Steelwork · Exam learning

2022–2024 · Exam-focused route

2022 BQ3 — two point loads and LTB segments

All answers shown

Solve the entire vertical beam, then check BC and CD as separate laterally restrained segments.

Original source: 21ENGTY031.pdf · physical page 6

Marks are as printed in the paper; the working is a teaching guide, not an official marking scheme.

Separate vertical supports from lateral restraints

Vertical bending can trigger sideways motion

A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.

The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.
The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.

Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.

λ=LE/ry,Mb=pbSx  (Class 1/2),mLTMmax≤Mb\lambda=L_E/r_y,\qquad M_b=p_bS_x\;\text{(Class 1/2)},\qquad m_{LT}M_{max}\le M_b

LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.

Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.

Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.

Apply the reasoning to this section’s data and conditions

Given: A and D are the simple vertical supports, 8.5 m apart.

B is 3 m from A, C another 2 m to the right, and D another 3.5 m.

Downward factored point loads are 200 kN at B and 320 kN at C.

The full-length factored UDL is 1.6 kN/m including self-weight.

Lateral restraints occur at A, B, C and D; they split the buckling lengths but do not create extra vertical reactions.

Section 533 × 210 × 109 UB is S355, Class 1.

Physical interpretation and limits

A hand stopping a ruler moving sideways is not the same as a prop holding its weight up.

Solve vertical reactions using the actual props first.

Use the side restraints only when deciding which length can twist sideways.

BQ3(a) — support reactions [3 marks]

Balance the isolated beam

Find the two vertical reactions before calculating internal shear or moment.

A / RₐB / RᵦPaL
A and B are vertical supports. The downward load acts at distance a from A. Its distance from B is L − a.

Prediction, then explanation. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Take moments about A. Reaction A has zero lever arm there. Then use vertical force balance to find reaction A.

RBL=Pa,RA+RB=PR_B L=Pa,\qquad R_A+R_B=P

P, RA and RB are forces in kN. L is support spacing and a is load position, both in m.

Scope. These expressions describe one point load on a simply supported beam. Add other loads through equilibrium; keep their actual positions.

Check and takeaway. Illustration: P = 60 kN, L = 6 m and a = 2 m give RB = 20 kN and RA = 40 kN.

Apply the reasoning to this section’s data and conditions

Take moments about A to eliminate its reaction.

The UDL resultant is its intensity times the full span and acts at the span centre.

Then use vertical force equilibrium.

W=1.6(8.5)=13.6 kN,xW=8.5/2=4.25 mW=1.6(8.5)=13.6\,\mathrm{kN},\quad x_W=8.5/2=4.25\,\mathrm{m}
RD=200(3)+320(5)+13.6(4.25)8.5=265.623529 kNR_D=\frac{200(3)+320(5)+13.6(4.25)}{8.5}=265.623529\,\mathrm{kN}
RA=200+320+13.6−RD=267.976471 kNR_A=200+320+13.6-R_D=267.976471\,\mathrm{kN}

Both reactions are upward; together they equal 533.6 kN.

Already factored loads receive no second load factor.

BQ3(b) — annotated shear and moment diagrams [4 marks]

A cut reveals the internal actions

Find where the beam moment is largest. A large load arrow alone does not locate that point.

The dashed imaginary cut separates two beam pieces. The opposing arrows represent the shear action between those pieces.
The dashed imaginary cut separates two beam pieces. The opposing arrows represent the shear action between those pieces.

Prediction, then explanation. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Balance the forces on the cut piece to get V. Balance their moments about the cut to get M. Evaluate each load region separately.

V(x)=RA−wx,M(x)=RAx−wx22V(x)=R_A-wx,\qquad M(x)=R_Ax-\frac{wx^2}{2}

x and L use m; w uses kN/m; V uses kN; M uses kN·m. These lines apply before any point load.

Scope. A point load adds a shear jump. A concentrated couple adds a moment jump. Check load points, supports and overhang roots too.

Check and takeaway. A UDL gives a sloping shear line and a curved moment line. A flat moment diagram therefore cannot represent a loaded UDL region.

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

Apply the reasoning to this section’s data and conditions

Use x in metres measured from A, positive sagging moment, and shear equal to the sum of vertical forces to the left.

At a downward point load, shear jumps down but moment stays continuous.

Between loads, the UDL makes shear linear and moment quadratic.

V(x)=267.976471−1.6x−200H(x−3)−320H(x−5)[kN]V(x)=267.976471-1.6x-200H(x-3)-320H(x-5)\quad[\mathrm{kN}]
M(x)=267.976471x−0.8x2−200⟨x−3⟩−320⟨x−5⟩[kN m]M(x)=267.976471x-0.8x^2-200\langle x-3\rangle-320\langle x-5\rangle\quad[\mathrm{kN\,m}]

H is zero before its load and one after.

