STEELWORK / CON4334
Crash course · Section B

Unrestrained beams (LTB): a table routine for each segment

The first 7 marks (reactions, shear and moment diagrams) use the same skills as the compulsory floor beams. The other 23 marks are one fixed “look-up routine”, repeated for each segment. Once the routine is smooth, this is the safest Section B question.

What is lateral-torsional buckling (LTB)? Always examined

A beam can escape sideways
The compression flange moves sideways while the section twists.

Concept map

Lateral-torsional buckling: why does a beam tip over sideways?

Understand the mechanism and the LTB calculation starts to make sense: every formula measures how easily the compression flange can escape sideways. The mechanism runs down the middle, with what makes it worse and how design responds.

Text version (from cause to result)

  1. Cause

    The beam bends

    In sagging the top flange is compressed and the bottom flange stretched; in hogging (e.g. a cantilever) the bottom flange is compressed.

  2. Key idea

    The compression flange acts like a slender strut

    The compressed flange behaves like a slender strut that wants to bow sideways — about the weak axis of the section.

  3. Key idea

    It bows sideways and twists

    The tension flange wants to stay straight while the compression flange moves sideways, so the whole section moves sideways and twists. That is lateral-torsional buckling.

    The compression flange moves sideways while the section twists
  4. How design deals with itWhere marks are lost

    Lateral restraint (×): holds the compression flange at the side

    Restraints split the beam into segments; shorter segments are safer. A restraint counts if it can resist 2.5% of the largest compression-flange force.

    A lateral restraint holds the compression flange
  5. Result

    Mb<McM_b<M_c Fails before the section is fully used

    The beam fails sideways before reaching its section moment capacity McM_c, so it is checked against the smaller MbM_b.

  6. What changes it

    LEL_E Longer unrestrained length

    The longer the flange is free between lateral restraints, the more easily it bows out. With normal loads LEL_E is the segment length.

  7. What changes it

    ryr_y Weak-axis stockiness

    The smaller ryr_y (the narrower the flange), the easier it bows sideways. A narrow-flanged UB is more prone to LTB than a UC.

  8. What changes it

    Load on the top flange that moves with it

    Once the beam twists, the load pushes it over further (destabilizing load), so LE×1.2L_E\times1.2. Exam questions usually state “normal load”.

  9. What changes it

    mLTm_{LT} Shape of the moment diagram

    A segment near the peak moment all along is most dangerous; a single peak is less so. mLT≤1m_{LT}\le1 turns an uneven moment into an equivalent uniform one.

    Same peak moment, a longer high-moment zone is more dangerous
  10. How design deals with it

    A slab holds it all along → no LTB check

    A slab restrains the beam along its whole length (full lateral restraint), so the compulsory floor beams need no LTB check — but still need shear, bending and deflection.

  11. How design deals with it

    mLTM≤Mbm_{LT}M\le M_b Restrained at a few points → check each segment

    All the factors above end up in one check: LEL_E and ryr_y → λLT\lambda_{LT} → pbp_b → MbM_b; the moment shape → mLTm_{LT}. Steps: LTB calculation map.

  12. Exam answer

    Exam: tell supports from restraints first

    On the drawing: triangle / roller = support (reaction); cross × = lateral restraint (no reaction, only splits segments). “Fully restrained” means no LTB check.

Tour steps

  1. 1. The compression flange is a strut

    The beam bends → one flange is compressed → like a slender column it wants to bow sideways.

  2. 2. Sideways plus twist

    The tension flange does not follow, so the section moves sideways and twists, failing before McM_c.

  3. 3. What makes it worse?

    A long unrestrained length, a slim weak axis, load on the top flange, and a segment near the peak moment all along.

  4. 4. The remedy: lateral restraint

    Hold the compression flange at the side to shorten the unrestrained length. A slab holding it all along → no LTB check.

  5. 5. Everything ends in one check

    Everything becomes mLTM≤Mbm_{LT}M\le M_b, written once per segment.

