STEELWORK / CON4334
Crash course · 0

Core skills: the eight tools every question uses

This page is the foundation of the whole crash course. Every question type later simply combines these tools. Take your time on the first read; each section ends with a quick check.

1. Units: where most mistakes happen Always examined

QuantityUsual unitsConversion
ForceN, kN1 kN=1000 N1\text{ kN}=1000\text{ N}
Lengthmm, m1 m=1000 mm1\text{ m}=1000\text{ mm}
Stress / strengthN/mm² (= MPa)force ÷ area
Bending momentkN·m, N·mm1 kN⋅m=106 N⋅mm1\text{ kN·m}=10^{6}\text{ N·mm}
Line loadkN/m1 kN/m=1 N/mm1\text{ kN/m}=1\text{ N/mm} (exactly equal!)
Area AAcm² → mm²× 100
Section modulus S, ZS,\,Zcm³ → mm³× 1000
Second moment of area IIcm⁴ → mm⁴× 10 000 (10410^4)

Two shortcuts worth memorising:

strength (N/mm2)×area (mm2)÷1000=force (kN)\text{strength}\,(\text{N/mm}^2)\times\text{area}\,(\text{mm}^2)\div 1000=\text{force}\,(\text{kN})py (N/mm2)×S (cm3)÷1000=moment (kN⋅m)p_y\,(\text{N/mm}^2)\times S\,(\text{cm}^3)\div 1000=\text{moment}\,(\text{kN·m})

Quick check: Convert I=21 370 cm4I=21\,370\text{ cm}^4 and M=350 kN⋅mM=350\text{ kN·m} into mm units.

Show answer

I=21 370×104=2.137×108 mm4I=21\,370\times 10^4=2.137\times10^{8}\text{ mm}^4; M=350×106=3.5×108 N⋅mmM=350\times10^{6}=3.5\times10^{8}\text{ N·mm}.

2. Loads: dead, imposed and the load factors Always examined

wdesign=1.4 Gk+1.6 Qkw_{\text{design}}=1.4\,G_k+1.6\,Q_k

From slab thickness to kN/m²

gk=thickness (m)×unit weight (kN/m3)+finishes (kN/m2)g_k=\text{thickness}\,(\text{m})\times\text{unit weight}\,(\text{kN/m}^3)+\text{finishes}\,(\text{kN/m}^2)

Example: 180 mm slab, 24.5 kN/m³ concrete, 0.4 kN/m² finishes: gk=0.18×24.5+0.4=4.81 kN/m2g_k=0.18\times24.5+0.4=4.81\text{ kN/m}^2. Convert the thickness from mm to m first.

From kN/m² (area load) to kN/m (line load): the tributary width

w (kN/m)=area load (kN/m2)×tributary width (m)w\,(\text{kN/m})=\text{area load}\,(\text{kN/m}^2)\times\text{tributary width}\,(\text{m})Interior beam: half of the spacing on each side, s12+s22\tfrac{s_1}{2}+\tfrac{s_2}{2}. Edge beam: one side only, s2\tfrac{s}{2}.

Self-weight of the steel beam

self-weight (kN/m)=mass (kg/m)×g1000\text{self-weight}\,(\text{kN/m})=\frac{\text{mass}\,(\text{kg/m})\times g}{1000}Example: 39.1 kg/m with g=10g=10 gives 39.1×10/1000=0.391 kN/m39.1\times10/1000=0.391\text{ kN/m}. Self-weight is dead load, so it takes the factor 1.4.

Quick check: A 150 mm slab, 24.5 kN/m³ concrete, 0.5 kN/m² finishes, 3 kN/m² imposed load. What is the design area load?

Show answer

gk=0.15×24.5+0.5=4.175g_k=0.15\times24.5+0.5=4.175; design value =1.4×4.175+1.6×3=5.845+4.8=10.645 kN/m2=1.4\times4.175+1.6\times3=5.845+4.8=10.645\text{ kN/m}^2.

