STEELWORK / CON4334
Worked examples

Assignment 2 Q1: simple-construction UC with eccentric reactions

Diagrams, explanations and answers are presented in reading order. No playback or response is required.
All answers shownChinese–English terminology
Diagrams, explanations and answers are presented in reading order. No playback or response is required.

Check the Class 1 356×406×287 UC S355 column below the shown floor joint. Actual height 4m; effective length 3.4m about both axes; upper/lower stiffness equal; all moment factors 1. First-order factored centralP4,500 kN, Pₓ₁600 kN at 220mm from y–y, Pᵧ₁900 kN at 320mm from x–x and Pᵧ₂850 kN on the opposite side at 280mm. Amplification 1.1.

Original source: Assignment/AY2627s 1-CON4334-Assignment 2.pdf — p. 1.

A given value comes from the question or diagram.

A lookup value comes from the named table.

A calculated value follows from the working.

Each assumption is stated where the calculation needs it.

Known information, diagram labels and unknowns

Find which plate buckles first

Before using plastic bending resistance, check whether the flange and web can sustain the required stress distribution.

The short waves are local plate buckling. They differ from sideways movement of the whole member.
The short waves are local plate buckling. They differ from sideways movement of the whole member.

Prediction, then explanation. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Calculate the flange and web ratios separately. Compare each with the limits for its stress condition. The worse class governs.

ε=275/py\varepsilon=\sqrt{275/p_y}

py is the design yield strength in N/mm². ε is a dimensionless scale used in the supplied classification limits.

Scope. Pure bending and uniform compression use different web limits. Class 2 allows plastic resistance but not the Class 1 rotation capability.

Check and takeaway. A Class 1 web and Class 2 flange give a Class 2 section. Do not average the class numbers.

Vertical bending can trigger sideways motion

A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.

The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.
The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.

Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.

λ=LE/ry,Mb=pbSx  (Class 1/2),mLTMmax≤Mb\lambda=L_E/r_y,\qquad M_b=p_bS_x\;\text{(Class 1/2)},\qquad m_{LT}M_{max}\le M_b

LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.

Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.

Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.

A force couple carries moment

Separate the force couple used to carry moment from the force used to carry web shear.

The flange forces act in opposite directions. Their separation z gives the lever arm. The web arrow represents shear.
The flange forces act in opposite directions. Their separation z gives the lever arm. The web arrow represents shear.

Prediction, then explanation. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Moment is force multiplied by perpendicular separation. Divide the required moment by the specified separation to obtain each couple force.

F=M/zF=M/z

M is moment in kN·mm; z is the specified force-line separation in mm; F is force in kN.

Scope. Use the lever arm defined by the source model. Do not silently replace it with overall section depth or another geometric distance.

Check and takeaway. Check flange welds for the couple forces and web welds for the stated shear model. Both force paths need a satisfactory detail.

Apply the reasoning to this section’s data and conditions

Lookup: 2023 paper, physical pp.22–23 (printed Data Pages 16–17), exact row 356×406×287 UC.

Read the dimensions/local ratios table and the properties table separately.

The x–x axis crosses the web horizontally; y–y passes vertically through its centre in the table sketch.

PropertyValue and units
Flange/web/root-to-root web depthT=36.5mm、t=22.6mm、d=290.2mm。
Local slendernessbT=5.47、dt=12.8。
Radii (converted from cm)rx=16.5×10=165mm;ry=10.3×10=103mm。
AreaA=366cm2=36600mm2。
Elastic moduliZx=5075cm3;Zy=1939cm3。
Plastic moduliSx=5812cm3;Sy=2949cm3。
LTB parameters

u=0.835, x=10.2.

Both dimensionless

Why this method applies

An eccentric beam reaction bends the column

A simple beam joint delivers a vertical reaction away from the column centre. Find the resulting column moments.

The reaction arrow is offset by e from the column centre. The upper and lower arrows show where the joint moment is shared.
The reaction arrow is offset by e from the column centre. The upper and lower arrows show where the joint moment is shared.

