Assignment 2 Q3: classification, protection, built-up sections and second-order analysis
Answer all four theory parts: describe the four section classes; sketch two UB fire-protection methods; identify two built-up sections with sketches; and explain the HK2011 second-order elastic / method with a sketch.
Original source: Assignment/AY2627s 1-CON4334-Assignment 2.pdf — p. 2.
A given value comes from the question or diagram.
A lookup value comes from the named table.
A calculated value follows from the working.
Each assumption is stated where the calculation needs it.
Known information, diagram labels and unknowns
A table value has conditions
Find a design property without mixing a row, column or standard from a different case.
Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.
Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.
Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.
Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.
Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.
Apply the reasoning to this section’s data and conditions
Given scope: the four requested theory topics and the HK Steel Code 2011 course basis.
There are no design temperatures, fire durations, loads, stiffnesses or numerical displacements to calculate.
The answer should identify mechanisms and label sketches without inventing product thicknesses or ratings.
Why this method applies
Delay heat reaching the steel
Identify how the protection surrounds a steel section. Then explain its purpose in a fire.
Prediction, then explanation. An insulating layer can slow heating. It does not mean the steel remains at room temperature indefinitely.
Heat changes steel behaviour. Protection delays that change by restricting heat transfer. Show the steel and protection boundaries separately.
The labelled boundaries describe geometry. They do not specify a tested fire-resistance rating.
Scope. Required thickness depends on the system, member and required rating. Do not infer thickness or minutes from a schematic.
Check and takeaway. For a sketch answer, distinguish all three shapes and state that protection delays steel heating.
Compression acts on the displaced shape
A compressed member moves away from its initial load line. Explain why the bending moment can increase.
Prediction, then explanation. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.
Force acting through an offset forms a moment. Second-order analysis includes that changed geometry in equilibrium.
P is axial force. Δ and δ are the relevant perpendicular displacements. Consistent force and length units give moment units.
Scope. Use the amplification or analysis method stated for the frame. Do not amplify an already amplified moment a second time.
Check and takeaway. Zero offset removes this additional moment in the ideal sketch. Real design may still require imperfections and code checks.
A safe beam can still sag too far
Check whether the beam displacement exceeds the permitted service limit.
Prediction, then explanation. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.
Load bends each beam segment. The curvature accumulates along the span. Material stiffness E and geometric stiffness I resist that deformation.
Use w in N/mm, L in mm, E in N/mm² and I in mm⁴. The resulting midspan deflection is in mm.
Scope. The formula assumes a prismatic, simply supported, linear-elastic beam with full-span UDL. Use the stated service load and deflection limit.
Check and takeaway. A higher yield grade does not automatically increase E. Passing a strength check therefore does not prove acceptable deflection.
Apply the reasoning to this section’s data and conditions
For each theory term, explain the physical mechanism.
Then state its design consequence.
Each sketch should show the feature being explained.
Show class rotation ability, a protection barrier, or the plates of a built-up section.
For second-order effects, distinguish the two displacement types.
The source fire figure names three shapes: Solid Casing, Hollow Casing and Profile Casing.
The board and sprayed examples illustrate materials for the hollow and profile shapes.
Those material labels are teaching annotations.
They are absent from the source drawing.
(a) Describe Classes 1–4
Find which plate buckles first
Before using plastic bending resistance, check whether the flange and web can sustain the required stress distribution.
Prediction, then explanation. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.
Calculate the flange and web ratios separately. Compare each with the limits for its stress condition. The worse class governs.
py is the design yield strength in N/mm². ε is a dimensionless scale used in the supplied classification limits.
Scope. Pure bending and uniform compression use different web limits. Class 2 allows plastic resistance but not the Class 1 rotation capability.
Check and takeaway. A Class 1 web and Class 2 flange give a Class 2 section. Do not average the class numbers.
Apply the reasoning to this section’s data and conditions
Physical interpretation: A thin part can wrinkle first
A thin plate may wrinkle before the whole steel member reaches its intended resistance.
Sketch, not to scale; use the original dimensions.
- Check flange and web slenderness using their own definitions.
- Compare each ratio with the correct class limits.
- The element with the more restrictive class determines the section class.
Remember: Bending limits and uniform-compression limits are different.
| Class | What happens in bending | Key phrase for an exam answer |
|---|---|---|
| 1 plastic | The section reaches full plastic resistance and can undergo sufficient plastic rotation before local buckling. | Plastic moment and plastic-hinge rotation capacity. |
| 2 compact | The section reaches plastic resistance but has insufficient rotation capacity for a fully developed plastic hinge/redistribution assumption. | Plastic moment, limited rotation. |
| 3 semi-compact | An extreme fibre reaches yield; local buckling prevents full plastic stress redistribution. | Elastic first-yield resistance pᵧZ. |
| 4 slender | Local buckling occurs before gross-section yield resistance is reached. | Effective section/local-buckling treatment needed. |
The least favourable relevant compression element governs the overall class.
Classification depends on width/thickness ratio, material strength throughε and stress pattern.
It is independent of whether the whole member can undergo lateral-torsional buckling.