3. Reactions, shear and bending moment Always examined

Two standard cases to learn by heart (simply supported beam)

LoadEach reaction = maximum shearMaximum moment (midspan)
Full-span uniform load (UDL) wwwL2\dfrac{wL}{2}wL28\dfrac{wL^2}{8}
Point load PP at midspanP2\dfrac{P}{2}PL4\dfrac{PL}{4}

When both act and both maxima are at midspan, simply add them: Mmax⁡=PL4+wL28M_{\max}=\tfrac{PL}{4}+\tfrac{wL^2}{8}.

Load not in the middle? Take moments

  1. Take moments about the left support A to find RBR_B

    RB L=∑Pi ai+wL⋅L2R_B\,L=\sum P_i\,a_i+wL\cdot\frac{L}{2}
  2. Use vertical equilibrium for RAR_A

    RA=total load−RBR_A=\text{total load}-R_B
  3. The maximum moment is where the shear changes from positive to negative (usually under a point load)

    M(x)=RA x−wx22−∑Pi (x−ai)(loads left of x only)M(x)=R_A\,x-\frac{w x^2}{2}-\sum P_i\,(x-a_i)\quad(\text{loads left of }x\text{ only})

Rules for drawing shear-force (SFD) and bending-moment (BMD) diagrams

  • Under a UDL: the SFD is a sloping straight line and the BMD is a curve.
  • At a point load: the SFD jumps by the size of the load and the BMD has a sharp corner.
  • At a simple support: moment = 0.
  • Where shear = 0 (or changes sign) → maximum moment.

Quick check: An 8 m simply supported beam carries 60 kN at 5 m from A plus 4 kN/m over the full span. Find the reactions.

Hint

Take moments about A so that A’s own reaction drops out of the equation.

Show answer

RB=60×5+(4×8)×48=53.5 kNR_B=\dfrac{60\times5+(4\times8)\times4}{8}=53.5\text{ kN}; RA=60+32−53.5=38.5 kNR_A=60+32-53.5=38.5\text{ kN}. Check: they add up to 92 kN = total load.

Past-paper walkthrough

Full example: the shear-force and bending-moment diagrams of this 8 m beam

Loads, shear-force diagram and bending-moment diagram of the 8 m simply supported beam
Walk from left to right: the shear falls slowly from +38.5, then jumps to −41.5 under the 60 kN load; the moment is largest at that point.
PositionShear (left / right, kN)Moment (kN·m)
A (0 m)0 / +38.50
Under 60 kN (5 m)+18.5 / −41.5142.5 (max)
B (8 m)−53.5 / 00
V5−=38.5−4×5=18.5 kNV_{5^-}=38.5-4\times5=18.5\text{ kN}V5+=18.5−60=−41.5 kNV_{5^+}=18.5-60=-41.5\text{ kN}VB=−41.5−4×3=−53.5 kNV_{B}=-41.5-4\times3=-53.5\text{ kN}M5=38.5×5−4×522=192.5−50=142.5 kN⋅mM_{5}=38.5\times5-\frac{4\times5^2}{2}=192.5-50=142.5\text{ kN·m}

Check: the shear at B, −53.5 kN, equals RBR_B with the opposite sign, and from the right M5=53.5×3−4×322=142.5M_5=53.5\times3-\tfrac{4\times3^2}{2}=142.5 — the two sides agree.

Concept map

Load path: from the weight of the slab to the shear and moment diagrams

Every calculation question starts on this route: area load → load per metre → reactions → shear → moment → compare with capacity. Where the maximum moment is, and how a reaction passes to the next member, are both on this map.

Text version (from cause to result)

  1. Cause

    Area load (kN/m²)

    The slab’s dead and imposed loads per square metre. For design they are factored: 1.4gk+1.6qk1.4g_k+1.6q_k.

  2. What changes itWhere marks are lost

    bb Tributary width

    The strip of slab whose load reaches a beam. With equal spacing ss: an interior beam takes s/2s/2 from each side, ss in total; an edge beam takes s/2s/2. Check the slab span direction first.

  3. Key idea

    ww Load per metre of beam

    Area load × tributary width gives the load along each metre of beam (kN/m), plus the beam’s self-weight.

    Area load × width → line load
  4. Key idea

    Free-body diagram: draw one beam on its own

    Replace the surroundings with support reactions. A pin stops movement but allows rotation; a roller gives one reaction at right angles to its surface; a lateral restraint is not a vertical support.

