2022–2024 · Exam-focused route
2022 BQ3 — two point loads and LTB segments
Solve the entire vertical beam, then check BC and CD as separate laterally restrained segments.
Marks are as printed in the paper; the working is a teaching guide, not an official marking scheme.
Separate vertical supports from lateral restraints
Vertical bending can trigger sideways motion
A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.
Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.
Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.
LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.
Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.
Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.
Apply the reasoning to this section’s data and conditions
Given: A and D are the simple vertical supports, 8.5 m apart.
B is 3 m from A, C another 2 m to the right, and D another 3.5 m.
Downward factored point loads are 200 kN at B and 320 kN at C.
The full-length factored UDL is 1.6 kN/m including self-weight.
Lateral restraints occur at A, B, C and D; they split the buckling lengths but do not create extra vertical reactions.
Section 533 × 210 × 109 UB is S355, Class 1.
Physical interpretation and limits
A hand stopping a ruler moving sideways is not the same as a prop holding its weight up.
Solve vertical reactions using the actual props first.
Use the side restraints only when deciding which length can twist sideways.
BQ3(a) — support reactions [3 marks]
Balance the isolated beam
Find the two vertical reactions before calculating internal shear or moment.
Prediction, then explanation. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.
Take moments about A. Reaction A has zero lever arm there. Then use vertical force balance to find reaction A.
P, RA and RB are forces in kN. L is support spacing and a is load position, both in m.
Scope. These expressions describe one point load on a simply supported beam. Add other loads through equilibrium; keep their actual positions.
Check and takeaway. Illustration: P = 60 kN, L = 6 m and a = 2 m give RB = 20 kN and RA = 40 kN.
Apply the reasoning to this section’s data and conditions
Take moments about A to eliminate its reaction.
The UDL resultant is its intensity times the full span and acts at the span centre.
Then use vertical force equilibrium.
Both reactions are upward; together they equal 533.6 kN.
Already factored loads receive no second load factor.
BQ3(b) — annotated shear and moment diagrams [4 marks]
A cut reveals the internal actions
Find where the beam moment is largest. A large load arrow alone does not locate that point.
Prediction, then explanation. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.
Balance the forces on the cut piece to get V. Balance their moments about the cut to get M. Evaluate each load region separately.
x and L use m; w uses kN/m; V uses kN; M uses kN·m. These lines apply before any point load.
Scope. A point load adds a shear jump. A concentrated couple adds a moment jump. Check load points, supports and overhang roots too.
Check and takeaway. A UDL gives a sloping shear line and a curved moment line. A flat moment diagram therefore cannot represent a loaded UDL region.
Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.
Apply the reasoning to this section’s data and conditions
Use x in metres measured from A, positive sagging moment, and shear equal to the sum of vertical forces to the left.
At a downward point load, shear jumps down but moment stays continuous.
Between loads, the UDL makes shear linear and moment quadratic.
H is zero before its load and one after.
The angle-bracket term means use zero before the load and the positive distance after it.
This is only a compact way to write the ordinary left-of-section force and moment sums.
| Position | Shear just left → right (kN) | Moment (kN·m) |
|---|---|---|
| A | 0 → 267.976471 | 0 |
| B | 263.176471 → 63.176471 | 796.729412 |
| C | 59.976471 → -260.023529 | 919.882353 |
| D | -265.623529 → 0 | 0 |
Shear is positive up to C and negative after C, so C is the maximum sagging moment.
The computed end moment at D is zero, checking the reaction arithmetic.
Calculated teaching diagrams: all jumps, supports and moment ordinates are labelled; curves include the UDL.
Section and restraint data for LTB
Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.
Apply the reasoning to this section’s data and conditions
BQ3(c) — segment BC [13 marks]
Moment shape matters within one segment
Represent a nonuniform moment distribution in the applicable member-buckling equation.
Prediction, then explanation. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.