Prediction, then explanation. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Sum axial forces first. Calculate the signed eccentric moments. Share the net joint moment between upper and lower columns using the stated stiffness model.

M=Re,Mlower=MKlowerKupper+KlowerM=Re,\qquad M_{lower}=M\frac{K_{lower}}{K_{upper}+K_{lower}}

R is reaction; e is perpendicular eccentricity. K denotes the stiffness measure prescribed for moment sharing.

Scope. Equal sharing requires equal stated stiffness. Use actual storey length where the special simple-construction LTB rule requires it.

Check and takeaway. A pin-like beam connection can still cause an eccentric reaction moment in the column. Joint rotation and reaction location are separate facts.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: A force couple carries moment. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Apply the reasoning to this section’s data and conditions

Separate the axial sum from the joint moment balance.

All vertical reactions increase the lower column’s compression.

Opposite eccentric reactions subtract for moment, then the equal column stiffnesses split that net moment equally.

Use 3.4m for axial buckling and actual 4m for simple-construction LTB.

(a) Total axial force, joint moments and column moments

Use the same mechanism: An eccentric beam reaction bends the column. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Follow one strip of floor

An area load must become a beam load before beam reactions can be calculated.

The highlighted tributary strip supplies one beam. The right-hand labels show area load multiplied by width becoming line load.
The highlighted tributary strip supplies one beam. The right-hand labels show area load multiplied by width becoming line load.

Prediction, then explanation. At fixed area load, twice the tributary width gives twice the line load. An end reaction remains a concentrated force.

Consider one metre along the beam. The associated floor area is b square metres. Multiply area load by that width.

w=qbw=qb

q is area load in kN/m²; b is tributary width in m; w is line load in kN/m.

Scope. Determine b from slab spanning and supports. Add beam self-weight separately. A secondary-beam reaction is not automatically a UDL.

Check and takeaway. Illustration: 3 kN/m2×2 m=6 kN/m3\,\mathrm{kN/m^2}\times2\,\mathrm{m}=6\,\mathrm{kN/m}. The width cancels one length unit.

Compression acts on the displaced shape

A compressed member moves away from its initial load line. Explain why the bending moment can increase.

The dashed line labelled Original marks the initial position. The tilted member creates the extra horizontal lever arm shown below.
The dashed line labelled Original marks the initial position. The tilted member creates the extra horizontal lever arm shown below.

Prediction, then explanation. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Force acting through an offset forms a moment. Second-order analysis includes that changed geometry in equilibrium.

Madditional=PΔorPδM_{additional}=P\Delta\quad\text{or}\quad P\delta

P is axial force. Δ and δ are the relevant perpendicular displacements. Consistent force and length units give moment units.

Scope. Use the amplification or analysis method stated for the frame. Do not amplify an already amplified moment a second time.

Check and takeaway. Zero offset removes this additional moment in the ideal sketch. Real design may still require imperfections and code checks.

Apply the reasoning to this section’s data and conditions

Physical interpretation: A pinned beam can still bend its column

Its reaction can miss the column centre and create a lever arm.

A pinned beam can still bend its column — Its reaction can miss the column centre and create a lever arm.

Sketch, not to scale; use the original dimensions.

  1. Find the reaction’s actual nominal eccentricity.
  2. Multiply reaction by eccentricity to obtain the joint moment.
  3. Share that moment using the stated column-stiffness model.

Remember: Equal sharing needs equal relevant stiffness.

It is not automatic.

Related concept and full method

Flower=4,500+600+900+850=6,850kNMx,joint=900×3201,000−850×2801,000=288−238=50kN·m|My,joint|=600×2201,000=132kN·mThe upper and lower column IL values are equal; each takes the following share of joint moment: 12. Mx,first=502=25kN·mMy,first=1322=66kN·mMx,amp=MLT=1.1×25=27.5kN·mMy,amp=1.1×66=72.6kN·m

Give both first-order 25/66 and amplified 27.5/72.6kN·m values so the answer to(a) is unambiguous.

Do not split the 6,850kN axial sum between columns.

The problem says centralP includes self-weight.

