STEELWORK / CON4334
Worked examples

Connection example 7: calculate a rectangular weld group from first principles

Diagrams, explanations and answers are presented in reading order. No playback or response is required.

← Read this lecture example beside its chapter concepts

All answers shownChinese–English terminology
Diagrams, explanations and answers are presented in reading order. No playback or response is required.

Find the maximum force per unit weld length and select a fillet weld for one side plate carrying 60kN dead plus 90kN imposed load. The weld is on all four sides of a 200mm×300mm rectangle; the force eccentricity from its centre is 300mm. Steel is S355 with Class 42 electrode.

Original source: LectureNotes/Ch 2_Connection.pdf — p. 39, p. 40.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

The weld resists through its throat

Convert a visible fillet leg into resistance per effective length.

The two outer sides are the legs. The shorter perpendicular line through the ideal triangle is the throat.
The two outer sides are the legs. The shorter perpendicular line through the ideal triangle is the throat.

Prediction, then explanation. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

For the course right-angle equal-leg fillet, take throat as 0.7 times leg. Multiply throat area per unit length by weld strength.

a=0.7s,qcap=0.7spw/1000a=0.7s,\qquad q_{cap}=0.7sp_w/1000

s and a are leg and throat in mm. pw is weld strength in N/mm². qcap is resistance in kN/mm.

Scope. Use effective length, the correct steel/electrode strength and permitted leg limits. Full-penetration butt welds use a different model.

Check and takeaway. Illustration: a 6 mm leg at 250 N/mm² gives 0.7(6)(250)/1000=1.05 kN/mm0.7(6)(250)/1000=1.05\,\mathrm{kN/mm}.

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Apply the reasoning to this section’s data and conditions

InputOrigin
Given geometry

b=200mm,h=300mm; four weld sides.

Centre is at half width/height: x=100,y=150mm at a corner.

Given load arme=300mm from group centroid, not from the right edge.
Given materialsS355/Class 42 → lookup pw=250Nmm2, Table 9.2a.
AssumptionUniform fillet size, rigid plate and line-weld elastic distribution, as in Ch 2 pp.35–37.

Why this method applies

Treat a weld group as lines

An eccentric force creates direct line force and torsional line force in the same weld group.

The four perimeter lines represent weld runs. The interior label says No weld here: the enclosed plate area is not weld length.
The four perimeter lines represent weld runs. The interior label says No weld here: the enclosed plate area is not weld length.

Prediction, then explanation. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Find the line centroid. Integrate squared distance along the effective lines. Add direct and torsional components at every candidate critical point.

J=∫r2 dl,qMx=−My/J,qMy=Mx/JJ=\int r^2\,dl,\qquad q_{Mx}=-My/J,\quad q_{My}=Mx/J

J is line polar inertia in mm³. x and y use mm. With M in kN·mm, q is line force in kN/mm.

Scope. A solid rectangle has area inertia in mm⁴ and is not this weld-line model. Missing weld sides change the centroid and integrals.

Check and takeaway. Compare the largest resultant line force with the selected throat resistance. Keep kN/mm distinct from total force in kN.

Add force components at each bolt

An in-plane load acts away from the bolt-group centre. Find the largest resultant bolt force.

The direct-force arrows are parallel. The moment-force arrows run tangentially around the bolt-group centre.
The direct-force arrows are parallel. The moment-force arrows run tangentially around the bolt-group centre.

Prediction, then explanation. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Locate the bolt-group centre and coordinates. Add horizontal components together and vertical components together before finding each resultant.

M=Pe,J=∑(xi2+yi2),FMx=−Myi/J,FMy=Mxi/JM=Pe,\quad J=\sum(x_i^2+y_i^2),\quad F_{Mx}=-My_i/J,\quad F_{My}=Mx_i/J

e, xi and yi use mm; J uses mm². With M in kN·mm, each moment-force component is in kN.

Scope. These expressions use the stated elastic, equal-bolt in-plane model. Out-of-plane tension and prying require another model.

Check and takeaway. Do not add force magnitudes before resolving directions. Two perpendicular forces of 3 and 4 kN give 5 kN, not 7 kN.

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Apply the reasoning to this section’s data and conditions

Separate direct shear PL from torsional force caused by Pe.

Use the weld lines for centroid and inertia.

The plate interior does not carry weld force.

