Worked Example

Column Q3: biaxial bending of 305×305×198 UC (Column Q3)

Task: Complete the section check and both member checks to determine whether the column passes.

Original question · Lecture notes Chapter 4, p. 40 (Tutorial 4 Q3)
Original question with the given values boxed
Yellow boxes: values the question gives, the same values marked yellow in the Given table below.

The question in short: A 305×305×198 UC column with an effective length of 6 m carries 2500 kN of compression. End moments are 350 and 150 kNm about the xx axis, and 90 and −70 kNm about the yy axis. Complete the section check and both member checks.

What differs from the previous example of this type: The section is heavier than in the previous example, and the top and bottom end moments are now given with their signs. So β\beta is found first and mxm_x, mym_y and mLTm_{LT} are looked up, not all taken as 1.

GivenValue and Unit
Section305×305×198 UC, S355; Ag=252 cm2\htmlClass{read}{A_g=252\ \mathrm{cm^{2}}}; Sx=3440\htmlClass{read}{S_x=3440}, Zx=2995\htmlClass{read}{Z_x=2995}, Sy=1581\htmlClass{read}{S_y=1581}, Zy=1037 cm3\htmlClass{read}{Z_y=1037\ \mathrm{cm^{3}}}; ry=80.4 mm\htmlClass{read}{r_y=80.4\ \mathrm{mm}}; py=345 N/mm2\htmlClass{read}{p_y=345\ \mathrm{N/mm^{2}}}
Axial forceFc=2500 kN\htmlClass{given}{F_c=2500\ \mathrm{kN}}
xx-axis end momentsTop +350, bottom +150 kNm; amplification 1.1
yy-axis end momentsTop +90, bottom −70 kNm; amplification 1.15
Other dataMLT=350 kNm\htmlClass{given}{M_{LT}=350\ \mathrm{kNm}}; Le=6 m\htmlClass{given}{L_e=6\ \mathrm{m}}; u=0.854\htmlClass{read}{u=0.854}; x=10.2\htmlClass{read}{x=10.2}

Yellow: values given in the question. The same values are marked where they are substituted in the steps below.
Orange box: values read directly from the Data File, the same values boxed orange in the lookup screenshots. A value interpolated between two table rows is a calculation, so it has no box.

Data file lookup · Data Page 11 · Universal Columns — Properties
305×305×198 UC: ry = 8.04 cm, Zx = 2995, Zy = 1037, Sx = 3440, Sy = 1581 cm³, u = 0.854, x = 10.2, A = 252 cm².
305×305×198 UC: ry=8.04 cmr_y=8.04\ \mathrm{cm}, Zx=2995Z_x=2995, Zy=1037Z_y=1037, Sx=3440S_x=3440, Sy=1581 cm3S_y=1581\ \mathrm{cm^{3}}, u=0.854u=0.854, x=10.2x=10.2, A=252 cm2A=252\ \mathrm{cm^{2}}.Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too
Data file lookup · Data Page 11 · Universal Columns — Dimensions
305×305×198 UC: flange T = 31.4 mm.
305×305×198 UC: flange T=31.4 mmT=31.4\ \mathrm{mm}.Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too
Data file lookup · Data Page 1 · Design strength pyp_y
T = 31.4 mm thick: the T ≤ 40 mm row, S355 column gives py = 345 N/mm².
T=31.4 mmT=31.4\ \mathrm{mm} thick: the T≤40 mmT\le40\ \mathrm{mm} row, S355 column gives py=345 N/mm2p_y=345\ \mathrm{N/mm^{2}}. How the grade and thickness choose this row →Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too

Solution Route: Amplify demand→section resistance/utilisation→λ/pc\lambda/p_c→β\beta and m factors→first member expression→LTB→second member expression.

Load path · the stations the force passes through, in order

Axial force and end moments about both axes act on the column together. The signs of the end moments fix the m factors, so they change the size of each ratio.

