a.

Prediction, then explanation. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Take moments about A. Reaction A has zero lever arm there. Then use vertical force balance to find reaction A.

RBL=Pa,RA+RB=PR_B L=Pa,\qquad R_A+R_B=P

P, RA and RB are forces in kN. L is support spacing and a is load position, both in m.

Scope. These expressions describe one point load on a simply supported beam. Add other loads through equilibrium; keep their actual positions.

Check and takeaway. Illustration: P = 60 kN, L = 6 m and a = 2 m give RB = 20 kN and RA = 40 kN.

Apply the reasoning to this section’s data and conditions

Work upstream before downstream: slab → B1 → B2 → B3.

A supporting beam receives a point load equal to the end reaction of the supported beam, not that beam’s entire load.

Keep dead and imposed reactions separate until the B3 loading is established.

Do not treat the 5m horizontal bay width as the B3 span.

1. Slab to B1

Use the same mechanism: Follow one strip of floor. At fixed area load, twice the tributary width gives twice the line load. An end reaction remains a concentrated force.

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Apply the reasoning to this section’s data and conditions

B1 span =3m; tributary width =1.25m. gB1=6kNm2×1.25m=7.5kNmqB1=4×1.25=5kNmDead-load reaction at each end: 7.5×32=11.25kNImposed-load reaction at each end: 5×32=7.5kN

The division by two comes from a uniformly loaded simply supported span.

These are characteristic reactions, before the ultimate factors.

Mechanism detailsFollow the floor load in 3D2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The floor carries pressure in .

    The highlighted strip belongs to one secondary beam.

  2. Multiply pressure by tributary width: .

    The illustration uses .

  3. A primary beam receives the secondary beam reaction at their connection, not a new full-span UDL.
  4. Trace reactions down to columns and foundations.

    Count each loaded area once.

2. B1 reactions to B2

Use the same mechanism: Follow one strip of floor. At fixed area load, twice the tributary width gives twice the line load. An end reaction remains a concentrated force.

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Apply the reasoning to this section’s data and conditions

Each internal B1 line has two spans joining B2: Gpoint,B2=2×11.25=22.5kNQpoint,B2=2×7.5=15kNIn the interval 5m B2 span has three equally spaced point loads at 1.25,2.5,3.75m. B2 dead-load reaction at each end: 3×22.52=33.75kNB2 imposed-load reaction at each end: 3×152=22.5kN

There are three internal point loads, not four: four slab strips are bounded by three interior B1 lines and the two B3 boundaries.

Symmetry of the three loads gives half the total at each B2 end.

Loads arriving directly at column-supported beam ends do not add span bending.

Mechanism detailsFollow the floor load in 3D2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The floor carries pressure in .

    The highlighted strip belongs to one secondary beam.

  2. Multiply pressure by tributary width: .

    The illustration uses .

  3. A primary beam receives the secondary beam reaction at their connection, not a new full-span UDL.
  4. Trace reactions down to columns and foundations.

    Count each loaded area once.

3. Assemble B3 point load and direct slab UDL

Use the same mechanism: Follow one strip of floor. At fixed area load, twice the tributary width gives twice the line load. An end reaction remains a concentrated force.

Keep load categories separate

A floor carries permanent material and changing occupancy loads. Find the design load for the stated check.

The two boxes show G and Q with their separate factors. The plus sign joins their factored values.
The two boxes show G and Q with their separate factors. The plus sign joins their factored values.

Prediction, then explanation. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

First convert mass to weight where required. Next collect G and Q in compatible units. Apply the combination specified by the course problem.

Wu=1.4G+1.6QW_u=1.4G+1.6Q

G is characteristic dead load; Q is characteristic imposed load. Wu is the design load for this course gravity combination.

Scope. This combination is not universal. Use the specified service load for deflection and the stated factors for other standards or cases.

Check and takeaway. Illustration: G = 10 kN and Q = 5 kN give 22 kN. Factoring their sum by one guessed factor loses the distinction.