  6. 6. The first exam step

    First separate supports from lateral restraints on the drawing — the most common mistake starts here.

What does this question test? Always examined

Part (2024)MarksWhat to do
(a)3support reactions
(b)4shear-force and bending-moment diagrams (with values)
(c)13LTB check of the first segment (BC)
(d)10LTB check of the second segment (CD)

The method Always examined

  1. Reactions (take moments)

    Only points drawn with a support symbol have reactions; ignore the restraint crosses ×. The loads are usually already factored (the question says “factored”).

  2. Shear-force and bending-moment diagrams

    Work out the shear on both sides of each load and the moment at each load. Where the shear changes from positive to negative is the maximum moment. See core skills §3.

  3. Design strength and class

    pyp_y from the flange thickness TT; Class 1 or 2 → βw=1\beta_w=1.

  4. Effective length LEL_E of each segment

    Normally (normal load, restraints at both ends): LE=L_E= segment length. If the load sits on the top flange and can move with it (destabilizing): ×1.2. Cantilever segments: use Table 8.1.

  5. Slenderness

    λ=LEryv=1[1+0.05(λ/x)2]0.25λLT=u v λβw\lambda=\frac{L_E}{r_y}\qquad v=\frac{1}{\left[1+0.05\left(\lambda/x\right)^2\right]^{0.25}}\qquad\lambda_{LT}=u\,v\,\lambda\sqrt{\beta_w}
  6. Look up pbp_b and work out MbM_b

    pb  interpolated in Table 8.3a, py columnMb=pbSx1000  (kN⋅m)p_b\;\text{interpolated in Table 8.3a, }p_y\text{ column}\qquad M_b=\frac{p_bS_x}{1000}\;(\text{kN·m})
  7. Equivalent moment factor mLTm_{LT}

    If the moment diagram in the segment is curved (there is a UDL), use the quarter-point formula:

    mLT=0.2+0.15∣M2∣+0.5∣M3∣+0.15∣M4∣∣Mmax⁡∣  ≥0.44m_{LT}=0.2+\frac{0.15|M_2|+0.5|M_3|+0.15|M_4|}{|M_{\max}|}\;\ge0.44

    M2,M3,M4M_2,M_3,M_4 are the moments at ¼, ½ and ¾ of this segment; Mmax⁡M_{\max} is the largest moment in the segment. If the diagram is a straight line you may use mLT=0.6+0.4β≥0.44m_{LT}=0.6+0.4\beta\ge0.44 (β\beta = ratio of the end moments).

  8. Compare

    mLT Mmax⁡≤Mb  ⇒  OKm_{LT}\,M_{\max}\le M_b\;\Rightarrow\;\text{OK}

Understanding map

LTB check: where every number comes from and where it goes

The hardest part of the LTB question is knowing which number goes into which formula. Read the map from top to bottom in answer order: numbers from the question and the tables at the top, the conclusion at the bottom. The values are from 2024 BQ4, segment BC (4 m).

Text version (in working order)

  1. From the questionWhere marks are lost

    LBCL_{BC} Segment length

    Lateral restraints split the beam into segments, each checked on its own. Segment BC runs from B (3.5 m) to C (7.5 m).

  2. From the questionWhere marks are lost

    PP, ww Loads and supports

    The design loads (already factored) and where the supports are. Only points drawn with a support symbol have reactions.

    2024 BQ4 (segment BC)

    100 kN at 3.5 m,  200 kN at 7.5 m,  1.4 kN/m;  supports A, D100\text{ kN at }3.5\text{ m},\;200\text{ kN at }7.5\text{ m},\;1.4\text{ kN/m};\;\text{supports A, D}
  3. From the tablesWhere marks are lost

    ryr_y Minor-axis radius of gyration

    How “stocky” the section is about its weak axis. The larger it is, the harder it is to bow sideways.

    Where it comes from: Section table (5.03 cm → 50.3 mm).