No additional self-weight is added.

Mechanism detailsEccentric reactions and stiffness sharing3 concepts · 1 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A beam reaction can act away from the column centre even at a nominally pinned beam connection.
  2. .

    Opposing reactions can cancel part of the signed moment, while both still add compression.

  3. The course simple model distributes the joint moment in proportion to of the columns above and below.
  4. Equal relevant stiffness gives half each.

    A roof joint with no upper column is a different case.

(b) Cross-section capacity

A strong cross-section can belong to an unstable member

A column carries axial compression and bending. Explain why more than one check is required.

The three boxes name separate checks: Section, Flexural and LTB. The bottom caption explains that passing one does not pass the others.
The three boxes name separate checks: Section, Flexural and LTB. The bottom caption explains that passing one does not pass the others.

Prediction, then explanation. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Separate cross-section, flexural-buckling and LTB interaction equations. Use each equation’s own denominators and first-order or amplified moments.

AgpyA_g p_y is a section axial resistance. AgpcA_g p_c is a member compression resistance. Elastic pyZp_y Z and prescribed McM_c are different bending denominators.

Scope. Preserve the course barred-moment definitions and Eq. 8.81 convention. Do not substitute plastic moduli into an elastic denominator.

Check and takeaway. Report each requested utilisation and the governing check. The largest properly calculated ratio identifies the closest limit.

Use the same mechanism: Find which plate buckles first. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Apply the reasoning to this section’s data and conditions

Physical interpretation: The column needs more than one pass

A slice can be strong while the whole member still buckles.

The column needs more than one pass — A slice can be strong while the whole member still buckles.

Sketch, not to scale; use the original dimensions.

  1. Check cross-section compression plus bending.
  2. Then check the separate member-buckling expressions.
  3. Keep each moment, factor and resistance in its specified expression.

Remember: The three checks do not share interchangeable denominators.

Related concept and full method

The question permits Class 1.

The supplied property row also supports it; verify the material band and conservative local limits:

T=36.5mm; use the S355 thickness band to select py=345Nmm2. ε=275345=0.892805
Flange bT=5.47; Class 1 limit 9ε=8.035248; Class 2 limit 10ε=8.928054. Flange is Class 1. Web stress parameter: r1=Fdtpy=6850×1,000290.2×22.6×345Limit to 0≤r1≤1, then use 1.000000. For any r1 within this range, a conservative Class 1 web limit is 40ε=35.712215. dt=12.8<35.712215. The web satisfies the stricter bound. Overall Class 1; use capped plastic section resistance.

The lecture’s Class 1 combined-stress web limit 80ε1+r1 cannot be below 40ε because r1≤1.

This check therefore avoids an unjustified plastic classification while remaining conservative.

The flange is checked independently.

At a cross section, compression and bending share the material.

Use amplified moments and capped plastic resistances.

The total must not exceed 1; all terms below are dimensionless.

Agpy=366×100×3451,000=12627kNMx,amp=1.1×25=27.5kN·mMy,amp=1.1×66=72.6kN·mMcx=min(345×58121,000,1.2×345×50751,000)=min(2005.14,2101.05)=2005.14kN·mMcy=min(345×29491,000,1.2×345×19391,000)=min(1017.4,802.746)=802.746kN·mSection ratio: 685012627+27.52005.14+72.6802.746=0.646643Passes.

Mechanism detailsA strong slice can belong to an unstable member5 concepts · 4 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

(c) Both member-buckling interactions

Use the same mechanism: A strong cross-section can belong to an unstable member. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Check buckling about both axes

Determine which buckling direction limits the compressed member.

Compare the outlines labelled Straight and Bowed. The dashed line beside Bowed marks its original straight reference.
Compare the outlines labelled Straight and Bowed. The dashed line beside Bowed marks its original straight reference.

Prediction, then explanation. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Calculate slenderness about each axis. Select each axis’s curve from section type and thickness. Then obtain and compare the two compressive resistances.

