Note: marks are as printed in the paper; the working is a teaching guide, not an official marking scheme.
Choose the column model first
The 2022 and 2023 papers use the same 305 × 305 × 158 UC but give the moments in different ways. 2022 (this page): the end moments are given directly, with signs — use the continuous non-sway column method. 2023: beam reactions act off-centre at a joint — use the course’s simple-construction method, share the joint moment by stiffness, and use the moment factors the paper gives.
Simple explanation — open only if needed
A short steel block may survive squeezing while a long ruler with the same cross-section bends sideways. The section check asks whether the steel at one slice is strong enough. The member checks also ask whether the whole column can buckle. Passing one does not replace the others.
These are lookups from the exact UC row. The flange thickness selects the S355 design strength 345 N/mm². A is area, r radius of gyration, Z elastic modulus, S plastic modulus, T flange thickness and t web thickness. u and x are the LTB section parameters, not geometric coordinates.
Given end moments and amplification
Given effective height 4.5 m and axial force 3,000 kN. Clockwise applied end moments are positive: x-axis top −90, bottom +70 kN·m; y-axis top −60, bottom −50 kN·m. Amplification factors are 1.10 and 1.15; the stated LTB moment is 99 kN·m. Keep first-order moments separate from amplified ones.
The axial force compresses the web as well as bending it. To avoid a pure-bending classification shortcut, use the most restrictive 40ε web bound of the Class 1 general-stress expression: its stress-ratio parameter is capped at one. The web thickness is below 16 mm, so its S355 strength is 355 N/mm². The flange uses 345 N/mm².
ϵf=275/345=0.892805,6.22<9ϵf=8.035248
ϵw=275/355=0.880141,15.6<40ϵw=35.205633
Under axial force plus bending, both the flange and the web meet the Class 1 limits.
The cross-section check combines axial compression and two bending components at one section. Use amplified moments, gross compression resistance and the Class 1 capped plastic bending resistances. Every ratio must be dimensionless.
For the rolled UC with flange thickness below 40 mm, choose strut curve b about x and curve c about y. Effective length divided by the corresponding radius gives slenderness. Use the 345 N/mm² column of each curve’s compression-strength table.
Moment factors use the internal bending diagram, not the raw clockwise arrows at opposite end faces. Hold the top sign and reverse the bottom-face applied moment when forming the internal end ratio. For x this gives same-sign internal end moments; for y, opposite-sign. Then select the positive or negative ratio branch of Table 8.9.
βx=−90−(+70)=+0.777778,βy=−60−(−50)=−0.833333
mx=0.6+0.4βx=0.911111,my=0.6+0.2βy=0.433333
mLT=max(0.44,0.6+0.4βx)=0.911111
Use the continuous-column LTB branch with the stated effective height, and the section u/x parameters. Do not substitute the simple-construction half-height rule.
Choose Data File p.5, Table 8.3, 345 N/mm² column. Interpolate between the two surrounding slenderness rows in the same design-strength column; do not mix columns.
For the member interaction equations, the course uses ELASTIC section bending resistances. These are different from the capped plastic resistances used in the section check. The first member equation uses the smaller compression resistance and amplified moments.
The second member equation combines minor-axis compression buckling with major-axis LTB. It uses MLT as stated above and the first-order minor-axis moment (the barred moment in the course summary). Do not insert the amplified minor-axis moment again.