STEELWORK / CON4334
Worked examples

Connection example 3: an eccentric bolt group in the plate plane

Diagrams, explanations and answers are presented in reading order. No playback or response is required.

← Read this lecture example beside its chapter concepts

All answers shownChinese–English terminology
Diagrams, explanations and answers are presented in reading order. No playback or response is required.

Check the Grade 8.8 M24 bolt group carrying 100kN dead plus 130kN imposed load at a 525mm eccentricity. Steel is S355. Use the lecturer’s one-side-plate load model.

Original source: LectureNotes/Ch 2_Connection.pdf — p. 25, p. 26.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

Add force components at each bolt

An in-plane load acts away from the bolt-group centre. Find the largest resultant bolt force.

The direct-force arrows are parallel. The moment-force arrows run tangentially around the bolt-group centre.
The direct-force arrows are parallel. The moment-force arrows run tangentially around the bolt-group centre.

Prediction, then explanation. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Locate the bolt-group centre and coordinates. Add horizontal components together and vertical components together before finding each resultant.

M=Pe,J=∑(xi2+yi2),FMx=−Myi/J,FMy=Mxi/JM=Pe,\quad J=\sum(x_i^2+y_i^2),\quad F_{Mx}=-My_i/J,\quad F_{My}=Mx_i/J

e, xi and yi use mm; J uses mm². With M in kN·mm, each moment-force component is in kN.

Scope. These expressions use the stated elastic, equal-bolt in-plane model. Out-of-plane tension and prying require another model.

Check and takeaway. Do not add force magnitudes before resolving directions. Two perpendicular forces of 3 and 4 kN give 5 kN, not 7 kN.

A bolt diameter is not a hole diameter

Check that bolts fit and leave enough material between holes and plate boundaries.

pdd₀Clear ligament
The inner circle represents bolt diameter d. The outer circle represents hole diameter d₀. Pitch and gauge join hole centres.

Prediction, then explanation. At fixed pitch, a larger hole leaves a shorter clear ligament. Increasing bolt diameter may also increase minimum edge-distance requirements.

Measure pitch along the bolt line and gauge across lines. Distinguish end distance along the load from edge distance across it.

lc=p−d0l_c=p-d_0

lc is clear ligament between holes; p is centre-to-centre pitch; d₀ is hole diameter. All use mm.

Scope. Apply the supplied edge-preparation and minimum/maximum spacing rules. Passing a bearing calculation does not prove the layout passes.

Check and takeaway. For pitch 60 mm and hole diameter 22 mm, the ligament is 38 mm. Using a 20 mm bolt diameter here gives the wrong ligament.

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Apply the reasoning to this section’s data and conditions

InputOrigin
Given load/model

100kN dead+130kN imposed.

Drawing says bolt loads shown on one plate.

Do not halve the specified force again.

Given e525mm horizontal distance from the dashed bolt-group centreline to vertical load line, upper dimension.
Coordinates

x=±250mm from the two 250 dimensions.

y=±35,±105,±175mm from 70mm pitch and symmetric six-row arrangement.

Thickness and edge

Side plate 15mm; p.26 gives UC flange 17.3mm, so tp=15.

Vertical end 45mm; pitch 70; hole 26mm.

LookupM24 As=353mm2; ps=375,pbb=1,000,pbs=550,Us=510,Ub=800Nmm2.

Why this method applies

Use the same mechanism: Add force components at each bolt. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Test every possible fracture cut

Find the remaining steel area across a candidate tension-failure path.

The dashed fracture line crosses two hole centres. Subtract only the holes crossed by that candidate line.
The dashed fracture line crosses two hole centres. Subtract only the holes crossed by that candidate line.

Prediction, then explanation. At fixed plate size, larger holes reduce the straight-path net area. A diagonal path needs its own stagger correction.

Subtract the hole widths crossed by the path, then multiply by thickness. Compare all plausible paths using the applicable course rule.

An=(b−nd0)tA_n=(b-nd_0)t

An is net area in mm²; b is plate width; d₀ is hole diameter; t is thickness, all in mm. n counts holes on this straight path.

Scope. This expression is for a straight cut. Effective area can require further shear-lag rules. Gross, net and effective areas must remain distinct.

Check and takeaway. Use the hole diameter, not the bolt diameter, when removing missing steel. The plate contains a hole, not solid steel around the bolt shank.

Apply the reasoning to this section’s data and conditions

The load rotates the plate in its own plane.

Therefore, each bolt takes uniform direct shear plus tangential torsional shear.

This is not a bolt-tension problem.