  1. Axial force and amplified moments
    Fc=2500 kNF_c=2500\ \mathrm{kN}; Mx=385M_x=385, My=103.5 kNmM_y=103.5\ \mathrm{kNm}
  2. Cross-section check
    Sum 0.853Limit 1
  3. Member check 1 (buckling)
    Sum 0.951Limit 1
    closest to the limit
  4. Member check 2 (lateral-torsional buckling)
    Sum 0.914Limit 1
Red frame: the station closest to its limit. Each station links to the step that calculates it.
  1. Step 1 · Amplify demand

    Why this step: The end with the larger moment is worked hardest, so it gives the demand. The amplification allows for the extra moment that appears when the compressed column deforms.

    Take the larger end-moment magnitude and apply amplification.

    New symbols in this step
    • MxM_x, MyM_y, MLTM_{LT}: Two-axis and LTB governing moment demands; kNm
    • kxk_x, kyk_y, Mx1M_{x1}, My1M_{y1}: Amplification factors for the two axes; larger end moment before amplification, kNm
    Mx=kxMx1=1.1(350)=385,My=kyMy1=1.15(90)=103.5 kNmM_x=k_xM_{x1}={\htmlClass{given}{1.1}}({\htmlClass{given}{350}})=385,\qquad M_y=k_yM_{y1}={\htmlClass{given}{1.15}}({\htmlClass{given}{90}})=103.5\ \mathrm{kNm}
    Mx=kxMx1=1.1(350)=385My=kyMy1=1.15(90)=103.5 kNm\begin{aligned}M_x&=k_xM_{x1}={\htmlClass{given}{1.1}}({\htmlClass{given}{350}})=385\\M_y&=k_yM_{y1}={\htmlClass{given}{1.15}}({\htmlClass{given}{90}})=103.5\ \mathrm{kNm}\end{aligned}

    ▶ The lecturer on this part: 31 October 01:49:08

  2. Step 2 · Section bending resistance

    Why this step: These are the moments the section itself can carry before it fails in bending, one for each axis. The weak-axis capacity is much smaller, so even a small yy-axis moment uses a sizeable share.

    For each axis take the smaller of pySp_yS and 1.2pyZ. The latter governs yy.

    New symbols in this step
    • AgA_g, pyp_y, pcp_c: Gross area mm²; yield and compression buckling strengths N/mm²
    • McxM_{cx}, McyM_{cy}, MbM_b: Corresponding bending resistances; kNm, with different section/member definitions
    Mcx=min⁡(pySx, 1.2pyZx)=min⁡(345(3440), 1.2(345)(2995))/1000=min⁡(1186.8, 1239.9)=1186.8 kNmMcy=min⁡(pySy, 1.2pyZy)=min⁡(345(1581), 1.2(345)(1037))/1000=min⁡(545.4, 429.3)=429.3 kNm\begin{aligned}M_{cx}&=\min(p_yS_x,\ 1.2p_yZ_x)=\min({\htmlClass{read}{345}}({\htmlClass{read}{3440}}),\ 1.2({\htmlClass{read}{345}})({\htmlClass{read}{2995}}))/1000\\&=\min(1186.8,\ 1239.9)=1186.8\ \mathrm{kNm}\\M_{cy}&=\min(p_yS_y,\ 1.2p_yZ_y)=\min({\htmlClass{read}{345}}({\htmlClass{read}{1581}}),\ 1.2({\htmlClass{read}{345}})({\htmlClass{read}{1037}}))/1000\\&=\min(545.4,\ 429.3)=429.3\ \mathrm{kNm}\end{aligned}
    Mcx=min⁡(pySx, 1.2pyZx)=min⁡(345(3440), 1.2(345)(2995))/1000=min⁡(1186.8, 1239.9)=1186.8 kNmMcy=min⁡(pySy, 1.2pyZy)=min⁡(345(1581), 1.2(345)(1037))/1000=min⁡(545.4, 429.3)=429.3 kNm\begin{aligned}M_{cx}&=\min(p_yS_x,\ 1.2p_yZ_x)\\&=\min({\htmlClass{read}{345}}({\htmlClass{read}{3440}}),\\&\quad \ 1.2({\htmlClass{read}{345}})({\htmlClass{read}{2995}}))/1000\\&=\min(1186.8,\ 1239.9)\\&=1186.8\ \mathrm{kNm}\\M_{cy}&=\min(p_yS_y,\ 1.2p_yZ_y)\\&=\min({\htmlClass{read}{345}}({\htmlClass{read}{1581}}),\\&\quad \ 1.2({\htmlClass{read}{345}})({\htmlClass{read}{1037}}))/1000\\&=\min(545.4,\ 429.3)=429.3\ \mathrm{kNm}\end{aligned}