The angle-bracket term means use zero before the load and the positive distance after it.

This is only a compact way to write the ordinary left-of-section force and moment sums.

PositionShear just left → right (kN)Moment (kN·m)
A0 → 267.9764710
B263.176471 → 63.176471796.729412
C59.976471 → -260.023529919.882353
D-265.623529 → 00
MB=267.976471(3)−0.8(32)=796.729412 kN mM_B=267.976471(3)-0.8(3^2)=796.729412\,\mathrm{kN\,m}
MC=267.976471(5)−0.8(52)−200(5−3)=919.882353 kN mM_C=267.976471(5)-0.8(5^2)-200(5-3)=919.882353\,\mathrm{kN\,m}

Shear is positive up to C and negative after C, so C is the maximum sagging moment.

The computed end moment at D is zero, checking the reaction arithmetic.

Calculated teaching diagrams: all jumps, supports and moment ordinates are labelled; curves include the UDL.

Calculated teaching diagrams: all jumps, supports and moment ordinates are labelled; curves include the UDL.

Full-size image

Section and restraint data for LTB

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.1, p.9, p.10
T=18.8 mm⇒py=345 N/mm2,ry=4.60 cm=46 mmT=18.8\,\mathrm{mm}\Rightarrow p_y=345\,\mathrm{N/mm^2},\quad r_y=4.60\,\mathrm{cm}=46\,\mathrm{mm}
u=0.875,x=30.9,Sx=2828 cm3,βW=1u=0.875,\quad x=30.9,\quad S_x=2828\,\mathrm{cm^3},\quad\beta_W=1

BQ3(c) — segment BC [13 marks]

Moment shape matters within one segment

Represent a nonuniform moment distribution in the applicable member-buckling equation.

The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.
The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.

Prediction, then explanation. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Evaluate moments from the true whole-beam analysis at the required positions. Apply the exact table’s weights, signs and lower bound.

mLT is an LTB factor. mx and my belong to the specified flexural checks. They are not interchangeable.

Scope. Some rules use magnitudes; others require signed ordinates. A factor does not reduce the actual moment used in a local section check.

Check and takeaway. Measure quarter points from the segment start, not automatically from the beam’s left support.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Apply the reasoning to this section’s data and conditions

For BC, use the original global x coordinate in the moment formula.

Its maximum absolute moment is at C.

The lateral restraint spacing is 2 m.

M(3.5)=267.976471(3.5)−0.8(3.52)−200(3.5−3)=828.117647 kN mM(3.5)=267.976471(3.5)-0.8(3.5^2)-200(3.5-3)=828.117647\,\mathrm{kN\,m}
M(4)=267.976471(4)−0.8(42)−200(4−3)=859.105882 kN mM(4)=267.976471(4)-0.8(4^2)-200(4-3)=859.105882\,\mathrm{kN\,m}
M(4.5)=267.976471(4.5)−0.8(4.52)−200(4.5−3)=889.694118 kN mM(4.5)=267.976471(4.5)-0.8(4.5^2)-200(4.5-3)=889.694118\,\mathrm{kN\,m}
Source: LectureNotes/Ch3_Beam.pdf · p.16

Use the moments at one-quarter, one-half and three-quarters of THIS restrained segment.

They are not necessarily at load points.

Evaluate the actual quadratic bending diagram including the UDL.

Use absolute magnitudes in the quarter-point expression and compare with the maximum absolute moment in the segment.

Quarter point coordinateMoment (kN·m)
x=3.5 mx=3.5\,\mathrm{m}M=828.117647 kN mM=828.117647\,\mathrm{kN\,m}
x=4 mx=4\,\mathrm{m}M=859.105882 kN mM=859.105882\,\mathrm{kN\,m}
x=4.5 mx=4.5\,\mathrm{m}M=889.694118 kN mM=889.694118\,\mathrm{kN\,m}
mLT=max⁡(0.44, 0.2+0.15∣M2∣+0.5∣M3∣+0.15∣M4∣∣Mmax∣)m_{LT}=\max\left(0.44,\ 0.2+\frac{0.15|M_2|+0.5|M_3|+0.15|M_4|}{|M_{max}|}\right)
mLT=max⁡(0.44, 0.2+0.15∣828.117647∣+0.5∣859.105882∣+0.15∣889.694118∣919.882353)m_{LT}=\max\left(0.44,\ 0.2+\frac{0.15|828.117647|+0.5|859.105882|+0.15|889.694118|}{919.882353}\right)
mLT=0.947079m_{LT}=0.947079

Use millimetres in slenderness.