  5. Key ideaWhere marks are lost

    RAR_A, RBR_B Reactions: take moments

    Take moments about one support for the other reaction, then use vertical equilibrium. For overall equilibrium a UDL can be replaced by one force wLwL at its middle.

    Formula

    ∑MA=0∑Fy=0\textstyle\sum M_A=0\qquad\sum F_y=0
  6. Key idea

    VV Shear-force diagram

    Cut the beam anywhere: the sum of all forces left of the cut is the shear. It jumps at a point load and slopes under a UDL.

    Shear stops the two sides of a cut sliding
  7. Key ideaWhere marks are lost

    MM Bending-moment diagram

    Moments about the cut of all forces to its left. The change in moment = the area under the shear diagram: a parabola under a UDL, a sharp corner at a point load.

  8. ResultWhere marks are lost

    Shear changes sign → maximum moment

    Because the moment is the running area under the shear, it stops growing where the shear is zero (changes sign) — that is the maximum. Also check supports, load points and the root of any overhang.

  9. How design deals with itWhere marks are lost

    A reaction becomes the next member’s load

    A beam-end reaction pushes up on that beam and down, by the same amount, on the member below: slab → secondary beam → main beam → column → foundation.

  10. How design deals with it

    Demand ≤ capacity

    The largest shear and moment are the “demand”, compared with VcV_c and McM_c (or MbM_b for LTB). Worked numbers: floor-beam map.

  11. Exam answer

    Exam: label every value

    Label the shear on both sides of every load point and the moment at every load point and the maximum; show the RA+RBR_A+R_B check. The first 7 marks of the LTB question are here.

Tour steps

  1. 1. From area load to load per metre

    Area load × tributary width → load per metre (plus self-weight).

  2. 2. Draw one beam, find the reactions

    The free-body diagram shows only support reactions; take moments, then check the sum.

  3. 3. Shear and moment

    Shear = forces left of the cut; moment = area under the shear diagram.

  4. 4. The load keeps travelling down

    This beam’s reaction is the load the next member receives.

  5. 5. Check it and write it up

    Compare the largest VV and MM with the capacities; label every point on the diagrams.

4. Reading the section tables (Data File) Always examined

A size such as 457×152×52 UB means roughly 457 mm deep, 152 mm wide and 52 kg per metre. These are nominal sizes; read the real depth from the table (this beam is actually 449.8 mm deep).

SymbolMeaningUsed for
DDoverall depthshear area Av=tDA_v=tD
tt / TTweb thickness / flange thicknessTT decides the design strength pyp_y
b/Tb/T, d/td/tflange and web slenderness ratiosclassification (section 6)
IxI_x (cm⁴)second moment of area: stiffness against bendingdeflection
ZxZ_x (cm³)elastic section modulusthe 1.2pyZ1.2p_yZ cap; column buckling formulas
SxS_x (cm³)plastic section modulusmoment capacity pySp_yS
rx, ryr_x,\,r_y (cm)radius of gyrationslenderness λ=LE/r\lambda=L_E/r (buckling)
uu, xxbuckling parameter, torsional indexLTB calculation
AA (cm²)cross-section areacolumn capacity Pc=ApcP_c=Ap_c
Data File pageContents
p.1design strength pyp_y table; classification table (Table 7.1)
p.2beam, tension and compression formulas; deflection limits
p.3column interaction formulas; weld formulas
p.4bolt areas and strengths; bearing formulas
p.5Table 8.3a: LTB bending strength pbp_b
p.6Table 8.4: LTB equivalent moment factor mLTm_{LT}
p.7Table 8.7 strut-curve selection; Table 8.9 moment factor mm
p.8Table 8.8: compressive strength pcp_c
p.9–11UB and UC dimensions and properties
p.12unequal angles

5. Design strength pyp_y: grade and thickness Always examined

Thickness up toS275S355
16 mm275355
40 mm265345
63 mm255335
80 mm245325
100 mm235315

Example: a 610×229×140 UB has flange T=22.1 mmT=22.1\text{ mm}, thicker than 16 mm, so S355 gives py=345 N/mm2p_y=345\text{ N/mm}^2.

Quick check: What is pyp_y for a 12 mm S355 cover plate and a 20 mm S355 main plate?

