FOUNDATIONS 2 / 4

How forces travel: actions, equilibrium and internal forces

First the four ways steel is loaded and the idea of demand against capacity, then how the force travels from the floor to the column.

Foundations

Four ways steel is loaded: tension, compression, shear, bending

However complicated the question, a piece of steel is loaded in only four ways. Recognise which one it is and you know how it deforms, how it fails and which set of formulas to use.

Figure · The four actions and how each one fails
Tensionpulled apart at the endsthe steel gets longerbreaks at thesmallest sectionCompressionpushed in at the endsthe steel gets shorteryields, orbows sideways (buckles)Sheartwo plates pull apartthe bolt is cut acrosscut through alongthe plane betweenBendingsqueezedstretchedtop gets shorterbottom gets longeryields, or the squeezedside buckles sideways
Dashed lines show the shape before or after loading; red arrows are the applied forces. Every check prevents one of these failures.

Tension pulls the steel longer. In tension, steel breaks where the cross-section is smallest; a bolt hole makes the section smaller, so the net area AnA_n with the holes taken out is used.

Compression squeezes the steel shorter. A short, stocky piece can be squeezed until it yields; a slender one bows sideways before it yields, which is called buckling. So a member in compression is checked for its length and the shape of its section, not only its area.

Shear makes two neighbouring parts slide past each other, like scissors cutting paper. A bolt pulled in opposite directions by two plates is cut where the plates meet; near a support the web of a beam also carries shear.

Bending is tension and compression together. When a simply supported beam sags, the top is squeezed shorter and the bottom is pulled longer. So the top flange behaves like a member in compression and may buckle sideways: this is lateral-torsional buckling.

ActionHow the steel deformsHow it failsWhere it appears in this course
Tensiongets longerbreaks at the smallest sectionangles and plates in tension, bolts in tension
Compressiongets shorteryields, or bows sidewayscolumns, the compression flange of a beam, the web over a support
Sheartwo parts slide past each othercut through along the sliding planebolts, welds, the web of a beam
Bendingone side shorter, the other longeryields, or the compression flange buckles sidewaysbeams, columns with eccentric reactions
Foundations

Material strength and member capacity (Stress and Resistance)

The same tensile force produces different stress levels in a thin and a thick steel rod. Average normal stress is force divided by the loaded area. With FF in N and AA in mm², stress is in N/mm².

Material yieldingMember instabilityService deformationMaterial strengthLength and restraintStiffness and loadDifferent failure modes → different checks
Supplementary schematic for understanding; not to scale.

Elasticity describes deformation that recovers on unloading. Yielding is the stage at which appreciable irreversible plastic deformation begins. Strain is the change in length divided by the original length: an extension of 1 mm over 1000 mm gives a dimensionless strain of 0.001. Elastic modulus EE relates stress to strain in the elastic range and describes stiffness; design yield strength pyp_y describes strength. EE and pyp_y are not interchangeable.

Material strength pyp_y is a design strength per unit area; member capacity is the force or moment that a whole section or member can resist. You cannot compare them directly: 169 kN cannot be compared directly with 355 N/mm². First calculate resistance using the appropriate area and design expression.

Demand is the action obtained from load analysis. Resistance is the capacity determined by the material, section and design conditions. Utilisation ratio is demand divided by resistance. A ratio no greater than 1 passes that individual check; all other necessary failure modes still require checking.

σ=F/A,η=DemandResistance\sigma=F/A,\qquad\eta=\frac{\text{Demand}}{\text{Resistance}}
Symbol / UnitMeaning
σ\sigmaAverage normal stress
pyp_yDesign yield strength used in this course
η\etaDimensionless utilisation ratio
Foundations

Why an object can remain stationary (Forces and Equilibrium)

Think of a beam as a ruler resting on two supports. Downward loads tend to move it, while the supports push upwards. If the beam remains stationary without rotating, the sums of horizontal forces, vertical forces and moments must all be zero. This is static equilibrium.

PRA​RB​Span between supports, L
Supplementary schematic for understanding; not to scale.

A support reaction RR is not extra weight imposed by the question. It is the force exerted by a support to prevent the member from moving. Assume a direction when drawing it; a negative calculated value means that the actual direction is opposite to your assumption.

Correct reactions RR establish overall force and moment equilibrium; they do not yet prove that the beam is strong enough. You must still check the internal shear force, bending moment MM, deformation and stability. This is why the lecturer calculates internal actions before selecting a section.

∑Fx=0,∑Fy=0,∑M=0\sum F_x=0,\qquad\sum F_y=0,\qquad\sum M=0
Symbol / UnitMeaning
FFForce; usually kN
RRSupport reaction; usually kN
Σ\SigmaSum all terms in the same direction or about the same moment centre
Foundations

Why the position of a force matters (Moment and Eccentricity)

The same push produces different turning effects at a door handle and near the hinge. Moment measures this turning effect. Its magnitude is force times the perpendicular distance from the moment centre to the line of action of the force. This distance is the lever arm, which need not be the longest diagonal shown in the drawing.

