Steelwork · Exam learning

2022–2024 · Exam-focused route

Recent-paper transfer practice and timed revision

These short questions are invented transfer checks, not predicted exam questions or official marking guidance. Try each without its answer, say which model applies, then calculate. Every new worked page also has a separate changed-input self-check.

1. Floor transfer

Two identical 8 m beams each carry an already-factored UDL of 40 kN/m and meet at the midpoint of a 6 m supporting beam. Ignore its self-weight. Find its point load, support shear and maximum moment.

Reveal worked answer
R1=40(8)/2=160 kN;P=2R1=320 kN;V=160 kN;M=320(6)/4=480 kN mR_1=40(8)/2=160\,\mathrm{kN};\quad P=2R_1=320\,\mathrm{kN};\quad V=160\,\mathrm{kN};\quad M=320(6)/4=480\,\mathrm{kN\,m}

2. Deflection scaling

A UDL beam has 12 mm imposed-load deflection. Increase span by 10%, with the same section and line load. Estimate the new deflection before recalculating the limit.

Reveal worked answer
δnew=12(1.1)4=17.5692 mm\delta_{new}=12(1.1)^4=17.5692\,\mathrm{mm}

The span/360 limit rises only by 10%; utilization rises by 1.1³ = 1.331. A longer span can lose its margin rapidly.

3. Pick the bolt plane count

Four M27 Grade 8.8 bolts connect angle–gusset–angle. Use As=459 mm² and ps=375 N/mm². What changes if one outer angle is removed and load remains the same?

Reveal worked answer
Pdouble=4(2)(459)(375)/1000=1377 kN;Psingle=688.5 kNP_{double}=4(2)(459)(375)/1000=1377\,\mathrm{kN};\quad P_{single}=688.5\,\mathrm{kN}

The shear capacity halves. Angle tension, eccentricity and bearing also require a new model; do not halve only one result and declare the new joint adequate.

4. Choose the weld mechanism

A load acts in the plane of a closed rectangular weld group, offset from its centroid. Another bracket assigns shear to web welds and bending to flange welds. Can their formulas be interchanged?

Reveal worked answer

No. The first needs direct shear plus in-plane torsion using the polar line moment. The second uses web shear plus an out-of-plane flange force couple with a specified lever arm. Classify the geometry before selecting an equation.

5. Reversed moments

Applied top/bottom moments are −80 and +40 kN·m, clockwise positive. Under the course opposite-end-face convention find the internal ratio and positive-ratio flexural moment factor.

Reveal worked answer
β=−(+40)/(−80)=0.5;m=0.6+0.4(0.5)=0.8\beta=-(+40)/(-80)=0.5;\quad m=0.6+0.4(0.5)=0.8

6. Read restraint symbols

A free overhang tip is marked with a lateral-restraint cross. May you put a vertical reaction there or use the simple-span LTB moment factor?

Reveal worked answer

Neither follows from the cross. It specifies lateral restraint only. Solve vertical statics from actual supports; apply the cantilever moment-factor and effective-length rules with explicit torsional and loading conditions.

Two-hour recent-paper rehearsal

Use the supplied 2024 paper for a closed-answer first attempt, then the 2023 FT/PTD paper as a transfer attempt. If you already studied both, use the existing invented two-hour mock and full solutions. Keep the source data tables available as allowed by the printed paper format.

Use the supplied exam format

Two hours. Section A is compulsory: 40 marks. Choose any TWO of the three Section B questions, 30 marks each. Answer 100 marks out of 130 offered. These are printed allocations, not an invented marking scheme.

Suggested timing: 5 minutes to read and choose, 42 minutes for Section A, 32 minutes per chosen Section B question, 9 minutes to check. Choose using the entire question, including the smaller subparts and missing assumptions.

Record a decision log after the attempt: first wrong step, its source, the corrected method, and a changed-input re-test. Award yourself no “official method marks”: no marking scheme was supplied. A useful readiness criterion is completing Section A plus two Section B families within two hours, with units and source assumptions stated and no help from revealed solutions.

Last-pass decision checklist

  • Already factored? Do not factor twice. Mass or weight? Convert only once.
  • Which support resists vertical force? Which symbol only restrains lateral movement?
  • How many incoming beam reactions? How many shear planes? How many holes on this net section?
  • Does the table row use flange thickness, web thickness, bolt diameter, or electrode class?
  • Are moments first-order or amplified? Is the denominator elastic or plastic?
  • Is a missing restraint being disguised as a numerical assumption? State it.