Worked Example

M27 plate bearing: calculate all four bounds (Four Bearing Limits)

Task: Identify the geometry and material used by each candidate resistance.

The question in short: One M27 bolt bears on a 14 mm plate. The end distance is 70 mm, the clear distance between holes is 50 mm, and the demand is about 166.7 kN per bolt. Work out the four bearing limits of the plate and compare the smallest with the demand.

What differs from the previous example of this type: Unlike the earlier full-joint examples, only the bearing of one plate is checked here, with the four limits taken apart one by one.

GivenValue and Unit
Geometryd=27\htmlClass{given}{d=27}, tp=14\htmlClass{given}{t_p=14}, e=70\htmlClass{given}{e=70}, le=50 mm\htmlClass{given}{l_e=50\ \mathrm{mm}}; standard holes kbs=1\htmlClass{read}{k_{bs}=1}
Materialpbs=550\htmlClass{read}{p_{bs}=550}; Us=510\htmlClass{read}{U_s=510}; Ub=800 N/mm2\htmlClass{read}{U_b=800\ \mathrm{N/mm^{2}}}
DemandApproximately 166.7 kN per bolt on the lecturer's screen

Yellow: values given in the question. The same values are marked where they are substituted in the steps below.
Orange box: values read directly from the Data File, the same values boxed orange in the lookup screenshots. A value interpolated between two table rows is a calculation, so it has no box.

Data file lookup · Data Page 4 · Bearing of connected part
Standard holes give kbs = 1.0. For S355 plate the bearing strength is pbs = 550 N/mm² and Us = 510 N/mm²; for the bolt Ub = 800 N/mm².
Standard holes give kbs=1.0k_{bs}=1.0. For S355 plate the bearing strength is pbs=550 N/mm2p_{bs}=550\ \mathrm{N/mm^{2}} and Us=510 N/mm2U_s=510\ \mathrm{N/mm^{2}}; for the bolt Ub=800 N/mm2U_b=800\ \mathrm{N/mm^{2}}.Yellow: given parameter, row or columnOrange: value read from the table, boxed orange in the text too

Solution Route: Substitute into four expressions separately→compare in consistent units→take the minimum→compare with per-bolt demand.

Load path · the stations the force passes through, in order

One bolt presses on the hole wall of the 14 mm plate. The plate can fail in four ways; the smallest of the four capacities is used.

  1. Force per bolt
    About 166.7 kN
  2. Hole wall crushes
    Demand 166.7 kNCapacity 207.9 kN
    Utilisation 0.80 · closest to the limit
  3. Tear-out at the plate end
    Demand 166.7 kNCapacity 269.5 kN
    Utilisation 0.62
  4. Tearing between holes
    Demand 166.7 kNCapacity 535.5 kN
    Utilisation 0.31
  5. Cap from the bolt strength
    Demand 166.7 kNCapacity 604.8 kN
    Utilisation 0.28
Red frame: the station closest to its limit. Each station links to the step that calculates it.
  1. Step 1 · Hole-wall term

    Why this step: The bolt presses on the hole wall over an area of bolt diameter times plate thickness. This term guards against the wall being crushed and the hole stretching.

    dd is the 27 mm bolt diameter; tpt_p is this 14 mm plate's thickness.

    New symbols in this step
    • kbsk_{bs}, KeK_e: Hole-type and effective-area factors; dimensionless
    P1=kbsdtppbs=1.0(27)(14)(550)/1000=207.9 kNP_1=k_{bs}dt_pp_{bs}={\htmlClass{read}{1.0}}({\htmlClass{given}{27}})({\htmlClass{given}{14}})({\htmlClass{read}{550}})/1000=207.9\ \mathrm{kN}
    P1=kbsdtppbs=1.0(27)(14)(550)/1000=207.9 kN\begin{aligned}P_1&=k_{bs}dt_pp_{bs}\\&={\htmlClass{read}{1.0}}({\htmlClass{given}{27}})({\htmlClass{given}{14}})({\htmlClass{read}{550}})/1000\\&=207.9\ \mathrm{kN}\end{aligned}

    Units: dd and tpt_p are in mm and pbsp_{bs} is in N/mm², so the product is in N; dividing by 1000 gives kN.

    ▶ The lecturer on this part: 14 November 01:04:23

  2. Step 2 · End-distance term

    Why this step: If the hole is too near the plate end, the bolt can push out the short piece of steel behind the hole. A longer end distance gives this term more capacity.

    e=70 mme=70\ \mathrm{mm} is measured along the force, not transversely to the edge.

    P2=0.5kbsetppbs=0.5(1.0)(70)(14)(550)/1000=269.5 kNP_2=0.5k_{bs}et_pp_{bs}=0.5({\htmlClass{read}{1.0}})({\htmlClass{given}{70}})({\htmlClass{given}{14}})({\htmlClass{read}{550}})/1000=269.5\ \mathrm{kN}
    P2=0.5kbsetppbs=0.5(1.0)(70)(14)(550)/1000=269.5 kN\begin{aligned}P_2&=0.5k_{bs}et_pp_{bs}\\&=0.5({\htmlClass{read}{1.0}})({\htmlClass{given}{70}})({\htmlClass{given}{14}})({\htmlClass{read}{550}})/1000\\&=269.5\ \mathrm{kN}\end{aligned}

    Units: ee and tpt_p are in mm and pbsp_{bs} is in N/mm², so the product is in N; dividing by 1000 gives kN.

