STEELWORK / CON4334
Worked examples

Tutorial 4 Q1: compression resistance at a given effective length

Diagrams, explanations and answers are presented in reading order. No playback or response is required.
All answers shownChinese–English terminology
Diagrams, explanations and answers are presented in reading order. No playback or response is required.

Find the compressive resistance of 305×305×118 UC, Grade S355, with effective length 4.5m.

Original source: LectureNotes/Ch 4_Column.pdf — p. 40.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

Find which plate buckles first

Before using plastic bending resistance, check whether the flange and web can sustain the required stress distribution.

The short waves are local plate buckling. They differ from sideways movement of the whole member.
The short waves are local plate buckling. They differ from sideways movement of the whole member.

Prediction, then explanation. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Calculate the flange and web ratios separately. Compare each with the limits for its stress condition. The worse class governs.

ε=275/py\varepsilon=\sqrt{275/p_y}

py is the design yield strength in N/mm². ε is a dimensionless scale used in the supplied classification limits.

Scope. Pure bending and uniform compression use different web limits. Class 2 allows plastic resistance but not the Class 1 rotation capability.

Check and takeaway. A Class 1 web and Class 2 flange give a Class 2 section. Do not average the class numbers.

Vertical bending can trigger sideways motion

A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.

The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.
The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.

Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.

λ=LE/ry,Mb=pbSx  (Class 1/2),mLTMmax≤Mb\lambda=L_E/r_y,\qquad M_b=p_bS_x\;\text{(Class 1/2)},\qquad m_{LT}M_{max}\le M_b

LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.

Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.

Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.

A force couple carries moment

Separate the force couple used to carry moment from the force used to carry web shear.

The flange forces act in opposite directions. Their separation z gives the lever arm. The web arrow represents shear.
The flange forces act in opposite directions. Their separation z gives the lever arm. The web arrow represents shear.

Prediction, then explanation. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Moment is force multiplied by perpendicular separation. Divide the required moment by the specified separation to obtain each couple force.

F=M/zF=M/z

M is moment in kN·mm; z is the specified force-line separation in mm; F is force in kN.

Scope. Use the lever arm defined by the source model. Do not silently replace it with overall section depth or another geometric distance.

Check and takeaway. Check flange welds for the couple forces and web welds for the stated shear model. Both force paths need a satisfactory detail.

Apply the reasoning to this section’s data and conditions

Lookup: Data File p.11, exact row 305×305×118 UC.

Read the dimensions/local ratios table and the properties table separately.

The x–x axis crosses the web horizontally; y–y passes vertically through its centre in the table sketch.

PropertyValue and units
Flange/web/root-to-root web depthT=18.7mm、t=12mm、d=246.7mm。
Local slendernessbT=8.22、dt=20.6。
Radii (converted from cm)rx=13.6×10=136mm;ry=7.77×10=77.7mm。
AreaA=150cm2=15000mm2。
Elastic moduliZx=1760cm3;Zy=589cm3。
Plastic moduliSx=1958cm3;Sy=895cm3。
LTB parameters

u=0.85, x=16.2.

Both dimensionless

Why this method applies

Check buckling about both axes

Determine which buckling direction limits the compressed member.

Compare the outlines labelled Straight and Bowed. The dashed line beside Bowed marks its original straight reference.
Compare the outlines labelled Straight and Bowed. The dashed line beside Bowed marks its original straight reference.

Prediction, then explanation. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Calculate slenderness about each axis. Select each axis’s curve from section type and thickness. Then obtain and compare the two compressive resistances.

λx=LEx/rx,λy=LEy/ry,Pc=pcAg\lambda_x=L_{Ex}/r_x,\quad\lambda_y=L_{Ey}/r_y,\qquad P_c=p_cA_g

Effective lengths and radii use mm. pc is compressive strength in N/mm²; Ag is gross area in mm²; Pc is in N.

Scope. Do not select the governing axis using radius alone. Effective length and buckling curve can differ. A combined column also needs interaction checks.

Check and takeaway. A short-section yield resistance is not the same as long-member buckling resistance. Keep py and pc distinct.

Apply the reasoning to this section’s data and conditions

This is the same section as Column Example 1 but a shorter effective length.

Compare both axis resistances.

Because the task is pure compression, it only needs a non-slender local-section check before Agpc.

1. Local section and material strength

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A thin part can wrinkle first

A thin plate may wrinkle before the whole steel member reaches its intended resistance.

A thin part can wrinkle first — A thin plate may wrinkle before the whole steel member reaches its intended resistance.

Sketch, not to scale; use the original dimensions.