Use centroidal coordinates, sum squared distances over all 12 bolts, and resolve torsional force into components before adding direct shear.

The far right corners have torsional vertical force in the same direction as direct shear.

1. Factored load and moment

Keep load categories separate

A floor carries permanent material and changing occupancy loads. Find the design load for the stated check.

The two boxes show G and Q with their separate factors. The plus sign joins their factored values.
The two boxes show G and Q with their separate factors. The plus sign joins their factored values.

Prediction, then explanation. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

First convert mass to weight where required. Next collect G and Q in compatible units. Apply the combination specified by the course problem.

Wu=1.4G+1.6QW_u=1.4G+1.6Q

G is characteristic dead load; Q is characteristic imposed load. Wu is the design load for this course gravity combination.

Scope. This combination is not universal. Use the specified service load for deflection and the stated factors for other standards or cases.

Check and takeaway. Illustration: G = 10 kN and Q = 5 kN give 22 kN. Factoring their sum by one guessed factor loses the distinction.

Use the same mechanism: Add force components at each bolt. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Apply the reasoning to this section’s data and conditions

P=1.4×100+1.6×130=140+208=348kNM=Pe=348kN×525mm=182,700kN·mm=182.7kN·m

Mechanism detailsFrom characteristic to design load2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. G is permanent load; Q is imposed load.

    A surface load and a line load also have different units.

  2. This illustration uses the course gravity case .

    Other combinations in the original text retain their own factors.

  3. For illustrative , the separate load contributions show what changes when Q increases.
  4. Do not carry this ULS total automatically into deflection.

    Follow the stated SLS load case.

2. Bolt-group polar sum and corner radius

Use the same mechanism: Add force components at each bolt. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Apply the reasoning to this section’s data and conditions

Physical interpretation: An off-centre force also tries to turn the group

Pulling away from the centre causes a push plus a twist.

An off-centre force also tries to turn the group — Pulling away from the centre causes a push plus a twist.

Sketch, not to scale; use the original dimensions.

  1. Find direct shear and moment about the bolt-group centroid.
  2. Moment-induced forces act tangentially; farther bolts attract more.
  3. Add horizontal and vertical components before finding the resultant.

Remember: Do not simply add two force magnitudes pointing in different directions.

Related concept and full method

Each bolt contributes x2+y2.

There are 12 identical |x| values.

At each absolute height 35, 105, 175mm there are four bolts: two left/right positions multiplied by two positive/negative vertical positions.

Σx2=12×2502=12×62,500=750,000mm2Σy2=4(352+1052+1752)=4(1,225+11,025+30,625)=171,500mm2J=750,000+171,500=921,500mm2rA=2502+1752=93,125=305.164mmcosφ=250305.164=0.819232

Mechanism detailsAdd direct and torsional bolt forces1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Assign signed coordinates to the bolts relative to the group centroid.
  2. For the equal-bolt elastic model, the direct force is per bolt.
  3. Moment magnitude is .

    Its sign follows the load direction.

    For signed M: , , .

  4. Add signed x and y components at each bolt, then take the resultant.

    The longest arrow shows the critical bolt in this illustration.

3. Direct force, torsion and maximum resultant

Use the same mechanism: Add force components at each bolt. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Add arrows before taking the magnitude

Walking east and walking north do not point in the same direction.

Add arrows before taking the magnitude — Walking east and walking north do not point in the same direction.

Sketch, not to scale; use the original dimensions.

  1. Choose signed horizontal and vertical directions.
  2. Add contributions along each direction separately.
  3. For perpendicular components, use the right-triangle resultant.

Remember: Check the corner where direct and torsional components reinforce each other.

Related concept and full method

Direct shear per bolt: Fs=P12=34812=29kNFT,A=MrJ=182,700×305.164921,500=60.503kNVertical torsional-force component: M×250J=49.566kNHorizontal torsional-force component: M×175J=34.696kNFR,A=(29+49.566)2+34.6962=85.886kN

The units of MrJ are (kN·mm)×mmmm2=kN.

The top/bottom right corners have equal resultant magnitude.

Other rows have a smaller horizontal torsion component.

The left column’s vertical torsion subtracts from direct shear, so it is less critical.

Mechanism detailsAdd direct and torsional bolt forces1 concept · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Assign signed coordinates to the bolts relative to the group centroid.
  2. For the equal-bolt elastic model, the direct force is per bolt.
  3. Moment magnitude is .

    Its sign follows the load direction.

    For signed M: , , .

  4. Add signed x and y components at each bolt, then take the resultant.

    The longest arrow shows the critical bolt in this illustration.

