Connection example 9: a welded single unequal angle
← Read this lecture example beside its chapter concepts
Check a S355 single angle connected by its long leg under dead plus imposed tension, and design the two side welds with Class 42 electrode.
Original source: LectureNotes/Ch 2_Connection.pdf — p. 42.
A given value comes from the question or diagram.
A lookup value comes from the named table.
A calculated value follows from the working.
Each assumption is stated where the calculation needs it.
Known information, diagram labels and unknowns
The weld resists through its throat
Convert a visible fillet leg into resistance per effective length.
Prediction, then explanation. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.
For the course right-angle equal-leg fillet, take throat as 0.7 times leg. Multiply throat area per unit length by weld strength.
s and a are leg and throat in mm. pw is weld strength in N/mm². qcap is resistance in kN/mm.
Scope. Use effective length, the correct steel/electrode strength and permitted leg limits. Full-penetration butt welds use a different model.
Check and takeaway. Illustration: a 6 mm leg at 250 N/mm² gives .
A table value has conditions
Find a design property without mixing a row, column or standard from a different case.
Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.
Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.
Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.
Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.
Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.
Apply the reasoning to this section’s data and conditions
| Input | Origin |
|---|---|
| Given loads | dead and imposed, task text. |
| Given dimensions | angle; source diagram shows and half-heel widths and centroid height. |
| Lookup centroid | from SideX stated from section table in solution and labelled in diagram. Opposite arm . |
| Lookup strengths | S355 thickness → ; S355/Class 42 →. |
| Design choice | fillet, physical lengths (X), (Y), lecturer solution. |
Why this method applies
Unequal lever arms require unequal forces
Two longitudinal welds must transfer a tensile force through the angle centroid without an unintended moment.
Prediction, then explanation. The weld with the shorter lever arm must carry more force to balance the longer-arm weld’s moment.
Use force balance and moment balance together. Then divide each force by its own line resistance to find required effective length.
P, F₁ and F₂ are forces. z₁ and z₂ are perpendicular distances from the load line. Use consistent length units.
Scope. Equal force shares apply only to the symmetric case. Physical terminated weld length also needs the supplied end deductions.
Check and takeaway. If the two lever arms become equal, the equations return equal forces. That limiting case checks the force distribution.
One connected leg does not load both legs equally
An angle carries tension through only one leg. Determine how much section area the design rule permits.
Prediction, then explanation. Keeping the same gross area does not guarantee the same tension resistance when the connection arrangement changes.
Separate connected and outstanding leg areas. Include the actual holes. Then use the supplied single-angle or double-angle effective-area rule.
Ae is the effective area from the applicable angle rule in mm². py is the relevant design strength in N/mm².
Scope. Do not assume the whole gross area is effective. Symmetry, connected leg and connection type determine which rule applies.
Check and takeaway. The outstanding leg contributes through load transfer; the rule need not either count all of it or discard all of it.
Apply the reasoning to this section’s data and conditions
First check that the angle itself can carry the force: stronger welds cannot cure a weak angle.
With no bolt holes, the gross area is effective, but a single welded connected leg still has the reduction for the unconnected leg.
Then balance the two parallel weld forces about the centroid using their opposite lever arms.
1. Factored force and welded-angle resistance
Use the same mechanism: One connected leg does not load both legs equally. Keeping the same gross area does not guarantee the same tension resistance when the connection arrangement changes.
Keep load categories separate
A floor carries permanent material and changing occupancy loads. Find the design load for the stated check.
Prediction, then explanation. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.
First convert mass to weight where required. Next collect G and Q in compatible units. Apply the combination specified by the course problem.
G is characteristic dead load; Q is characteristic imposed load. Wu is the design load for this course gravity combination.
Scope. This combination is not universal. Use the specified service load for deflection and the stated factors for other standards or cases.
Check and takeaway. Illustration: G = 10 kN and Q = 5 kN give 22 kN. Factoring their sum by one guessed factor loses the distinction.
Apply the reasoning to this section’s data and conditions
Physical interpretation: One connected leg does not load both legs equally
The connected leg receives the pull first.
The other leg receives it through the angle.
Sketch, not to scale; use the original dimensions.
- Identify connected and outstanding legs from the drawing.
- Use the relevant bolted or welded angle rule.
- Keep the lecturer’s area convention consistent.
Remember: Bolted and welded reduction expressions are not the same rule.
The factor comes from the single welded angle rule on Ch 2 p.14.
The bolted value would be a different connection model.
Mechanism detailsWhy a connected angle leg matters
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- Locate the connected leg, outstanding leg and centroid before using the table.
- Only the connected leg directly receives the fastener force.
