Note: marks are as printed in the paper; the working is a teaching guide, not an official marking scheme.
An overhang, not a support at A
The roller is at B and the pin at D. A is a free vertical tip with a lateral-restraint cross; C is another lateral restraint. Coordinates from A are 0, 5, 11 and 15 m. Factored downward loads: 30 kN at A, 40 kN at C, and 2 kN/m only from B to D. Self-weight is negligible. The S355 457 × 191 × 89 UB is given as Class 1.
Simple explanation — open only if needed
The left overhang behaves like a diving board sticking beyond its support. A downward force at its free tip creates hogging at B. The cross at A stops sideways movement; it does not lift the beam up, so there is no vertical reaction at A.
BQ4(a) — support reactions [3 marks]
Take counter-clockwise moments as positive about B. The left-tip force rotates in the opposite sense to loads on the right. The 20 kN UDL resultant is at the midpoint of BD, 5 m to the right of B.
W=2(6+4)=20kN
∑MB=0:10RD+30(5)−40(6)−20(5)=0
RD=10240+100−150=19kN,RB=30+40+20−19=71kN
Check total upward reaction 90 kN against the total downward load 90 kN.
BQ4(b) — annotated SFD and BMD [4 marks]
Choose positive sagging moment. On AB, x is measured from A; on BC, s is measured from B; on CD, t is measured from C. Keep these origins explicit. At B and C the bending moment is continuous, even though shear jumps.
AB:V=−30kN,M=−30xkNm(0≤x≤5)
MB=−30(5)=−150kNm,VB+=−30+71=41kN
BC:V=41−2s,M=−150+41s−s2(0≤s≤6)
VC−=41−2(6)=29kN,MC=−150+41(6)−62=60kNm
VC+=29−40=−11kN
CD:V=−11−2t,M=60−11t−t2(0≤t≤4)
VD−=−11−2(4)=−19kN,MD=60−11(4)−42=0
The BD moment diagram changes sign within BC. Solve the quadratic and choose the root that lies inside the 6 m segment; the other root is outside and has no physical relevance here.
−150+41s−s2=0⇒s=241±412−4(150)
s=241−1081=4.060718mfrom B
Shear is positive throughout BC, so moment increases from −150 to +60; the largest absolute moment is 150 kN·m at B. CD decreases from +60 to zero. AB is a straight negative triangle because it has no UDL.
Calculated SFD/BMD: B is the vertical support at 5 m, the zero-moment point is 4.060718 m right of B. Full-size image
Use the moments at one-quarter, one-half and three-quarters of THIS restrained segment. They are not necessarily at load points. Evaluate the actual quadratic bending diagram including the UDL; use absolute magnitudes in the quarter-point expression and compare with the maximum absolute moment in the segment.
Use millimetres in slenderness. The section table supplies the minor-axis radius of gyration, buckling parameter and torsional index; the given Class 1 section has a plastic-section factor of one. These quantities change when the section changes.
Choose Data File p.5, Table 8.3, 345 N/mm² column. Interpolate between the two surrounding slenderness rows in the same design-strength column; do not mix columns.
Buckling strength times plastic modulus gives moment resistance. Convert the tabulated cubic centimetres to cubic millimetres, then newton-millimetres to kilonewton-metres.
AB is a cantilever segment without an intermediate lateral restraint. The course cantilever moment-factor rule is mLT = 1, even though its bending diagram is triangular. The simply supported end-moment factor is not applicable.
mLT=1,∣Mmax∣=150kNm,mLT∣Mmax∣=150kNm
Course Table 8.1: cantilever effective length. Read support row, tip condition and loading column together. Full-size image
Branch 1: continuous support with lateral AND torsional restraint (row c), tip lateral restraint to top flange (tip 2), NORMAL loading. Table value 0.9L gives 4,500 mm.
LE=0.9(5000)=4500mm
Use millimetres in slenderness. The section table supplies the minor-axis radius of gyration, buckling parameter and torsional index; the given Class 1 section has a plastic-section factor of one. These quantities change when the section changes.
Choose Data File p.5, Table 8.3, 345 N/mm² column. Interpolate between the two surrounding slenderness rows in the same design-strength column; do not mix columns.
Buckling strength times plastic modulus gives moment resistance. Convert the tabulated cubic centimetres to cubic millimetres, then newton-millimetres to kilonewton-metres.
The stated effective-length model passes this LTB check.
Branch 2: continuous support with lateral restraint to top flange only (row a), the same tip condition 2 and NORMAL loading. Table value 2.7L gives 13,500 mm.
LE=2.7(5000)=13500mm
Use millimetres in slenderness. The section table supplies the minor-axis radius of gyration, buckling parameter and torsional index; the given Class 1 section has a plastic-section factor of one. These quantities change when the section changes.
Choose Data File p.5, Table 8.3, 345 N/mm² column. Interpolate between the two surrounding slenderness rows in the same design-strength column; do not mix columns.
Buckling strength times plastic modulus gives moment resistance. Convert the tabulated cubic centimetres to cubic millimetres, then newton-millimetres to kilonewton-metres.
The stated effective-length model fails this LTB check.
One case passes and the other fails. So in the exam, write which row and column of Table 8.1 you chose and why — do not just write “passes”. If the load is destabilizing, use that column of the table and recalculate.
BC passes its stated branch. AB needs the cantilever restraint/loading conditions before a unique pass/fail decision; show the chosen conditional branch.
Common mistakes
Do not put a vertical reaction at A.
Do not extend the UDL onto AB.
A triangular cantilever diagram does not justify the simple-span mLT formula.
Procedure for a new variant
Mark actual vertical supports and the loaded length.
Solve reactions, signed diagrams and any contraflexure point.
For each segment choose the correct beam/cantilever model and restraints.
Calculate table-based LTB and state unresolved conditions.
Independent self-check — invented variant
Invented variant: the 30 kN load at A is removed. Find the new reactions and moment at B.
Hint
Repeat moment equilibrium about B.
Answer and reasoning
RD=[40(6)+20(5)]/10=34kN,RB=60−34=26kN,MB=0
An unloaded free overhang carries no bending moment in this idealized model. The reactions change even though the support locations do not.