    Units: SS and ZZ are in cm³ and are multiplied by 1000 to give mm³. pyp_y in N/mm² times mm³ gives Nmm, and dividing by 1000000 gives kNm. Together this is a division by 1000.

    ▶ The lecturer on this part: 31 October 01:59:56

  3. Step 3 · Section check

    Why this step: The three terms are the shares of the section's strength used by compression, the xx-axis moment and the yy-axis moment. A total below 1 means the cross-section at the column end is not crushed.

    Agpy=252(100)(345)/1000=8694 kNA_gp_y=252(100)(345)/1000=8694\ \mathrm{kN}.

    New symbols in this step
    • FcF_c, PcP_c: Design axial force and buckling compression resistance; kN
    Agpy=252(100)(345)/1000=8694 kNηs=FcAgpy+MxMcx+MyMcy=25008694+3851186.8+103.5429.3=0.288+0.324+0.241≈0.853<1\begin{aligned}A_gp_y&={\htmlClass{read}{252}}(100)({\htmlClass{read}{345}})/1000=8694\ \mathrm{kN}\\\eta_s&=\frac{F_c}{A_gp_y}+\frac{M_x}{M_{cx}}+\frac{M_y}{M_{cy}}\\&=\frac{{\htmlClass{given}{2500}}}{8694}+\frac{385}{1186.8}+\frac{103.5}{429.3}\\&=0.288+0.324+0.241\approx0.853<1\end{aligned}
    Agpy=252(100)(345)/1000=8694 kNηs=FcAgpy+MxMcx+MyMcy=25008694+3851186.8+103.5429.3=0.288+0.324+0.241≈0.853<1\begin{aligned}A_gp_y&={\htmlClass{read}{252}}(100)({\htmlClass{read}{345}})/1000\\&=8694\ \mathrm{kN}\\\eta_s&=\frac{F_c}{A_gp_y}+\frac{M_x}{M_{cx}}+\frac{M_y}{M_{cy}}\\&=\frac{{\htmlClass{given}{2500}}}{8694}+\frac{385}{1186.8}+\frac{103.5}{429.3}\\&=0.288+0.324+0.241\\&\approx0.853\\&<1\end{aligned}

    Where the numbers come from: 385385 from Step 1; 1186.81186.8 from Step 2; 103.5103.5 from Step 1; 429.3429.3 from Step 2.

    Units: AgA_g of 252 cm² is multiplied by 100 to change it into mm². pyp_y in N/mm² times mm² gives N, and dividing by 1000 gives kN.

  4. Step 4 · Buckling strength

    Why this step: The column buckles first in its easiest direction, which is about the yy axis. So only ryr_y is needed for slenderness; pcp_c is the compressive stress the column can carry before it bows that way.

    The yy axis is more slender. Use curve c and interpolate between 74 and 76.