Evaluate moments from the true whole-beam analysis at the required positions. Apply the exact table’s weights, signs and lower bound.
mLT is an LTB factor. mx and my belong to the specified flexural checks. They are not interchangeable.
Scope. Some rules use magnitudes; others require signed ordinates. A factor does not reduce the actual moment used in a local section check.
Check and takeaway. Measure quarter points from the segment start, not automatically from the beam’s left support.
Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.
Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.
Apply the reasoning to this section’s data and conditions
For BC, use the original global x coordinate in the moment formula.
Its maximum absolute moment is at C.
The lateral restraint spacing is 2 m.
Use the moments at one-quarter, one-half and three-quarters of THIS restrained segment.
They are not necessarily at load points.
Evaluate the actual quadratic bending diagram including the UDL.
Use absolute magnitudes in the quarter-point expression and compare with the maximum absolute moment in the segment.
| Quarter point coordinate | Moment (kN·m) |
|---|---|
Use millimetres in slenderness.
The section table supplies the minor-axis radius of gyration, buckling parameter and torsional index.
The given Class 1 section has a plastic-section factor of one.
These quantities change when the section changes.
Choose Data File p.5, Table 8.3, 345 N/mm² column.
Interpolate between the two surrounding slenderness rows in the same design-strength column.
Do not mix columns.
Buckling strength times plastic modulus gives moment resistance.
Convert the tabulated cubic centimetres to cubic millimetres, then newton-millimetres to kilonewton-metres.
The stated effective-length model passes this LTB check.
BQ3(d) — segment CD [10 marks]
Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.
Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.
Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.
Apply the reasoning to this section’s data and conditions
For CD, use the original global x coordinate in the moment formula.
Its maximum absolute moment is at C.
The lateral restraint spacing is 3.5 m.
Use the moments at one-quarter, one-half and three-quarters of THIS restrained segment.
They are not necessarily at load points.
Evaluate the actual quadratic bending diagram including the UDL.
Use absolute magnitudes in the quarter-point expression and compare with the maximum absolute moment in the segment.
| Quarter point coordinate | Moment (kN·m) |
|---|---|
Use millimetres in slenderness.
The section table supplies the minor-axis radius of gyration, buckling parameter and torsional index.
The given Class 1 section has a plastic-section factor of one.
These quantities change when the section changes.
Choose Data File p.5, Table 8.3, 345 N/mm² column.
Interpolate between the two surrounding slenderness rows in the same design-strength column.
Do not mix columns.
Buckling strength times plastic modulus gives moment resistance.
Convert the tabulated cubic centimetres to cubic millimetres, then newton-millimetres to kilonewton-metres.
The stated effective-length model passes this LTB check.
Result and concise exam wording
Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.
Apply the reasoning to this section’s data and conditions
Concise exam wording
Both segments pass the stated normal-loading/effective-length branch; provide SFD/BMD and restraint qualification.
Misconceptions and checks
Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.
Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.
Apply the reasoning to this section’s data and conditions
- B and C lateral restraints are not extra vertical supports.
- Quarter points belong to each segment, not the entire 8.5 m beam.
- Do not replace the curved CD moment diagram with an exact straight triangle.
Procedure for a new variant
Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.
Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.
A table value has conditions
Find a design property without mixing a row, column or standard from a different case.
Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.
Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.
Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.
Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.
Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.
Apply the reasoning to this section’s data and conditions
- Find vertical reactions and the full SFD/BMD.
- Identify actual restraints and effective lengths.
- Evaluate segment quarter moments, mLT, slenderness and table strength.
Prediction with explained answer — invented variant
Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.
Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.
Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.
Apply the reasoning to this section’s data and conditions
Invented variant: add a lateral restraint halfway through CD without changing vertical supports.
Do reactions change?
Hint
Separate vertical statics from lateral buckling.
Answer and reasoning
No. Vertical reactions and the existing bending diagram stay the same.
Split CD into two LTB segments, choose the new effective lengths and recompute each segment’s quarter-point factor and resistance.