  4. Worked out

    LEL_E Effective length

    Normal load with restraints at both ends → LE=L_E= segment length. Load on the top flange that can move sideways with it (destabilizing) → ×1.2. Cantilevers: Table 8.1.

    Formula

    LE=1.0L  (normal)or1.2L  (destabilizing)L_E=1.0L\;(\text{normal})\quad\text{or}\quad1.2L\;(\text{destabilizing})

    2024 BQ4 (segment BC)

    LE=1.0×4000=4000 mmL_E=1.0\times4000=4000\text{ mm}
  5. Worked out

    RAR_A, RDR_D Support reactions

    Take moments about one support to find the other reaction; the two must add up to the total load.

    Formula

    ∑MA=0  ⇒  RDRA=∑P−RD\textstyle\sum M_A=0\;\Rightarrow\;R_D\qquad R_A=\sum P-R_D

    2024 BQ4 (segment BC)

    11RD=100(3.5)+200(7.5)+15.4(5.5)=1934.7  ⇒  RD=175.88,  RA=139.52 kN11R_D=100(3.5)+200(7.5)+15.4(5.5)=1934.7\;\Rightarrow\;R_D=175.88,\;R_A=139.52\text{ kN}
  6. From the tablesWhere marks are lost

    pyp_y Design strength

    Look it up from the grade and the flange thickness TT. S355 with a flange thicker than 16 mm gives 345.

    2024 BQ4 (segment BC)

    T=22.1>16  ⇒  py=345 N/mm2T=22.1>16\;\Rightarrow\;p_y=345\text{ N/mm}^2

    Where it comes from: Data File design-strength table; TT from the section table. Core skills §5

  7. From the tablesWhere marks are lost

    xx Torsional index

    A measure of how the section resists twisting; used only in the vv formula.

    Where it comes from: Same section-table row.

  8. Worked outWhere marks are lost

    λ\lambda Slenderness

    Length compared with stockiness. The larger it is, the more slender the segment and the easier it buckles.

    Formula

    λ=LEry\lambda=\frac{L_E}{r_y}

    2024 BQ4 (segment BC)

    400050.3=79.52\frac{4000}{50.3}=79.52
  9. Worked out

    M(x)M(x) Bending-moment diagram

    Work out the shear and moment point by point from the reactions. Where the shear changes from positive to negative is the maximum moment.

    Formula

    M(x)=RAx−wx22−∑Pi⟨x−ai⟩M(x)=R_Ax-\tfrac{wx^2}{2}-\textstyle\sum P_i\langle x-a_i\rangle

    2024 BQ4 (segment BC)

    MB=479.74,MC=607.01 kN⋅m (max)M_B=479.74,\quad M_C=607.01\text{ kN·m (max)}

    Where it comes from: Method: core skills §3.

  10. Worked out

    βw\beta_w Section factor

    Class 1 or 2 section → βw=1\beta_w=1. Classification uses ε\varepsilon, which comes from pyp_y.

    Where it comes from: Section classification (core skills §6).

  11. From the tables

    uu Buckling parameter

    A section-shape factor, read straight from the table.

    Where it comes from: Same section-table row.

  12. Worked out

    vv Slenderness factor

    A correction for twisting of the section, set by λ/x\lambda/x; always below 1.

    Formula

    v=1[1+0.05(λ/x)2]0.25v=\frac{1}{\left[1+0.05(\lambda/x)^2\right]^{0.25}}

    2024 BQ4 (segment BC)

    [1+0.05(79.5230.6)2]−0.25=0.930\left[1+0.05\left(\tfrac{79.52}{30.6}\right)^2\right]^{-0.25}=0.930
  13. Worked outWhere marks are lost

    M2M_2, M3M_3, M4M_4 Quarter-point moments

    The moments at ¼, ½ and ¾ of this segment. For BC that is 1, 2 and 3 m from B, i.e. 4.5, 5.5 and 6.5 m from A.

