Worked Example

Single welded angle: check the member, then allocate welds (Welded Angle)

Task: Understand that angle resistance and weld transfer are separate checks, and allocate both weld lengths by centroid equilibrium.

Original question · Lecture notes Chapter 2, p. 42 (Example 9)
Original question with the given values boxed
Yellow boxes: values the question gives, the same values marked yellow in the Given table below.

The question in short: A 75×50×6 angle carries a tension from a dead load of 95 kN and an imposed load of 40 kN, and is fixed to a connecting plate with 4 mm fillet welds. Check that the angle itself is not pulled apart, then decide how long the weld on each side must be.

What differs from the previous example of this type: The previous example was a symmetric plate with four equal welds. Here the member is an angle whose centroid is off-centre, so the two side welds differ in length, and the design force must first be found using load factors.

GivenValue and Unit
Section and loading75×50×6 angle, S355; DL 95, LL 40 kN
Dimensions on the figureLeg centreline lengths 72 and 47 mm; centroid 24.4 mm from side XX and 50.6 mm from side YY
WeldsTry a 4 mm fillet weld; pw=250 N/mm2\htmlClass{read}{p_w=250\ \mathrm{N/mm^{2}}} (the question does not state the electrode; the lecturer takes class 42)

Yellow: values given in the question. The same values are marked where they are substituted in the steps below.
Orange box: values read directly from the Data File, the same values boxed orange in the lookup screenshots. A value interpolated between two table rows is a calculation, so it has no box.

Data file lookup · Data Page 12 · Unequal Angles
75×50×6 angle: the table gives cx = 2.44 cm = 24.4 mm, the same as the 24.4 mm on the figure; the other side is 75 − 24.4 = 50.6 mm.
75×50×6 angle: the table gives cx=2.44 cm=24.4 mmc_x=2.44\ \mathrm{cm}=24.4\ \mathrm{mm}, the same as the 24.4 mm on the figure; the other side is 75 − 24.4 = 50.6 mm.Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too

Solution Route: Design force→single-leg welded-angle resistance→total weld length→two-side equilibrium→actual lengths and selections.

Interactive 3D model · drag to turn

This browser cannot show the 3D model.

The long leg lies on the plate with one longitudinal weld on each side. The force acts through the centroid, 24.4 mm from side XX and 50.6 mm from side YY, so the nearer side XX carries more and has the longer weld (200 mm against 100 mm).Yellow: values given in the question; orange box: values read from the Data File; white: calculated results; red arrows: forces.
Load path · the stations the force passes through, in order

The tension acts along the centroid line of the angle and passes through the two longitudinal welds into the plate. The centroid is off-centre, so the two welds share the force unequally.

  1. Design tension
    F=197 kNF=197\ \mathrm{kN}
    Step 1
  2. Angle in tension
    Demand 197 kNCapacity 223.44 kN
    Utilisation 0.88
    Step 2
  3. Weld on side XX (nearer the centroid)
    Needs 197.87 mmUse 200 mm
    Step 3–6
  4. Weld on side YY (farther away)
    Needs 99.56 mmUse 100 mm
    Step 5–6
  5. Connecting plate
    Receives the whole 197 kN from the two welds
    Step 3
Each station links to the step that calculates it. Press “Show on the 3D model” to light up that part of the model above; press again to clear.
  1. Step 1 · Design force

    Why this step: The loads given have not yet been multiplied by load factors. Factoring them gives a larger design force, which every later capacity is compared with, so a safety margin is built in.

    Use the lecturer's load combination.

    New symbols in this step
    • PP, FF: Applied force; kN
    • GkG_k, QkQ_k: Unfactored dead and imposed loads; kN
    F=1.4Gk+1.6Qk=1.4(95)+1.6(40)=197 kNF=1.4G_k+1.6Q_k=1.4({\htmlClass{given}{95}})+1.6({\htmlClass{given}{40}})=197\ \mathrm{kN}
    F=1.4Gk+1.6Qk=1.4(95)+1.6(40)=197 kN\begin{aligned}F&=1.4G_k+1.6Q_k\\&=1.4({\htmlClass{given}{95}})+1.6({\htmlClass{given}{40}})\\&=197\ \mathrm{kN}\end{aligned}
  2. Step 2 · Angle resistance

    Why this step: First confirm the angle itself will not be pulled apart. Only one leg is welded to the plate and the other leg carries less, so the area of the unconnected leg is discounted.

    The figure already gives the leg lengths ss along the thickness centreline, 72 and 47 mm; multiplied by the 6 mm thickness they give the two leg areas. A welded joint has no holes, so the effective area is the gross area AgA_g. A welded single angle uses the 0.3 reduction for the unconnected leg, not the 0.5 of the bolted example.