λx=LEx/rx,λy=LEy/ry,Pc=pcAg\lambda_x=L_{Ex}/r_x,\quad\lambda_y=L_{Ey}/r_y,\qquad P_c=p_cA_g

Effective lengths and radii use mm. pc is compressive strength in N/mm²; Ag is gross area in mm²; Pc is in N.

Scope. Do not select the governing axis using radius alone. Effective length and buckling curve can differ. A combined column also needs interaction checks.

Check and takeaway. A short-section yield resistance is not the same as long-member buckling resistance. Keep py and pc distinct.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

Physical interpretation: Why a long column can fail before crushing

Push a long thin ruler from both ends: it may bow sideways first.

Why a long column can fail before crushing — Push a long thin ruler from both ends: it may bow sideways first.

Sketch, not to scale; use the original dimensions.

  1. Find effective length and radius of gyration for each axis.
  2. Calculate slenderness for both directions.
  3. Use the appropriate buckling curve before forming resistance.

Remember: Compare the final resistances; slenderness alone may not identify the controlling axis.

Related concept and full method

Simple construction: mx=my=mLT=1 as given.

Effective lengths 3,400mm are already specified, so apply no further K factor.

Table 8.7: hot-rolled H-section (UC), maximum thickness ≤40mm, about the x axis use curve b, about the y axis use curve c.

Use the Data File p.8 py=345Nmm2 column.

The two axes use different curves, so slenderness alone cannot identify the governing axis.

LEx=LEy=3400mm (known effective length).λx=3400165=20.606061λy=3400103=33.009709x axis, curve b: 20 row gives 339; 25 row gives 332Nmm2. Interpolation fraction: 20.606061−2025−20=0.121212pc=339+0.121212×(332−339)=338.151515Nmm2y axis, curve c: 30 row gives 315; 35 row gives 305Nmm2. Interpolation fraction: 33.009709−3035−30=0.601942pc=315+0.601942×(305−315)=308.980583Nmm2Pcx=Apcx10=366×338.15151510=12376.345455kNPcy=366×308.98058310=11308.689320kNPc=min(Pcx,Pcy)=11308.689320kN

Member interaction uses elastic moment denominators pᵧZ, even when the cross-section check used plastic moduli.

Use amplified moments here.

Mex=345×50751,000=1750.88kN·mMey=345×19391,000=668.955kN·mFPc+mxMx,ampMex+myMy,ampMey=685011308.689320+1×27.51750.88+1×72.6668.955=0.729963Passes.

Simple-construction special rule: use actual storey length L in 0.5L/rᵧ.

The axial effective length is a different quantity.

λLT=0.5×4000103=19.417476

Read Data File p.5 Table 8.3a, pᵧ345 column:

Calculated λLT=19.417476, below the first printed row 25. Conservatively use the greater slenderness 25 without extrapolation: pb=345Nmm2, also not exceeding material design strength.Mb=pbSx=345.000000×58121,000=2005.140000kN·m

Course Eq.8.81 uses first-order minor-axis moment in its last term.

Mᴸᵀ is the specified amplified major-axis value.

Do not amplify it twice.

The axial denominator is Pcy.

FPcy+mLTMLTMb+myMy,firstMey=685011308.689320+1×27.52005.140000+1×66668.955=0.718105Passes.

py=345Nmm2; Pcx=12376.345kN, Pcy=11308.689kN; Mcx=2005.140kN·m, Mcy=802.746kN·m.

Mb=2005.140kN·m.

Ratios: section 0.646643; flexural buckling 0.729963; axial force/LTB 0.718105.

All three requested strength checks pass.

The calculated simple-construction value λLT=19.417 is below the first printed Table 8.3a row, 25.

Conservatively read the more slender 25 row to obtain pb=345Nmm2, equal to the material ceiling, without extrapolation.

All three requested checks pass.

Mechanism detailsA strong slice can belong to an unstable member6 concepts · 16 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. Combine axial compression and the two bending demands using the specified section resistances.
  2. The whole member adds effective-length and buckling-curve effects.
  3. This uses its own moment factor and bending resistance.

    It is not a copy of the section check.

