STEELWORK / CON4334
Worked examples

Connection example 5: separate moment and shear bolt groups

Diagrams, explanations and answers are presented in reading order. No playback or response is required.

← Read this lecture example beside its chapter concepts

All answers shownChinese–English terminology
Diagrams, explanations and answers are presented in reading order. No playback or response is required.

Design the bolt groups joining a 610×229×140 UB floor beam to a 254×254×132 UC. Steel is S355 and bolts are Grade 8.8 M24. Characteristic moments are 160kN·m dead and 90kN·m imposed; characteristic shears are 250kN dead and 160kN imposed.

Original source: LectureNotes/Ch 2_Connection.pdf — p. 29, p. 30.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

A force couple carries moment

Separate the force couple used to carry moment from the force used to carry web shear.

The flange forces act in opposite directions. Their separation z gives the lever arm. The web arrow represents shear.
The flange forces act in opposite directions. Their separation z gives the lever arm. The web arrow represents shear.

Prediction, then explanation. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Moment is force multiplied by perpendicular separation. Divide the required moment by the specified separation to obtain each couple force.

F=M/zF=M/z

M is moment in kN·mm; z is the specified force-line separation in mm; F is force in kN.

Scope. Use the lever arm defined by the source model. Do not silently replace it with overall section depth or another geometric distance.

Check and takeaway. Check flange welds for the couple forces and web welds for the stated shear model. Both force paths need a satisfactory detail.

Follow contact pressure into the plate

The bolt may survive shear while the connected plate deforms or tears near the hole.

The labels distinguish bolt diameter d from hole diameter d₀. The arrow at the hole edge shows the bearing contact action.
The labels distinguish bolt diameter d from hole diameter d₀. The arrow at the hole edge shows the bearing contact action.

Prediction, then explanation. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

Calculate every bound required by the supplied rule. The smallest applicable bound limits the connection at that layer.

Pbearing≤pbsdtP_{bearing}\le p_{bs}dt

pbs is the applicable bearing strength in N/mm²; d is nominal bolt diameter in mm; t is plate thickness in mm.

Scope. This diameter term alone is not the complete check. End-distance and clear-ligament limits, bolt bearing and each connected layer also matter.

Check and takeaway. Two covers and one main plate do not necessarily have the same thickness or strength. Compare the actual force share in each layer.

A bolt diameter is not a hole diameter

Check that bolts fit and leave enough material between holes and plate boundaries.

pdd₀Clear ligament
The inner circle represents bolt diameter d. The outer circle represents hole diameter d₀. Pitch and gauge join hole centres.

Prediction, then explanation. At fixed pitch, a larger hole leaves a shorter clear ligament. Increasing bolt diameter may also increase minimum edge-distance requirements.

Measure pitch along the bolt line and gauge across lines. Distinguish end distance along the load from edge distance across it.

lc=p−d0l_c=p-d_0

lc is clear ligament between holes; p is centre-to-centre pitch; d₀ is hole diameter. All use mm.

Scope. Apply the supplied edge-preparation and minimum/maximum spacing rules. Passing a bearing calculation does not prove the layout passes.

Check and takeaway. For pitch 60 mm and hole diameter 22 mm, the ligament is 38 mm. Using a 20 mm bolt diameter here gives the wrong ligament.

Apply the reasoning to this section’s data and conditions

InputOrigin
Given actionsSeparate moment and shear dead/imposed components in question table; factor each once.
Given force-couple arm595mm between flange force lines in lecturer diagram/solution; not the nominal 610mm beam depth.
Selected fastenersFour upper flange bolts; four lower for opposite moment direction; eight web bolts, all M24.
Selected bearing detail

Lecturer p.30 selects 12mm end plate,55mm end distance and 70mm pitch.

These are design choices, not task givens.

LookupM24 As=353mm2; Grade 8.8 pt=560,ps=375,pbb=1,000; S355 pbs=550,Us=510; Ub=800Nmm2.