The section table supplies the minor-axis radius of gyration, buckling parameter and torsional index.

The given Class 1 section has a plastic-section factor of one.

These quantities change when the section changes.

LE=2000  mm,ry=46  mm,u=0.875,x=30.9,βW=1L_E=2000\;\mathrm{mm},\quad r_y=46\;\mathrm{mm},\quad u=0.875,\quad x=30.9,\quad\beta_W=1
λ=LEry=200046=43.478261\lambda=\frac{L_E}{r_y}=\frac{2000}{46}=43.478261
v=[1+0.05(λx)2]−1/4=[1+0.05(43.47826130.9)2]−1/4=0.976678v=\left[1+0.05\left(\frac{\lambda}{x}\right)^2\right]^{-1/4}=\left[1+0.05\left(\frac{43.478261}{30.9}\right)^2\right]^{-1/4}=0.976678
λLT=uvλβW=0.875×0.976678×43.478261=37.15623\lambda_{LT}=uv\lambda\sqrt{\beta_W}=0.875\times0.976678\times43.478261=37.15623
Source: LectureNotes/CON4334-Data File-20260730.pdf · p.5

Choose Data File p.5, Table 8.3, 345 N/mm² column.

Interpolate between the two surrounding slenderness rows in the same design-strength column.

Do not mix columns.

pb=332+37.15623−3540−35(317−332)=325.531309  N/mm2p_b=332+\frac{37.15623-35}{40-35}(317-332)=325.531309\;\mathrm{N/mm^2}

Buckling strength times plastic modulus gives moment resistance.

Convert the tabulated cubic centimetres to cubic millimetres, then newton-millimetres to kilonewton-metres.

Mb=pbSx×103106=325.531309×28281000=920.602542  kN mM_b=\frac{p_b S_x\times10^3}{10^6}=\frac{325.531309\times2828}{1000}=920.602542\;\mathrm{kN\,m}
mLTMmax=0.947079×919.882353=871.201176  kN mm_{LT}M_{max}=0.947079\times919.882353=871.201176\;\mathrm{kN\,m}
mLTMmaxMb=871.201176920.602542=0.946338≤1\frac{m_{LT}M_{max}}{M_b}=\frac{871.201176}{920.602542}=0.946338\le1

The stated effective-length model passes this LTB check.

BQ3(d) — segment CD [10 marks]

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Apply the reasoning to this section’s data and conditions

For CD, use the original global x coordinate in the moment formula.

Its maximum absolute moment is at C.

The lateral restraint spacing is 3.5 m.

M(5.875)=267.976471(5.875)−0.8(5.8752)−200(5.875−3)−320(5.875−5)=691.749265 kN mM(5.875)=267.976471(5.875)-0.8(5.875^2)-200(5.875-3)-320(5.875-5)=691.749265\,\mathrm{kN\,m}
M(6.75)=267.976471(6.75)−0.8(6.752)−200(6.75−3)−320(6.75−5)=462.391176 kN mM(6.75)=267.976471(6.75)-0.8(6.75^2)-200(6.75-3)-320(6.75-5)=462.391176\,\mathrm{kN\,m}
M(7.625)=267.976471(7.625)−0.8(7.6252)−200(7.625−3)−320(7.625−5)=231.808088 kN mM(7.625)=267.976471(7.625)-0.8(7.625^2)-200(7.625-3)-320(7.625-5)=231.808088\,\mathrm{kN\,m}
Source: LectureNotes/Ch3_Beam.pdf · p.16

Use the moments at one-quarter, one-half and three-quarters of THIS restrained segment.

They are not necessarily at load points.

Evaluate the actual quadratic bending diagram including the UDL.

Use absolute magnitudes in the quarter-point expression and compare with the maximum absolute moment in the segment.

Quarter point coordinateMoment (kN·m)
x=5.875 mx=5.875\,\mathrm{m}M=691.749265 kN mM=691.749265\,\mathrm{kN\,m}
x=6.75 mx=6.75\,\mathrm{m}M=462.391176 kN mM=462.391176\,\mathrm{kN\,m}
x=7.625 mx=7.625\,\mathrm{m}M=231.808088 kN mM=231.808088\,\mathrm{kN\,m}
mLT=max⁡(0.44, 0.2+0.15∣M2∣+0.5∣M3∣+0.15∣M4∣∣Mmax∣)m_{LT}=\max\left(0.44,\ 0.2+\frac{0.15|M_2|+0.5|M_3|+0.15|M_4|}{|M_{max}|}\right)
mLT=max⁡(0.44, 0.2+0.15∣691.749265∣+0.5∣462.391176∣+0.15∣231.808088∣919.882353)m_{LT}=\max\left(0.44,\ 0.2+\frac{0.15|691.749265|+0.5|462.391176|+0.15|231.808088|}{919.882353}\right)
mLT=0.601931m_{LT}=0.601931

Use millimetres in slenderness.

