Steelwork · Exam learning

2014–2019 · Reference answers

2016-01-08 — beam answers

All answers shown

All independent beam subquestions, including the required sketches and restraint variants.

Independent teaching answer, not an official solution or marking scheme.

Printed marks are retained.

Read the source conditions beside each result.

Read the diagram and choose the checks

A safe beam can still sag too far

Check whether the beam displacement exceeds the permitted service limit.

The straight beam marks the unloaded position. The curved line and vertical arrow show downward displacement, exaggerated for explanation.
The straight beam marks the unloaded position. The curved line and vertical arrow show downward displacement, exaggerated for explanation.

Prediction, then explanation. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.

Load bends each beam segment. The curvature accumulates along the span. Material stiffness E and geometric stiffness I resist that deformation.

δmid=5wL4384EI\delta_{mid}=\frac{5wL^4}{384EI}

Use w in N/mm, L in mm, E in N/mm² and I in mm⁴. The resulting midspan deflection is in mm.

Scope. The formula assumes a prismatic, simply supported, linear-elastic beam with full-span UDL. Use the stated service load and deflection limit.

Check and takeaway. A higher yield grade does not automatically increase E. Passing a strength check therefore does not prove acceptable deflection.

Keep load categories separate

A floor carries permanent material and changing occupancy loads. Find the design load for the stated check.

The two boxes show G and Q with their separate factors. The plus sign joins their factored values.
The two boxes show G and Q with their separate factors. The plus sign joins their factored values.

Prediction, then explanation. Increasing imposed load changes its own term. It does not change the dead-load factor or the steel stiffness.

First convert mass to weight where required. Next collect G and Q in compatible units. Apply the combination specified by the course problem.

Wu=1.4G+1.6QW_u=1.4G+1.6Q

G is characteristic dead load; Q is characteristic imposed load. Wu is the design load for this course gravity combination.

Scope. This combination is not universal. Use the specified service load for deflection and the stated factors for other standards or cases.

Check and takeaway. Illustration: G = 10 kN and Q = 5 kN give 22 kN. Factoring their sum by one guessed factor loses the distinction.

Change the ruler, keep the quantity

A section table uses centimetres, but the strength calculation uses millimetres. The numbers must describe the same section.

Length1 factorArea2 factors3 factorsEach centimetre becomes ten millimetres.
In the diagram, the length, square and cube contain one, two and three length factors. Each factor changes when the ruler changes.

Prediction, then explanation. Would every property increase by ten? No. The exponent determines how many factors of ten are needed.

First identify the physical quantity. Next convert each length factor. Keep force and length conversions separate when converting a moment.

1 cmn=10n mmn,1 kN m=106 N mm1\,\mathrm{cm}^n=10^n\,\mathrm{mm}^n,\qquad 1\,\mathrm{kN\,m}=10^6\,\mathrm{N\,mm}

Here n is the length exponent: 2 for area, 3 for section modulus and 4 for second moment of area.

Scope. Changing units changes neither the load nor the section. A conversion factor cannot repair a formula for the wrong physical quantity.

Check and takeaway. Illustration: 2 cm4=20,000 mm42\,\mathrm{cm}^4=20{,}000\,\mathrm{mm}^4. The fourth power belongs to the unit, not the number 2.

Apply the reasoning to this section’s data and conditions

Units: 1 kN = 1,000 N; 1 m = 1,000 mm; 1 cm³ = 1,000 mm³; 1 cm⁴ = 10,000 mm⁴.

Demand is the load effect.

Resistance is the permitted capacity for the selected failure mode.

Compare matching units.

The member is 457 × 191 × 74 UB, S355, simply supported over 7 m, with compression-flange restraints at its ends.

Read M and V as ultimate design actions; Q is the unfactored imposed load for deflection.

Do not factor a given design moment again.

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.9, p.10

Lookup the exact 457 × 191 × 74 UB row.

Read dimensions first, properties second.

