Steelwork · Exam learning

2014–2019 · Reference answers

2015-05-12 — floor and foundations

Solve the complete compulsory question, using the original diagram beside the calculation.

Independent teaching answer, not an official solution or marking scheme. Printed marks are retained. Read the source conditions beside each result.

Read the load path first

The slab arrows point across adjacent B1 beams. Each interior B1 collects half the 2.4 m bay on either side: tributary width 2.4 m. Its labelled span is 8 m. The supporting B2 spans 7.2 m between the drawn columns and receives 2 B1 end reaction(s), at one-third and two-thirds of its span.

Beams aligned directly with a column deliver their end reaction to that column, not as an extra midspan load on B2. The B2 point load is already factored; do not factor it again. The slab gives full compression-flange restraint, so this is section resistance rather than an LTB design.

Units: 1 kN = 1,000 N; 1 m = 1,000 mm; 1 cm³ = 1,000 mm³; 1 cm⁴ = 10,000 mm⁴. A demand is the load effect; a resistance is what the member can carry. Compare matching units.

Simple explanation — open only if needed

Think of a tray resting on small bars, then on two larger edge bars. Follow where each bar ends: that determines which reaction goes onto the next bar.

Load intensity [4 marks]

Given slab thickness 150 mm, finishes 1 kN/m², imposed load 2 kN/m². Convert thickness to metres. Permanent area load includes concrete and finishes; beam weight is added later as a line load.

gk=hγc+gfin=0.15(24.5)+1=4.675 kN/m2g_k=h\gamma_c+g_{fin}=0.15(24.5)+1=4.675\,\mathrm{kN/m^2}
qu=1.4gk+1.6qk=1.4(4.675)+1.6(2)=9.745 kN/m2q_u=1.4g_k+1.6q_k=1.4(4.675)+1.6(2)=9.745\,\mathrm{kN/m^2}
Compact exam answer — key result lines
gk=hγc+gfin=0.15(24.5)+1=4.675 kN/m2g_k=h\gamma_c+g_{fin}=0.15(24.5)+1=4.675\,\mathrm{kN/m^2}
qu=1.4gk+1.6qk=1.4(4.675)+1.6(2)=9.745 kN/m2q_u=1.4g_k+1.6q_k=1.4(4.675)+1.6(2)=9.745\,\mathrm{kN/m^2}

Given slab thickness 150 mm, finishes 1 kN/m², imposed load 2 kN/m². Convert thickness to metres. Permanent area load includes concrete and finishes; beam weight is added later as a line load.

Beam actions [8 marks]

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.9, p.10

Lookup the exact 305 × 165 × 40 UB row. Read dimensions first, properties second. D = overall depth; t = web thickness; T = flange thickness; d = clear web depth. The designation is not an exact dimension.

D=303.4, t=6, T=10.2, d=265.2(mm)D=303.4,\ t=6,\ T=10.2,\ d=265.2\quad(\mathrm{mm})
b/T=8.09, d/t=44.2, Ix=8503 cm4, Zx=560 cm3, Sx=623 cm3b/T=8.09,\ d/t=44.2,\ I_x=8503\,\mathrm{cm^4},\ Z_x=560\,\mathrm{cm^3},\ S_x=623\,\mathrm{cm^3}
ry=38.6 mm,u=0.889,x=31r_y=38.6\,\mathrm{mm},\quad u=0.889,\quad x=31
Source: LectureNotes/CON4334-Data File-20260730.pdf · p.9, p.10

Lookup the exact 356 × 171 × 51 UB row. Read dimensions first, properties second. D = overall depth; t = web thickness; T = flange thickness; d = clear web depth. The designation is not an exact dimension.

D=355, t=7.4, T=11.5, d=311.6(mm)D=355,\ t=7.4,\ T=11.5,\ d=311.6\quad(\mathrm{mm})
b/T=7.46, d/t=42.1, Ix=14140 cm4, Zx=796 cm3, Sx=896 cm3b/T=7.46,\ d/t=42.1,\ I_x=14140\,\mathrm{cm^4},\ Z_x=796\,\mathrm{cm^3},\ S_x=896\,\mathrm{cm^3}
ry=38.6 mm,u=0.881,x=32.1r_y=38.6\,\mathrm{mm},\quad u=0.881,\quad x=32.1

Lookup mass in kg/m and multiply by g/1000 to get kN/m. Multiply the slab area load by the tributary width, not by the full slab area.