The section table supplies the minor-axis radius of gyration, buckling parameter and torsional index.

The given Class 1 section has a plastic-section factor of one.

These quantities change when the section changes.

LE=3500  mm,ry=46  mm,u=0.875,x=30.9,βW=1L_E=3500\;\mathrm{mm},\quad r_y=46\;\mathrm{mm},\quad u=0.875,\quad x=30.9,\quad\beta_W=1
λ=LEry=350046=76.086957\lambda=\frac{L_E}{r_y}=\frac{3500}{46}=76.086957
v=[1+0.05(λx)2]−1/4=[1+0.05(76.08695730.9)2]−1/4=0.935945v=\left[1+0.05\left(\frac{\lambda}{x}\right)^2\right]^{-1/4}=\left[1+0.05\left(\frac{76.086957}{30.9}\right)^2\right]^{-1/4}=0.935945
λLT=uvλβW=0.875×0.935945×76.086957=62.311576\lambda_{LT}=uv\lambda\sqrt{\beta_W}=0.875\times0.935945\times76.086957=62.311576
Source: LectureNotes/CON4334-Data File-20260730.pdf · p.5

Choose Data File p.5, Table 8.3, 345 N/mm² column.

Interpolate between the two surrounding slenderness rows in the same design-strength column.

Do not mix columns.

pb=251+62.311576−6065−60(234−251)=243.14064  N/mm2p_b=251+\frac{62.311576-60}{65-60}(234-251)=243.14064\;\mathrm{N/mm^2}

Buckling strength times plastic modulus gives moment resistance.

Convert the tabulated cubic centimetres to cubic millimetres, then newton-millimetres to kilonewton-metres.

Mb=pbSx×103106=243.14064×28281000=687.60173  kN mM_b=\frac{p_b S_x\times10^3}{10^6}=\frac{243.14064\times2828}{1000}=687.60173\;\mathrm{kN\,m}
mLTMmax=0.601931×919.882353=553.705662  kN mm_{LT}M_{max}=0.601931\times919.882353=553.705662\;\mathrm{kN\,m}
mLTMmaxMb=553.705662687.60173=0.805271≤1\frac{m_{LT}M_{max}}{M_b}=\frac{553.705662}{687.60173}=0.805271\le1

The stated effective-length model passes this LTB check.

Result and concise exam wording

Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Apply the reasoning to this section’s data and conditions

Concise exam wording

RA=267.976, RD=265.624[kN];MB=796.729, MC=919.882[kN m]R_A=267.976,\ R_D=265.624\quad[\mathrm{kN}];\quad M_B=796.729,\ M_C=919.882\quad[\mathrm{kN\,m}]
BC: 871.201<920.603;CD: 553.706<687.602[kN m]BC:\ 871.201<920.603;\quad CD:\ 553.706<687.602\quad[\mathrm{kN\,m}]

Both segments pass the stated normal-loading/effective-length branch; provide SFD/BMD and restraint qualification.

Misconceptions and checks

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

  • B and C lateral restraints are not extra vertical supports.
  • Quarter points belong to each segment, not the entire 8.5 m beam.
  • Do not replace the curved CD moment diagram with an exact straight triangle.

Procedure for a new variant

Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Use the same mechanism: Balance the isolated beam. Move the same load toward B. Reaction B increases because the load has a larger moment arm about A.

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Apply the reasoning to this section’s data and conditions

  1. Find vertical reactions and the full SFD/BMD.
  2. Identify actual restraints and effective lengths.
  3. Evaluate segment quarter moments, mLT, slenderness and table strength.

Prediction with explained answer — invented variant

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Use the same mechanism: A cut reveals the internal actions. Under a uniform downward load, shear falls steadily. Moment reaches a stationary value where shear becomes zero.

Apply the reasoning to this section’s data and conditions

Invented variant: add a lateral restraint halfway through CD without changing vertical supports.

Do reactions change?

Hint

Separate vertical statics from lateral buckling.

Answer and reasoning

No. Vertical reactions and the existing bending diagram stay the same.

Split CD into two LTB segments, choose the new effective lengths and recompute each segment’s quarter-point factor and resistance.