Why this method applies

Add force components at each bolt

An in-plane load acts away from the bolt-group centre. Find the largest resultant bolt force.

The direct-force arrows are parallel. The moment-force arrows run tangentially around the bolt-group centre.
The direct-force arrows are parallel. The moment-force arrows run tangentially around the bolt-group centre.

Prediction, then explanation. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Locate the bolt-group centre and coordinates. Add horizontal components together and vertical components together before finding each resultant.

M=Pe,J=∑(xi2+yi2),FMx=−Myi/J,FMy=Mxi/JM=Pe,\quad J=\sum(x_i^2+y_i^2),\quad F_{Mx}=-My_i/J,\quad F_{My}=Mx_i/J

e, xi and yi use mm; J uses mm². With M in kN·mm, each moment-force component is in kN.

Scope. These expressions use the stated elastic, equal-bolt in-plane model. Out-of-plane tension and prying require another model.

Check and takeaway. Do not add force magnitudes before resolving directions. Two perpendicular forces of 3 and 4 kN give 5 kN, not 7 kN.

Use the same mechanism: A force couple carries moment. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Apply the reasoning to this section’s data and conditions

Use the source idealisation: bending is a tension/compression force couple at the flanges; vertical shear is carried by a separate web-bolt group.

Moment divided by the perpendicular couple arm gives flange force.

Because groups have separate assigned actions, do not distribute the flange tensile force among the web bolts.

1. Design the tension flange group

An eccentric bracket pulls bolts differently

An out-of-plane moment rotates the bracket about the stated pivot. Determine the bolt tension pattern.

The pivot is the compression reference. Bolts farther from it have longer lever arms in the course elastic model.
The pivot is the compression reference. Bolts farther from it have longer lever arms in the course elastic model.

Prediction, then explanation. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Use compatibility to relate tension to distance. Moment equilibrium then determines the proportionality factor.

Ft,i=Myi∑yj2F_{t,i}=\frac{My_i}{\sum y_j^2}

M is moment in kN·mm. yi is distance from the stated pivot in mm. Ft,i is tension in kN.

Scope. Apply only to the stated active bolt set and pivot model. Flexible plates can create prying; use the supplied assumptions and resistance definitions.

Check and takeaway. A bolt’s lever arm is measured from the pivot used in the equation. It is not automatically its distance from the group centroid.

Use the same mechanism: A force couple carries moment. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Apply the reasoning to this section’s data and conditions

Physical interpretation: How two flange forces make a moment

Two opposite forces form a turning pair, like two hands turning a wheel.

How two flange forces make a moment — Two opposite forces form a turning pair, like two hands turning a wheel.

Sketch, not to scale; use the original dimensions.

  1. Identify the separation between their actual force lines.
  2. Required force equals moment divided by that separation.
  3. Design the relevant flange group for that force.

Remember: The force-line separation is not automatically the overall section depth.

Related concept and full method

M=1.4×160+1.6×90=224+144=368kN·mFflange=Mz=3680.595=618.487kNPnom,one=0.8×560×3531,000=158.144kNn≥618.487158.144=3.911→select4Nominal tension resistance of the whole group: Pnom=4×158.144=632.576kN>618.487Passes.

For the moment direction shown, the lower flange region supplies compression and the upper group tension.

The extra lower four bolts are not added to the upper group’s capacity; they provide the corresponding group for the opposite moment direction/detail.

Mechanism detailsOut-of-plane bolt tension and prying2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A bracket moment can create compression at the plate contact and tension in the bolt rows.
  2. The original assumed pivot/compression line determines each row distance.
  3. Under the elastic row model, a farther tension row attracts more tension.

    Direct shear may act simultaneously.

  4. Flexible plates can add prying force.

    Use nominal tension and interaction rules exactly as specified by the course.

2. Design the shear group

Count cuts through each loaded bolt

Find how many shear planes transfer the force through one side of the connection.

