Steelwork · Exam learning

2022–2024 · Exam-focused route

2023 BQ3 — column with biaxial bending

All answers shown

Complete the axial-force, section and member checks, following this paper’s moment model.

Original source: 22ENGTY006.pdf · physical page 5

Marks are as printed in the paper; the working is a teaching guide, not an official marking scheme.

Choose the column model first

An eccentric beam reaction bends the column

A simple beam joint delivers a vertical reaction away from the column centre. Find the resulting column moments.

The reaction arrow is offset by e from the column centre. The upper and lower arrows show where the joint moment is shared.
The reaction arrow is offset by e from the column centre. The upper and lower arrows show where the joint moment is shared.

Prediction, then explanation. Equal opposite-face reactions can cancel a joint moment. Their downward forces still add to column compression.

Sum axial forces first. Calculate the signed eccentric moments. Share the net joint moment between upper and lower columns using the stated stiffness model.

M=Re,Mlower=MKlowerKupper+KlowerM=Re,\qquad M_{lower}=M\frac{K_{lower}}{K_{upper}+K_{lower}}

R is reaction; e is perpendicular eccentricity. K denotes the stiffness measure prescribed for moment sharing.

Scope. Equal sharing requires equal stated stiffness. Use actual storey length where the special simple-construction LTB rule requires it.

Check and takeaway. A pin-like beam connection can still cause an eccentric reaction moment in the column. Joint rotation and reaction location are separate facts.

Restraints define the analysis model

Choose an analysis model that represents the actual joints, restraints and possible sway.

Braced pathPossible sway
The joint symbol describes permitted rotation. The frame arrows describe possible sideways movement. These are separate observations.

Prediction, then explanation. A joint that permits beam rotation does not automatically remove all column moment. Eccentric reactions may still bend the column.

First identify the joint behaviour. Next identify how horizontal forces reach the foundations. Then assess sway sensitivity using the course criterion.

Simple, continuous and semi-continuous construction describe joint modelling. Sway classification describes overall frame response.

Scope. The schematic does not establish restraint stiffness or a stability threshold. Use the stated data and classification rules.

Check and takeaway. An ideal straight frame may still require notional horizontal forces to represent imperfections under the applicable method.

Moment shape matters within one segment

Represent a nonuniform moment distribution in the applicable member-buckling equation.

The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.
The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.

Prediction, then explanation. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Evaluate moments from the true whole-beam analysis at the required positions. Apply the exact table’s weights, signs and lower bound.

mLT is an LTB factor. mx and my belong to the specified flexural checks. They are not interchangeable.

Scope. Some rules use magnitudes; others require signed ordinates. A factor does not reduce the actual moment used in a local section check.

Check and takeaway. Measure quarter points from the segment start, not automatically from the beam’s left support.

Apply the reasoning to this section’s data and conditions

Both papers use 305 × 305 × 158 UC, but they do not give the moments in the same way.

In 2022, signed end moments are supplied.

Use the continuous non-sway branch conditionally.

In 2023, eccentric beam reactions act at a joint.

Use the course simple-construction model, share the joint moment by stiffness, and use the explicitly given moment factors.

Physical interpretation and limits

A short steel block may survive squeezing while a long ruler with the same cross-section bends sideways.

The section check asks whether the steel at one slice is strong enough.

The member checks also ask whether the whole column can buckle.

Passing one does not replace the others.

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.1, p.11
Ag=201 cm2=20100 mm2,rx=13.9 cm=139 mm,ry=7.90 cm=79 mmA_g=201\,\mathrm{cm^2}=20100\,\mathrm{mm^2},\quad r_x=13.9\,\mathrm{cm}=139\,\mathrm{mm},\quad r_y=7.90\,\mathrm{cm}=79\,\mathrm{mm}
Zx=2369, Zy=808, Sx=2680, Sy=1230[cm3]Z_x=2369,\ Z_y=808,\ S_x=2680,\ S_y=1230\quad[\mathrm{cm^3}]
T=25 mm, t=15.8 mm, b/T=6.22, d/t=15.6,u=0.851,x=12.5T=25\,\mathrm{mm},\ t=15.8\,\mathrm{mm},\ b/T=6.22,\ d/t=15.6,\quad u=0.851,\quad x=12.5

These are lookups from the exact UC row.