    New symbols in this step
    • LeL_e, rxr_x, ryr_y, λ\lambda: Effective length and radius of gyration mm; dimensionless slenderness
    • λ1\lambda_1, λ2\lambda_2, p1p_1, p2p_2: Slenderness and table values of the two rows used for interpolation
    λ=LE/ry=6000/80.4≈74.63pc=p1+λ−λ1λ2−λ1(p2−p1)=202+74.63−7476−74(196−202)≈200.1 N/mm2\begin{aligned}\lambda&=L_E/r_y={\htmlClass{given}{6000}}/{\htmlClass{read}{80.4}}\approx74.63\\p_c&=p_1+\frac{\lambda-\lambda_1}{\lambda_2-\lambda_1}(p_2-p_1)={\htmlClass{read}{202}}+\frac{74.63-{\htmlClass{given}{74}}}{{\htmlClass{given}{76}}-{\htmlClass{given}{74}}}({\htmlClass{read}{196}}-{\htmlClass{read}{202}})\approx200.1\ \mathrm{N/mm^2}\end{aligned}
    λ=LE/ry=6000/80.4≈74.63pc=p1+λ−λ1λ2−λ1(p2−p1)=202+74.63−7476−74(196−202)≈200.1 N/mm2\begin{aligned}\lambda&=L_E/r_y={\htmlClass{given}{6000}}/{\htmlClass{read}{80.4}}\approx74.63\\p_c&=p_1+\frac{\lambda-\lambda_1}{\lambda_2-\lambda_1}(p_2-p_1)\\&={\htmlClass{read}{202}}+\frac{74.63-{\htmlClass{given}{74}}}{{\htmlClass{given}{76}}-{\htmlClass{given}{74}}}({\htmlClass{read}{196}}-{\htmlClass{read}{202}})\\&\approx200.1\ \mathrm{N/mm^2}\end{aligned}

    Units: The 6 m effective length is multiplied by 1000 to give 6000 mm and divided by ryr_y in mm. Millimetres divided by millimetres leave slenderness with no unit.

    Data file lookup · Data Page 8 · Table 8.8(c)
    Table 8.8(c) (y axis, curve c), py = 345 column: λ = 74 → 202 and λ = 76 → 196 N/mm²; interpolating at λ = 74.6 gives pc ≈ 200.1 N/mm².
    Table 8.8(c) (yy axis, curve c), py=345p_y=345 column: λ=74\lambda=74 → 202 and λ=76\lambda=76 → 196 N/mm²; interpolating at λ=74.6\lambda=74.6 gives pc≈200.1 N/mm2p_c\approx200.1\ \mathrm{N/mm^{2}}.Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too

    ▶ The lecturer on this part: 31 October 02:04:55

  5. Step 5 · Buckling resistance

    Why this step: PcP_c is the compression force the whole column can carry before it bows about the weak axis. It is the capacity for the compression term in both member checks.

    Pc=Agpc=252(100)(200.1)/1000≈5043 kNP_c=A_gp_c={\htmlClass{read}{252}}(100)(200.1)/1000\approx5043\ \mathrm{kN}
    Pc=Agpc=252(100)(200.1)/1000≈5043 kN\begin{aligned}P_c&=A_gp_c\\&={\htmlClass{read}{252}}(100)(200.1)/1000\\&\approx5043\ \mathrm{kN}\end{aligned}

    Where the numbers come from: 200.1200.1 from Step 4.

    Units: The area of 252 cm² is multiplied by 100 to change it into mm². pcp_c in N/mm² times mm² gives N, and dividing by 1000 gives kN.

  6. Step 6 · xx-axis factors

    Why this step: When the end moments bend the column into an SS shape, the largest moment occurs only at one end and the middle carries little. This is less harmful for buckling, so mxm_x and mLTm_{LT} are well below 1.

    End moments of the same sign (both clockwise) give double curvature, so β\beta is negative; interpolate between the β=−0.4\beta=-0.4 and −0.5 rows of Tables 8.9 and 8.4a8.4a.