The middle plate moves against two cover plates. The two interfaces cut each bolt at two planes.
The middle plate moves against two cover plates. The two interfaces cut each bolt at two planes.

Prediction, then explanation. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Select the area at the actual shear plane. Multiply by bolt shear strength. Count only the bolts and planes in the same transfer stage.

Ps=psAs,Pgroup=nbnsPsP_s=p_sA_s,\qquad P_{group}=n_b n_s P_s

ps is bolt shear strength in N/mm²; As is the appropriate area in mm². nb counts bolts; ns counts equally loaded shear planes.

Scope. Use the thread area when threads cross the plane as required. Check bearing, plate failure and detailing separately.

Check and takeaway. Both halves of a butt splice carry the full transmitted force in sequence. Counting both halves together would double the apparent resistance.

Use the same mechanism: A force couple carries moment. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Count where the bolt can be sheared

The plate interfaces are the places trying to cut across the bolt.

Count where the bolt can be sheared — The plate interfaces are the places trying to cut across the bolt.

Sketch, not to scale; use the original dimensions.

  1. Count actual loaded shear planes, not merely visible plates.
  2. Choose shank or threaded area for the plane concerned.
  3. Compare group resistance with the force that group transfers.

Remember: Bolts on opposite sides of a splice do not all act in parallel.

Related concept and full method

V=1.4×250+1.6×160=350+256=606kNPs,one=375×3531,000=132.375kNFor 8 web bolts, demand per bolt: 6068=75.75kNPs,group=8×132.375=1,059.0kN>606Passes.

Mechanism detailsCount the bolt shear planes2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Load must cross an interface between the connected plates.
  2. A lap joint gives one shear plane through a bolt.
  3. A symmetric double-cover joint may provide two shear planes.

    Count load-transfer interfaces, not just visible plates.

  4. Use the source’s area and shear strength.

    Then check bearing, plate resistance and detailing separately.

3. Check selected end-plate bearing

Use the same mechanism: Follow contact pressure into the plate. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

Apply the reasoning to this section’s data and conditions

Use d=24mm and standard hole d0=26mm.

The chosen 12mm plate and 70mm pitch give clear ligament 44mm.

The chosen end distance is 55mm.

Pbb=24×12×1,0001,000=288kNlc=70−26=44mmB1=24×12×5501,000=158.4kNB2=0.5×55×12×5501,000=181.5kNNet-clearance term between holes: 1.5×44×12×5101,000=403.92kNUpper cap: 2×24×12×8001,000=460.8kNPbs=min(158.4,181.5,403.92,460.8)=158.4kN

Both bearing resistances exceed the 75.75kN per-bolt demand and also exceed the 132.375kN shear resistance, so shear governs the web group.

Mechanism detailsBearing and the remaining ligament1 concept · 3 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Force transfers through contact between bolt and connected plate.
  2. The plate around the hole carries bearing stress.

    Bolt bearing and plate bearing are separate checks.

  3. A short ligament can tear out towards the end.

    The direction of force determines the relevant edge.

  4. Evaluate every specified bearing and ligament bound for each layer and retain the smallest applicable resistance.

4. State what has actually been designed

Use the same mechanism: A force couple carries moment. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Use the same mechanism: Count cuts through each loaded bolt. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Apply the reasoning to this section’s data and conditions

Physical interpretation: What to do when one input is missing

A calculator cannot supply a dimension that the drawing never gave.

What to do when one input is missing — A calculator cannot supply a dimension that the drawing never gave.

Sketch, not to scale; use the original dimensions.

  1. Separate given values, table values and calculated values.
  2. Complete the checks whose required inputs are available.
  3. State the missing input beside the remaining conditional result.

Remember: An illustrative assumption must not become an unstated exam given.

Related concept and full method

The flange tension and web shear/bearing bolt checks pass under the source’s force-couple idealisation.

The source explicitly says only bolts have been designed; welds, end plates, stiffeners, column flange and column web require separate design.