The flange thickness selects the S355 design strength 345 N/mm².

A is area, r radius of gyration, Z elastic modulus, S plastic modulus, T flange thickness and t web thickness. u and x are the LTB section parameters, not geometric coordinates.

BQ3(a) — axial force and moments [3 marks]

Compression acts on the displaced shape

A compressed member moves away from its initial load line. Explain why the bending moment can increase.

The dashed line labelled Original marks the initial position. The tilted member creates the extra horizontal lever arm shown below.
The dashed line labelled Original marks the initial position. The tilted member creates the extra horizontal lever arm shown below.

Prediction, then explanation. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Force acting through an offset forms a moment. Second-order analysis includes that changed geometry in equilibrium.

Madditional=PΔorPδM_{additional}=P\Delta\quad\text{or}\quad P\delta

P is axial force. Δ and δ are the relevant perpendicular displacements. Consistent force and length units give moment units.

Scope. Use the amplification or analysis method stated for the frame. Do not amplify an already amplified moment a second time.

Check and takeaway. Zero offset removes this additional moment in the ideal sketch. Real design may still require imperfections and code checks.

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Check buckling about both axes

Determine which buckling direction limits the compressed member.

Compare the outlines labelled Straight and Bowed. The dashed line beside Bowed marks its original straight reference.
Compare the outlines labelled Straight and Bowed. The dashed line beside Bowed marks its original straight reference.

Prediction, then explanation. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Calculate slenderness about each axis. Select each axis’s curve from section type and thickness. Then obtain and compare the two compressive resistances.

λx=LEx/rx,λy=LEy/ry,Pc=pcAg\lambda_x=L_{Ex}/r_x,\quad\lambda_y=L_{Ey}/r_y,\qquad P_c=p_cA_g

Effective lengths and radii use mm. pc is compressive strength in N/mm²; Ag is gross area in mm²; Pc is in N.

Scope. Do not select the governing axis using radius alone. Effective length and buckling curve can differ. A combined column also needs interaction checks.

Check and takeaway. A short-section yield resistance is not the same as long-member buckling resistance. Keep py and pc distinct.

Apply the reasoning to this section’s data and conditions

Given: central load 3,150 kN including self-weight.

A 200 kN reaction at the left 200 mm offset, 700 kN above the centre at 240 mm and 450 kN below at 220 mm; all are already factored.

Actual column height is 4.5 m; effective length is 4.0 m in both directions.

Grade S355 and Class 1 are given.

Upper and lower columns have equal stiffness; all moment factors are one and amplification is 1.1.

N=3150+200+700+450=4500 kNN=3150+200+700+450=4500\,\mathrm{kN}

The top and bottom reactions rotate about x in opposite senses, so subtract their moment contributions.

The left reaction contributes about y.

Convert millimetres to metres for kN·m.

Mx,joint=700(0.240)−450(0.220)=168−99=69 kN mM_{x,joint}=700(0.240)-450(0.220)=168-99=69\,\mathrm{kN\,m}
∣My,joint∣=200(0.200)=40 kN m|M_{y,joint}|=200(0.200)=40\,\mathrm{kN\,m}

Joint moment is shared in proportion to column stiffness.

Equal upper/lower stiffness gives one half to the column under consideration.

The axial force is not halved: the lower column carries the sum of the incoming vertical loads.

η=KlowerKupper+Klower=KK+K=12\eta=\frac{K_{lower}}{K_{upper}+K_{lower}}=\frac{K}{K+K}=\frac12
Mx=69/2=34.5 kN m,My=40/2=20 kN mM_x=69/2=34.5\,\mathrm{kN\,m},\quad M_y=40/2=20\,\mathrm{kN\,m}
M^x=1.1(34.5)=37.95 kN m,M^y=1.1(20)=22 kN m,MLT=37.95 kN m\widehat M_x=1.1(34.5)=37.95\,\mathrm{kN\,m},\quad\widehat M_y=1.1(20)=22\,\mathrm{kN\,m},\quad M_{LT}=37.95\,\mathrm{kN\,m}

BQ3(b) — cross-section capacity [8 marks]

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Apply the reasoning to this section’s data and conditions

Source: LectureNotes/Ch4_Column.pdf · p.14, p.20

The cross-section check combines axial compression and two bending components at one section.

