Steelwork · Exam learning

2022–2024 · Exam-focused route

2023 FT/PTD BQ2(a) — double bolted angles

All answers shown

Solve all four strength checks; distinguish angle-pair action from a single-angle example.

Original source: 22ENGTY006.pdf · physical page 3

Marks are as printed in the paper; the working is a teaching guide, not an official marking scheme.

Read the double-angle connection

Count cuts through each loaded bolt

Find how many shear planes transfer the force through one side of the connection.

The middle plate moves against two cover plates. The two interfaces cut each bolt at two planes.
The middle plate moves against two cover plates. The two interfaces cut each bolt at two planes.

Prediction, then explanation. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Select the area at the actual shear plane. Multiply by bolt shear strength. Count only the bolts and planes in the same transfer stage.

Ps=psAs,Pgroup=nbnsPsP_s=p_sA_s,\qquad P_{group}=n_b n_s P_s

ps is bolt shear strength in N/mm²; As is the appropriate area in mm². nb counts bolts; ns counts equally loaded shear planes.

Scope. Use the thread area when threads cross the plane as required. Check bearing, plate failure and detailing separately.

Check and takeaway. Both halves of a butt splice carry the full transmitted force in sequence. Counting both halves together would double the apparent resistance.

Follow contact pressure into the plate

The bolt may survive shear while the connected plate deforms or tears near the hole.

The labels distinguish bolt diameter d from hole diameter d₀. The arrow at the hole edge shows the bearing contact action.
The labels distinguish bolt diameter d from hole diameter d₀. The arrow at the hole edge shows the bearing contact action.

Prediction, then explanation. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

Calculate every bound required by the supplied rule. The smallest applicable bound limits the connection at that layer.

Pbearing≤pbsdtP_{bearing}\le p_{bs}dt

pbs is the applicable bearing strength in N/mm²; d is nominal bolt diameter in mm; t is plate thickness in mm.

Scope. This diameter term alone is not the complete check. End-distance and clear-ligament limits, bolt bearing and each connected layer also matter.

Check and takeaway. Two covers and one main plate do not necessarily have the same thickness or strength. Compare the actual force share in each layer.

Test every possible fracture cut

Find the remaining steel area across a candidate tension-failure path.

The dashed fracture line crosses two hole centres. Subtract only the holes crossed by that candidate line.
The dashed fracture line crosses two hole centres. Subtract only the holes crossed by that candidate line.

Prediction, then explanation. At fixed plate size, larger holes reduce the straight-path net area. A diagonal path needs its own stagger correction.

Subtract the hole widths crossed by the path, then multiply by thickness. Compare all plausible paths using the applicable course rule.

An=(b−nd0)tA_n=(b-nd_0)t

An is net area in mm²; b is plate width; d₀ is hole diameter; t is thickness, all in mm. n counts holes on this straight path.

Scope. This expression is for a straight cut. Effective area can require further shear-lag rules. Gross, net and effective areas must remain distinct.

Check and takeaway. Use the hole diameter, not the bolt diameter, when removing missing steel. The plate contains a hole, not solid steel around the bolt shank.

Apply the reasoning to this section’s data and conditions

Given: two 200 × 100 × 10 unequal angles, one each side of a 20 mm gusset; four M27 Grade 8.8 bolts in 30 mm holes; S355; 1,050 kN concentric ultimate tension.

Gusset strength is explicitly excluded.

The front view has two longitudinal columns at 80 mm pitch, 50 mm end distance, and two transverse rows at 80 mm gauge with 60 mm edge distances.

Section A–A confirms two shear interfaces, not eight physical bolts.

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.4
Source: LectureNotes/Ch2_Connection.pdf · p.10, p.11, p.14, p.17

Lookups: Data File p.4, M27 tensile-stress-area row and ISO 8.8 strength row.

Use thread area conservatively because a thread-free shear plane is not specified.

For S355 plate bearing use 550 N/mm² and ultimate parent-metal strength 510 N/mm²; bolt ultimate strength is 800 N/mm².

Ordinary 30 mm holes for M27 give the standard-hole factor one.

d=27 mm, d0=30 mm, As=459 mm2, kbs=1, Ke=1.1d=27\,\mathrm{mm},\ d_0=30\,\mathrm{mm},\ A_s=459\,\mathrm{mm^2},\ k_{bs}=1,\ K_e=1.1
ps=375,pbb=1000,pbs=550,Us=510,Ub=800[N/mm2]p_s=375,\quad p_{bb}=1000,\quad p_{bs}=550,\quad U_s=510,\quad U_b=800\quad[\mathrm{N/mm^2}]

Symbols: d is bolt diameter; d₀ hole diameter; Aₛ bolt stress area; pₛ shear strength; pbb bolt bearing strength; pbs connected-part bearing strength; Ke net-area coefficient.

Subtract d₀ from metal width, but use d in bearing resistance.

Stress × mm² gives N; divide by 1,000 for kN.

Physical interpretation and limits

Each angle pulls with half the total load.

