FOUNDATIONS 1 / 4

Getting started: the question, symbols, units and tables

Four things to get right before any calculation: the words of the question, the symbols, the units and the tables.

Foundations

What the words in the question ask for

The questions and the Data File are in English. A few words decide which calculation you must do; miss one and every later step may use the wrong number. Circle the words in the table below before you start.

The most important thing is whether a load has already been multiplied by its load factor. A dead load and an imposed load are unfactored: multiply them by 1.4 and 1.6 before a strength check. An ultimate load, factored load or design load has already been multiplied: use it as it is.

The second thing is whether you must check or design. "Check" or "is adequate" means the sizes are given: work out the capacity and compare it with the demand. "Determine", "find the size" or "design" means working back from the demand to the size or number needed, then choosing a standard size not smaller than that.

Words in the questionMeaningWhat you do
dead load, permanent loadthe weight that is always thereunfactored; multiply by 1.4 for strength
imposed load, live loadthe load from useunfactored; multiply by 1.6 for strength, use as it is for deflection
ultimate load, factored load, design loada load already multiplied by its factoruse it as it is; do not multiply by 1.4 or 1.6 again
check, is adequatethe sizes are givenwork out the capacity, compare with the demand, state the result of every check
determine, find the size, designthe size or number is wantedwork back from the demand, then choose a standard size
Grade S355steel graderead the design strength from the Data File by grade and thickness
Grade 8.8, M20bolt grade, bolt diameter 20 mmread strengths and areas from the bolt tables
single shear, double shearone or two shear planeseach bolt is cut on one plane or on two
fillet weld, leg lengthtriangular weld and the length of its legthe throat is 0.7 times the leg
simply supportedfree to rotate at both endsvertical reactions only, no end moments
laterally restrained, unrestrainedheld sideways, or notan unrestrained length needs a lateral-torsional buckling check
effective lengthlength used for bucklingmultiply the actual length by a factor for the end conditions
UB, UCuniversal beam, universal columnfind its row in the section tables and copy the dimensions and properties
Foundations

Reading the symbols: small p is a strength, capital P is a capacity

Steel design formulas seem to have many symbols, but there are only a few families. Once you know which family a letter belongs to, you know its unit and which side of the comparison it goes on.

The most useful rule: a small pp with a subscript is a strength, the force one square millimetre of steel can take, in N/mm², read from the Data File. A capital PP with a subscript is a capacity, the force a whole bolt, plate or column can take, in kN, found as strength times area. A capital FF with a subscript is a demand, the force the loads really put on it, also in kN. Every check ends by comparing a demand with a capacity.

The subscript says which action: ss for shear, bb for bearing, tt for tension, cc for compression, ww for weld, yy for yield. So psp_s is the shear strength of a bolt, PsP_s the shear capacity VcV_c of one bolt, and FsF_s the shear force one bolt has to carry.

Greek letters are just more names. The table below gives the ones used in this course, how to say them and what they stand for.

Written asFamilyUnitExamples in this course
small pp with a subscriptstrength: force per mm², read from the Data FileN/mm²pyp_y, psp_s, pbbp_{bb}, pbsp_{bs}, pwp_w, pcp_c, pbp_b
capital PP with a subscriptcapacity: force the whole part can takekNPsP_s, PbbP_{bb}, PbsP_{bs}, PtP_t, PcP_c
capital FF with a subscriptdemand: force caused by the loadskNFsF_s, FcF_c
VV, VcV_cshear demand and shear capacity of a beamkNVV, VcV_c
MM with a subscriptmoment: MxM_x, MyM_y are demands; McM_c, MbM_b are capacitieskNmMxM_x, McM_c, MbM_b
AA with a subscriptareamm² or cm²AgA_g, AnA_n, AeA_e, AsA_s, AvA_v
SS, ZZsection modulus: turns a strength into a moment capacitycm³SxS_x, ZxZ_x
II, rrsecond moment of area, radius of gyrationcm⁴, cmIxI_x, ryr_y
LetterSayStands for
ε\varepsilonepsilonthe factor used in section classification, ε=275/py\varepsilon=\sqrt{275/p_y}
λ\lambdalambdaslenderness, λ=Le/r\lambda=L_e/r; the larger it is, the more easily the member buckles
λLT\lambda_{LT}lambda LTthe equivalent slenderness for lateral-torsional buckling
β\betabetathe ratio of the two end moments of a length, used to enter a table
Δ\Deltadeltadeflection, how many mm the beam sags
Σ\Sigmasigmaadd the terms together
η\etaetautilisation, demand divided by capacity
Foundations