Use amplified moments, gross compression resistance and the Class 1 capped plastic bending resistances.

Every ratio must be dimensionless.

NRd=Agpy/1000=20100(345)/1000=6934.5 kNN_{Rd}=A_gp_y/1000=20100(345)/1000=6934.5\,\mathrm{kN}
Mcx=min⁡(345(2680),1.2(345)(2369))/1000=min⁡(924.6,980.766)=924.6 kN mM_{cx}=\min(345(2680),1.2(345)(2369))/1000=\min(924.6,980.766)=924.6\,\mathrm{kN\,m}
Mcy=min⁡(345(1230),1.2(345)(808))/1000=min⁡(424.35,334.512)=334.512 kN mM_{cy}=\min(345(1230),1.2(345)(808))/1000=\min(424.35,334.512)=334.512\,\mathrm{kN\,m}
NAgpy+M^xMcx+M^yMcy=45006934.5+37.95924.6+22334.512=0.755741≤1\frac{N}{A_gp_y}+\frac{\widehat M_x}{M_{cx}}+\frac{\widehat M_y}{M_{cy}}=\frac{4500}{6934.5}+\frac{37.95}{924.6}+\frac{22}{334.512}=0.755741\le1

The section passes this branch.

The minor-axis elastic cap controls; using the uncapped plastic value there would overstate resistance.

BQ3(c) — member buckling [19 marks]

A strong cross-section can belong to an unstable member

A column carries axial compression and bending. Explain why more than one check is required.

The three boxes name separate checks: Section, Flexural and LTB. The bottom caption explains that passing one does not pass the others.
The three boxes name separate checks: Section, Flexural and LTB. The bottom caption explains that passing one does not pass the others.

Prediction, then explanation. At fixed moments and resistances, increasing compression increases utilisation. A section pass cannot remove the length-dependent instability checks.

Separate cross-section, flexural-buckling and LTB interaction equations. Use each equation’s own denominators and first-order or amplified moments.

AgpyA_g p_y is a section axial resistance. AgpcA_g p_c is a member compression resistance. Elastic pyZp_y Z and prescribed McM_c are different bending denominators.

Scope. Preserve the course barred-moment definitions and Eq. 8.81 convention. Do not substitute plastic moduli into an elastic denominator.

Check and takeaway. Report each requested utilisation and the governing check. The largest properly calculated ratio identifies the closest limit.

Apply the reasoning to this section’s data and conditions

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.7, p.8

For the rolled UC with flange thickness below 40 mm, choose strut curve b about x and curve c about y.

Effective length divided by the corresponding radius gives slenderness.

Use the 345 N/mm² column of each curve’s compression-strength table.

λx=LEx/rx=4000/139=28.776978,λy=LEy/ry=4000/79=50.632911\lambda_x=L_{Ex}/r_x=4000/139=28.776978,\quad\lambda_y=L_{Ey}/r_y=4000/79=50.632911

Choose Data File p.8, curve b.

Interpolate between the two surrounding slenderness rows in the same design-strength column.

Do not mix columns.

pcx=332+28.776978−2530−25(325−332)=326.71223  N/mm2p_{cx}=332+\frac{28.776978-25}{30-25}(325-332)=326.71223\;\mathrm{N/mm^2}

Choose Data File p.8, curve c.

Interpolate between the two surrounding slenderness rows in the same design-strength column.

Do not mix columns.

pcy=268+50.632911−5052−50(263−268)=266.417722  N/mm2p_{cy}=268+\frac{50.632911-50}{52-50}(263-268)=266.417722\;\mathrm{N/mm^2}
Pcx=Agpcx/1000=20100(326.71223)/1000=6566.915827 kNP_{cx}=A_gp_{cx}/1000=20100(326.71223)/1000=6566.915827\,\mathrm{kN}
Pcy=20100(266.417722)/1000=5354.996203 kNP_{cy}=20100(266.417722)/1000=5354.996203\,\mathrm{kN}
Pc=min⁡(Pcx,Pcy)=5354.996203 kNP_c=\min(P_{cx},P_{cy})=5354.996203\,\mathrm{kN}
Source: LectureNotes/Ch4_Column.pdf · p.19, p.20

All three moment factors are given as one.