The outstanding area may not become equally effective at the same section.
This motivates the effective-area rule.
Bolted, welded, single-angle and double-angle details can have different rules.
Preserve the formula attached to the original case.
2. Trial weld and balanced required lengths
Use the same mechanism: Unequal lever arms require unequal forces. The weld with the shorter lever arm must carry more force to balance the longer-arm weld’s moment.
Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.
Apply the reasoning to this section’s data and conditions
Physical interpretation: Why two weld lengths can be unequal
Two side welds must balance the load about its actual line of action.
Sketch, not to scale; use the original dimensions.
- Find the load line and the lever arm to each weld.
- Balance moments as well as the total force.
- Convert each weld’s force into its own required length.
Remember: Equal-looking legs do not justify equal weld forces without equilibrium.
The centroid height is visible in the section but is not the transverse lever arm for sharing these two side-weld forces.
The side-to-side /50.6 dimensions are the relevant ones.
Mechanism detailsBalance two weld forces
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- The angle centroid/load line is generally not halfway between the two weld runs.
.
Both weld runs contribute to the applied force.
.
The run nearer the load line carries more force.
For equal throat resistance per length, the required effective lengths follow the same ratio.
Add detailing allowances afterwards.
3. Final lengths, capacities and source correction
Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.
Use the same mechanism: Unequal lever arms require unequal forces. The weld with the shorter lever arm must carry more force to balance the longer-arm weld’s moment.
Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.
Apply the reasoning to this section’s data and conditions
Physical interpretation: Drawn length and useful length differ
The start and end of a weld are not credited as fully effective in this course model.
Sketch, not to scale; use the original dimensions.
- Find the effective length required by strength.
- Add the specified end allowance to each separate run.
- Round up, then check minimum size, spacing and returns.
Remember: Strength alone does not prove a weld detail is acceptable.
Both effective lengths exceed , and both physical lengths exceed separation.
For the angle edge the maximum leg is , matching the selection.
The minimum-size rule depends on the unknown supporting plate thickness.
Do not assume it from the sketch.
Mechanism detailsFrom fillet leg to effective throat
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- An equal-leg fillet between perpendicular plates has an approximately right-triangular section.
For this geometry, throat .
It is shorter than the leg.
Effective resisting area = .
With here, capacity per length is .
- Use the course end allowances, minimum size and length rules; increasing the geometric length alone does not resolve every detailing check.
Result and concise exam wording
Use the same mechanism: One connected leg does not load both legs equally. Keeping the same gross area does not guarantee the same tension resistance when the connection arrangement changes.
Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.
Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.
Apply the reasoning to this section’s data and conditions
.
Welded single-angle capacity.
Use fillets with .
Required effective X/Y lengths /.
Provide / physical lengths (/ effective), giving / against /.
Angle and weld strength pass; support-thickness detailing is unprovided.
Misconceptions and checks
Use the same mechanism: One connected leg does not load both legs equally. Keeping the same gross area does not guarantee the same tension resistance when the connection arrangement changes.
Apply the reasoning to this section’s data and conditions
- Do not subtract holes from a welded angle with no holes.
- The unconnected leg still needs the reduction.
For the weld, the source writes “Add 12” (add ) is a textual error.
It should be .
- Do not use centroid height in the transverse weld-force split.
How the method transfers to a new variant
Use the same mechanism: Unequal lever arms require unequal forces. The weld with the shorter lever arm must carry more force to balance the longer-arm weld’s moment.
Use the same mechanism: One connected leg does not load both legs equally. Keeping the same gross area does not guarantee the same tension resistance when the connection arrangement changes.
Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.
Apply the reasoning to this section’s data and conditions
- Check angle area and the appropriate welded single-leg resistance.
- Read centroid location from the source/table.
- Select a weld leg permitted by the angle edge.
- Balance side forces, calculate effective lengths, then add to each.
- Verify each rounded side and the detailing conditions.
Prediction with explained answer
Use the same mechanism: One connected leg does not load both legs equally. Keeping the same gross area does not guarantee the same tension resistance when the connection arrangement changes.
Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.
Apply the reasoning to this section’s data and conditions
Prediction and explained answer.
If the imposed load rises to , do the existing / welds still pass?
Answer and reasoning
.
SideX demand; SideY.
Both weld sides fail although angle capacity 223.437 still passes.
Mechanism detailsBalance two weld forces
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- The angle centroid/load line is generally not halfway between the two weld runs.
.
Both weld runs contribute to the applied force.
.
The run nearer the load line carries more force.
For equal throat resistance per length, the required effective lengths follow the same ratio.
Add detailing allowances afterwards.