D = overall depth; t = web thickness; T = flange thickness; d = clear web depth.

The designation identifies a section-table row.

Read exact dimensions from that row.

D=457, t=9, T=14.5, d=407.6(mm)D=457,\ t=9,\ T=14.5,\ d=407.6\quad(\mathrm{mm})
b/T=6.57, d/t=45.3, Ix=33320 cm4, Zx=1458 cm3, Sx=1653 cm3b/T=6.57,\ d/t=45.3,\ I_x=33320\,\mathrm{cm^4},\ Z_x=1458\,\mathrm{cm^3},\ S_x=1653\,\mathrm{cm^3}
ry=42 mm,u=0.877,x=33.9r_y=42\,\mathrm{mm},\quad u=0.877,\quad x=33.9

Section classification [2 marks]

Find which plate buckles first

Before using plastic bending resistance, check whether the flange and web can sustain the required stress distribution.

The short waves are local plate buckling. They differ from sideways movement of the whole member.
The short waves are local plate buckling. They differ from sideways movement of the whole member.

Prediction, then explanation. At fixed width, a thinner plate has a larger width-to-thickness ratio. Local buckling then becomes more restrictive.

Calculate the flange and web ratios separately. Compare each with the limits for its stress condition. The worse class governs.

ε=275/py\varepsilon=\sqrt{275/p_y}

py is the design yield strength in N/mm². ε is a dimensionless scale used in the supplied classification limits.

Scope. Pure bending and uniform compression use different web limits. Class 2 allows plastic resistance but not the Class 1 rotation capability.

Check and takeaway. A Class 1 web and Class 2 flange give a Class 2 section. Do not average the class numbers.

Apply the reasoning to this section’s data and conditions

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.1

S355 design strength depends on the actual flange thickness.

Local classification decides whether plastic bending resistance is allowed.

In pure bending the web limit is different from uniform compression.

py=355 N/mm2,ϵ=275/355=0.880141p_y=355\,\mathrm{N/mm^2},\quad\epsilon=\sqrt{275/355}=0.880141
b/T=6.57,9ϵ=7.921,10ϵ=8.801,13ϵ=11.442b/T=6.57,\quad9\epsilon=7.921,\quad10\epsilon=8.801,\quad13\epsilon=11.442
d/t=45.3<80ϵ=70.411⟹Class 1d/t=45.3<80\epsilon=70.411\quad\Longrightarrow\quad\mathrm{Class}\ 1

Compare the flange class with the web class.

Use the more restrictive class.

Class 1 or 2 permits the capped plastic modulus.

Class 3 uses the elastic modulus.

Result and concise exam wording — key result lines

py=355 N/mm2,ϵ=275/355=0.880141p_y=355\,\mathrm{N/mm^2},\quad\epsilon=\sqrt{275/355}=0.880141
b/T=6.57,9ϵ=7.921,10ϵ=8.801,13ϵ=11.442b/T=6.57,\quad9\epsilon=7.921,\quad10\epsilon=8.801,\quad13\epsilon=11.442
d/t=45.3<80ϵ=70.411⟹Class 1d/t=45.3<80\epsilon=70.411\quad\Longrightarrow\quad\mathrm{Class}\ 1

Compare the flange class with the web class.

Use the more restrictive class.

Class 1 or 2 permits the capped plastic modulus.

Class 3 uses the elastic modulus.

Shear and section resistance [4 marks]

The web carries the shear check

Compare the applied shear with the resistance of the prescribed shear area.

At the imaginary cut, opposing arrows resist relative sliding. The rolled-UB calculation below assigns the shear area to the web.
At the imaginary cut, opposing arrows resist relative sliding. The rolled-UB calculation below assigns the shear area to the web.

Prediction, then explanation. At fixed design strength and depth, increasing web thickness increases this shear resistance.

Calculate the prescribed shear area. Multiply by the design shear stress from the course rule. Then compare matching force units.