  1. Check flange and web slenderness using their own definitions.
  2. Compare each ratio with the correct class limits.
  3. The element with the more restrictive class determines the section class.

Remember: Bending limits and uniform-compression limits are different.

Related concept and full method

T=18.7mm; use the S355 thickness band to select py=345Nmm2. ε=275345=0.892805
Flange: bT=8.22<13ε=11.606470Web: dt=20.6<40ε=35.712215Non-slender under uniform compression, so gross area is permitted.

This proves Class 3 or better for axial design.

It is not a claim that plastic bending capacity has been established.

Mechanism detailsWhy thin elements buckle locally2 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. The flange outstand and web have different widths, thicknesses and edge support conditions.
  2. A thinner plate can wrinkle locally before the complete member loses stability.
  3. Class 1 allows plastic rotation.

    Class 2 reaches plastic resistance.

    Class 3 reaches elastic resistance.

    Class 4 requires effective properties.

  4. Check every relevant compression element with the supplied limits and stress distribution.

    The deformation shown is qualitative.

2. Both buckling axes and the answer

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Move between two known values

The required slenderness lies between two table rows. Estimate the strength on the straight segment between those rows.

xy(70, 200)(74, 192)(80, 180)70748040% of input interval → 40% of output change
The marked position lies partway along the horizontal interval. Use the same fraction of the vertical change.

Prediction, then explanation. If the second strength is lower, moving toward that row must reduce the interpolated strength.

Subtract the lower input to find distance travelled. Divide by the input interval. Multiply that fraction by the output change.

f=x−x0x1−x0,y=y0+f(y1−y0)f=\frac{x-x_0}{x_1-x_0},\qquad y=y_0+f(y_1-y_0)

x is the required input. The two known pairs are (x₀, y₀) and (x₁, y₁). f has no unit.

Scope. Use one table, curve and strength column. This interpolation does not permit extrapolation or inventing an intermediate steel section.

Check and takeaway. Illustration: between strengths 200 and 180, a fraction of 0.4 gives 192 N/mm². The result lies between both endpoints.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why a long column can fail before crushing

Push a long thin ruler from both ends: it may bow sideways first.

Why a long column can fail before crushing — Push a long thin ruler from both ends: it may bow sideways first.

Sketch, not to scale; use the original dimensions.

  1. Find effective length and radius of gyration for each axis.
  2. Calculate slenderness for both directions.
  3. Use the appropriate buckling curve before forming resistance.

Remember: Compare the final resistances; slenderness alone may not identify the controlling axis.

Related concept and full method

Table 8.7: hot-rolled H-section (UC), maximum thickness ≤40mm, about the x axis use curve b, about the y axis use curve c.

Use the Data File p.8 py=345Nmm2 column.

The two axes use different curves, so slenderness alone cannot identify the governing axis.

LEx=LEy=4500mm is the given effective length.λx=4500136=33.088235λy=450077.7=57.915058x axis, curve b: 30 row gives 325; 35 row gives 318Nmm2. Interpolation fraction: 33.088235−3035−30=0.617647pc=325+0.617647×(318−325)=320.676471Nmm2y axis, curve c: 56 row gives 252; 58 row gives 247Nmm2. Interpolation fraction: 57.915058−5658−56=0.957529pc=252+0.957529×(247−252)=247.212355Nmm2Pcx=Apcx10=150×320.67647110=4810.147059kNPcy=150×247.21235510=3708.185328kNPc=min(Pcx,Pcy)=3708.185328kN
Pc=3708.185328kN.

The weak axis controls.

No applied axial force is supplied in Q1.

Therefore, the answer is a resistance, not an adequacy statement for an invented load.

This is lower than the squash resistance 5,175kN because member buckling reduces the usable strength.

Mechanism detailsEffective length and buckling axes3 concepts · 4 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.

Lecturer's answer

ItemLecturer's value
305×305×118 UCT=18.7>16⇒py=345T=18.7>16\Rightarrow p_y=345, the section is not slender
Slenderness and strengthλy=4500/77.7=57.9\lambda_y=4500/77.7=57.9, pc=247 N/mm2p_c=247\text{ N/mm}^2
Compression resistancePc=150×102×247=3705 kNP_c=150\times10^2\times247=3705\text{ kN}

Conclusion: Pc=3705 kNP_c=3705\text{ kN}.

Source: Lecturer's tutorial solution, Ch 4, p. 1.

Result and concise exam wording

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the property for the physical question

A section table contains several numbers. Choose the property that matches the calculation and bending axis.