Derive line inertias with the parallel-axis rule.

Then combine the horizontal and vertical force-per-length components at the right-hand corner, where vertical components add.

1. Geometry and factored force

Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Keep load categories separate

A floor carries permanent material and changing occupancy loads. Find the design load for the stated check.

The two boxes show G and Q with their separate factors. The plus sign joins their factored values.
The two boxes show G and Q with their separate factors. The plus sign joins their factored values.

Prediction, then explanation. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

First convert mass to weight where required. Next collect G and Q in compatible units. Apply the combination specified by the course problem.

Wu=1.4G+1.6QW_u=1.4G+1.6Q

G is characteristic dead load; Q is characteristic imposed load. Wu is the design load for this course gravity combination.

Scope. This combination is not universal. Use the specified service load for deflection and the stated factors for other standards or cases.

Check and takeaway. Illustration: G = 10 kN and Q = 5 kN give 22 kN. Factoring their sum by one guessed factor loses the distinction.

Apply the reasoning to this section’s data and conditions

L=2(b+h)=2(200+300)=1,000mmP=1.4×60+1.6×90=84+144=228kNM=Pe=228×300=68,400kN·mmr=1002+1502=32,500=180.278mm

Mechanism detailsA weld group is a set of lines2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
  2. Use line lengths for centroid weighting.

    Line second moments have units .

    Add the parallel-axis terms.

  3. Direct force per length is .

    The eccentric moment adds tangential flow proportional to distance from the centroid.

  4. Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.

2. Derive both line second moments

Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Only the weld lines resist as weld

Imagine a wire rectangle: its empty middle is not more wire.

Only the weld lines resist as weld — Imagine a wire rectangle: its empty middle is not more wire.

Sketch, not to scale; use the original dimensions.

  1. Count only the weld runs actually shown.
  2. Use their total length and line second moments.
  3. Combine direct and torsional forces at the critical location.

Remember: Line second moments have units mm3; plate-area moments use mm4.

Related concept and full method

About the horizontal centroidal x axis: two vertical welds each contribute h312; two horizontal welds each contribute b(h2)2.

About the vertical axis reverse the roles.

Ix=2(300312)+2×200×1502=4,500,000+9,000,000=13,500,000mm3Iy=2(200312)+2×300×1002=1,333,333.333+6,000,000=7,333,333.333mm3Ip=Ix+Iy=20,833,333.333mm3

Why is the unit mm3?

Weld-line length (mm) multiplied by distance squared (mm2) gives that unit.

Do not substitute the second moment of area of a solid rectangular plate, bh312, whose unit is mm4.

Mechanism detailsA weld group is a set of lines1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
  2. Use line lengths for centroid weighting.

    Line second moments have units .

    Add the parallel-axis terms.

  3. Direct force per length is .

    The eccentric moment adds tangential flow proportional to distance from the centroid.

  4. Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.

3. Uniform direct shear per length

Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Apply the reasoning to this section’s data and conditions

qs=PL=228kN1,000mm=0.228kNmm

Mechanism detailsA weld group is a set of lines1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
  2. Use line lengths for centroid weighting.

    Line second moments have units .

    Add the parallel-axis terms.

  3. Direct force per length is .

    The eccentric moment adds tangential flow proportional to distance from the centroid.

  4. Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.

4. Torsional components at the critical corner

Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Apply the reasoning to this section’s data and conditions

qT=MrIp=68,400×180.27820,833,333.333=0.591888kNmmVertical component: MxIp=68,400×10020,833,333.333=0.32832kNmmHorizontal component: MyIp=68,400×15020,833,333.333=0.49248kNmm

The source uses cosφ=100r≈0.555 for the angle between the vertical direct shear and the tangential torsion force.

The corner radius itself is not the force direction.

Mechanism detailsA weld group is a set of lines1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
  2. Use line lengths for centroid weighting.

    Line second moments have units .

    Add the parallel-axis terms.

  3. Direct force per length is .

    The eccentric moment adds tangential flow proportional to distance from the centroid.

  4. Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.

5. Add components and calculate the maximum

Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Add arrows before taking the magnitude

Walking east and walking north do not point in the same direction.

Add arrows before taking the magnitude — Walking east and walking north do not point in the same direction.

Sketch, not to scale; use the original dimensions.

  1. Choose signed horizontal and vertical directions.
  2. Add contributions along each direction separately.
  3. For perpendicular components, use the right-triangle resultant.