The simple-construction LTB rule uses half the ACTUAL column height divided by the minor-axis radius.

The 4,000 mm effective length belongs to compression slenderness, not this rule.

mx=my=mLT=1,λLT=0.5L/ry=0.5(4500)/79=28.481013m_x=m_y=m_{LT}=1,\quad\lambda_{LT}=0.5L/r_y=0.5(4500)/79=28.481013
Source: LectureNotes/CON4334-Data File-20260730.pdf · p.5

Choose Data File p.5, Table 8.3, 345 N/mm² column.

Interpolate between the two surrounding slenderness rows in the same design-strength column.

Do not mix columns.

pb=345+28.481013−2530−25(345−345)=345  N/mm2p_b=345+\frac{28.481013-25}{30-25}(345-345)=345\;\mathrm{N/mm^2}
Mb=pbSx/1000=345(2680)/1000=924.6 kN mM_b=p_bS_x/1000=345(2680)/1000=924.6\,\mathrm{kN\,m}
Source: LectureNotes/Ch4_Column.pdf · p.20

For the member interaction equations, the course uses ELASTIC section bending resistances.

These are different from the capped plastic resistances used in the section check.

The first member equation uses the smaller compression resistance and amplified moments.

Mex=pyZx/1000=345(2369)/1000=817.305 kN mM_{ex}=p_yZ_x/1000=345(2369)/1000=817.305\,\mathrm{kN\,m}
Mey=pyZy/1000=345(808)/1000=278.76 kN mM_{ey}=p_yZ_y/1000=345(808)/1000=278.76\,\mathrm{kN\,m}
ηflex=NPc+mxM^xMex+myM^yMey\eta_{flex}=\frac{N}{P_c}+\frac{m_x\widehat M_x}{M_{ex}}+\frac{m_y\widehat M_y}{M_{ey}}
ηflex=45005354.996203+1(37.95)817.305+1(22)278.76=0.965691≤1\eta_{flex}=\frac{4500}{5354.996203}+\frac{1(37.95)}{817.305}+\frac{1(22)}{278.76}=0.965691\le1

The second member equation combines minor-axis compression buckling with major-axis LTB.

It uses MLT as stated above and the first-order minor-axis moment (the barred moment in the course summary).

Do not insert the amplified minor-axis moment again.

ηLT=NPcy+mLTMLTMb+myM‾yMey\eta_{LT}=\frac{N}{P_{cy}}+\frac{m_{LT}M_{LT}}{M_b}+\frac{m_y\overline M_y}{M_{ey}}
ηLT=45005354.996203+1(37.95)924.6+1(20)278.76=0.953128≤1\eta_{LT}=\frac{4500}{5354.996203}+\frac{1(37.95)}{924.6}+\frac{1(20)}{278.76}=0.953128\le1

Both member equations pass in the stated branch.

Retain the source qualification.

A numerical pass cannot remove a missing or contradictory input.

Result and concise exam wording

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Apply the reasoning to this section’s data and conditions

Concise exam wording

N=4500 kN,M^x=37.95 kN m,M^y=22 kN mN=4500\,\mathrm{kN},\quad\widehat M_x=37.95\,\mathrm{kN\,m},\quad\widehat M_y=22\,\mathrm{kN\,m}
ηsection=0.755741,ηflex=0.965691,ηLT=0.953128\eta_{section}=0.755741,\quad\eta_{flex}=0.965691,\quad\eta_{LT}=0.953128

All are below one under the stated interpretation.

Give the table brackets, moment factors and source qualification in the script.

Misconceptions and checks

Vertical bending can trigger sideways motion

A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.

The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.
The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.

Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.

λ=LE/ry,Mb=pbSx  (Class 1/2),mLTMmax≤Mb\lambda=L_E/r_y,\qquad M_b=p_bS_x\;\text{(Class 1/2)},\qquad m_{LT}M_{max}\le M_b

LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.

Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.

Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.

Use the same mechanism: Check buckling about both axes. At fixed radius, longer effective length raises slenderness. The supplied buckling curve generally gives lower compressive strength.