Read the three labels beside the I-section: I describes geometric stiffness, Z elastic section modulus and S plastic section modulus.
Read the three labels beside the I-section: I describes geometric stiffness, Z elastic section modulus and S plastic section modulus.

Prediction, then explanation. Moving equal area away from an axis increases I about that axis. It does not increase total area.

Each small area contributes its area multiplied by squared distance. Sum those contributions to obtain I.

I=∫y2 dA,r=I/AI=\int y^2\,dA,\qquad r=\sqrt{I/A}

I is second moment of area in mm⁴. y is distance from the chosen axis in mm. A is area in mm². r is radius of gyration in mm.

Scope. Z is elastic section modulus; S is plastic section modulus in this course. Neither is interchangeable with I.

Check and takeaway. A nominal section designation is a row identifier. Use the actual dimensions and units in that exact row.

Apply the reasoning to this section’s data and conditions

T=18.7mm, giving py=345.

bT=8.22<13ε; dt=20.6<40ε.

λx=4,500136=33.088235; λy=4,50077.7=57.915058.

The hot-rolled H-section uses curves b/c respectively.Pcx=4810.147kN; Pcy=3708.185kN; compression resistance Pc=3708.185kN.

Misconceptions and checks

Compression acts on the displaced shape

A compressed member moves away from its initial load line. Explain why the bending moment can increase.

The dashed line labelled Original marks the initial position. The tilted member creates the extra horizontal lever arm shown below.
The dashed line labelled Original marks the initial position. The tilted member creates the extra horizontal lever arm shown below.

Prediction, then explanation. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Force acting through an offset forms a moment. Second-order analysis includes that changed geometry in equilibrium.

Madditional=PΔorPδM_{additional}=P\Delta\quad\text{or}\quad P\delta

P is axial force. Δ and δ are the relevant perpendicular displacements. Consistent force and length units give moment units.

Scope. Use the amplification or analysis method stated for the frame. Do not amplify an already amplified moment a second time.

Check and takeaway. Zero offset removes this additional moment in the ideal sketch. Real design may still require imperfections and code checks.

Use the same mechanism: Use the property for the physical question. Moving equal area away from an axis increases I about that axis. It does not increase total area.

Apply the reasoning to this section’s data and conditions

  • Do not use 355Nmm2 for a flange thicker than 16mm.
  • Do not substitute plastic moduli in the member elastic denominators.
  • Do not amplify an already amplified Mᴸᵀ twice.
  • Do not treat an axial resistance pass as proof of combined-load adequacy.

How the method transfers to a new variant

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

  1. Identify construction type, axis, actual length and effective length.
  2. Read thickness, grade and the exact UC row.

    Classify before using plastic moduli.

  3. Sum vertical forces and derive signed eccentric moments; share moments only when the joint has two columns.
  4. Apply specified amplification once.

    Check the capped section interaction.

  5. Select curves b/c for these rolled H sections, interpolate both strengths and check flexural interaction with elastic moduli.
  6. Use the appropriate simple/continuous LTB slenderness rule and the course first-order minor-axis term.
  7. Report every utilisation and let any failed check govern.

Prediction with explained answer

A strong cross-section can belong to an unstable member

A column carries axial compression and bending. Explain why more than one check is required.

The three boxes name separate checks: Section, Flexural and LTB. The bottom caption explains that passing one does not pass the others.
The three boxes name separate checks: Section, Flexural and LTB. The bottom caption explains that passing one does not pass the others.

Prediction, then explanation. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Separate cross-section, flexural-buckling and LTB interaction equations. Use each equation’s own denominators and first-order or amplified moments.

AgpyA_g p_y is a section axial resistance. AgpcA_g p_c is a member compression resistance. Elastic pyZp_y Z and prescribed McM_c are different bending denominators.

Scope. Preserve the course barred-moment definitions and Eq. 8.81 convention. Do not substitute plastic moduli into an elastic denominator.

Check and takeaway. Report each requested utilisation and the governing check. The largest properly calculated ratio identifies the closest limit.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Invented variant: can the same column carry 4,000kN in pure compression?

Answer and reasoning

No. FPc=4,0003708.185328=1.078695>1.

The gross squash resistance is not the member resistance.

Mechanism detailsEffective length and buckling axes1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A column can bow sideways before its section reaches the crushing resistance.
  2. Each axis has its own radius of gyration and restraint spacing.
  3. , with compatible length units.

    A tie affects only the directions it actually restrains.

  4. Select each buckling curve and compressive strength before forming Pc.

    The governing axis is determined by resistance, not slenderness alone.