Remember: Check the corner where direct and torsional components reinforce each other.

Related concept and full method

qvertical=0.228+0.32832=0.55632kNmmqmax=0.556322+0.492482=0.742986kNmm

The opposite column of weld has vertical components subtracting, hence a smaller resultant.

The upper and lower right corners have the same maximum magnitude.

Mechanism detailsA weld group is a set of lines1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
  2. Use line lengths for centroid weighting.

    Line second moments have units .

    Add the parallel-axis terms.

  3. Direct force per length is .

    The eccentric moment adds tangential flow proportional to distance from the centroid.

  4. Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.

6. Size the fillet and check its resistance

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why the weld throat is smaller than its leg

The shortest cut through the weld is thinner than the outside leg.

Why the weld throat is smaller than its leg — The shortest cut through the weld is thinner than the outside leg.

Sketch, not to scale; use the original dimensions.

  1. For the stated equal-leg 90° fillet, throat is approximately 0.7 × leg.
  2. Multiply throat area by the matching weld design strength.
  3. For force per length, use a one-millimetre weld strip.

Remember: Choose strength from both the steel grade and electrode class.

Related concept and full method

srequired=1,000qmax0.7pw=1,000×0.7429860.7×250=4.24564mmThe lecturer selects s=6mm. qcapacity=0.7×6×2501,000=1.05kNmm>0.742986Weld strength passes.

The closed four-side weld is treated as the full line rectangle by the source method.

This differs from separately terminated side welds with 2s start/end deductions.

The plate thickness is absent.

Therefore, the numerical strength result is complete but minimum/maximum permitted leg size cannot be confirmed from Table 9.1/edge-thickness rules.

The 6mm choice is the lecturer’s selection, conditional on those missing detailing inputs.

Mechanism detailsFrom fillet leg to effective throat1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. An equal-leg fillet between perpendicular plates has an approximately right-triangular section.
  2. For this geometry, throat .

    It is shorter than the leg.

  3. Effective resisting area = .

    With here, capacity per length is .

  4. Use the course end allowances, minimum size and length rules; increasing the geometric length alone does not resolve every detailing check.

Result and concise exam wording

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

P=228kN,e=300mm,L=1,000mm,Ip,line=20.83333×106mm3.

qs=0.228; torsion components 0.32832 vertical and 0.49248 horizontal kN/mm.

qmax=0.742986kNmm.

s≥4.246mm;6mm fillet supplies 1.05kNmm and passes weld strength.

Plate-thickness detailing remains unverified because it is not given.

Misconceptions and checks

Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Apply the reasoning to this section’s data and conditions

  • The two 300mm dimensions mean different things: height and eccentricity.
  • Use line inertia in mm3, not solid-plate inertia in mm4.
  • The dashed right edge still belongs to the stated four-side weld.
  • Do not certify minimum/maximum weld size without the plate thickness.

How the method transfers to a new variant

Use the same mechanism: Treat a weld group as lines. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Use the same mechanism: Add force components at each bolt. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Apply the reasoning to this section’s data and conditions

  1. Identify every actual weld line and its load path.
  2. Find centroid, length and line inertias.
  3. Measure load eccentricity from the centroid.
  4. Calculate direct and torsional components and the critical resultant.
  5. Solve for leg size and check detailing separately.

Prediction with explained answer

Use the same mechanism: The weld resists through its throat. At fixed weld strength, doubling the leg doubles throat and line resistance in this model. Detailing limits can prevent that choice.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Keep the same load and rectangle but move the load line through the weld centroid.

Find required strength and leg by strength alone.

Answer and reasoning

e=0 so torsion vanishes.

q=2281,000=0.228kNmm.

s≥1,000×0.228175=1.303mm by strength alone.

The actual selected leg is still controlled by minimum/detailing rules; a 1.3mm design cannot be adopted just from this strength result.

Mechanism detailsA weld group is a set of lines1 concept · 3 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The centre is empty: resistance comes from the weld lines, not a solid plate filling the group.
  2. Use line lengths for centroid weighting.

    Line second moments have units .

    Add the parallel-axis terms.

  3. Direct force per length is .

    The eccentric moment adds tangential flow proportional to distance from the centroid.

  4. Combine signed components at every candidate corner, then compare the maximum with throat resistance per length.