Use the property for the physical question

A section table contains several numbers. Choose the property that matches the calculation and bending axis.

Read the three labels beside the I-section: I describes geometric stiffness, Z elastic section modulus and S plastic section modulus.
Read the three labels beside the I-section: I describes geometric stiffness, Z elastic section modulus and S plastic section modulus.

Prediction, then explanation. Moving equal area away from an axis increases I about that axis. It does not increase total area.

Each small area contributes its area multiplied by squared distance. Sum those contributions to obtain I.

I=∫y2 dA,r=I/AI=\int y^2\,dA,\qquad r=\sqrt{I/A}

I is second moment of area in mm⁴. y is distance from the chosen axis in mm. A is area in mm². r is radius of gyration in mm.

Scope. Z is elastic section modulus; S is plastic section modulus in this course. Neither is interchangeable with I.

Check and takeaway. A nominal section designation is a row identifier. Use the actual dimensions and units in that exact row.

Apply the reasoning to this section’s data and conditions

  • Never interchange elastic and plastic modulus denominators between section and member checks.
  • Only joint moment is shared between upper/lower columns; axial load is not halved.
  • For the 2023 simple model, LTB uses 4.5 m actual height, compression uses 4.0 m effective length.

Procedure for a new variant

Use the same mechanism: Compression acts on the displaced shape. At fixed axial force, a larger offset creates a larger additional moment. This can further increase the displacement.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

A force couple carries moment

Separate the force couple used to carry moment from the force used to carry web shear.

The flange forces act in opposite directions. Their separation z gives the lever arm. The web arrow represents shear.
The flange forces act in opposite directions. Their separation z gives the lever arm. The web arrow represents shear.

Prediction, then explanation. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Moment is force multiplied by perpendicular separation. Divide the required moment by the specified separation to obtain each couple force.

F=M/zF=M/z

M is moment in kN·mm; z is the specified force-line separation in mm; F is force in kN.

Scope. Use the lever arm defined by the source model. Do not silently replace it with overall section depth or another geometric distance.

Check and takeaway. Check flange welds for the couple forces and web welds for the stated shear model. Both force paths need a satisfactory detail.

Apply the reasoning to this section’s data and conditions

  1. Determine the construction model, axes and signs.
  2. Separate first-order, amplified and LTB moments.
  3. Look up both strut curves and the applicable LTB strength.
  4. Perform section and both member equations; state conditions.

Prediction with explained answer — invented variant

Two simultaneous actions use one component

Check a component that carries shear and tension, or compression and bending, at the same time.

The bolt receives two labelled arrows: tension and shear. The caption requires both individual checks and the combined check.
The bolt receives two labelled arrows: tension and shear. The caption requires both individual checks and the combined check.

Prediction, then explanation. At fixed resistances, increasing one demand increases its utilisation. The permitted sum is not always one.

First apply the individual checks. Next use the exact combined equation and its definitions. Keep demands from the same load case.

FsPs+FtPnom≤1.4\frac{F_s}{P_s}+\frac{F_t}{P_{nom}}\le1.4

This is the course bolt interaction rule. Fs and Ft are bolt demands; Ps and Pnom are their specified resistance denominators.

Scope. The 1.4 limit and nominal tension denominator do not apply to column equations. Their limits and moment definitions are separate.

Check and takeaway. A sum above one can pass this bolt rule while still needing individual checks. A pass must name the actual equation used.

Apply the reasoning to this section’s data and conditions

Invented variant: in the 2023 joint, the lower column is twice as stiff as the upper.

What changes before any strength check?

Hint

Use lower stiffness divided by total stiffness.

Answer and reasoning

η=2/(1+2)=2/3,Mx=69(2/3)=46,My=40(2/3)=26.666667[kN m]\eta=2/(1+2)=2/3,\quad M_x=69(2/3)=46,\quad M_y=40(2/3)=26.666667\quad[\mathrm{kN\,m}]
M^x=50.6,M^y=29.333333[kN m],N=4500 kN\widehat M_x=50.6,\quad\widehat M_y=29.333333\quad[\mathrm{kN\,m}],\quad N=4500\,\mathrm{kN}

All interaction ratios must be recalculated.

The load share is based on stiffness; equal halves would now be wrong.