Av=Dt,Vc=pyAv/3A_v=Dt,\qquad V_c=p_yA_v/\sqrt{3}

D is overall depth; t is web thickness, in mm. Av uses mm². py uses N/mm², giving Vc in N.

Scope. Apply this area definition to the stated rolled section. Check web slenderness separately. The factor 0.6 is the low-shear threshold, not this resistance coefficient.

Check and takeaway. A shear pass alone does not prove bending, deflection or local support-web adequacy.

Internal tension and compression resist moment

Find which section resistance applies before comparing it with the moment demand.

In sagging bending, the upper region compresses and the lower region stretches. Together their forces form a resisting couple.
In sagging bending, the upper region compresses and the lower region stretches. Together their forces form a resisting couple.

Prediction, then explanation. A larger appropriate section modulus raises resistance at fixed strength. Local plate buckling can restrict the usable modulus.

Classify the section first. At low shear, use the elastic expression for Class 3 or the prescribed capped plastic expression for Classes 1 and 2.

Mc=min⁡(pyS,1.2pyZ)for Class 1/2 at low shearM_c=\min(p_yS,1.2p_yZ)\quad\text{for Class 1/2 at low shear}

py uses N/mm². S is plastic modulus and Z is elastic modulus, both in mm³. Mc then uses N·mm.

Scope. This is section resistance, not whole-member LTB resistance. High shear and Class 4 require their appropriate treatment.

Check and takeaway. Selecting the larger of the two capped terms defeats the cap. Use their minimum.

Apply the reasoning to this section’s data and conditions

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.2

The following shear model assigns the shear area to the web.

For a rolled UB use Av = Dt, then the course shear resistance pyAv/√3.

The factor 0.6 defines the low-shear threshold below.

The shear-resistance coefficient remains the one in the displayed formula.

Av=457(9)=4113 mm2A_v=457(9)=4113\,\mathrm{mm^2}
Vc=pyAv3=355(4113)3(1000)=842.997788 kNV_c=\frac{p_yA_v}{\sqrt3}=\frac{355(4113)}{\sqrt3(1000)}=842.997788\,\mathrm{kN}
V=100 kN,V/Vc=0.118624,0.6Vc=505.798673 kNV=100\,\mathrm{kN},\quad V/V_c=0.118624,\quad0.6V_c=505.798673\,\mathrm{kN}

PASS

Mc=min⁡(pySx,1.2pyZx)/1000=min⁡(355(1653),1.2(355)(1458))/1000=586.815 kN mM_c=\min(p_yS_x,1.2p_yZ_x)/1000=\min(355(1653),1.2(355)(1458))/1000=586.815\,\mathrm{kN\,m}
M/Mc=175/586.815=0.29822M/M_c=175/586.815=0.29822

PASS

The maximum shear is below 0.6Vc.

Therefore every section satisfies this low-shear condition.

Result and concise exam wording — key result lines

Av=457(9)=4113 mm2A_v=457(9)=4113\,\mathrm{mm^2}
Vc=pyAv3=355(4113)3(1000)=842.997788 kNV_c=\frac{p_yA_v}{\sqrt3}=\frac{355(4113)}{\sqrt3(1000)}=842.997788\,\mathrm{kN}
V=100 kN,V/Vc=0.118624,0.6Vc=505.798673 kNV=100\,\mathrm{kN},\quad V/V_c=0.118624,\quad0.6V_c=505.798673\,\mathrm{kN}
Mc=min⁡(pySx,1.2pyZx)/1000=min⁡(355(1653),1.2(355)(1458))/1000=586.815 kN mM_c=\min(p_yS_x,1.2p_yZ_x)/1000=\min(355(1653),1.2(355)(1458))/1000=586.815\,\mathrm{kN\,m}
M/Mc=175/586.815=0.29822M/M_c=175/586.815=0.29822

The maximum shear is below 0.6Vc.