A bolt passes through angle–gusset–angle and can shear at both interfaces.

The net angle section cuts across the two transverse bolt rows, so two holes are removed from each connected leg.

BQ2(a)(i) — double-shear bolts [2 marks]

Use the same mechanism: Count cuts through each loaded bolt. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Apply the reasoning to this section’s data and conditions

Pangle=1050/2=525 kNP_{angle}=1050/2=525\,\mathrm{kN}
Ps,one=2(459)(375)/1000=344.25 kNP_{s,one}=2(459)(375)/1000=344.25\,\mathrm{kN}
Ps,group=4(344.25)=1377 kN>1050 kNP_{s,group}=4(344.25)=1377\,\mathrm{kN}>1050\,\mathrm{kN}

BQ2(a)(ii) — bolt bearing [2 marks]

Use the same mechanism: Follow contact pressure into the plate. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

Apply the reasoning to this section’s data and conditions

tp=min⁡(20,10+10)=20 mmt_p=\min(20,10+10)=20\,\mathrm{mm}
Pbb,group=4(27)(20)(1000)/1000=2160 kN>1050 kNP_{bb,group}=4(27)(20)(1000)/1000=2160\,\mathrm{kN}>1050\,\mathrm{kN}

This checks bolt bearing against the total load.

It does not reintroduce the excluded gusset-plate strength calculation.

BQ2(a)(iii) — angle bearing [6 marks]

Use the same mechanism: Follow contact pressure into the plate. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

A bolt diameter is not a hole diameter

Check that bolts fit and leave enough material between holes and plate boundaries.

pdd₀Clear ligament
The inner circle represents bolt diameter d. The outer circle represents hole diameter d₀. Pitch and gauge join hole centres.

Prediction, then explanation. At fixed pitch, a larger hole leaves a shorter clear ligament. Increasing bolt diameter may also increase minimum edge-distance requirements.

Measure pitch along the bolt line and gauge across lines. Distinguish end distance along the load from edge distance across it.

lc=p−d0l_c=p-d_0

lc is clear ligament between holes; p is centre-to-centre pitch; d₀ is hole diameter. All use mm.

Scope. Apply the supplied edge-preparation and minimum/maximum spacing rules. Passing a bearing calculation does not prove the layout passes.

Check and takeaway. For pitch 60 mm and hole diameter 22 mm, the ligament is 38 mm. Using a 20 mm bolt diameter here gives the wrong ligament.

Apply the reasoning to this section’s data and conditions

The end distance is measured parallel to the force, from the free end to the nearest bolt centre.

The clear inter-hole ligament is pitch minus one hole diameter.

Use the smallest applicable bound; using the end-bolt bound for every bolt is conservative for the interior bolts.

t=10 mm, e=50 mm, p=80 mm, lc=p−d0=80−30=50 mmt=10\,\mathrm{mm},\ e=50\,\mathrm{mm},\ p=80\,\mathrm{mm},\ l_c=p-d_0=80-30=50\,\mathrm{mm}
B1=kbsdtpbs1000=1(27)(10)(550)1000=148.5 kNB_1=\frac{k_{bs}dtp_{bs}}{1000}=\frac{1(27)(10)(550)}{1000}=148.5\,\mathrm{kN}
B2=0.5kbsetpbs1000=0.5(1)(50)(10)(550)1000=137.5 kNB_2=\frac{0.5k_{bs}etp_{bs}}{1000}=\frac{0.5(1)(50)(10)(550)}{1000}=137.5\,\mathrm{kN}
B3=1.5lctUs1000=1.5(50)(10)(510)1000=382.5 kNB_3=\frac{1.5l_ctU_s}{1000}=\frac{1.5(50)(10)(510)}{1000}=382.5\,\mathrm{kN}
B4=2dtUb1000=2(27)(10)(800)1000=432 kNB_4=\frac{2dtU_b}{1000}=\frac{2(27)(10)(800)}{1000}=432\,\mathrm{kN}
Pbs,one=min⁡(B1,B2,B3,B4)=137.5 kNP_{bs,one}=\min(B_1,B_2,B_3,B_4)=137.5\,\mathrm{kN}
Pbs,one angle=4(137.5)=550 kN>525 kNP_{bs,one\ angle}=4(137.5)=550\,\mathrm{kN}>525\,\mathrm{kN}
Pbs,two angles=1100 kN>1050 kNP_{bs,two\ angles}=1100\,\mathrm{kN}>1050\,\mathrm{kN}

BQ2(a)(iv) — double-angle tension [7 marks]

One connected leg does not load both legs equally

An angle carries tension through only one leg. Determine how much section area the design rule permits.

The force enters the connected leg first. The outstanding leg receives force through the angle corner and adjoining material.
The force enters the connected leg first. The outstanding leg receives force through the angle corner and adjoining material.

Prediction, then explanation. Keeping the same gross area does not guarantee the same tension resistance when the connection arrangement changes.

Separate connected and outstanding leg areas. Include the actual holes. Then use the supplied single-angle or double-angle effective-area rule.