    2024 BQ4 (segment BC)

    M2=513.66,M3=546.18,M4=577.29 kN⋅mM_2=513.66,\quad M_3=546.18,\quad M_4=577.29\text{ kN·m}
  14. Demand

    Mmax⁡M_{\max} Largest moment in segment

    The largest moment (ignoring sign) inside this segment. For BC it is at C.

  15. Worked out

    λLT\lambda_{LT} Equivalent slenderness

    Slenderness that also accounts for the section shape (u,vu,v). This is the number used to look up pbp_b.

    Formula

    λLT=u v λβw\lambda_{LT}=u\,v\,\lambda\sqrt{\beta_w}

    2024 BQ4 (segment BC)

    0.875×0.930×79.52×1=64.700.875\times0.930\times79.52\times1=64.70
  16. Worked out

    mLTm_{LT} Equivalent moment factor

    Turns an uneven moment into an equivalent uniform one. Close to the peak all along → near 1; peak at one point only → smaller, but never below 0.44.

    Formula

    mLT=0.2+0.15∣M2∣+0.5∣M3∣+0.15∣M4∣∣Mmax⁡∣≥0.44m_{LT}=0.2+\frac{0.15|M_2|+0.5|M_3|+0.15|M_4|}{|M_{\max}|}\ge0.44

    2024 BQ4 (segment BC)

    0.2+0.15(513.66)+0.5(546.18)+0.15(577.29)607.01=0.9190.2+\frac{0.15(513.66)+0.5(546.18)+0.15(577.29)}{607.01}=0.919
  17. From the tables

    SxS_x Plastic modulus

    The modulus of the fully yielded section (cm³); it turns the strength pbp_b into a moment.

    Where it comes from: Section table, the 610×229×140 UB row.

  18. Worked outWhere marks are lost

    pbp_b Bending strength

    Interpolate in Table 8.3a, in the pyp_y column, using λLT\lambda_{LT}. The larger λLT\lambda_{LT} (more slender), the smaller pbp_b.

    Formula

    pb=p1+λLT−λ1λ2−λ1(p2−p1)p_b=p_1+\frac{\lambda_{LT}-\lambda_1}{\lambda_2-\lambda_1}(p_2-p_1)

    2024 BQ4 (segment BC)

    251+64.70−605×(234−251)=235.0 N/mm2251+\frac{64.70-60}{5}\times(234-251)=235.0\text{ N/mm}^2

    Where it comes from: Data File p.5, Table 8.3a, py=345p_y=345 column.

  19. Demand

    mLTMmax⁡m_{LT}M_{\max} Equivalent moment (demand)

    The moment this segment really has to carry; it is compared with MbM_b at the end.

    2024 BQ4 (segment BC)

    0.919×607.01=558.1 kN⋅m0.919\times607.01=558.1\text{ kN·m}
  20. Capacity

    MbM_b Buckling resistance moment

    The largest moment this segment can carry before it buckles sideways.

    Formula

    Mb=pbSx1000  (kN⋅m)M_b=\frac{p_bS_x}{1000}\;(\text{kN·m})

    2024 BQ4 (segment BC)

    235.0×41421000=973.4 kN⋅m\frac{235.0\times4142}{1000}=973.4\text{ kN·m}
  21. Check

    mLTMmax⁡m_{LT}M_{\max} ≤Mb\le M_b Segment BC conclusion

    If the demand is not larger than the capacity, the segment passes. Write this conclusion for every segment.

    2024 BQ4 (segment BC)

    558.1 kN⋅m<973.4 kN⋅m  ✓558.1\text{ kN·m}<973.4\text{ kN·m}\;\checkmark

Tour steps

  1. 1. Find the segment

    Read the drawing: supports give reactions; restraint crosses (×) split the beam into segments. BC is 4 m long, and everything below is worked out for this segment only.

  2. 2. Reactions and moment diagram (7 marks)

    The same skill as the compulsory floor beams: take moments for the reactions, then work out shear and moment at each point and label them.

  3. 3. The demand on this segment

    Take the quarter-point moments and the maximum inside the segment, work out mLTm_{LT}, then multiply by Mmax⁡M_{\max} to get the demand, 558.1 kN·m.