Therefore every section satisfies this low-shear condition.

Lateral-torsional buckling [15 marks]

Vertical bending can trigger sideways motion

A beam has enough local bending resistance. Check whether its compression flange can move sideways and twist.

The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.
The dashed straight line is the initial reference. The curved flange lines illustrate the labelled sideways movement and twist.

Prediction, then explanation. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Identify the compressed flange and effective restraints. Calculate the specified slenderness, read buckling strength and compare resistance with the segment demand.

λ=LE/ry,Mb=pbSx  (Class 1/2),mLTMmax≤Mb\lambda=L_E/r_y,\qquad M_b=p_bS_x\;\text{(Class 1/2)},\qquad m_{LT}M_{max}\le M_b

LE and ry use the same length unit. pb uses N/mm²; Sx uses mm³; Mb uses N·mm. mLT is dimensionless.

Scope. Use the specified section class, effective-length branch and loading condition. Load height alone does not prove a destabilizing case.

Check and takeaway. Removing a lateral restraint requires a new segment stability check. The old shorter-segment result cannot establish the longer segment’s adequacy.

Apply the reasoning to this section’s data and conditions

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.3

First locate the quarter, half and three-quarter points of this restraint segment.

Read the moment magnitude at each point.

Divide each magnitude by the largest moment magnitude anywhere in that segment.

The stations belong to the segment, not necessarily to the whole beam.

Apply the lower bound 0.44.

M2=131.25,M3=175,M4=131.25,Mmax=175(kN m)M_2=131.25,\quad M_3=175,\quad M_4=131.25,\quad M_{max}=175\quad(\mathrm{kN\,m})
mLT=max⁡[0.44,0.2+0.15∣131.25∣+0.5∣175∣+0.15∣131.25∣175]=0.925m_{LT}=\max\left[0.44,0.2+\frac{0.15|131.25|+0.5|175|+0.15|131.25|}{175}\right]=0.925

Use the stated normal-loading effective-length branch: LE equals the distance between effective lateral/torsional restraints.

A lateral restraint changes the stability model.

Add a vertical support only if the detail actually provides one.

Class 1/2 gives βW = 1.

λ=LEry=700042=166.666667\lambda=\frac{L_E}{r_y}=\frac{7000}{42}=166.666667
v=[1+0.05(166.66666733.9)2]−1/4=0.8203v=\left[1+0.05\left(\frac{166.666667}{33.9}\right)^2\right]^{-1/4}=0.8203
λLT=uvλ=0.877(0.8203)(166.666667)=119.900517\lambda_{LT}=uv\lambda=0.877(0.8203)(166.666667)=119.900517
Source: LectureNotes/CON4334-Data File-20260730.pdf · p.5

Table 8.3, py = 355 N/mm² column; bracketing λLT rows 115 and 120.

Interpolate in this column only.

pb=111+119.900517−115120−115(104−111)=104.139276 N/mm2p_b=111+\frac{119.900517-115}{120-115}(104-111)=104.139276\,\mathrm{N/mm^2}
Mb=pbSx/1000=104.139276(1653)/1000=172.142223 kN mM_b=p_bS_x/1000=104.139276(1653)/1000=172.142223\,\mathrm{kN\,m}
mLTMmax=0.925(175)=161.875 kN mm_{LT}M_{max}=0.925(175)=161.875\,\mathrm{kN\,m}
ηLT=161.875/172.142223=0.940356\eta_{LT}=161.875/172.142223=0.940356

PASS

Result and concise exam wording — key result lines

λLT=uvλ=0.877(0.8203)(166.666667)=119.900517\lambda_{LT}=uv\lambda=0.877(0.8203)(166.666667)=119.900517
pb=111+119.900517−115120−115(104−111)=104.139276 N/mm2p_b=111+\frac{119.900517-115}{120-115}(104-111)=104.139276\,\mathrm{N/mm^2}
Mb=pbSx/1000=104.139276(1653)/1000=172.142223 kN mM_b=p_bS_x/1000=104.139276(1653)/1000=172.142223\,\mathrm{kN\,m}
mLTMmax=0.925(175)=161.875 kN mm_{LT}M_{max}=0.925(175)=161.875\,\mathrm{kN\,m}
ηLT=161.875/172.142223=0.940356\eta_{LT}=161.875/172.142223=0.940356

PASS

Imposed-load deflection [3 marks]

Use the same mechanism: A safe beam can still sag too far. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.