    βx=Msmall/Mlarge=−150/350=−0.429mx=0.52+−0.429−(−0.4)−0.5−(−0.4)(0.50−0.52)≈0.514mLT=0.46+−0.429−(−0.4)−0.5−(−0.4)(0.44−0.46)≈0.454\begin{aligned}\beta_x&=M_{small}/M_{large}=-{\htmlClass{given}{150}}/{\htmlClass{given}{350}}=-0.429\\m_x&={\htmlClass{read}{0.52}}+\frac{-0.429-(-{\htmlClass{given}{0.4}})}{-{\htmlClass{given}{0.5}}-(-{\htmlClass{given}{0.4}})}({\htmlClass{read}{0.50}}-{\htmlClass{read}{0.52}})\approx0.514\\m_{LT}&={\htmlClass{read}{0.46}}+\frac{-0.429-(-{\htmlClass{given}{0.4}})}{-{\htmlClass{given}{0.5}}-(-{\htmlClass{given}{0.4}})}({\htmlClass{read}{0.44}}-{\htmlClass{read}{0.46}})\approx0.454\end{aligned}
    βx=Msmall/Mlarge=−150/350=−0.429mx=0.52+−0.429−(−0.4)−0.5−(−0.4)(0.50−0.52)≈0.514mLT=0.46+−0.429−(−0.4)−0.5−(−0.4)(0.44−0.46)≈0.454\begin{aligned}\beta_x&=M_{small}/M_{large}\\&=-{\htmlClass{given}{150}}/{\htmlClass{given}{350}}\\&=-0.429\\m_x&={\htmlClass{read}{0.52}}+\frac{-0.429-(-{\htmlClass{given}{0.4}})}{-{\htmlClass{given}{0.5}}-(-{\htmlClass{given}{0.4}})}({\htmlClass{read}{0.50}}-{\htmlClass{read}{0.52}})\\&\approx0.514\\m_{LT}&={\htmlClass{read}{0.46}}+\frac{-0.429-(-{\htmlClass{given}{0.4}})}{-{\htmlClass{given}{0.5}}-(-{\htmlClass{given}{0.4}})}({\htmlClass{read}{0.44}}-{\htmlClass{read}{0.46}})\\&\approx0.454\end{aligned}
    Data file lookup · Data Page 7 · Table 8.9
    Table 8.9: β = −0.4 → 0.52 and β = −0.5 → 0.50; interpolating at βx = −0.429 gives mx ≈ 0.514.
    Table 8.9: β=−0.4\beta=-0.4 → 0.52 and β=−0.5\beta=-0.5 → 0.50; interpolating at βx=−0.429\beta_{x}=-0.429 gives mx≈0.514m_x\approx0.514.Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too
    Data file lookup · Data Page 6 · Table 8.4a
    Table 8.4a: β = −0.4 → 0.46 and β = −0.5 → 0.44; interpolating at β = −0.429 gives mLT ≈ 0.454.
    Table 8.4a: β=−0.4\beta=-0.4 → 0.46 and β=−0.5\beta=-0.5 → 0.44; interpolating at β=−0.429\beta=-0.429 gives mLT≈0.454m_{LT}\approx0.454.Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too
  7. Step 7 · yy-axis factors

    Why this step: When the end moments bend the column to the same side, a fairly large moment acts along the whole length, in a shape like the bow of buckling. This is more severe, so mym_y is close to 1.

    End moments of opposite sign give single curvature, so β\beta is positive; interpolate between the β=0.7\beta=0.7 and 0.8 rows of Table 8.9.