    New symbols in this step
    • ee, rr: Eccentricity and weld-group corner radius; mm
    • a1a_1, a2a_2, PtP_t: Connected/outstanding angle-leg areas mm²; tension resistance kN
    a1=72(6)=432,a2=47(6)=282 mm2Ae=a1+a2=432+282=714 mm2Pt=py(Ae−0.3a2)=355(714−0.3(282))/1000≈223.44 kN\begin{aligned}a_1&={\htmlClass{given}{72}}({\htmlClass{given}{6}})=432,\quad a_2={\htmlClass{given}{47}}({\htmlClass{given}{6}})=282\ \mathrm{mm^2}\\A_e&=a_1+a_2=432+282=714\ \mathrm{mm^2}\\P_t&=p_y(A_e-{\htmlClass{read}{0.3}}a_2)={\htmlClass{read}{355}}(714-{\htmlClass{read}{0.3}}(282))/1000\approx223.44\ \mathrm{kN}\end{aligned}
    a1=72(6)=432a2=47(6)=282 mm2Ae=a1+a2=432+282=714 mm2Pt=py(Ae−0.3a2)=355(714−0.3(282))/1000≈223.44 kN\begin{aligned}a_1&={\htmlClass{given}{72}}({\htmlClass{given}{6}})=432\\a_2&={\htmlClass{given}{47}}({\htmlClass{given}{6}})=282\ \mathrm{mm^2}\\A_e&=a_1+a_2=432+282=714\ \mathrm{mm^2}\\P_t&=p_y(A_e-{\htmlClass{read}{0.3}}a_2)\\&={\htmlClass{read}{355}}(714-{\htmlClass{read}{0.3}}(282))/1000\\&\approx223.44\ \mathrm{kN}\end{aligned}

    Units: The discounted area in mm² times pyp_y in N/mm² gives N. Dividing by 1000 turns N into kN so it can be compared with the design force.

    Data file lookup · Data Page 2 · Tension members
    For a single angle welded through one leg, Pt = py(Ae − 0.3a2).
    For a single angle welded through one leg, Pt=py(Ae−0.3a2)P_t=p_y(A_e-0.3a_2).Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too
    Data file lookup · Data Page 1 · Design strength pyp_y
    Angle 6 mm thick: the T ≤ 16 mm row, S355 column gives py = 355 N/mm².
    Angle 6 mm thick: the T≤16 mmT\le16\ \mathrm{mm} row, S355 column gives py=355 N/mm2p_y=355\ \mathrm{N/mm^{2}}. How the grade and thickness choose this row →Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too

    ▶ The lecturer on this part: 3 October Recording A 00:34:47

  3. Step 3 · Weld-length demand

    Why this step: All the tension in the angle reaches the connecting plate through the welds. Finding what the throat of each millimetre of weld can carry shows how much weld is needed to avoid shearing.

    After the member passes, design transfer of 197 kN to the connecting plate.

    New symbols in this step
    • pwp_w, qwq_w: Weld design strength N/mm²; resistance per millimetre kN/mm
    qw=0.7spw=0.7(4)(250)/1000=0.7 kN/mmq_w=0.7sp_w=0.7({\htmlClass{given}{4}})({\htmlClass{read}{250}})/1000=0.7\ \mathrm{kN/mm}
    qw=0.7spw=0.7(4)(250)/1000=0.7 kN/mm\begin{aligned}q_w&=0.7sp_w\\&=0.7({\htmlClass{given}{4}})({\htmlClass{read}{250}})/1000\\&=0.7\ \mathrm{kN/mm}\end{aligned}

    Units: Leg size in mm times 0.7 gives the throat in mm; times pwp_w in N/mm² gives N per mm. Dividing by 1000 turns it into kN per mm.

    Data file lookup · Data Page 3 · Design strength of fillet weld pwp_w
    For S355 steel with class 42 electrodes the fillet weld design strength is pw = 250 N/mm².
    For S355 steel with class 42 electrodes the fillet weld design strength is pw=250 N/mm2p_w=250\ \mathrm{N/mm^{2}}.Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too
  4. Step 4 · Total effective weld length

    Why this step: The result is the least load-carrying length for both sides together. It does not yet say which side is longer and which is shorter.

    Initially assume the two longitudinal welds share axial force.

    Ltotal=F/qw=197/0.7≈281.43 mmL_{total}=F/q_w=197/0.7\approx281.43\ \mathrm{mm}
    Ltotal=F/qw=197/0.7≈281.43 mm\begin{aligned}L_{total}&=F/q_w\\&=197/0.7\\&\approx281.43\ \mathrm{mm}\end{aligned}

    Where the numbers come from: 197197 from Step 1.