Apply the reasoning to this section’s data and conditions

Physical interpretation: How a floor load reaches a beam

Each beam collects the load from its own strip of floor.

How a floor load reaches a beam — Each beam collects the load from its own strip of floor.

Sketch, not to scale; use the original dimensions.

  1. Find the tributary width from the actual plan.
  2. Area load × tributary width gives load per beam length.
  3. A supporting beam receives the other beam’s end reaction.

Remember: A reaction becomes a point load, not automatically a UDL.

Related concept and full method

Midspan dead point load: 2×33.75=67.5kNMidspan imposed point load: 2×22.5=45kNDirect dead UDL: 6×1.25=7.5kNmDirect imposed UDL: 4×1.25=5kNmUltimate point load: P=1.4×67.5+1.6×45=94.5+72=166.5kNUltimate UDL: w=1.4×7.5+1.6×5=10.5+8=18.5kNm

The factor of two at the central point represents the B2 on each side of B3.

It does not double B3’s 6m span or its 1.25m tributary strip.

Mechanism detailsFollow the floor load in 3D2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The floor carries pressure in .

    The highlighted strip belongs to one secondary beam.

  2. Multiply pressure by tributary width: .

    The illustration uses .

  3. A primary beam receives the secondary beam reaction at their connection, not a new full-span UDL.
  4. Trace reactions down to columns and foundations.

    Count each loaded area once.

4. Reactions, shear and moment of B3

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

A cut reveals the internal actions

Find where the beam moment is largest. A large load arrow alone does not locate that point.

The dashed imaginary cut separates two beam pieces. The opposing arrows represent the shear action between those pieces.
The dashed imaginary cut separates two beam pieces. The opposing arrows represent the shear action between those pieces.

Prediction, then explanation. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Balance the forces on the cut piece to get V. Balance their moments about the cut to get M. Evaluate each load region separately.

V(x)=RA−wx,M(x)=RAx−wx22V(x)=R_A-wx,\qquad M(x)=R_Ax-\frac{wx^2}{2}

x and L use m; w uses kN/m; V uses kN; M uses kN·m. These lines apply before any point load.

Scope. A point load adds a shear jump. A concentrated couple adds a moment jump. Check load points, supports and overhang roots too.

Check and takeaway. A UDL gives a sloping shear line and a curved moment line. A flat moment diagram therefore cannot represent a loaded UDL region.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why reactions balance the loads

Think of a seesaw that must neither fall nor turn.

Why reactions balance the loads — Think of a seesaw that must neither fall nor turn.

Sketch, not to scale; use the original dimensions.

  1. Upward and downward forces must balance.
  2. Take moments about a support to eliminate its reaction.
  3. Use perpendicular distance from the point to the force line.

Remember: A lateral restraint is not automatically a vertical support.

Related concept and full method

Characteristic dead-load reaction: 67.5+7.5×62=56.25kNCharacteristic imposed-load reaction: 45+5×62=37.5kNUltimate reaction: 1.4×56.25+1.6×37.5=138.75kNDirect check: 166.5+18.5×62=138.75kNShear immediately left of midspan: 138.75−18.5×3=83.25kNImmediately right of midspan: 83.25−166.5=−83.25kNMmax=166.5×64+18.5×628=249.75+83.25=333kN·mMaximum shear occurs at the supports: |V|max=138.75kN.

Mechanism detailsBalance reactions and moments2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. This demonstrator is a simply supported 6 m beam with a 60 kN point load.

    It is not the page’s original loading diagram.

  2. .

    Moving the load towards B increases .

  3. .

    The two upward reactions must sum to P.

  4. With the load at midspan, .

    End couples, UDLs and overhangs require their own equilibrium terms.

5. Select 457×152×52 UB

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Use the property for the physical question

A section table contains several numbers. Choose the property that matches the calculation and bending axis.

