2014–2019 · Reference answers
2017-05-19 — beam answers
All independent beam subquestions, including the required sketches and restraint variants.
Independent teaching answer, not an official solution or marking scheme.
Printed marks are retained.
Read the source conditions beside each result.
Identify vertical supports and lateral restraints
Vertical bending can trigger sideways motion
A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.
Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.
Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.
LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.
Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.
Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.
Apply the reasoning to this section’s data and conditions
Units: 1 kN = 1,000 N; 1 m = 1,000 mm; 1 cm³ = 1,000 mm³; 1 cm⁴ = 10,000 mm⁴.
Demand is the load effect.
Resistance is the permitted capacity for the selected failure mode.
Compare matching units.
The triangular/roller end supports supply the vertical reactions.
Intermediate lateral restraints stop sideways motion of the compression flange; they do not supply extra vertical reactions.
Point-load distances below are read from the original dimension chain, measured from the left support.
All plotted loads are already factored.
Given: 356 × 171 × 51 UB, S355; total span 6 m; full-span UDL 1 kN/m; point loads 40 kN at x=1.5 m, 60 kN at x=3 m, 30 kN at x=4.5 m.
Lookup the exact 356 × 171 × 51 UB row.
Read dimensions first, properties second.
D = overall depth; t = web thickness; T = flange thickness; d = clear web depth.
The designation identifies a section-table row.
Read exact dimensions from that row.
S355 design strength depends on the actual flange thickness.
Local classification decides whether plastic bending resistance is allowed.
In pure bending the web limit is different from uniform compression.
Compare the flange class with the web class.
Use the more restrictive class.
Class 1 or 2 permits the capped plastic modulus.
Class 3 uses the elastic modulus.
Support reactions [3 marks]
Balance the isolated beam
Find the two vertical reactions before calculating internal shear or moment.
Prediction, then explanation. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.
Take moments about A. Reaction A has zero lever arm there. Then use vertical force balance to find reaction A.
P, RA and RB are forces in kN. L is support spacing and a is load position, both in m.
Scope. These expressions describe one point load on a simply supported beam. Add other loads through equilibrium; keep their actual positions.
Check and takeaway. Illustration: P = 60 kN, L = 6 m and a = 2 m give RB = 20 kN and RA = 40 kN.
Apply the reasoning to this section’s data and conditions
Take moments about the left support to eliminate RA, then sum vertical forces.
An applied counter-clockwise end couple contributes positively to the external moment balance and is subtracted when solving for RB.
Result and concise exam wording — key result lines
Take moments about the left support to eliminate RA, then sum vertical forces.
An applied counter-clockwise end couple contributes positively to the external moment balance and is subtracted when solving for RB.
Shear-force and bending-moment diagrams [4 marks]
A cut reveals the internal actions
Find where the beam moment is largest. A large load arrow alone does not locate that point.
Prediction, then explanation. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.
Balance the forces on the cut piece to get V. Balance their moments about the cut to get M. Evaluate each load region separately.
x and L use m; w uses kN/m; V uses kN; M uses kN·m. These lines apply before any point load.
Scope. A point load adds a shear jump. A concentrated couple adds a moment jump. Check load points, supports and overhang roots too.
Check and takeaway. A UDL gives a sloping shear line and a curved moment line. A flat moment diagram therefore cannot represent a loaded UDL region.
Apply the reasoning to this section’s data and conditions
Cut the beam at distance x.
Keep only loads to the left of the cut.
A point load drops the SFD by its magnitude.
The UDL gives slope −w.
The BMD is the integral of shear, so it is continuous through a point force and curved under a UDL.
Maximum moment can occur at a shear sign change or at a loaded/coupled boundary.
| x (m) | V just left (kN) | V just right (kN) | M (kN m) |
|---|---|---|---|
| 0 | 70.5 | 70.5 | 0 |
| 1.5 | 69 | 29 | 104.625 |
| 3 | 27.5 | -32.5 | 147 |
| 4.5 | -34 | -64 | 97.125 |
| 6 | -65.5 | -65.5 | 0 |
At the end supports the table gives the internal beam-side value.
