STEELWORK / CON4334
Exam crash course · From zero

Steelwork crash course: understand it first, then score well

This crash course is for students who start with little or no background but want to do well in the exam. The aim is not to become an expert. It teaches what the exam actually asks: the steps for each question type, which table to use, and where marks are usually lost.

Suggested route: read 0. Core skills → the compulsory floor beams → then master two Section B question types. Every page walks through a recent exam question step by step.

What is this subject really about?

Picture the steel skeleton of a building. Floor slabs sit on steel beams. The beams pass their load to steel columns, and the columns pass it down to the foundations. The pieces are joined by bolts or welds; these joints are called connections.

So almost every calculation question answers the same three questions:

  1. Demand: how much force must this member carry?

    Work out the shear VV, bending moment MM or axial force FF from the loads.

  2. Capacity (resistance): how much can it carry?

    Look up the section properties and design strength, then use the formula.

  3. Compare: is demand ≤ capacity?

    Yes → it passes (OK). No → it fails; choose a bigger section or more bolts.

Demand  ≤  Capacity⇒OK\text{Demand}\;\le\;\text{Capacity}\quad\Rightarrow\quad\text{OK}

What does the exam look like?

The exam lasts two hours. Section A is compulsory (40 marks). In Section B you answer two of three questions (30 marks each). You answer 100 marks in total.

QuestionMarksWhat it asksLast four papers
A: Floor beams36Slab load → beam shear and moment → section class → shear, bending and deflection checks4 / 4 (compulsory)
A: Short theory4Fire protection, corrosion, rolled sections, second-order effects, etc.4 / 4 (compulsory)
B: Connections30Bolt shear and bearing, angle/plate tension, eccentric weld group4 / 4
B: Columns30Section class, cross-section capacity, member buckling4 / 4
B: Unrestrained beams (LTB)30Reactions, shear and moment diagrams, segment-by-segment LTB checks4 / 4

Timing: roughly one minute per mark. Spend 5 minutes reading and choosing your Section B questions, about 42 minutes on Section A, about 32 minutes on each Section B question, and keep 9 minutes to check units and conclusions (120 minutes in all).

Which two Section B questions should I choose?

QuestionWhat it is likeGood for
Unrestrained beams (LTB)Uses the same beam skills as the compulsory question (reactions, moment diagram), then table look-ups.Students who want one skill set to score twice — most recommended.
ColumnsThe most fixed procedure: classify → section check → two interaction formulas. Mostly look-ups and substitution.Students who like following a fixed recipe.
ConnectionsSeveral small parts (bolt shear, bearing, tension, welds). Each formula is short, but the details vary more.Students who like short formulas and will learn the details.

The six-step method for every question

Whatever the question type, the same six steps work:

  1. Read the drawing and list the data

    Write down the dimensions, loads, section size (e.g. 356×127×39 UB) and steel grade (S275 / S355).

  2. Factor the loads

    Design load =1.4×=1.4\times dead load + 1.6×+\,1.6\times imposed load. If the question says the loads are already factored, do not factor again.

  3. Find the internal forces

    Use equilibrium to get reactions, shear VV and bending moment MM (for a column: axial force and moments).

  4. Look up the tables

    Find the section dimensions and properties in the Data File. Choose the design strength pyp_y from the plate thickness.

  5. Use the capacity formula

    For example the shear capacity VcV_c or moment capacity McM_c.

  6. Compare and conclude

    For example “V=123.8 kN<Vc=478.1 kNV=123.8\text{ kN}<V_c=478.1\text{ kN}, therefore OK”. Write a conclusion for every check.

Study map

Concept maps: understand the “why” first

Each concept map borrows the Understand Anything approach and breaks a hard idea into “cause → key idea → result → how design deals with it → exam answer”. Tap any box to see where it comes from and what it leads to, or follow the guided tour. The theory maps also give English model sentences.

Calculation maps (where every number comes from and goes): pyp_y and classification, floor beams, bolts, eccentric weld, columns, LTB.

A seven-day study plan

DayWhat to do
Day 1Core skills (units, loads, reactions, moments, tables) + learn the short theory answers.
Day 2Floor beams: read the method, then follow the 2024 Q1 walkthrough.
Day 3Floor beams: do the 2023 and 2022 Q1 yourself, then check the answers.
Day 4LTB beams: read the method, follow the 2024 BQ4 walkthrough, then do 2023 yourself.
Day 5Your second Section B type (columns or connections): read the method and do the 2024 question.
Day 6Repeat with the 2023 and 2022 questions of the same types; write down your mistakes.
Day 7Sit the mock paper in two hours; revise the formula sheet.

More time? Do one or two older papers for each question type (2014–2019 answers are under past papers).

How to use this website

  • Crash-course pages (this series): read first to learn the steps for each question type.
  • Lecture pages (Introduction, Connections, Beams, Columns): use them when you want to know “why”. Every section shows how important it is for the exam: ★★★ always examined, ★★ often examined, ★ background.
  • Past-paper answers: for practice. Try first, then open the answer.
  • Formula sheet: the last thing to read before the exam.