Eccentricity ePDirect force P + eccentric moment Pe
Supplementary schematic for understanding; not to scale.

A connection is eccentric when the load does not pass through the centre of its bolt or weld group. In addition to direct shear, the connection must resist the turning effect PePe. Dividing the whole load equally between the bolts accounts only for direct shear, not the eccentric moment.

Mark the centre, the load's line of action and the perpendicular distance ee on the drawing before calculating. PP in kN times ee in mm gives kNmm. To obtain kNm, first divide ee by 1000, or divide the result by 1000.

M=PeM=Pe
Symbol / UnitMeaning
PPForce
eePerpendicular eccentricity
MMMoment about the selected centre
Foundations

Turn the physical structure into a calculation model (Free-body Diagram)

A free-body diagram (FBD) isolates the member under investigation and replaces the actions of surrounding members with forces and moments. Show loads, reactions RR, support positions, spans LL and necessary dimensions, rather than copying every detail of the building plan.

UDL w (kN/m)RA​RB​Span between supports, L
Supplementary schematic for understanding; not to scale.

The course commonly uses a simply supported model: the ends can rotate and no additional end moments are applied. For ordinary vertical-load problems, the focus is on the two vertical reactions RR. A fixed end can transmit moment, so the same simply supported formulas cannot replace a fixed-end analysis.

When isolating B1 from the floor plan, retain its actual loads and span LL. When isolating B3, the support reaction RR from B2 at their intersection becomes a point load on B3. Members on the same floor do not necessarily have the same free-body diagram.

Symbol / UnitMeaning
LLAnalysis span between supports
PPPoint load
wwUniformly distributed load
Foundations

How loads travel from the slab to the ground (Load Path)

A load path describes the members through which forces travel. For example, a slab loads secondary beams; their support reactions RR load primary beams; the primary beams transfer forces to columns and foundations. Each connection must transfer the force from one member to the next.

SlabSecondary beamPrimary beamColumnArea load q → Line load w → Reaction R → Axial force FAt each conversion, identify the member receiving the force
Supplementary schematic for understanding; not to scale.

Tributary width btribb_{trib} is the slab width allocated to a beam. In the course's one-way slab example, an edge beam receives half a bay on one side; an internal beam receives half a bay on each side. Equal spans LL therefore do not necessarily mean equal line loads ww. This allocation depends on the stated slab spanning direction and support assumptions; it is not a universal rule for all floors.

Identify the conversion stage first: material unit weight times thickness gives area load qq; area load times tributary width btribb_{trib} gives line load ww; beam equilibrium converts line loads into support reactions RR. Each conversion changes the physical quantity represented by the number.

q=γt,w=qbtribq=\gamma t,\qquad w=qb_{trib}
Symbol / UnitMeaning
γ\gammaMaterial unit weight, kN/m³
ttSlab thickness, m
qqArea load, kN/m²
btribb_{trib}Tributary width, m
wwLine load, kN/m
Foundations

Internal shear force and bending moment in a beam (Shear Force and Bending Moment)

A beam carries downward external loads and upward reactions RR. Internal actions must maintain continuity. Imagine cutting it at a distance xx from the left support and retaining the left-hand portion. Add shear force VV and bending moment MM at the cut so that this portion also remains in equilibrium.

UDL w (kN/m)RA​RB​Span between supports, LIsolate a segment: V balances vertical forces; M balances moments
Supplementary schematic for understanding; not to scale.

For a simply supported beam with a full-span UDL ww, symmetry gives RA=RB=wL/2R_A=R_B=wL/2. At a section xx from the left end, the load on the left portion has a resultant wxwx acting at its midpoint x/2x/2. Thus V=RA−wxV=R_A-wx and M=RAx−wx2/2M=R_Ax-wx^{2}/2. These expressions describe how the internal actions vary along the beam.

At midspan, x=L/2x=L/2, the UDL beam has zero shear and its maximum positive moment. Substitution gives wL2/8wL^{2}/8. The support shear magnitude is wL/2wL/2. These results apply only to the corresponding supports and loading; an overhanging beam or an off-centre point load requires a fresh analysis.

RA=RB=wL/2R_A=R_B=wL/2
V(x)=RA−wx,M(x)=RAx−wx2/2V(x)=R_A-wx,\qquad M(x)=R_Ax-wx^2/2
V(x)=RA−wxM(x)=RAx−wx2/2\begin{aligned}V(x)&=R_A-wx\\M(x)&=R_Ax-wx^2/2\end{aligned}
Mmax=wL2/8M_{max}=wL^2/8
Symbol / UnitMeaning
xxPosition measured from the left support
VVSection shear force, kN
MMSection bending moment, kNm
↑ Top