    βy=Msmall/Mlarge=70/90=0.778my=0.88+0.778−0.70.8−0.7(0.92−0.88)≈0.911\begin{aligned}\beta_y&=M_{small}/M_{large}={\htmlClass{given}{70}}/{\htmlClass{given}{90}}=0.778\\m_y&={\htmlClass{read}{0.88}}+\frac{0.778-{\htmlClass{given}{0.7}}}{{\htmlClass{given}{0.8}}-{\htmlClass{given}{0.7}}}({\htmlClass{read}{0.92}}-{\htmlClass{read}{0.88}})\approx0.911\end{aligned}
    βy=Msmall/Mlarge=70/90=0.778my=0.88+0.778−0.70.8−0.7(0.92−0.88)≈0.911\begin{aligned}\beta_y&=M_{small}/M_{large}={\htmlClass{given}{70}}/{\htmlClass{given}{90}}=0.778\\m_y&={\htmlClass{read}{0.88}}+\frac{0.778-{\htmlClass{given}{0.7}}}{{\htmlClass{given}{0.8}}-{\htmlClass{given}{0.7}}}({\htmlClass{read}{0.92}}-{\htmlClass{read}{0.88}})\\&\approx0.911\end{aligned}
    Data file lookup · Data Page 7 · Table 8.9
    Table 8.9: β = 0.7 → 0.88 and β = 0.8 → 0.92; interpolating at βy = 0.778 gives my ≈ 0.911.
    Table 8.9: β=0.7\beta=0.7 → 0.88 and β=0.8\beta=0.8 → 0.92; interpolating at βy=0.778\beta_{y}=0.778 gives my≈0.911m_y\approx0.911.Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too
  8. Step 8 · First member expression

    Why this step: This check adds the bowing caused by compression to the extra bending from the moments about both axes. The m factors multiply the moments so that only the part that matters for buckling is counted.

    The denominators are the elastic capacities pyZp_yZ.

    New symbols in this step
    • mxm_x, mym_y, mLTm_{LT}: Equivalent moment-distribution factors; dimensionless
    pyZx=345(2995)/1000=1033.3,pyZy=345(1037)/1000=357.8 kNmFcPc+mxMxpyZx+myMypyZy=25005043+0.514(385)1033.3+0.911(103.5)357.8=0.496+0.192+0.264≈0.951<1\begin{aligned}p_yZ_x&={\htmlClass{read}{345}}({\htmlClass{read}{2995}})/1000=1033.3,\quad p_yZ_y={\htmlClass{read}{345}}({\htmlClass{read}{1037}})/1000=357.8\ \mathrm{kNm}\\&\frac{F_c}{P_c}+\frac{m_xM_x}{p_yZ_x}+\frac{m_yM_y}{p_yZ_y}\\&=\frac{{\htmlClass{given}{2500}}}{5043}+\frac{0.514(385)}{1033.3}+\frac{0.911(103.5)}{357.8}\\&=0.496+0.192+0.264\approx0.951<1\end{aligned}
    pyZx=345(2995)/1000=1033.3pyZy=345(1037)/1000=357.8 kNmFcPc+mxMxpyZx+myMypyZy=25005043+0.514(385)1033.3+0.911(103.5)357.8=0.496+0.192+0.264≈0.951<1\begin{aligned}p_yZ_x&={\htmlClass{read}{345}}({\htmlClass{read}{2995}})/1000=1033.3\\p_yZ_y&={\htmlClass{read}{345}}({\htmlClass{read}{1037}})/1000\\&=357.8\ \mathrm{kNm}\\&\frac{F_c}{P_c}+\frac{m_xM_x}{p_yZ_x}+\frac{m_yM_y}{p_yZ_y}\\&=\frac{{\htmlClass{given}{2500}}}{5043}+\frac{0.514(385)}{1033.3}+\frac{0.911(103.5)}{357.8}\\&=0.496+0.192+0.264\\&\approx0.951\\&<1\end{aligned}

    Where the numbers come from: 50435043 from Step 5; 0.5140.514 from Step 6; 385385 from Step 1; 0.9110.911 from Step 7; 103.5103.5 from Step 1.

    Units: ZxZ_x and ZyZ_y are in cm³ and are multiplied by 1000 to give mm³. pyp_y times mm³ gives Nmm, and dividing by 1000000 gives kNm, so the formula divides by 1000.