4. Compare with single-shear bolt resistance

Count cuts through each loaded bolt

Find how many shear planes transfer the force through one side of the connection.

The middle plate moves against two cover plates. The two interfaces cut each bolt at two planes.
The middle plate moves against two cover plates. The two interfaces cut each bolt at two planes.

Prediction, then explanation. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Select the area at the actual shear plane. Multiply by bolt shear strength. Count only the bolts and planes in the same transfer stage.

Ps=psAs,Pgroup=nbnsPsP_s=p_sA_s,\qquad P_{group}=n_b n_s P_s

ps is bolt shear strength in N/mm²; As is the appropriate area in mm². nb counts bolts; ns counts equally loaded shear planes.

Scope. Use the thread area when threads cross the plane as required. Check bearing, plate failure and detailing separately.

Check and takeaway. Both halves of a butt splice carry the full transmitted force in sequence. Counting both halves together would double the apparent resistance.

Apply the reasoning to this section’s data and conditions

Ps=375×3531,000=132.375kN>85.886kNPasses.

The source checks the side plate’s single shear interface.

The plan view showing plates on both sides does not authorise doubling resistance while keeping only one side’s force model.

Mechanism detailsCount the bolt shear planes1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Load must cross an interface between the connected plates.
  2. A lap joint gives one shear plane through a bolt.
  3. A symmetric double-cover joint may provide two shear planes.

    Count load-transfer interfaces, not just visible plates.

  4. Use the source’s area and shear strength.

    Then check bearing, plate resistance and detailing separately.

5. Check bolt bearing against the same resultant

Follow contact pressure into the plate

The bolt may survive shear while the connected plate deforms or tears near the hole.

The labels distinguish bolt diameter d from hole diameter d₀. The arrow at the hole edge shows the bearing contact action.
The labels distinguish bolt diameter d from hole diameter d₀. The arrow at the hole edge shows the bearing contact action.

Prediction, then explanation. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

Calculate every bound required by the supplied rule. The smallest applicable bound limits the connection at that layer.

Pbearing≤pbsdtP_{bearing}\le p_{bs}dt

pbs is the applicable bearing strength in N/mm²; d is nominal bolt diameter in mm; t is plate thickness in mm.

Scope. This diameter term alone is not the complete check. End-distance and clear-ligament limits, bolt bearing and each connected layer also matter.

Check and takeaway. Two covers and one main plate do not necessarily have the same thickness or strength. Compare the actual force share in each layer.

Apply the reasoning to this section’s data and conditions

tp=min(15,17.3)=15mmPbb=24×15×1,0001,000=360kN>85.886kNPasses.

Mechanism detailsBearing and the remaining ligament1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Force transfers through contact between bolt and connected plate.
  2. The plate around the hole carries bearing stress.

    Bolt bearing and plate bearing are separate checks.

  3. A short ligament can tear out towards the end.

    The direction of force determines the relevant edge.

  4. Evaluate every specified bearing and ligament bound for each layer and retain the smallest applicable resistance.

6. Connected-part bounds and conclusion

Use the same mechanism: Follow contact pressure into the plate. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

Use the same mechanism: Add force components at each bolt. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Apply the reasoning to this section’s data and conditions

Physical interpretation: The bolt can crush or tear the plate

A strong bolt can still push through a weak hole edge.

The bolt can crush or tear the plate — A strong bolt can still push through a weak hole edge.

Sketch, not to scale; use the original dimensions.

  1. Check the bolt and each connected plate’s bearing bounds.
  2. Use nominal bolt diameter for bearing; hole size for removed material.
  3. The smallest applicable resistance controls.

Remember: A short end distance may govern even when bolt shear passes.

Related concept and full method

lc=70−26=44mmB1=1×24×15×5501,000=198kNB2=0.5×1×45×15×5501,000=185.625kNNet-clearance term between holes: 1.5×44×15×5101,000=504.9kNUpper cap: 2×24×15×8001,000=576kNPbs=min(198,185.625,504.9,576)=185.625kN>85.886Passes.

For the course’s specified connection checks, single-shear bolt capacity 132.375kN is the governing resistance per critical bolt.

The ratio 85.886132.375≈0.649.

This is not a total connection force capacity of 132.375kN: it is compared with the critical bolt force.

Mechanism detailsBearing and the remaining ligament2 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Force transfers through contact between bolt and connected plate.
  2. The plate around the hole carries bearing stress.

    Bolt bearing and plate bearing are separate checks.