Show answer

Cover plate 355 (12≤1612\le16); main plate 345 (16<20≤4016<20\le40).

6. Classification: will a thin plate crumple first? Always examined

ε=275py(py=355⇒ε=0.880;  py=345⇒ε=0.893)\varepsilon=\sqrt{\frac{275}{p_y}}\qquad(p_y=355\Rightarrow\varepsilon=0.880;\;p_y=345\Rightarrow\varepsilon=0.893)
Element (rolled I-section in bending)Class 1 plasticClass 2 compactClass 3 semi-compact
flange b/T≤b/T\le9ε9\varepsilon10ε10\varepsilon15ε15\varepsilon
web d/t≤d/t\le (bending)80ε80\varepsilon100ε100\varepsilon120ε120\varepsilon
  1. Work out ε\varepsilon

    Use the pyp_y chosen in section 5.

  2. Flange: compare b/Tb/T from the table with 9ε,10ε,15ε9\varepsilon,10\varepsilon,15\varepsilon

  3. Web: compare d/td/t with 80ε,100ε,120ε80\varepsilon,100\varepsilon,120\varepsilon

  4. Take the worse result (the higher class number)

    For example flange Class 2 and web Class 1 → the section is Class 2.

Understanding map

pyp_y and classification: one number used across the whole paper

pyp_y and the class look like a small opening step, but they flow into almost every capacity formula. Tap any box at the bottom to see what it relies on. The values are from 2024 Q1, beam B1 (356×127×39 UB, S355).

Text version (in working order)

  1. From the question

    S355\text{S355} Steel grade

    The question states S275 or S355. It is only the starting point for pyp_y, not pyp_y itself.

  2. From the tables

    TT Flange thickness

    The thickest part of the section (usually the flange of an I-section), used to read pyp_y.

    Where it comes from: Section table.

  3. Worked outWhere marks are lost

    pyp_y Design strength

    Thicker steel is slightly weaker. S355: T≤16T\le16 → 355; 16<T≤4016<T\le40 → 345.

    2024 Q1 (B1)

    T=10.7≤16  ⇒  py=355 N/mm2T=10.7\le16\;\Rightarrow\;p_y=355\text{ N/mm}^2
  4. From the tables

    b/Tb/T Flange ratio

    Flange outstand ÷ thickness. The smaller, the chunkier and the less likely to wrinkle.

    Where it comes from: Already worked out in the section table.

  5. From the tables

    d/td/t Web ratio

    Clear web depth ÷ web thickness.

    Where it comes from: Already worked out in the section table.

  6. Worked out

    ε\varepsilon Strength factor

    Adjusts the class limits to this pyp_y: the stronger the steel, the chunkier a plate must be to avoid wrinkling.

    Formula

    ε=275py\varepsilon=\sqrt{\frac{275}{p_y}}

    2024 Q1 (B1)

    275/355=0.880\sqrt{275/355}=0.880
  7. Worked out

    b/T≤9εb/T\le9\varepsilon Flange class

    Within 9ε9\varepsilon Class 1; within 10ε10\varepsilon Class 2; within 15ε15\varepsilon Class 3.

    2024 Q1 (B1)

    5.89<9×0.880=7.92  ⇒  Class 15.89<9\times0.880=7.92\;\Rightarrow\;\text{Class 1}
  8. Worked out

    d/t≤80εd/t\le80\varepsilon Web class

    Web in bending: within 80ε80\varepsilon Class 1; 100ε100\varepsilon Class 2; 120ε120\varepsilon Class 3.

    2024 Q1 (B1)

    47.2<80×0.880=70.4  ⇒  Class 147.2<80\times0.880=70.4\;\Rightarrow\;\text{Class 1}
  9. Worked outWhere marks are lost

    Class\text{Class} Section class

    Take the worse result (the higher number). E.g. flange Class 2, web Class 1 → Class 2.

  10. Worked out

    d/t≤70εd/t\le70\varepsilon Shear-buckling check

    Not part of the classification; if it holds, the web will not wrinkle in shear and the simple shear formula applies.