Apply the reasoning to this section’s data and conditions

Use imposed load only: 9 kN/m over the whole span.

E = 205,000 N/mm².

Convert I from cm⁴ to mm⁴ by multiplying by 10,000.

Use span in mm. 1 kN/m is numerically 1 N/mm.

δ=5qL4384EI=5(9)(7000)4384(205000)(33320)(10000)=4.119216 mm\delta=\frac{5qL^4}{384EI}=\frac{5(9)(7000)^4}{384(205000)(33320)(10000)}=4.119216\,\mathrm{mm}
δlim=L/360=7000/360=19.444444 mm\delta_{lim}=L/360=7000/360=19.444444\,\mathrm{mm}

PASS

Result and concise exam wording — key result lines

δ=5qL4384EI=5(9)(7000)4384(205000)(33320)(10000)=4.119216 mm\delta=\frac{5qL^4}{384EI}=\frac{5(9)(7000)^4}{384(205000)(33320)(10000)}=4.119216\,\mathrm{mm}
δlim=L/360=7000/360=19.444444 mm\delta_{lim}=L/360=7000/360=19.444444\,\mathrm{mm}

PASS

Sketch LTB deformation [4 marks]

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

Teaching sketch: sideways compression-flange movement, twist and a midspan brace to a stable system.

Teaching sketch: sideways compression-flange movement, twist and a midspan brace to a stable system.

Full-size image

LTB couples lateral movement of the compression flange with twisting of the section.

An effective brace restrains that flange and twist through a load path to a stable system.

For a positive-moment simple beam, the top flange is compressed.

A midspan restraint splits the LTB length into two segments.

It does not split the vertical-load beam into two simply supported beams.

Recalculate the moment shape and mLT in each segment.

Result and concise exam wording — key result lines

Teaching sketch: sideways compression-flange movement, twist and a midspan brace to a stable system.

Teaching sketch: sideways compression-flange movement, twist and a midspan brace to a stable system.

Full-size image

LTB couples lateral movement of the compression flange with twisting of the section.

An effective brace restrains that flange and twist through a load path to a stable system.

For a positive-moment simple beam, the top flange is compressed.

A midspan restraint splits the LTB length into two segments.

It does not split the vertical-load beam into two simply supported beams.

Recalculate the moment shape and mLT in each segment.

Sketch a midspan restraint [2 marks]

Moment shape matters within one segment

Represent a nonuniform moment distribution in the applicable member-buckling equation.

The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.
The two diagrams have equal peaks. The left high-moment region is short; the right high-moment region extends across more of the segment.

Prediction, then explanation. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Evaluate moments from the true whole-beam analysis at the required positions. Apply the exact table’s weights, signs and lower bound.

mLT is an LTB factor. mx and my belong to the specified flexural checks. They are not interchangeable.

Scope. Some rules use magnitudes; others require signed ordinates. A factor does not reduce the actual moment used in a local section check.

Check and takeaway. Measure quarter points from the segment start, not automatically from the beam’s left support.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

A table value has conditions

Find a design property without mixing a row, column or standard from a different case.

The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.
The row and column meet at one cell. The table heading supplies the units and the conditions that give the cell meaning.

Prediction, then explanation. A different flange thickness can select a lower design strength even when the steel grade name remains unchanged.

Match the complete section designation. Read the relevant axis and unit. For strength tables, select material, thickness and curve before interpolating.