  3. Step 3 · Clear-distance term

    Why this step: This term guards against the bolt tearing through the steel left between two holes. The wider the holes are spaced, the more steel there is and the harder it is to tear.

    Use le=50 mml_e=50\ \mathrm{mm} with plate Us=510U_s=510.

    New symbols in this step
    • dd, d0d_0, ee, lel_e: Bolt diameter, hole diameter, end distance along force and clear hole spacing; mm
    P3=1.5letpUs=1.5(50)(14)(510)/1000=535.5 kNP_3=1.5l_et_pU_s=1.5({\htmlClass{given}{50}})({\htmlClass{given}{14}})({\htmlClass{read}{510}})/1000=535.5\ \mathrm{kN}
    P3=1.5letpUs=1.5(50)(14)(510)/1000=535.5 kN\begin{aligned}P_3&=1.5l_et_pU_s\\&=1.5({\htmlClass{given}{50}})({\htmlClass{given}{14}})({\htmlClass{read}{510}})/1000\\&=535.5\ \mathrm{kN}\end{aligned}

    Units: lel_e and tpt_p are in mm and UsU_s is in N/mm², so the product is in N; dividing by 1000 gives kN.

  4. Step 4 · Bolt-strength cap

    Why this step: However strong the plate is, the bearing force passed to it cannot exceed a ceiling tied to the bolt strength. This term is that ceiling.

    The final expression uses Ub=800U_b=800, not Us=510U_s=510 again.

    P4=2.0dtpUb=2.0(27)(14)(800)/1000=604.8 kNP_4=2.0dt_pU_b=2.0({\htmlClass{given}{27}})({\htmlClass{given}{14}})({\htmlClass{read}{800}})/1000=604.8\ \mathrm{kN}
    P4=2.0dtpUb=2.0(27)(14)(800)/1000=604.8 kN\begin{aligned}P_4&=2.0dt_pU_b\\&=2.0({\htmlClass{given}{27}})({\htmlClass{given}{14}})({\htmlClass{read}{800}})/1000\\&=604.8\ \mathrm{kN}\end{aligned}

    Units: dd and tpt_p are in mm and UbU_b is in N/mm², so the product is in N; dividing by 1000 gives kN.

  5. Step 5 · Take the governing value

    Why this step: The smallest is the hole-wall term, so crushing of the hole wall would happen first as the force grows. It still exceeds the demand per bolt, so plate bearing is adequate.

    All four bounds must be satisfied, so take the minimum.

    New symbols in this step
    • PsP_s, PbbP_{bb}, PbsP_{bs}, PtP_t: Shear, bolt bearing, plate bearing and plate tension resistances; kN
    Pbs=min⁡(P1, P2, P3, P4)=min⁡(207.9, 269.5, 535.5, 604.8)=207.9 kN>166.7 kNP_{bs}=\min(P_1,\ P_2,\ P_3,\ P_4)=\min(207.9,\ 269.5,\ 535.5,\ 604.8)=207.9\ \mathrm{kN}>{\htmlClass{given}{166.7}}\ \mathrm{kN}
    Pbs=min⁡(P1, P2, P3, P4)=min⁡(207.9, 269.5, 535.5, 604.8)=207.9 kN>166.7 kN\begin{aligned}P_{bs}&=\min(P_1,\ P_2,\ P_3,\ P_4)\\&=\min(207.9,\ 269.5,\ 535.5,\ 604.8)\\&=207.9\ \mathrm{kN}\\&>{\htmlClass{given}{166.7}}\ \mathrm{kN}\end{aligned}

    Where the numbers come from: 207.9207.9 from Step 1; 269.5269.5 from Step 2; 535.5535.5 from Step 3; 604.8604.8 from Step 4.

    Load path · Four limits on plate bearing
    Bolt pushes towards the plate end →d = 27Hole wall crusheskbsdtppbs​= 207.9 kNGoverns (smallest)e = 70End tear-out0.5kbsetppbs​= 269.5 kNle​ = 50Tear between holes1.5letpUs​= 535.5 kNUb​Bolt strength cap2.0dtpUb​= 604.8 kNDemand per bolt about 166.7 kN < Pbs​ = 207.9 kN
    The bolt presses on the hole wall, and the plate can fail in four ways: the hole wall crushes, the bolt tears out through the plate end, the plate tears between two holes, and there is a cap set by the bolt strength. The smallest of the four values is used (red frame).
Conclusion

This calculates bearing for this 14 mm plate only. It is not the full solution to the 7 November 960 kN test or the later 1200 kN past-paper question.

All the symbols of this example

SymbolsMeaning and Units
PsP_s, PbbP_{bb}, PbsP_{bs}, PtP_tShear, bolt bearing, plate bearing and plate tension resistances; kN
dd, d0d_0, ee, lel_eBolt diameter, hole diameter, end distance along force and clear hole spacing; mm
psp_s, pbbp_{bb}, pbsp_{bs}, pyp_yCorresponding course design strengths; N/mm²
UsU_s, UbU_bPlate and bolt ultimate tensile strengths; N/mm²
kbsk_{bs}, KeK_eHole-type and effective-area factors; dimensionless

Video positions: 14 November 01:05:00

↑ Top