    2024 Q1 (B1)

    47.2<70×0.880=61.647.2<70\times0.880=61.6
  11. Capacity

    McM_c Moment capacity

    Class 1 or 2 → min⁡(pySx,1.2pyZx)\min(p_yS_x,1.2p_yZ_x); Class 3 → only pyZxp_yZ_x. Used in floor beams and columns.

    2024 Q1 (B1)

    min⁡ ⁣(355×6591000,  1.2×355×5761000)=233.95 kN⋅m\min\!\left(\frac{355\times659}{1000},\;\frac{1.2\times355\times576}{1000}\right)=233.95\text{ kN·m}
  12. Capacity

    VcV_c Shear capacity

    Uses pyp_y directly; the simple formula is allowed because d/t≤70εd/t\le70\varepsilon.

    Formula

    Vc=pyAv3×1000,  Av=tDV_c=\frac{p_yA_v}{\sqrt3\times1000},\;A_v=tD

    2024 Q1 (B1)

    355×2332.43×1000=478.06 kN\frac{355\times2332.4}{\sqrt3\times1000}=478.06\text{ kN}
  13. Capacity

    βw\beta_w Section factor for LTB

    Class 1 or 2 → βw=1\beta_w=1, so λLT=uvλ\lambda_{LT}=uv\lambda. Used in unrestrained beams (LTB).

  14. Capacity

    pbp_b, pcp_c Which column of the buckling tables

    Table 8.3a (pbp_b) and Table 8.8 (pcp_c) both have one column per pyp_y. A wrong pyp_y makes the whole buckling calculation wrong.

Tour steps

  1. 1. Copy three numbers

    The grade, the flange thickness TT, and the b/Tb/T and d/td/t already in the section table.

  2. 2. pyp_y depends on thickness

    10.7 mm ≤ 16 mm → 355.

  3. 3. ε\varepsilon adjusts the limits

    ε=275/py\varepsilon=\sqrt{275/p_y}; every class limit is a multiple of it.

  4. 4. Compare flange and web separately

    b/Tb/T against 9ε9\varepsilon, d/td/t against 80ε80\varepsilon.

  5. 5. Take the worse class

    Both Class 1 → the section is Class 1.

  6. 6. While you are here: shear buckling

    d/t≤70εd/t\le70\varepsilon → no shear-buckling check. Floor-beam answers usually state it too.

  7. 7. One pyp_y and one class, used everywhere

    The bottom row shows where they go: McM_c, VcV_c, the LTB βw\beta_w and the buckling-table columns.

Quick check: S355 (py=355p_y=355), b/T=8.5b/T=8.5, d/t=60d/t=60. Which class?

Show answer

9ε=7.929\varepsilon=7.92, 10ε=8.8010\varepsilon=8.80 → flange Class 2; 80ε=70.480\varepsilon=70.4 → web Class 1. Overall Class 2.

7. Interpolation: when your value falls between two table rows Always examined

y=y0+x−x0x1−x0 (y1−y0)y=y_0+\frac{x-x_0}{x_1-x_0}\,(y_1-y_0)

Example: λLT=64.70\lambda_{LT}=64.70; the table gives 60→25160\to251 and 65→23465\to234:

pb=251+64.70−6065−60×(234−251)=251+0.940×(−17)=235.0 N/mm2p_b=251+\frac{64.70-60}{65-60}\times(234-251)=251+0.940\times(-17)=235.0\text{ N/mm}^2

8. Deflection: does it sag too much? Always examined

δUDL=5wL4384EIδmidspan point load=PL348EIE=205 000 N/mm2\delta_{\text{UDL}}=\frac{5wL^4}{384EI}\qquad\delta_{\text{midspan point load}}=\frac{PL^3}{48EI}\qquad E=205\,000\text{ N/mm}^2

Example (2024 beam B1): imposed q=11.25 N/mmq=11.25\text{ N/mm}, L=7000 mmL=7000\text{ mm}, I=10 170×104 mm4I=10\,170\times10^4\text{ mm}^4:

δ=5×11.25×70004384×205 000×10 170×104=16.87 mm<7000360=19.44 mm  ⇒  OK\delta=\frac{5\times11.25\times7000^4}{384\times205\,000\times10\,170\times10^4}=16.87\text{ mm}<\frac{7000}{360}=19.44\text{ mm}\;\Rightarrow\;\text{OK}