wg1=40.3(10)/1000=0.403,wg2=51(10)/1000=0.51(kN/m)w_{g1}=40.3(10)/1000=0.403,\quad w_{g2}=51(10)/1000=0.51\quad(\mathrm{kN/m})
wu1=qub+1.4wg1=9.745(2.4)+1.4(0.403)=23.9522 kN/mw_{u1}=q_ub+1.4w_{g1}=9.745(2.4)+1.4(0.403)=23.9522\,\mathrm{kN/m}
V1=R1=wu1L1/2=23.9522(8)/2=95.8088 kNV_1=R_1=w_{u1}L_1/2=23.9522(8)/2=95.8088\,\mathrm{kN}
M1=wu1L12/8=23.9522(82)/8=191.6176 kN mM_1=w_{u1}L_1^2/8=23.9522(8^2)/8=191.6176\,\mathrm{kN\,m}

For B2 use superposition: the B1 point reactions plus B2 self-weight. Equilibrium divides the symmetric total load equally between the supports.

wu2=1.4(0.51)=0.714 kN/m,P=R1=95.8088 kNw_{u2}=1.4(0.51)=0.714\,\mathrm{kN/m},\quad P=R_1=95.8088\,\mathrm{kN}
V2=2P+wu2L22=2(95.8088)+0.714(7.2)2=98.3792 kNV_2=\frac{2P+w_{u2}L_2}{2}=\frac{2(95.8088)+0.714(7.2)}{2}=98.3792\,\mathrm{kN}
M2=PL23+wu2L228=95.8088(7.2)3+0.714(7.22)8=234.56784 kN mM_2=\frac{PL_2}{3}+\frac{w_{u2}L_2^2}{8}=\frac{95.8088(7.2)}{3}+\frac{0.714(7.2^2)}{8}=234.56784\,\mathrm{kN\,m}
Compact exam answer — key result lines
V1=R1=wu1L1/2=23.9522(8)/2=95.8088 kNV_1=R_1=w_{u1}L_1/2=23.9522(8)/2=95.8088\,\mathrm{kN}
M1=wu1L12/8=23.9522(82)/8=191.6176 kN mM_1=w_{u1}L_1^2/8=23.9522(8^2)/8=191.6176\,\mathrm{kN\,m}
wu2=1.4(0.51)=0.714 kN/m,P=R1=95.8088 kNw_{u2}=1.4(0.51)=0.714\,\mathrm{kN/m},\quad P=R_1=95.8088\,\mathrm{kN}
V2=2P+wu2L22=2(95.8088)+0.714(7.2)2=98.3792 kNV_2=\frac{2P+w_{u2}L_2}{2}=\frac{2(95.8088)+0.714(7.2)}{2}=98.3792\,\mathrm{kN}
M2=PL23+wu2L228=95.8088(7.2)3+0.714(7.22)8=234.56784 kN mM_2=\frac{PL_2}{3}+\frac{w_{u2}L_2^2}{8}=\frac{95.8088(7.2)}{3}+\frac{0.714(7.2^2)}{8}=234.56784\,\mathrm{kN\,m}

For B2 use superposition: the B1 point reactions plus B2 self-weight. Equilibrium divides the symmetric total load equally between the supports.

Section classes [4 marks]

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.1

S355 design strength depends on the actual flange thickness. Local classification decides whether plastic bending resistance is allowed. In pure bending the web limit is different from uniform compression.

py=355 N/mm2,ϵ=275/355=0.880141p_y=355\,\mathrm{N/mm^2},\quad\epsilon=\sqrt{275/355}=0.880141
b/T=8.09,9ϵ=7.921,10ϵ=8.801,13ϵ=11.442b/T=8.09,\quad9\epsilon=7.921,\quad10\epsilon=8.801,\quad13\epsilon=11.442
d/t=44.2<80ϵ=70.411⟹Class 2d/t=44.2<80\epsilon=70.411\quad\Longrightarrow\quad\mathrm{Class}\ 2

Take the worse flange/web class. Class 1 or 2 permits the capped plastic modulus; Class 3 uses the elastic modulus.

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.1

S355 design strength depends on the actual flange thickness. Local classification decides whether plastic bending resistance is allowed. In pure bending the web limit is different from uniform compression.

py=355 N/mm2,ϵ=275/355=0.880141p_y=355\,\mathrm{N/mm^2},\quad\epsilon=\sqrt{275/355}=0.880141
b/T=7.46,9ϵ=7.921,10ϵ=8.801,13ϵ=11.442b/T=7.46,\quad9\epsilon=7.921,\quad10\epsilon=8.801,\quad13\epsilon=11.442
d/t=42.1<80ϵ=70.411⟹Class 1d/t=42.1<80\epsilon=70.411\quad\Longrightarrow\quad\mathrm{Class}\ 1

Take the worse flange/web class. Class 1 or 2 permits the capped plastic modulus; Class 3 uses the elastic modulus.