Read the three labels beside the I-section: I describes geometric stiffness, Z elastic section modulus and S plastic section modulus.
Read the three labels beside the I-section: I describes geometric stiffness, Z elastic section modulus and S plastic section modulus.

Prediction, then explanation. Moving equal area away from an axis increases I about that axis. It does not increase total area.

Each small area contributes its area multiplied by squared distance. Sum those contributions to obtain I.

I=∫y2 dA,r=I/AI=\int y^2\,dA,\qquad r=\sqrt{I/A}

I is second moment of area in mm⁴. y is distance from the chosen axis in mm. A is area in mm². r is radius of gyration in mm.

Scope. Z is elastic section modulus; S is plastic section modulus in this course. Neither is interchangeable with I.

Check and takeaway. A nominal section designation is a row identifier. Use the actual dimensions and units in that exact row.

Internal tension and compression resist moment

Find which section resistance applies before comparing it with the moment demand.

In sagging bending, the upper region compresses and the lower region stretches. Together their forces form a resisting couple.
In sagging bending, the upper region compresses and the lower region stretches. Together their forces form a resisting couple.

Prediction, then explanation. A larger appropriate section modulus raises resistance at fixed strength. Local plate buckling can restrict the usable modulus.

Classify the section first. At low shear, use the elastic expression for Class 3 or the prescribed capped plastic expression for Classes 1 and 2.

Mc=min⁡(pyS,1.2pyZ)for Class 1/2 at low shearM_c=\min(p_yS,1.2p_yZ)\quad\text{for Class 1/2 at low shear}

py uses N/mm². S is plastic modulus and Z is elastic modulus, both in mm³. Mc then uses N·mm.

Scope. This is section resistance, not whole-member LTB resistance. High shear and Class 4 require their appropriate treatment.

Check and takeaway. Selecting the larger of the two capped terms defeats the cap. Use their minimum.

Apply the reasoning to this section’s data and conditions

Trial py=355Nmm2. Srequired=333×106355=938,028.17mm3=938.028cm3Selected Sx=1,096cm3>938.028.

Data File p.9 row 457×152×52 gives D=449.8, t=7.6, T=10.9, r=10.2, d=407.6mm, bT=6.99 and dt=53.6.

Page 10, the same designation, gives Ix=21,370cm4, Zx=950cm3, Sx=1,096cm3.

T=10.9≤16 confirms pᵧ=355.

No interpolation is used for section properties: read the exact row.

Mechanism detailsRead a table without losing the keys3 concepts · 12 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Name the required property: material strength, section property, buckling strength or a moment factor.
  2. Keep section size, steel grade, thickness band, curve and axis as separate lookup keys.
  3. , and require different conversion powers.

    Do not use adjacent columns interchangeably.

  4. Use bracketing rows within the same valid column.

    The original page remains the source of all table values.

6. Classify the trial section

Find which plate buckles first

Before using plastic bending resistance, check whether the flange and web can sustain the required stress distribution.

The short waves are local plate buckling. They differ from sideways movement of the whole member.
The short waves are local plate buckling. They differ from sideways movement of the whole member.

Prediction, then explanation. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Calculate the flange and web ratios separately. Compare each with the limits for its stress condition. The worse class governs.

ε=275/py\varepsilon=\sqrt{275/p_y}

py is the design yield strength in N/mm². ε is a dimensionless scale used in the supplied classification limits.

Scope. Pure bending and uniform compression use different web limits. Class 2 allows plastic resistance but not the Class 1 rotation capability.

Check and takeaway. A Class 1 web and Class 2 flange give a Class 2 section. Do not average the class numbers.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

ε=275355=0.880141bT=6.99<9ε=7.92127The flange is Class 1.dt=53.6<80ε=70.4113The web in bending is Class 1; overall Class 1.dt=53.6<70ε=61.6099No separate web shear-buckling check is needed.

Mechanism detailsWhy thin elements buckle locally2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The flange outstand and web have different widths, thicknesses and edge support conditions.
  2. A thinner plate can wrinkle locally before the complete member loses stability.
  3. Class 1 allows plastic rotation.