Classes 1/2 use the course capped plastic expression min(pᵧS,1.2pᵧZ).
Do not erase the ceiling.
Mechanism detailsWhy thin elements buckle locally
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- The flange outstand and web have different widths, thicknesses and edge support conditions.
- A thinner plate can wrinkle locally before the complete member loses stability.
Class 1 allows plastic rotation.
Class 2 reaches plastic resistance.
Class 3 reaches elastic resistance.
Class 4 requires effective properties.
Check every relevant compression element with the supplied limits and stress distribution.
The deformation shown is qualitative.
(b) Sketch two fire-protection methods
Use the same mechanism: Delay heat reaching the steel. An insulating layer can slow heating. It does not mean the steel remains at room temperature indefinitely.
Apply the reasoning to this section’s data and conditions

Original fire-protection sections, Ch 1 p.3.
Identify the layer around the UB.
From left to right: Solid Casing, Hollow Casing and Profile Casing.
The middle sketch has a gap between the rectangular enclosure and the steel section.
The right-hand protection closely follows the exposed I-section profile.Open full-size image
| Method to sketch | Labels and explanation |
|---|---|
| Board encasement | Draw the steel I section inside a rectangular board casing. Label UB, fire-resistant boards, board joints/fixings and the enclosed space. The casing delays heat reaching the steel. |
| Sprayed protection | Draw a layer following the exposed I-profile: flange tops/undersides, web faces and flange edges. Label UB and sprayed insulating fire-protection layer. It delays the steel temperature rise over exposed surfaces. |
Explain why protection is needed: elevated temperature reduces steel strength and stiffness, so a normally adequate member may lose load resistance or stability.
A sketch of an unlabelled rectangle alone does not distinguish a board system from concrete encasement.
No required rating, tested system or thickness is supplied.
Do not assign a fictitious coating thickness or “two-hour” rating.
Mechanism detailsSee the fire-protection enclosure
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
Steel loses strength as it heats.
Protection aims to delay heat reaching the section.
- Solid casing fills the enclosure around the I-section.
- A hollow enclosure surrounds the section while leaving an air space.
Profile casing follows the section outline.
The supplied sketch does not determine protection thickness or fire duration.
(c) Sketch and identify two built-up sections
Use the property for the physical question
A section table contains several numbers. Choose the property that matches the calculation and bending axis.
Prediction, then explanation. Moving equal area away from an axis increases I about that axis. It does not increase total area.
Each small area contributes its area multiplied by squared distance. Sum those contributions to obtain I.
I is second moment of area in mm⁴. y is distance from the chosen axis in mm. A is area in mm². r is radius of gyration in mm.
Scope. Z is elastic section modulus; S is plastic section modulus in this course. Neither is interchangeable with I.
Check and takeaway. A nominal section designation is a row identifier. Use the actual dimensions and units in that exact row.
Apply the reasoning to this section’s data and conditions

Original built-up section examples, Ch 1 p.5: different steel plates or components form a single section.
From left to right: Plate Girder, Built-up Column, Box Girder and Box Column.
Fine lines distinguish the component plates.
No fabrication dimensions are supplied.Open full-size image
| Section | What the sketch must show |
|---|---|
| Welded I section / plate girder | One vertical web plate between two horizontal flange plates. Mark longitudinal welds joining the web to each flange. Label each plate separately. The assembled I is not a single hot-rolled product. |
| Welded box section | Four plate walls forming a closed rectangle, with corner longitudinal welds. Label top/bottom flange plates and the two side webs; show the hollow interior. |
A built-up section is fabricated by joining components to obtain a required form or size.
In the I section, flanges principally provide bending resistance and the web mainly carries shear; in the box, the closed shape also supplies torsional stiffness.
These are qualitative functions, not a substitute for strength/buckling checks.
A hot-rolled UB drawn without component boundaries or welds does not illustrate a built-up section.
Mechanism detailsExplore section geometry and axes
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
The flanges are the wide plates.
The web connects them.
Rotate the I-section to see both.
- The same section has different stiffness and resistance about its two principal axes.
I controls elastic curvature.
is elastic section modulus.
Plastic modulus S comes from plastic stress blocks.
Nominal section labels are not every actual dimension.
Keep the row, axis and units together.
(d) Second-order elastic and analysis
Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.
Apply the reasoning to this section’s data and conditions
Physical interpretation: Moving sideways gives the load a new lever arm
Once a compressed member moves sideways, the same compression creates extra moment.
Sketch, not to scale; use the original dimensions.
- P–Δ concerns overall frame or storey movement.
- P–δ concerns bowing relative to the member’s end line.
- Amplify only the first-order moments specified by the method.
Remember: Do not amplify a moment that the question already gives as amplified.

Ch 1 p.11: sway and member bending in a frame under compression.
Dashed/curved lines represent deformation, not additional supports.
is the compressive force.
is overall sway.
is local member-bending displacement.
is the column height shown.
is the effective length shown (the original uses a lower-case subscript ).
Neither displacement is an angle.Open full-size image
Draw the original straight frame in a light line and the displaced frame in a stronger line.