  4. 4. One trip to the tables

    Copy Sx,ry,u,xS_x,r_y,u,x from the same section-table row; pyp_y from TT; Class 1 → βw=1\beta_w=1.

  5. 5. From length to slenderness

    LEL_E comes from the segment length; λ=LE/ry\lambda=L_E/r_y; vv comes from λ/x\lambda/x.

  6. 6. Equivalent slenderness

    λLT=uvλβw\lambda_{LT}=uv\lambda\sqrt{\beta_w} — four arrows meet here, and this is the number for the table.

  7. 7. Look up pbp_b, work out MbM_b

    Interpolate pbp_b in the 345 column of Table 8.3a, then multiply by SxS_x to get the capacity MbM_b.

  8. 8. Compare and conclude

    558.1 < 973.4 → segment BC passes. Walk the same path again for CD (2024 answer: 365.8 < 1075.1 ✓).

Why the shape of the moment diagram matters
The same peak moment is more dangerous when a long stretch stays close to it; mLTm_{LT} reflects this.
Common cases (no intermediate restraint)mLTm_{LT}
simply supported segment, one central point load0.85
simply supported segment, full-length UDL0.93
straight-line diagram, zero at one end, maximum at the other (β=0\beta=0)0.60
cantilever segment (no intermediate restraint)1.00

Walkthrough: 2024 BQ4 (30 marks) Always examined

Given: an 11 m simply supported 610×229×140 UB, S355, Class 1. Design loads: 100 kN at B (3.5 m from A), 200 kN at C (7.5 m from A), and 1.4 kN/m over the whole span (self-weight included). Lateral restraints at A, B, C and D; only A and D are supports. All loads are already factored.

2024 BQ4 original figure: 11 m simply supported beam with point loads at B and C
Original figure: only A and D are supports; A, B, C and D are lateral restraints (×), which split the beam into three segments.

From the table: T=22.1T=22.1, Sx=4142 cm3S_x=4142\text{ cm}^3, ry=50.3 mmr_y=50.3\text{ mm}, u=0.875u=0.875, x=30.6x=30.6.

Past-paper walkthrough

(a) Reactions — 3 marks

11RD=100×3.5+200×7.5+(1.4×11)×5.5=1934.7  ⇒  RD=175.88 kN11R_D=100\times3.5+200\times7.5+(1.4\times11)\times5.5=1934.7\;\Rightarrow\;R_D=175.88\text{ kN}RA=100+200+15.4−175.88=139.52 kNR_A=100+200+15.4-175.88=139.52\text{ kN}

Past-paper walkthrough

(b) Shear-force and bending-moment diagrams — 4 marks

PositionShear (left / right, kN)Moment (kN·m)
A0 / +139.520
B (3.5 m)+134.62 / +34.62479.74
C (7.5 m)+29.02 / −170.98607.01 (max)
D (11 m)−175.88 / 00
2024 BQ4 shear-force diagram (top) and bending-moment diagram (bottom)
The shear changes sign at C, so the moment diagram peaks at C: 607.01 kN·m.
M(x)=139.52x−0.7x2−100⟨x−3.5⟩−200⟨x−7.5⟩M(x)=139.52x-0.7x^2-100\langle x-3.5\rangle-200\langle x-7.5\rangle

The shear changes sign at C → the maximum moment is at C.