    Class 2 reaches plastic resistance.

    Class 3 reaches elastic resistance.

    Class 4 requires effective properties.

  4. Check every relevant compression element with the supplied limits and stress distribution.

    The deformation shown is qualitative.

7. Check shear resistance

The web carries the shear check

Compare the applied shear with the resistance of the prescribed shear area.

At the imaginary cut, opposing arrows resist relative sliding. The rolled-UB calculation below assigns the shear area to the web.
At the imaginary cut, opposing arrows resist relative sliding. The rolled-UB calculation below assigns the shear area to the web.

Prediction, then explanation. At fixed design strength and depth, increasing web thickness increases this shear resistance.

Calculate the prescribed shear area. Multiply by the design shear stress from the course rule. Then compare matching force units.

Av=Dt,Vc=pyAv/3A_v=Dt,\qquad V_c=p_yA_v/\sqrt{3}

D is overall depth; t is web thickness, in mm. Av uses mm². py uses N/mm², giving Vc in N.

Scope. Apply this area definition to the stated rolled section. Check web slenderness separately. The factor 0.6 is the low-shear threshold, not this resistance coefficient.

Check and takeaway. A shear pass alone does not prove bending, deflection or local support-web adequacy.

Apply the reasoning to this section’s data and conditions

Av=tD=7.6×449.8=3,418.48mm2Vc=355×3,418.483×1,000=700.649kN138.75<700.649: shear passes.

Mechanism detailsSee shear in the web1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Internal shear keeps the two sides of the cut in vertical equilibrium.
  2. For the course’s common I-section case, the web provides the principal shear area.

    Use the specified definition.

  3. A slender web may require a different shear-buckling route before a simple shear-resistance formula is used.
  4. Use where applicable in the course.

    Convert N to kN before comparing with design shear.

8. Check moment resistance

Use the same mechanism: Internal tension and compression resist moment. A larger appropriate section modulus raises resistance at fixed strength. Local plate buckling can restrict the usable modulus.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why one flange squeezes and the other stretches

Bending makes opposite sides of the section do opposite jobs.

Why one flange squeezes and the other stretches — Bending makes opposite sides of the section do opposite jobs.

Sketch, not to scale; use the original dimensions.

  1. Find the moment from the actual loads and supports.
  2. Choose the resistance formula allowed by the section class.
  3. Check whether the coexistent shear changes that formula.

Remember: Use shear at the location being checked, not an unrelated maximum.

Related concept and full method

Shear at the same midspan section =83.25kN. 0.6Vc=420.390kN>83.25is low shear.pySx=355×1,0961,000=389.08kN·m1.2pyZx=1.2×355×9501,000=404.7kN·mMc=389.08kN·m>333kN·mPasses.

The source’s requested B3 design demonstrates shear, moment and deflection.

It does not specify a bearing geometry for a numerical local-web design here.

Do not import the 160mm bearing from Example 1.

Mechanism detailsCompression and tension across a section1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. For sagging, the top flange is in compression and the bottom in tension; hogging reverses this.
  2. Elastic bending stress varies with distance from the neutral axis: .
  3. The section class governs whether elastic, plastic or effective properties may be used.
  4. Use the shear at the section under examination.

    The largest shear elsewhere is not automatically coexistent.

9. Check B3 serviceability

Use the same mechanism: A safe beam can still sag too far. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.

Apply the reasoning to this section’s data and conditions

Physical interpretation: How much does the beam sag?

Strength asks whether it fails; deflection asks how far it moves.

How much does the beam sag? — Strength asks whether it fails; deflection asks how far it moves.

Sketch, not to scale; use the original dimensions.

  1. Use the serviceability load case specified by the course question.
  2. Choose the expression matching the support and load positions.
  3. Use consistent units for load, length, E and I.

Remember: The largest deflection is not always at midspan.