Given values come from the question. Lookup values come from a named table. Assumed values require an explicit condition.

Scope. A missing row or omitted restraint cannot be recovered from a schematic’s scale. Keep the result conditional when required data are absent.

Check and takeaway. Record the table, row, column and unit beside the substitution. That makes a later check possible.

Apply the reasoning to this section’s data and conditions

Teaching sketch: sideways compression-flange movement, twist and a midspan brace to a stable system.

Teaching sketch: sideways compression-flange movement, twist and a midspan brace to a stable system.

Full-size image

LTB couples lateral movement of the compression flange with twisting of the section.

An effective brace restrains that flange and twist through a load path to a stable system.

For a positive-moment simple beam, the top flange is compressed.

A midspan restraint splits the LTB length into two segments.

It does not split the vertical-load beam into two simply supported beams.

Recalculate the moment shape and mLT in each segment.

Result and concise exam wording — key result lines

Teaching sketch: sideways compression-flange movement, twist and a midspan brace to a stable system.

Teaching sketch: sideways compression-flange movement, twist and a midspan brace to a stable system.

Full-size image

LTB couples lateral movement of the compression flange with twisting of the section.

An effective brace restrains that flange and twist through a load path to a stable system.

For a positive-moment simple beam, the top flange is compressed.

A midspan restraint splits the LTB length into two segments.

It does not split the vertical-load beam into two simply supported beams.

Recalculate the moment shape and mLT in each segment.

Reusable procedure and traps

Use the same mechanism: Moment shape matters within one segment. Two segments can have equal peak moment but different distributions. Their equivalent moment factors can therefore differ.

Use the same mechanism: A safe beam can still sag too far. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

Apply the reasoning to this section’s data and conditions

  1. Separate ultimate resistance from imposed-load serviceability.

    Keep kN/m and mm-based formulas consistent.

  2. Establish the whole-beam reactions first.

    For each restraint segment use its own length, quarter-point moments and maximum moment.

  3. A high Mc does not prove LTB passes.

    Check mLT M ≤ Mb as well as the applicable section resistance.

  4. A smaller unrestrained length normally increases Mb.

    However, its moment factor changes too.

    Recalculate rather than scaling the old ratio.

Explained variant — invented example

Use the same mechanism: A safe beam can still sag too far. For the same UDL and stiffness, doubling span multiplies deflection by sixteen. Doubling I halves deflection.

Use the same mechanism: Vertical bending can trigger sideways motion. Adding a valid lateral restraint shortens a stability segment. It need not change the beam’s vertical reaction or moment diagram.

A force couple carries moment

Separate the force couple used to carry moment from the force used to carry web shear.

The flange forces act in opposite directions. Their separation z gives the lever arm. The web arrow represents shear.
The flange forces act in opposite directions. Their separation z gives the lever arm. The web arrow represents shear.

Prediction, then explanation. For the same moment, a larger lever arm requires a smaller couple force. It does not remove the web shear.

Moment is force multiplied by perpendicular separation. Divide the required moment by the specified separation to obtain each couple force.

F=M/zF=M/z

M is moment in kN·mm; z is the specified force-line separation in mm; F is force in kN.

Scope. Use the lever arm defined by the source model. Do not silently replace it with overall section depth or another geometric distance.

Check and takeaway. Check flange welds for the couple forces and web welds for the stated shear model. Both force paths need a satisfactory detail.

Apply the reasoning to this section’s data and conditions

Invented variant: add a lateral brace at a quarter-span point without changing vertical supports or loads.

Which calculations change?

Hint

Separate the vertical-load model from the lateral-restraint model.

Explained answer

Reactions, SFD, BMD and vertical-load deflection remain unchanged in this ideal restraint model.

Create new LTB segments, then recalculate each LE, quarter-station moments, mLT, λLT, pb and utilisation.

The brace needs a stable load path and cannot be treated as a new vertical support.