Compact exam answer — key result lines
b/T=8.09,9ϵ=7.921,10ϵ=8.801,13ϵ=11.442b/T=8.09,\quad9\epsilon=7.921,\quad10\epsilon=8.801,\quad13\epsilon=11.442
d/t=44.2<80ϵ=70.411⟹Class 2d/t=44.2<80\epsilon=70.411\quad\Longrightarrow\quad\mathrm{Class}\ 2
py=355 N/mm2,ϵ=275/355=0.880141p_y=355\,\mathrm{N/mm^2},\quad\epsilon=\sqrt{275/355}=0.880141
b/T=7.46,9ϵ=7.921,10ϵ=8.801,13ϵ=11.442b/T=7.46,\quad9\epsilon=7.921,\quad10\epsilon=8.801,\quad13\epsilon=11.442
d/t=42.1<80ϵ=70.411⟹Class 1d/t=42.1<80\epsilon=70.411\quad\Longrightarrow\quad\mathrm{Class}\ 1

Take the worse flange/web class. Class 1 or 2 permits the capped plastic modulus; Class 3 uses the elastic modulus.

B1 checks [10 marks]

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.2

The web carries shear. For a rolled UB use Av = Dt, then the course shear resistance pyAv/√3. The 0.6 factor below is the low-shear threshold; it is not the coefficient in the shear-resistance formula.

Av=303.4(6)=1820.4 mm2A_v=303.4(6)=1820.4\,\mathrm{mm^2}
Vc=pyAv3=355(1820.4)3(1000)=373.107993 kNV_c=\frac{p_yA_v}{\sqrt3}=\frac{355(1820.4)}{\sqrt3(1000)}=373.107993\,\mathrm{kN}
V=95.8088 kN,V/Vc=0.256786,0.6Vc=223.864796 kNV=95.8088\,\mathrm{kN},\quad V/V_c=0.256786,\quad0.6V_c=223.864796\,\mathrm{kN}

PASS

Mc=min⁡(pySx,1.2pyZx)/1000=min⁡(355(623),1.2(355)(560))/1000=221.165 kN mM_c=\min(p_yS_x,1.2p_yZ_x)/1000=\min(355(623),1.2(355)(560))/1000=221.165\,\mathrm{kN\,m}
M/Mc=191.6176/221.165=0.866401M/M_c=191.6176/221.165=0.866401

PASS

Even the maximum shear is below 0.6Vc, so the low-shear moment resistance applies throughout.

For serviceability use unfactored imposed load only, E = 205,000 N/mm², I in mm⁴ and span in mm. Do not include the ULS factors or dead load in this course deflection limit.

δ1=5wQL14384EI1=5(2(2.4))(8000)4384(205000)(8503×104)=14.686352 mm\delta_1=\frac{5w_QL_1^4}{384EI_1}=\frac{5(2(2.4))(8000)^4}{384(205000)(8503\times10^4)}=14.686352\,\mathrm{mm}
δlim=L/360=8000/360=22.222222 mm\delta_{lim}=L/360=8000/360=22.222222\,\mathrm{mm}

PASS

Compact exam answer — key result lines
V=95.8088 kN,V/Vc=0.256786,0.6Vc=223.864796 kNV=95.8088\,\mathrm{kN},\quad V/V_c=0.256786,\quad0.6V_c=223.864796\,\mathrm{kN}
Mc=min⁡(pySx,1.2pyZx)/1000=min⁡(355(623),1.2(355)(560))/1000=221.165 kN mM_c=\min(p_yS_x,1.2p_yZ_x)/1000=\min(355(623),1.2(355)(560))/1000=221.165\,\mathrm{kN\,m}
M/Mc=191.6176/221.165=0.866401M/M_c=191.6176/221.165=0.866401
δ1=5wQL14384EI1=5(2(2.4))(8000)4384(205000)(8503×104)=14.686352 mm\delta_1=\frac{5w_QL_1^4}{384EI_1}=\frac{5(2(2.4))(8000)^4}{384(205000)(8503\times10^4)}=14.686352\,\mathrm{mm}
δlim=L/360=8000/360=22.222222 mm\delta_{lim}=L/360=8000/360=22.222222\,\mathrm{mm}

PASS

B2 checks [10 marks]

Source: LectureNotes/CON4334-Data File-20260730.pdf · p.2

The web carries shear. For a rolled UB use Av = Dt, then the course shear resistance pyAv/√3. The 0.6 factor below is the low-shear threshold; it is not the coefficient in the shear-resistance formula.