  5. Step 5 · Allocate by centroid position

    Why this step: The pull in the angle acts along its centroid line. The side nearer the centroid takes more force and so gets the longer weld; then the two sides balance and the joint is not twisted.

    Pair the lever arms through moment equilibrium. If XX is 24.4 mm from the centroid and YY 50.6 mm, LX×24.4=LY×50.6L_X\times24.4=L_Y\times50.6.

    New symbols in this step
    • cXc_X, cYc_Y: Distances from the two welds to the angle centroid; mm
    LX=LtotalcYcX+cY=281.43(50.6)/75≈189.87 mmLY=Ltotal−LX=281.43−189.87≈91.56 mm\begin{aligned}L_X&=L_{total}\frac{c_Y}{c_X+c_Y}=281.43({\htmlClass{given}{50.6}})/{\htmlClass{given}{75}}\approx189.87\ \mathrm{mm}\\L_Y&=L_{total}-L_X=281.43-189.87\approx91.56\ \mathrm{mm}\end{aligned}
    LX=LtotalcYcX+cY=281.43(50.6)/75≈189.87 mmLY=Ltotal−LX=281.43−189.87≈91.56 mm\begin{aligned}L_X&=L_{total}\frac{c_Y}{c_X+c_Y}\\&=281.43({\htmlClass{given}{50.6}})/{\htmlClass{given}{75}}\\&\approx189.87\ \mathrm{mm}\\L_Y&=L_{total}-L_X\\&=281.43-189.87\\&\approx91.56\ \mathrm{mm}\end{aligned}

    Where the numbers come from: 281.43281.43 from Step 4.

    Load path · How the two welds share the tension
    F = 197 kNFX​ ≈ 132.9 kNFY​ ≈ 64.1 kNcX​ = 24.4cY​ = 50.6LX​ = 189.87 mmLY​ = 91.56 mmWeld on side X (heel)Weld on side Y (toe)Centroid as in the question75×50×6 angle (connected leg in plan): total effective weld length L = 281.43 mmMoments about the centroid: FX cX​ = FY cY​; the nearer side carries more.LX​ = L × cY​ / (cX​ + cY​) = 281.43 × 50.6 / 75 = 189.87 mm
    The tension acts on the centroid line. The moments of the two weld forces about the centroid must cancel, so side XX, nearer the centroid, carries more force and needs the longer weld. Lengths shown are effective lengths, before adding 2s2s.
  6. Step 6 · Add end allowances

    Why this step: The start and end of each weld are not counted as carrying load, so both sides are lengthened and then rounded up to lengths that are easy to measure on site.

    Add 2s=8 mm2s=8\ \mathrm{mm} to each side, then select 200 and 100 mm.

    New symbols in this step
    • ss, aa: Leg size and effective throat; mm, with a≈0.7sa\approx0.7s in this course
    LX,actual≥LX+2s=189.87+2(4)=197.87→200 mmLY,actual≥LY+2s=91.56+2(4)=99.56→100 mm\begin{aligned}L_{X,actual}&\ge L_X+2s=189.87+2({\htmlClass{given}{4}})=197.87\to200\ \mathrm{mm}\\L_{Y,actual}&\ge L_Y+2s=91.56+2({\htmlClass{given}{4}})=99.56\to100\ \mathrm{mm}\end{aligned}
    LX,actual≥LX+2s=189.87+2(4)=197.87→200 mmLY,actual≥LY+2s=91.56+2(4)=99.56→100 mm\begin{aligned}L_{X,actual}&\ge L_X+2s\\&=189.87+2({\htmlClass{given}{4}})\\&=197.87\to200\ \mathrm{mm}\\L_{Y,actual}&\ge L_Y+2s\\&=91.56+2({\htmlClass{given}{4}})\\&=99.56\to100\ \mathrm{mm}\end{aligned}

    Where the numbers come from: 189.87189.87 from Step 5; 91.5691.56 from Step 5.

Conclusion

Unequal lengths place the resultant FRF_R through the centroid, avoiding additional eccentricity ee. Confirm both angle tension and weld resistance.

All the symbols of this example

SymbolsMeaning and Units
ss, aaLeg size and effective throat; mm, with a≈0.7sa\approx0.7s in this course
pwp_w, qwq_wWeld design strength N/mm²; resistance per millimetre kN/mm
PP, FFApplied force; kN
ee, rrEccentricity and weld-group corner radius; mm
a1a_1, a2a_2, PtP_tConnected/outstanding angle-leg areas mm²; tension resistance kN
GkG_k, QkQ_kUnfactored dead and imposed loads; kN
cXc_X, cYc_YDistances from the two welds to the angle centroid; mm

Video positions: 3 October Recording A 00:30:00 · 3 October Recording A 00:35:00

↑ Top