Related concept and full method

Use imposed load P=45,000N, w=5Nmm, and L=6,000mm. I=21,370×104=213,700,000mm4δP=45,000×6,000348×205,000×213,700,000=4.62239mmδw=5×5×6,0004384×205,000×213,700,000=1.92600mmδ=4.62239+1.92600=6.54839mmL360=6,000360=16.66667mm6.54839<16.66667: passes under the assumed brittle-finish condition.

Mechanism detailsSee stiffness and deflection1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Use the specified SLS load, span and support arrangement.

    The demonstrator has a full-span UDL.

  2. The loaded beam bends.

    The deformation is exaggerated so its shape can be seen.

  3. For a simply supported full-span UDL, .

    Double L with w, E and I unchanged: δ becomes 16 times as large.

  4. The readout uses , and .

    Select the finish/support-specific limit from the original table.

Result and concise exam wording

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Apply the reasoning to this section’s data and conditions

B1 characteristic reactions G/Q=11.25/7.5kN.

B2 has three 22.5/15kN points; end reactions 33.75/22.5kN.

B3 central G/Q=67.5/45kN plus 7.5/5kNm.

Ultimate P=166.5kN, w=18.5kNm, Vmax=138.75kN, Mmax=333kN·m.

Select 457×152×52 UB S355, Class 1: Vc=700.649kN, Mc=389.08kN·m, δ=6.548mm<16.667mm.

The demonstrated checks pass.

Misconceptions and checks

Use the same mechanism: Follow one strip of floor. At fixed area load, twice the tributary width gives twice the line load. An end reaction remains a concentrated force.

Apply the reasoning to this section’s data and conditions

  • Do not make floor pressure a beam UDL without multiplying by tributary width.
  • Do not transfer a supported beam’s entire load to each end.
  • Include B3’s directly supported slab strip once.
  • Do not add self-weight already included by the problem.

How the method transfers to a new variant

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Use the same mechanism: A safe beam can still sag too far. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.

Vertical bending can trigger sideways motion

A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.

The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.
The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.

Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.

λ=LE/ry,Mb=pbSx  (Class 1/2),mLTMmax≤Mb\lambda=L_E/r_y,\qquad M_b=p_bS_x\;\text{(Class 1/2)},\qquad m_{LT}M_{max}\le M_b

LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.

Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.

Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.

Apply the reasoning to this section’s data and conditions

  1. Identify the vertical supports, span, lateral restraints and individual load positions.
  2. Keep dead and imposed loads separate; form the required ultimate and serviceability cases.
  3. Find reactions and the maximum shear/moment by equilibrium, with units.
  4. Choose a section-table row, confirm thickness-dependent strength, and classify both flange and web.
  5. Check shear and bending.

    Add segment LTB where restraint is discrete.

  6. Complete the requested web and deflection checks; state the governing result and any missing data.

Prediction with explained answer

Use the same mechanism: A safe beam can still sag too far. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Invented variant: only the characteristic floor imposed pressure rises from 4 to 5kNm2.

Find the revised B3 ultimate P and w, and imposed deflection; retain the original dead loading.

Answer and reasoning

All imposed effects multiply by 54.

B3 imposed point=56.25kN; imposed UDL=6.25kNm.

P=1.4×67.5+1.6×56.25=184.5kN; w=1.4×7.5+1.6×6.25=20.5kNm

M=184.5×64+20.5×368=369kN·m<389.08

Imposed deflection=6.54839×1.25=8.18549mm<16.66667

Maximum shear=184.5+20.5×62=153.75kN<700.649; these checks still pass.

Mechanism detailsFollow the floor load in 3D5 concepts · 7 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The floor carries pressure in .

    The highlighted strip belongs to one secondary beam.

  2. Multiply pressure by tributary width: .

    The illustration uses .

  3. A primary beam receives the secondary beam reaction at their connection, not a new full-span UDL.
  4. Trace reactions down to columns and foundations.

    Count each loaded area once.