  3. A short ligament can tear out towards the end.

    The direction of force determines the relevant edge.

  4. Evaluate every specified bearing and ligament bound for each layer and retain the smallest applicable resistance.

Result and concise exam wording

Use the same mechanism: Follow contact pressure into the plate. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

Apply the reasoning to this section’s data and conditions

P=348kN, M=182.7kN·m.

J=921,500mm2; r=305.164mm.

Fs=29kN, FT=60.503kN; FR,max=85.886kN.

Per-bolt resistances: shear 132.375kN, bolt bearing 360kN, plate bearing 185.625kN.

All exceed the resultant; requested checks pass.

Misconceptions and checks

Treat a weld group as lines

An eccentric force creates direct line force and torsional line force in the same weld group.

The four perimeter lines represent weld runs. The interior label says No weld here: the enclosed plate area is not weld length.
The four perimeter lines represent weld runs. The interior label says No weld here: the enclosed plate area is not weld length.

Prediction, then explanation. Increasing eccentricity increases the torsional contribution. The governing corner depends on vector addition, not distance alone.

Find the line centroid. Integrate squared distance along the effective lines. Add direct and torsional components at every candidate critical point.

J=∫r2 dl,qMx=−My/J,qMy=Mx/JJ=\int r^2\,dl,\qquad q_{Mx}=-My/J,\quad q_{My}=Mx/J

J is line polar inertia in mm³. x and y use mm. With M in kN·mm, q is line force in kN/mm.

Scope. A solid rectangle has area inertia in mm⁴ and is not this weld-line model. Missing weld sides change the centroid and integrals.

Check and takeaway. Compare the largest resultant line force with the selected throat resistance. Keep kN/mm distinct from total force in kN.

Use the same mechanism: Add force components at each bolt. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Change the ruler, keep the quantity

A section table uses centimetres, but the strength calculation uses millimetres. The numbers must describe the same section.

Length1 factorArea2 factors3 factorsEach centimetre becomes ten millimetres.
In the diagram, the length, square and cube contain one, two and three length factors. Each factor changes when the ruler changes.

Prediction, then explanation. Would every property increase by ten? No. The exponent determines how many factors of ten are needed.

First identify the physical quantity. Next convert each length factor. Keep force and length conversions separate when converting a moment.

1 cmn=10n mmn,1 kN m=106 N mm1\,\mathrm{cm}^n=10^n\,\mathrm{mm}^n,\qquad 1\,\mathrm{kN\,m}=10^6\,\mathrm{N\,mm}

Here n is the length exponent: 2 for area, 3 for section modulus and 4 for second moment of area.

Scope. Changing units changes neither the load nor the section. A conversion factor cannot repair a formula for the wrong physical quantity.

Check and takeaway. Illustration: 2 cm4=20,000 mm42\,\mathrm{cm}^4=20{,}000\,\mathrm{mm}^4. The fourth power belongs to the unit, not the number 2.

Apply the reasoning to this section’s data and conditions

  • Do not use P12 as the complete bolt demand.
  • The sum for bolt-group geometry has units mm2, unlike weld line inertia mm3.
  • The 525mm eccentricity starts at the group centroid, not the right bolt column.
  • Add force components.

    Fs+FT is not the actual resultant.

How the method transfers to a new variant

Use the same mechanism: Add force components at each bolt. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Use the same mechanism: Keep load categories separate. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

Apply the reasoning to this section’s data and conditions

  1. Locate centroid and write every bolt coordinate.
  2. Compute factored P, centroidal eccentricity e and M.
  3. Sum all r2 and resolve MrJ into components.
  4. Find the corner where torsion adds to direct shear.
  5. Compare that resultant with shear and all bearing limits.

Prediction with explained answer

Use the same mechanism: Add force components at each bolt. At fixed force, increasing eccentricity increases the moment component. Its direction differs between bolts.

Use the same mechanism: Keep load categories separate. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

If both characteristic loads increase by 20% with unchanged geometry, how does the critical bolt force change?

Answer and reasoning

P and M each multiply by 1.2; every direct/torsional component does too.

FR=1.2×85.886=103.063kN, still below 132.375kN.

Capacity is unchanged.

Mechanism detailsAdd direct and torsional bolt forces1 concept · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Assign signed coordinates to the bolts relative to the group centroid.
  2. For the equal-bolt elastic model, the direct force is per bolt.
  3. Moment magnitude is .

    Its sign follows the load direction.

    For signed M: , , .

  4. Add signed x and y components at each bolt, then take the resultant.

    The longest arrow shows the critical bolt in this illustration.