Av=355(7.4)=2627 mm2A_v=355(7.4)=2627\,\mathrm{mm^2}
Vc=pyAv3=355(2627)3(1000)=538.428201 kNV_c=\frac{p_yA_v}{\sqrt3}=\frac{355(2627)}{\sqrt3(1000)}=538.428201\,\mathrm{kN}
V=98.3792 kN,V/Vc=0.182716,0.6Vc=323.05692 kNV=98.3792\,\mathrm{kN},\quad V/V_c=0.182716,\quad0.6V_c=323.05692\,\mathrm{kN}

PASS

Mc=min⁡(pySx,1.2pyZx)/1000=min⁡(355(896),1.2(355)(796))/1000=318.08 kN mM_c=\min(p_yS_x,1.2p_yZ_x)/1000=\min(355(896),1.2(355)(796))/1000=318.08\,\mathrm{kN\,m}
M/Mc=234.56784/318.08=0.737449M/M_c=234.56784/318.08=0.737449

PASS

Even the maximum shear is below 0.6Vc, so the low-shear moment resistance applies throughout.

For serviceability use unfactored imposed load only, E = 205,000 N/mm², I in mm⁴ and span in mm. Do not include the ULS factors or dead load in this course deflection limit.

PQ=qkbL1/2=2(2.4)(8)/2=19.2 kNP_Q=q_kbL_1/2=2(2.4)(8)/2=19.2\,\mathrm{kN}
δ2=23PQL23648EI2=23(19.2)(1000)(7200)3648(205000)(14140×104)=8.775023 mm\delta_2=\frac{23P_QL_2^3}{648EI_2}=\frac{23(19.2)(1000)(7200)^3}{648(205000)(14140\times10^4)}=8.775023\,\mathrm{mm}

Here P is each of the two equal third-point loads, not their sum. Setting a/L = 1/3 in the symmetric two-load formula gives 23/648.

δlim=L/360=7200/360=20 mm\delta_{lim}=L/360=7200/360=20\,\mathrm{mm}

PASS

Compact exam answer — key result lines
Mc=min⁡(pySx,1.2pyZx)/1000=min⁡(355(896),1.2(355)(796))/1000=318.08 kN mM_c=\min(p_yS_x,1.2p_yZ_x)/1000=\min(355(896),1.2(355)(796))/1000=318.08\,\mathrm{kN\,m}
M/Mc=234.56784/318.08=0.737449M/M_c=234.56784/318.08=0.737449
PQ=qkbL1/2=2(2.4)(8)/2=19.2 kNP_Q=q_kbL_1/2=2(2.4)(8)/2=19.2\,\mathrm{kN}
δ2=23PQL23648EI2=23(19.2)(1000)(7200)3648(205000)(14140×104)=8.775023 mm\delta_2=\frac{23P_QL_2^3}{648EI_2}=\frac{23(19.2)(1000)(7200)^3}{648(205000)(14140\times10^4)}=8.775023\,\mathrm{mm}
δlim=L/360=7200/360=20 mm\delta_{lim}=L/360=7200/360=20\,\mathrm{mm}

PASS

Short theory: limit-states [4 marks]

  • ULS — strength: shear yielding, bending failure or connection failure can prevent the structure carrying the design load.
  • ULS — stability: member buckling or overall loss of equilibrium can cause collapse.
  • SLS — deflection: excessive movement can damage finishes or stop doors/services working even before collapse.
  • SLS — vibration: excessive response causes discomfort or interferes with use.

Give two examples from each category; ULS concerns load-carrying safety, SLS concerns acceptable use.

Compact exam answer — key result lines
  • ULS — strength: shear yielding, bending failure or connection failure can prevent the structure carrying the design load.
  • ULS — stability: member buckling or overall loss of equilibrium can cause collapse.
  • SLS — deflection: excessive movement can damage finishes or stop doors/services working even before collapse.
  • SLS — vibration: excessive response causes discomfort or interferes with use.

Give two examples from each category; ULS concerns load-carrying safety, SLS concerns acceptable use.

Reusable exam procedure and mistakes

  1. Trace the slab arrows and count reactions before doing arithmetic.
  2. Use each member’s exact table row. Class 2 is not Class 1, but both allow capped plastic bending.
  3. Never factor an already factored reaction twice; never include beam dead weight in imposed-load deflection.

Independent practice — invented variant

Invented variant: imposed load rises by 20%, with dead load unchanged. What changes?

Hint

Separate permanent and imposed terms before changing a load.

Reveal answer

Multiply imposed-only deflections by 1.2. Rebuild ULS load as 1.4G + 1.6(1.2Q); do not multiply the total ULS action by 1.2. Section capacities and classes stay unchanged.