The external SFD closes to zero after including the reaction.
At an internal zero-shear point, substitute x = (RA − preceding point loads)/w when that x lies within the interval.
Calculated SFD and BMD; point-load jumps, UDL curvature and labelled ordinates.
Result and concise exam wording — key result lines
At the end supports the table gives the internal beam-side value.
The external SFD closes to zero after including the reaction.
At an internal zero-shear point, substitute x = (RA − preceding point loads)/w when that x lies within the interval.
LTB: restraint positions 0, 6 m [13 marks]
Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.
Apply the reasoning to this section’s data and conditions
Check the segment x = 0 to 6 m.
Its length is 6 m.
The largest |M| occurs at x = 3 m.
Quarter stations: 1.5 m, 3 m, 4.5 m.
First locate the quarter, half and three-quarter points of this restraint segment.
Read the moment magnitude at each point.
Divide each magnitude by the largest moment magnitude anywhere in that segment.
The stations belong to the segment, not necessarily to the whole beam.
Apply the lower bound 0.44.
Use the stated normal-loading effective-length branch: LE equals the distance between effective lateral/torsional restraints.
A lateral restraint changes the stability model.
Add a vertical support only if the detail actually provides one.
Class 1/2 gives βW = 1.
Table 8.3, py = 355 N/mm² column; bracketing λLT rows 110 and 115.
Interpolate in this column only.
FAIL
Every listed segment must pass.
Do not compare the whole-beam maximum with a short segment’s capacity unless that maximum occurs in that segment.
Result and concise exam wording — key result lines
Every listed segment must pass.
Do not compare the whole-beam maximum with a short segment’s capacity unless that maximum occurs in that segment.
LTB: restraint positions 0, 1.5, 3, 4.5, 6 m [10 marks]
Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.
Apply the reasoning to this section’s data and conditions
Check the segment x = 0 to 1.5 m.
Its length is 1.5 m.
The largest |M| occurs at x = 1.5 m.
Quarter stations: 0.375 m, 0.75 m, 1.125 m.
First locate the quarter, half and three-quarter points of this restraint segment.
Read the moment magnitude at each point.
Divide each magnitude by the largest moment magnitude anywhere in that segment.
The stations belong to the segment, not necessarily to the whole beam.
Apply the lower bound 0.44.
Use the stated normal-loading effective-length branch: LE equals the distance between effective lateral/torsional restraints.
A lateral restraint changes the stability model.
Add a vertical support only if the detail actually provides one.
Class 1/2 gives βW = 1.
Table 8.3, py = 355 N/mm² column; bracketing λLT rows 30 and 35.
Interpolate in this column only.
PASS
Check the segment x = 1.5 to 3 m.
Its length is 1.5 m.
The largest |M| occurs at x = 3 m.
Quarter stations: 1.875 m, 2.25 m, 2.625 m.
First locate the quarter, half and three-quarter points of this restraint segment.
Read the moment magnitude at each point.
Divide each magnitude by the largest moment magnitude anywhere in that segment.
The stations belong to the segment, not necessarily to the whole beam.
Apply the lower bound 0.44.
Use the stated normal-loading effective-length branch: LE equals the distance between effective lateral/torsional restraints.
A lateral restraint changes the stability model.
Add a vertical support only if the detail actually provides one.
Class 1/2 gives βW = 1.
Table 8.3, py = 355 N/mm² column; bracketing λLT rows 30 and 35.
Interpolate in this column only.
PASS
Check the segment x = 3 to 4.5 m.
Its length is 1.5 m.
The largest |M| occurs at x = 3 m.
Quarter stations: 3.375 m, 3.75 m, 4.125 m.
First locate the quarter, half and three-quarter points of this restraint segment.
Read the moment magnitude at each point.
Divide each magnitude by the largest moment magnitude anywhere in that segment.
The stations belong to the segment, not necessarily to the whole beam.
Apply the lower bound 0.44.
Use the stated normal-loading effective-length branch: LE equals the distance between effective lateral/torsional restraints.
A lateral restraint changes the stability model.
Add a vertical support only if the detail actually provides one.