    ▶ The lecturer on this part: 31 October 02:09:50

  9. Step 9 · LTB resistance

    Why this step: The xx-axis moment compresses one flange, which can move sideways and twist the column. The factors uu and vv allow for the section's resistance to twisting and turn the weak-axis slenderness into λLT\lambda_{LT}.

    v=1(1+0.05(λ/x)2)0.25=1(1+0.05(74.63/10.2)2)0.25=0.7222λLT=uvλ=0.854(0.7222)(74.63)≈46.03\begin{aligned}v&=\frac{1}{(1+0.05(\lambda/x)^2)^{0.25}}\\&=\frac{1}{(1+0.05(74.63/{\htmlClass{read}{10.2}})^2)^{0.25}}=0.7222\\\lambda_{LT}&=uv\lambda={\htmlClass{read}{0.854}}(0.7222)(74.63)\approx46.03\end{aligned}
    v=1(1+0.05(λ/x)2)0.25=1(1+0.05(74.63/10.2)2)0.25=0.7222λLT=uvλ=0.854(0.7222)(74.63)≈46.03\begin{aligned}v&=\frac{1}{(1+0.05(\lambda/x)^2)^{0.25}}\\&=\frac{1}{(1+0.05(74.63/{\htmlClass{read}{10.2}})^2)^{0.25}}=0.7222\\\lambda_{LT}&=uv\lambda\\&={\htmlClass{read}{0.854}}(0.7222)(74.63)\\&\approx46.03\end{aligned}

    Where the numbers come from: 74.6374.63 from Step 4.

    ▶ The lecturer on this part: 31 October 02:14:58

  10. Step 10 · Find pbp_b and MbM_b

    Why this step: pbp_b is the bending stress the column can carry before its flange moves sideways. A stocky UC section does not twist easily, so pbp_b is only a little below pyp_y. MbM_b goes into the second member check.

    Interpolate between λLT=45\lambda_{LT}=45→302 and 50→285.

    pb=p1+λLT−λ1λ2−λ1(p2−p1)=302+46.03−4550−45(285−302)≈298.5 N/mm2Mb=pbSx=298.5(3440)/1000≈1026.9 kNm\begin{aligned}p_b&=p_1+\frac{\lambda_{LT}-\lambda_1}{\lambda_2-\lambda_1}(p_2-p_1)\\&={\htmlClass{read}{302}}+\frac{46.03-{\htmlClass{given}{45}}}{{\htmlClass{given}{50}}-{\htmlClass{given}{45}}}({\htmlClass{read}{285}}-{\htmlClass{read}{302}})\approx298.5\ \mathrm{N/mm^2}\\M_b&=p_bS_x=298.5({\htmlClass{read}{3440}})/1000\approx1026.9\ \mathrm{kNm}\end{aligned}
    pb=p1+λLT−λ1λ2−λ1(p2−p1)=302+46.03−4550−45(285−302)≈298.5 N/mm2Mb=pbSx=298.5(3440)/1000≈1026.9 kNm\begin{aligned}p_b&=p_1+\frac{\lambda_{LT}-\lambda_1}{\lambda_2-\lambda_1}(p_2-p_1)\\&={\htmlClass{read}{302}}+\frac{46.03-{\htmlClass{given}{45}}}{{\htmlClass{given}{50}}-{\htmlClass{given}{45}}}({\htmlClass{read}{285}}-{\htmlClass{read}{302}})\\&\approx298.5\ \mathrm{N/mm^2}\\M_b&=p_bS_x\\&=298.5({\htmlClass{read}{3440}})/1000\\&\approx1026.9\ \mathrm{kNm}\end{aligned}

    Where the numbers come from: 46.0346.03 from Step 9.

    Units: SxS_x is in cm³ and is multiplied by 1000 to give mm³. pbp_b in N/mm² times mm³ gives Nmm, and dividing by 1000000 gives kNm. Together this is a division by 1000.