Use units to identify what you are calculating (Units and Dimensions)

Do not start by memorising formulas. Every engineering quantity needs both a magnitude and a physical meaning: 20 kN is a force, 20 kN/m is force per metre of length, and 20 kN/m² is force per square metre. You cannot add these directly. Writing units at every step helps you catch mistakes before using a calculator.

1 kN=1000 N and 1 m=1000 mm. For area, square the length conversion: 1 cm²=100 mm². For volume or section modulus, the cubic conversion is 1 cm³=1000 mm³; for second moment of area II, 1 cm⁴=10000 mm⁴. Do not simply multiply by 10 whenever you see cm.

The course section tables commonly use cm², cm³ and cm⁴, whereas material strength is in N/mm². Strength times area gives N; strength times section modulus gives Nmm. Only at the end divide N by 1000 to obtain kN, and Nmm by 1000000 to obtain kNm.

Line loads ww have a convenient equivalence: 1 kN/m=1000 N/1000 mm=1 N/mm. The numerical values are equal, but this does not mean that unit conversions can generally be omitted.

1 kNm=106 Nmm1\ \mathrm{kNm}=10^6\ \mathrm{Nmm}
(N/mm2)(mm2)=N(\mathrm{N/mm^2})(\mathrm{mm^2})=\mathrm{N}
(N/mm2)(mm3)=Nmm(\mathrm{N/mm^2})(\mathrm{mm^3})=\mathrm{Nmm}
Symbol / UnitMeaning
kN\mathrm{kN}Kilonewton; force
kNm\mathrm{kNm}Moment
N/mm2\mathrm{N/mm^{2}}Stress or material strength
mm4\mathrm{mm^{4}}Second moment of area
Foundations

Reading a table and interpolating

Many values are not calculated but read from the tables of the Data File, such as the design strength pyp_y, the compressive strength pcp_c and the bending strength pbp_b. The routine is always the same: use the data of the question to choose the column, usually the value of pyp_y; then use the value you have calculated to choose the row, for example the slenderness λ\lambda. The cell where they meet is the answer.

Figure · A straight line between two rows
Table 8.3a, column py​ = 345λLT​pb​ (N/mm²)4031742.8308.645302Yellow and orange: the two rows in the tableRed dashes: the row you needThe same three values as a graphλLT​pb​ (N/mm²)(40, 317)(45, 302)308.642.8pb​ = 317 + (42.8 − 40) / (45 − 40) × (302 − 317) = 308.6 N/mm²
The column of Example 5: λLT=42.8\lambda_{LT}=42.8 lies between rows 40 and 45, 2.8/5 of the way. The table value moves the same fraction from 317 towards 302, giving 308.6 N/mm², which lies between 302 and 317.

A table lists round values only, such as λLT\lambda_{LT} equal to 40, 45, 50. Your value usually falls between two rows, such as 42.8. Then you interpolate: assume the change between the two rows is a straight line and take the value in proportion to the distance.

Three steps. First, find the rows above and below and copy four numbers: the two row headings and their table values. Second, work out what fraction of the way your value is from the upper row. Third, move the table value by the same fraction. When the table values fall as the rows go up, the result is smaller than the value of the upper row.

Then look at the result: it must lie between the two table values. If it does not, the sign is usually wrong.

y=y1+x−x1x2−x1(y2−y1)y=y_1+\frac{x-x_1}{x_2-x_1}(y_2-y_1)
Symbol / UnitMeaning
xxthe value you calculated, for example λLT\lambda_{LT}
x1x_1, x2x_2the headings of the rows above and below
y1y_1, y2y_2the table values of those two rows
yythe interpolated table value
↑ Top