Past-paper walkthrough

(c) Segment BC (4 m long) — 13 marks

T=22.1>16⇒py=345;  Class 1⇒βw=1T=22.1>16\Rightarrow p_y=345;\;\text{Class 1}\Rightarrow\beta_w=1

Quarter points (4.5, 5.5, 6.5 m from A): M2=513.66M_2=513.66, M3=546.18M_3=546.18, M4=577.29M_4=577.29, Mmax⁡=607.01 kN⋅mM_{\max}=607.01\text{ kN·m}.

mLT=0.2+0.15(513.66)+0.5(546.18)+0.15(577.29)607.01=0.919mLTMmax⁡=558.1 kN⋅mm_{LT}=0.2+\frac{0.15(513.66)+0.5(546.18)+0.15(577.29)}{607.01}=0.919\qquad m_{LT}M_{\max}=558.1\text{ kN·m}λ=400050.3=79.52v=[1+0.05(79.5230.6)2]−0.25=0.930λLT=0.875×0.930×79.52=64.70\lambda=\frac{4000}{50.3}=79.52\qquad v=\left[1+0.05\left(\tfrac{79.52}{30.6}\right)^2\right]^{-0.25}=0.930\qquad\lambda_{LT}=0.875\times0.930\times79.52=64.70pb=251+64.70−605×(234−251)=235.0 N/mm2Mb=235.0×41421000=973.4 kN⋅mp_b=251+\frac{64.70-60}{5}\times(234-251)=235.0\text{ N/mm}^2\qquad M_b=\frac{235.0\times4142}{1000}=973.4\text{ kN·m}558.1<973.4  ✓558.1<973.4\;\checkmark

Past-paper walkthrough

(d) Segment CD (3.5 m long) — 10 marks

Quarter points (8.375, 9.25, 10.125 m): M2=456.87M_2=456.87, M3=305.65M_3=305.65, M4=153.36M_4=153.36; Mmax⁡=607.01M_{\max}=607.01 (at C).

mLT=0.2+0.15(456.87)+0.5(305.65)+0.15(153.36)607.01=0.603mLTMmax⁡=365.8 kN⋅mm_{LT}=0.2+\frac{0.15(456.87)+0.5(305.65)+0.15(153.36)}{607.01}=0.603\qquad m_{LT}M_{\max}=365.8\text{ kN·m}λ=350050.3=69.58v=0.944λLT=0.875×0.944×69.58=57.48\lambda=\frac{3500}{50.3}=69.58\qquad v=0.944\qquad\lambda_{LT}=0.875\times0.944\times69.58=57.48pb=268+57.48−555×(251−268)=259.6Mb=259.6×41421000=1075.1 kN⋅mp_b=268+\frac{57.48-55}{5}\times(251-268)=259.6\qquad M_b=\frac{259.6\times4142}{1000}=1075.1\text{ kN·m}365.8<1075.1  ✓365.8<1075.1\;\checkmark

Full solution with the drawn diagrams: 2024 BQ4.

How much does one extra restraint help? (2023 PTE) Often examined

A 6 m simply supported 406×140×46 UB with 110 kN at midspan. Same beam, different restraints:

restraints at the ends onlyplus a midspan restraint
segment length LEL_E6 m (one segment)3 m (two segments)
mLTm_{LT}0.85 (central point load)0.60 (straight line, β=0\beta=0)
demand mLTMmax⁡m_{LT}M_{\max}140.3 kN·m99.0 kN·m
λLT\lambda_{LT} → pbp_b140.1 → 79.980.4 → 188.8
MbM_b70.9 kN·m → fails167.7 kN·m → passes

Halving the segment more than doubles the resistance. That is why floor beams held by the slab (fully restrained) need no LTB check. Solution

Other versions Often examined

A beam with an overhang (2023 FT)

The supports are not at the beam ends; one end sticks out as a cantilever. Find the real supports from the support symbols; the reactions change. The cantilever moment is negative (top flange in tension, bottom flange in compression).

  • Cantilever segment without intermediate restraint: mLT=1.0m_{LT}=1.0.
  • Its LEL_E comes from lecture Table 8.1 (support and tip restraint conditions), not simply the segment length.
  • Between the supports the moment may change from negative to positive; use the largest absolute value.

Solution; Table 8.1 explained.

Destabilizing load

A load applied on the top flange that can move sideways with the beam (e.g. something resting directly on the flange) makes the twisting worse. Then use LE×1.2L_E\times1.2. Questions normally say “normal load”. Explanation

Where marks are usually lost Always examined

Next: try it yourself