    Data file lookup · Data Page 5 · Table 8.3a
    Table 8.3a, py = 345 column: λLT = 45 → 302 and λLT = 50 → 285 N/mm²; interpolating at λLT = 46.0 gives pb ≈ 298.5 N/mm².
    Table 8.3a, py=345p_y=345 column: λLT=45\lambda_{LT}=45 → 302 and λLT=50\lambda_{LT}=50 → 285 N/mm²; interpolating at λLT=46.0\lambda_{LT}=46.0 gives pb≈298.5 N/mm2p_b\approx298.5\ \mathrm{N/mm^{2}}.Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too
  11. Step 11 · Second member expression

    Why this step: This check asks whether the column, while in compression, moves sideways and twists under the xx-axis moment. The xx-axis term now uses mLTm_{LT}, MLTM_{LT} and MbM_b; the other two terms stay the same.

    FcPc+mLTMLTMb+myMypyZy=25005043+0.454(350)1026.9+0.911(103.5)357.8=0.496+0.155+0.264≈0.914<1\begin{aligned}&\frac{F_c}{P_c}+\frac{m_{LT}M_{LT}}{M_b}+\frac{m_yM_y}{p_yZ_y}\\&=\frac{{\htmlClass{given}{2500}}}{5043}+\frac{0.454({\htmlClass{given}{350}})}{1026.9}+\frac{0.911(103.5)}{357.8}\\&=0.496+0.155+0.264\approx0.914<1\end{aligned}
    FcPc+mLTMLTMb+myMypyZy=25005043+0.454(350)1026.9+0.911(103.5)357.8=0.496+0.155+0.264≈0.914<1\begin{aligned}&\frac{F_c}{P_c}+\frac{m_{LT}M_{LT}}{M_b}+\frac{m_yM_y}{p_yZ_y}\\&=\frac{{\htmlClass{given}{2500}}}{5043}+\frac{0.454({\htmlClass{given}{350}})}{1026.9}+\frac{0.911(103.5)}{357.8}\\&=0.496+0.155+0.264\\&\approx0.914\\&<1\end{aligned}

    Where the numbers come from: 50435043 from Step 5; 0.4540.454 from Step 6; 1026.91026.9 from Step 10; 0.9110.911 from Step 7; 103.5103.5 from Step 1.

    Load path · How the ratios add up
    Limit 1Cross-section0.2880.3240.241≈ 0.853Member 1 (buckling)0.4960.1920.264≈ 0.951Member 2 (LTB)0.4960.1550.264≈ 0.914Axial termx-axis moment termy-axis moment term
    Each bar is one check: blue is the share used by the axial force, green and yellow the shares used by the moments about the two axes. Together they must not pass the red dashed line.

    ▶ The lecturer on this part: 31 October 02:17:26

Conclusion

Section utilisation 0.853 and member utilisations 0.951/0.914 are all below 1. The column passes. End-moment signs directly affect m factors; retain them when copying the question.

All the symbols of this example

SymbolsMeaning and Units
FcF_c, PcP_cDesign axial force and buckling compression resistance; kN
AgA_g, pyp_y, pcp_cGross area mm²; yield and compression buckling strengths N/mm²
LeL_e, rxr_x, ryr_y, λ\lambdaEffective length and radius of gyration mm; dimensionless slenderness
MxM_x, MyM_y, MLTM_{LT}Two-axis and LTB governing moment demands; kNm
SxS_x, SyS_y, ZxZ_x, ZyZ_yTwo-axis plastic/elastic moduli; convert the tabulated cm³
McxM_{cx}, McyM_{cy}, MbM_bCorresponding bending resistances; kNm, with different section/member definitions
mxm_x, mym_y, mLTm_{LT}Equivalent moment-distribution factors; dimensionless
ηs\eta_s, η1\eta_1, η2\eta_2Total utilisations for the section and two member expressions; dimensionless
kxk_x, kyk_y, Mx1M_{x1}, My1M_{y1}Amplification factors for the two axes; larger end moment before amplification, kNm
λ1\lambda_1, λ2\lambda_2, p1p_1, p2p_2Slenderness and table values of the two rows used for interpolation

Video positions: 31 October 01:50:00 · 31 October 02:00:00 · 31 October 02:05:00 · 31 October 02:15:00 · 31 October 02:17:30

↑ Top