The 12mm end-plate bearing calculation is not a complete end-plate bending/prying check.

Mechanism detailsSeparate the moment couple and shear5 concepts

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A simplified moment connection assigns different actions to different fastener groups.
  2. Opposite flange forces separated by z resist moment: .
  3. The web fasteners or welds carry the assigned vertical shear in this model.
  4. Flange force, web shear, plate bearing and detailing each need their specified checks.

Result and concise exam wording

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Use the same mechanism: Follow contact pressure into the plate. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

Test every possible fracture cut

Find the remaining steel area across a candidate tension-failure path.

The dashed fracture line crosses two hole centres. Subtract only the holes crossed by that candidate line.
The dashed fracture line crosses two hole centres. Subtract only the holes crossed by that candidate line.

Prediction, then explanation. At fixed plate size, larger holes reduce the straight-path net area. A diagonal path needs its own stagger correction.

Subtract the hole widths crossed by the path, then multiply by thickness. Compare all plausible paths using the applicable course rule.

An=(b−nd0)tA_n=(b-nd_0)t

An is net area in mm²; b is plate width; d₀ is hole diameter; t is thickness, all in mm. n counts holes on this straight path.

Scope. This expression is for a straight cut. Effective area can require further shear-lag rules. Gross, net and effective areas must remain distinct.

Check and takeaway. Use the hole diameter, not the bolt diameter, when removing missing steel. The plate contains a hole, not solid steel around the bolt shank.

Apply the reasoning to this section’s data and conditions

ULS M=368kN·m; flange force=618.487kN.

Four M24 Grade 8.8 flange bolts give nominal tension 632.576kN.

ULS V=606kN; eight M24 web bolts give shear 1,059.0kN.

Selected 12mm plate gives bolt bearing 288kN and plate bearing 158.4kN per bolt, both>75.75kN.

Bolts pass; remaining connection components are outside the source calculation.

Misconceptions and checks

Use the same mechanism: A force couple carries moment. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Use the same mechanism: Test every possible fracture cut. At fixed plate size, larger holes reduce the straight-path net area. A diagonal path needs its own stagger correction.

Apply the reasoning to this section’s data and conditions

  • Use 595mm force-couple arm, not nominal beam depth 610mm.
  • Do not add bottom compression-side bolts to the upper tensile group.
  • Do not call the end plate fully designed after checking only bearing.

How the method transfers to a new variant

Use the same mechanism: A force couple carries moment. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Use the same mechanism: Follow contact pressure into the plate. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

Apply the reasoning to this section’s data and conditions

  1. Factor moment and shear components separately.
  2. Resolve bending moment into flange force using the stated couple arm.
  3. Size the tension group using nominal bolt tension.
  4. Assign shear to the web group and check its bearing path.
  5. Document which other joint components are not included in the bolt-only exercise.

Prediction with explained answer

Use the same mechanism: An eccentric bracket pulls bolts differently. For unchanged geometry, doubling the applied moment doubles the modelled bolt tensions. Changing the pivot changes the distribution.

Use the same mechanism: Test every possible fracture cut. At fixed plate size, larger holes reduce the straight-path net area. A diagonal path needs its own stagger correction.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

If the ultimate moment becomes 400kN·m, keeping 595mm arm and four flange bolts, is the tension group adequate?

Answer and reasoning

F=4000.595=672.269kN>632.576kN, so no.

Required count≥672.269158.144=4.251; at least 5 by strength alone.

However, the final symmetric layout and plate/prying design must also be revised.

Mechanism detailsOut-of-plane bolt tension and prying1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A bracket moment can create compression at the plate contact and tension in the bolt rows.
  2. The original assumed pivot/compression line determines each row distance.
  3. Under the elastic row model, a farther tension row attracts more tension.

    Direct shear may act simultaneously.

  4. Flexible plates can add prying force.

    Use nominal tension and interaction rules exactly as specified by the course.