Class 1/2 gives βW = 1.
Table 8.3, py = 355 N/mm² column; bracketing λLT rows 30 and 35.
Interpolate in this column only.
PASS
Check the segment x = 4.5 to 6 m.
Its length is 1.5 m.
The largest |M| occurs at x = 4.5 m.
Quarter stations: 4.875 m, 5.25 m, 5.625 m.
First locate the quarter, half and three-quarter points of this restraint segment.
Read the moment magnitude at each point.
Divide each magnitude by the largest moment magnitude anywhere in that segment.
The stations belong to the segment, not necessarily to the whole beam.
Apply the lower bound 0.44.
Use the stated normal-loading effective-length branch: LE equals the distance between effective lateral/torsional restraints.
A lateral restraint changes the stability model.
Add a vertical support only if the detail actually provides one.
Class 1/2 gives βW = 1.
Table 8.3, py = 355 N/mm² column; bracketing λLT rows 30 and 35.
Interpolate in this column only.
PASS
Every listed segment must pass.
Do not compare the whole-beam maximum with a short segment’s capacity unless that maximum occurs in that segment.
Result and concise exam wording — key result lines
Every listed segment must pass.
Do not compare the whole-beam maximum with a short segment’s capacity unless that maximum occurs in that segment.
Reusable procedure and traps
Moment shape matters within one segment
Represent a nonuniform moment distribution in the applicable member-buckling equation.
Prediction, then explanation. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.
Evaluate moments from the true whole-beam analysis at the required positions. Apply the exact table’s weights, signs and lower bound.
mLT is an LTB factor. mx and my belong to the specified flexural checks. They are not interchangeable.
Scope. Some rules use magnitudes; others require signed ordinates. A factor does not reduce the actual moment used in a local section check.
Check and takeaway. Measure quarter points from the segment start, not automatically from the beam’s left support.
A safe beam can still sag too far
Check whether the beam displacement exceeds the permitted service limit.
Prediction, then explanation. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.
Load bends each beam segment. The curvature accumulates along the span. Material stiffness E and geometric stiffness I resist that deformation.
Use w in N/mm, L in mm, E in N/mm² and I in mm⁴. The resulting midspan deflection is in mm.
Scope. The formula assumes a prismatic, simply supported, linear-elastic beam with full-span UDL. Use the stated service load and deflection limit.
Check and takeaway. A higher yield grade does not automatically increase E. Passing a strength check therefore does not prove acceptable deflection.
Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.
Apply the reasoning to this section’s data and conditions
Separate ultimate resistance from imposed-load serviceability.
Keep kN/m and mm-based formulas consistent.
Establish the whole-beam reactions first.
For each restraint segment use its own length, quarter-point moments and maximum moment.
A high Mc does not prove LTB passes.
Check mLT M ≤ Mb as well as the applicable section resistance.
A smaller unrestrained length normally increases Mb.
However, its moment factor changes too.
Recalculate rather than scaling the old ratio.
Explained variant — invented example
Use the same mechanism: A safe beam can still sag too far. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.
Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.
A force couple carries moment
Separate the force couple used to carry moment from the force used to carry web shear.
Prediction, then explanation. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.
Moment is force multiplied by perpendicular separation. Divide the required moment by the specified separation to obtain each couple force.
M is moment in kN·mm; z is the specified force-line separation in mm; F is force in kN.
Scope. Use the lever arm defined by the source model. Do not silently replace it with overall section depth or another geometric distance.
Check and takeaway. Check flange welds for the couple forces and web welds for the stated shear model. Both force paths need a satisfactory detail.
Apply the reasoning to this section’s data and conditions
Invented variant: add a lateral brace at a quarter-span point without changing vertical supports or loads.
Which calculations change?
Hint
Separate the vertical-load model from the lateral-restraint model.
Explained answer
Reactions, SFD, BMD and vertical-load deflection remain unchanged in this ideal restraint model.
Create new LTB segments, then recalculate each LE, quarter-station moments, mLT, λLT, pb and utilisation.
The brace needs a stable load path and cannot be treated as a new vertical support.