Mark a compression loadP at the top, global horizontal storey displacementΔ and local bowδ relative to the displaced member chord.
andδ are lengths, not angles or two names for the same movement.
- Apply the specified loads to an elastic structural model with the relevant initial frame/member imperfections.
- Recognise that equilibrium must be satisfied on the displaced geometry: axial forces acting throughΔ andδ create additional moments.
- Include global sway and local member-curvature effects by second-order analysis, or the course’s permitted equivalent amplification approach within its applicable frame classification.
- Recheck member strength and stability using the resulting design actions; “elastic” describes the material analysis, not a promise that geometry effects are negligible.
The course distinguishes non-sway, sway and ultra-sensitive frames using elastic critical-load sensitivity.
An ultra-sensitive frame cannot be justified by simply omitting second-order terms.
In a non-sway course example, a local amplification may still be required even when global sway effects are treated as negligible.
Prediction and explained answer.Invented numerical example: , global , local .
What additional moment does each produce?
Answer and reasoning
Convert to metres: and .
;
Do not add them blindly at every section: their locations, directions and the analysis model determine how they contribute.
Mechanism detailsSeparate P–Δ from P–δ
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- The dashed line marks the original frame position; axial compression acts downwards.
- Global displacement Δ creates the additional moment PΔ.
- Local displacement δ is measured from the line joining the displaced ends, and adds Pδ.
Follow the original analysis route.
Do not amplify an already amplified moment or confuse critical-load factor with member slenderness.
Mechanism detailsSeparate P–Δ from P–δ
The complete mechanism is explained below.
Read each stage together with its stated conditions; playback and interaction are not required.
- The dashed line marks the original frame position; axial compression acts downwards.
- Global displacement Δ creates the additional moment PΔ.
- Local displacement δ is measured from the line joining the displaced ends, and adds Pδ.
Follow the original analysis route.
Do not amplify an already amplified moment or confuse critical-load factor with member slenderness.
Result and concise exam wording
Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.
Restraints define the analysis model
Choose an analysis model that represents the actual joints, restraints and possible sway.
Prediction, then explanation. A joint that permits beam rotation does not automatically remove all column moment. Eccentric reactions may still bend the column.
First identify the joint behaviour. Next identify how horizontal forces reach the foundations. Then assess sway sensitivity using the course criterion.
Simple, continuous and semi-continuous construction describe joint modelling. Sway classification describes overall frame response.
Scope. The schematic does not establish restraint stiffness or a stability threshold. Use the stated data and classification rules.
Check and takeaway. An ideal straight frame may still require notional horizontal forces to represent imperfections under the applicable method.
Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.
Apply the reasoning to this section’s data and conditions
(a) Class 1: plastic moment plus rotation.
Class 2: plastic moment with limited rotation.
Class 3: elastic yield.
Class 4: local buckling before gross yield. (b) Draw/label board encasement and profile-following sprayed protection. (c) Draw/label welded plate-girder I and welded four-plate box, including welds. (d) Sketch globalΔ and localδ; second-order elastic analysis satisfies equilibrium on displaced geometry and includes axial-load additional momentsPΔ/ with relevant imperfections.
Misconceptions and checks
Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.
Use the same mechanism: A table value has conditions. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.
Use the same mechanism: Use the property for the physical question. Moving equal area away from an axis increases I about that axis. It does not increase total area.
Apply the reasoning to this section’s data and conditions
- Do not swap Class 2 and Class 3 resistance descriptions.
- Do not invent a protection thickness or fire rating.
- Do not call an ordinary hot-rolled UB a built-up plate girder.
- Do not confuse material nonlinearity with geometric second-order effects.
How the method transfers to a new variant
Make the next decision from the known conditions
Read the specific task below and identify the quantity or explanation it asks for.
Prediction, then explanation. Changing a load value may preserve the method. Changing the support or failure mechanism can require a different method.
Separate given, lookup, calculated and assumed values. State why the model applies. Keep necessary intermediate steps and units beside the equations.
A conditional answer states the exact condition required for its conclusion. It does not fill missing data with a guess.
Scope. A repeated result is not an independent verification. Use equilibrium, dimensions, a reverse substitution or an appropriate limiting case.
Check and takeaway. The explanation and answer are shown together in this edition. No response, score or completed interaction is needed to continue.
Apply the reasoning to this section’s data and conditions
- Identify the term and give its physical meaning.
- Draw the minimum sketch features that distinguish it.
- Label components, axes or displacements.
- State its consequence for resistance/analysis.
- Avoid adding numerical design claims without source inputs.
Prediction with explained answer
Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.
Use the same mechanism: Restraints define the analysis model. A joint that permits beam rotation does not automatically remove all column moment. Eccentric reactions may still bend the column.
Apply the reasoning to this section’s data and conditions
Prediction and explained answer.
Invented transfer question: a braced frame has almost zero storey sway but a visibly bowed compression member.
Can both second-order effects be dismissed?
Answer and reasoning
No. Small globalΔ does not prove localδ is negligible.
Compression acting through the member bow can create local moments.
Follow the course’s non-sway member amplification or appropriate second-order procedure.