Pt=pyAeP_t=p_yA_e

Ae is the effective area from the applicable angle rule in mm². py is the relevant design strength in N/mm².

Scope. Do not assume the whole gross area is effective. Symmetry, connected leg and connection type determine which rule applies.

Check and takeaway. The outstanding leg contributes through load transfer; the rule need not either count all of it or discard all of it.

Apply the reasoning to this section’s data and conditions

Follow the lecturer’s rectangular half-heel allocation (Chapter 2 example 1, p.17): allocate half the 10 mm heel to each leg.

This avoids counting the corner twice.

Ignore root radii consistently with that worked method.

Compute one angle, then double its resistance.

b1=200−10/2=195 mm,b2=100−10/2=95 mmb_1=200-10/2=195\,\mathrm{mm},\quad b_2=100-10/2=95\,\mathrm{mm}
ag1=195(10)=1950 mm2,a2=ag2=95(10)=950 mm2a_{g1}=195(10)=1950\,\mathrm{mm^2},\quad a_2=a_{g2}=95(10)=950\,\mathrm{mm^2}
an1=(195−2(30))(10)=1350 mm2,an2=950 mm2a_{n1}=(195-2(30))(10)=1350\,\mathrm{mm^2},\quad a_{n2}=950\,\mathrm{mm^2}
ae1=min⁡(1.1(1350),1950)=1485 mm2a_{e1}=\min(1.1(1350),1950)=1485\,\mathrm{mm^2}
ae2=min⁡(1.1(950),950)=950 mm2,Ae=1485+950=2435 mm2a_{e2}=\min(1.1(950),950)=950\,\mathrm{mm^2},\quad A_e=1485+950=2435\,\mathrm{mm^2}

Chapter 2 p.14 uses the 0.25 outstanding-leg reduction for double bolted angles on opposite sides of a gusset.

The single-angle 0.5 coefficient would be the wrong model.

At 10 mm thickness S355 has design strength 355 N/mm².

Pt,one=py(Ae−0.25a2)/1000=355(2435−0.25(950))/1000=780.1125 kNP_{t,one}=p_y(A_e-0.25a_2)/1000=355(2435-0.25(950))/1000=780.1125\,\mathrm{kN}
Pt,pair=2(780.1125)=1560.225 kN>1050 kNP_{t,pair}=2(780.1125)=1560.225\,\mathrm{kN}>1050\,\mathrm{kN}

The four requested strength checks pass, with angle bearing governing at 1,100 kN.

The drawn gauge is 80 mm whereas the course normal transverse spacing is 3d = 81 mm.

Record this 1 mm detailing discrepancy.

Do not silently redraw it or claim a complete compliant layout.

Source: LectureNotes/Ch2_Connection.pdf · p.4

Result and concise exam wording

Use the same mechanism: A bolt diameter is not a hole diameter. At fixed pitch, a larger hole leaves a shorter clear ligament. Increasing bolt diameter may also increase minimum edge-distance requirements.

Apply the reasoning to this section’s data and conditions

Concise exam wording

Ps=1377,Pbb=2160,Pbs,pair=1100,Pt,pair=1560.225[kN]P_s=1377,\quad P_{bb}=2160,\quad P_{bs,pair}=1100,\quad P_{t,pair}=1560.225\quad[\mathrm{kN}]

All exceed 1,050 kN; angle bearing governs.

Exclude gusset strength as instructed and note the 80/81 mm gauge discrepancy.

Misconceptions and checks

Use the same mechanism: Count cuts through each loaded bolt. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Apply the reasoning to this section’s data and conditions

  • Four bolts in double shear is not eight bolts carrying separate groups of load.
  • A transverse fracture cuts two holes, not one and not four.

Procedure for a new variant

Use the same mechanism: Count cuts through each loaded bolt. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Use the same mechanism: Follow contact pressure into the plate. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

Apply the reasoning to this section’s data and conditions

  1. Read the section view to count shear interfaces.
  2. Split load between identical angles, then check bolt and plate paths.
  3. Deduct holes on the actual transverse cut and use the double-angle coefficient.

Prediction with explained answer — invented variant

Use the same mechanism: Count cuts through each loaded bolt. For equal sharing and unchanged bolt area, two active planes provide twice one plane’s shear resistance.

Use the same mechanism: Follow contact pressure into the plate. At fixed geometry and strength, a thicker plate raises plate resistance. Moving a hole too near the end can still govern.

Use the same mechanism: One connected leg does not load both legs equally. Keeping the same gross area does not guarantee the same tension resistance when the connection arrangement changes.

Apply the reasoning to this section’s data and conditions

Invented variant: increase load by 5%.

Which mode decides adequacy?

Hint

Compare with the smallest resistance, not the largest.

Answer and reasoning

P=1.05(1050)=1102.5 kN>1100 kNP=1.05(1050)=1102.5\,\mathrm{kN}>1100\,\mathrm{kN}

Angle bearing now fails, despite bolt shear and angle tension still passing.