  4. Elastic, plastic and buckling resistances are not interchangeable.

    Read the three original expressions and their first-order/amplified moments.

Result and concise exam wording

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

(a) F6,850 kN; net jointMx 50/My 132; lower first-order 25/66 and amplified 27.5/72.6kN·m.

Class 1, pᵧ345; curvesb/c; LE3.4 m, actualL4 m; allm 1.

py=345Nmm2; Pcx=12376.345kN, Pcy=11308.689kN; Mcx=2005.140kN·m, Mcy=802.746kN·m.

Mb=2005.140kN·m.

Ratios: section 0.646643; flexural buckling 0.729963; axial force/LTB 0.718105.

All three requested strength checks pass.

Misconceptions and checks

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

  • Do not replace the missing current-data row by a similarly named 305 UC.
  • Do not add opposite eccentric moments.
  • Do not halve the axial force.
  • Do not apply 0.85 to an effective length that is already given.

How the method transfers to a new variant

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Use the same mechanism: An eccentric beam reaction bends the column. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

  1. Find the exact property row, including supplied supplementary data if necessary.
  2. Sum compression, balance signed joint moments and apply the stiffness fractions.
  3. Amplify once and check the section.
  4. Use each axis’s radius/curve and the correct moment denominators.
  5. Apply the simple-construction LTB length rule and report every check.

Prediction with explained answer

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Two simultaneous actions use one component

Check a component that carries shear and tension, or compression and bending, at the same time.

The bolt receives two labelled arrows: tension and shear. The caption requires both individual checks and the combined check.
The bolt receives two labelled arrows: tension and shear. The caption requires both individual checks and the combined check.

Prediction, then explanation. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

First apply the individual checks. Next use the exact combined equation and its definitions. Keep demands from the same load case.

FsPs+FtPnom≤1.4\frac{F_s}{P_s}+\frac{F_t}{P_{nom}}\le1.4

This is the course bolt interaction rule. Fs and Ft are bolt demands; Ps and Pnom are their specified resistance denominators.

Scope. The 1.4 limit and nominal tension denominator do not apply to column equations. Their limits and moment definitions are separate.

Check and takeaway. A sum above one can pass this bolt rule while still needing individual checks. A pass must name the actual equation used.

Balance the isolated beam

Find the two vertical reactions before calculating internal shear or moment.

A / RₐB / RᵦPaL
A and B are vertical supports. The downward load acts at distance a from A. Its distance from B is L − a.

Prediction, then explanation. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Take moments about A. Reaction A has zero lever arm there. Then use vertical force balance to find reaction A.

RBL=Pa,RA+RB=PR_B L=Pa,\qquad R_A+R_B=P

P, RA and RB are forces in kN. L is support spacing and a is load position, both in m.

Scope. These expressions describe one point load on a simply supported beam. Add other loads through equilibrium; keep their actual positions.

Check and takeaway. Illustration: P = 60 kN, L = 6 m and a = 2 m give RB = 20 kN and RA = 40 kN.

Apply the reasoning to this section’s data and conditions

Prediction and explained answer.

Invented variant: Pᵧ₂ rises from 850 to 950kN.

Does the x-axis moment necessarily increase?

Answer and reasoning

Not necessarily.

Net joint moment Mx=900×0.320−950×0.280=22kN·m.

Therefore, the lower column's first-order Mx becomes 11kN·m; after amplification, Mx=12.1kN·m.

Axial force increases to 6,950kN.

Opposing reactions reduce the net moment but increase compression.

Recalculate every interaction check.

Mechanism detailsEccentric reactions and stiffness sharing4 concepts · 2 source expressions

The complete mechanism is explained below.

Read each stage together with its stated conditions; playback and interaction are not required.

  1. A beam reaction can act away from the column centre even at a nominally pinned beam connection.
  2. .

    Opposing reactions can cancel part of the signed moment, while both still add compression.

  3. The course simple model distributes the joint moment in proportion to of the columns above and below.
  4. Equal relevant stiffness gives half each.

    A roof joint with no upper column is a different case.