All independent beam subquestions, including the required sketches and restraint variants.
Independent teaching answer, not an official solution or marking scheme. Printed marks are retained. Read the source conditions beside each result.
Read the diagram and choose the checks
Units: 1 kN = 1,000 N; 1 m = 1,000 mm; 1 cm³ = 1,000 mm³; 1 cm⁴ = 10,000 mm⁴. A demand is the load effect; a resistance is what the member can carry. Compare matching units.
The member is 457 × 152 × 52 UB, S355, simply supported over 6 m, with compression-flange restraints at its ends. Read M and V as ultimate design actions; Q is the unfactored imposed load for deflection. Do not factor a given design moment again.
Lookup the exact 457 × 152 × 52 UB row. Read dimensions first, properties second. D = overall depth; t = web thickness; T = flange thickness; d = clear web depth. The designation is not an exact dimension.
S355 design strength depends on the actual flange thickness. Local classification decides whether plastic bending resistance is allowed. In pure bending the web limit is different from uniform compression.
py=355N/mm2,ϵ=275/355=0.880141
b/T=6.99,9ϵ=7.921,10ϵ=8.801,13ϵ=11.442
d/t=53.6<80ϵ=70.411⟹Class1
Take the worse flange/web class. Class 1 or 2 permits the capped plastic modulus; Class 3 uses the elastic modulus.
Compact exam answer — key result lines
py=355N/mm2,ϵ=275/355=0.880141
b/T=6.99,9ϵ=7.921,10ϵ=8.801,13ϵ=11.442
d/t=53.6<80ϵ=70.411⟹Class1
Take the worse flange/web class. Class 1 or 2 permits the capped plastic modulus; Class 3 uses the elastic modulus.
The web carries shear. For a rolled UB use Av = Dt, then the course shear resistance pyAv/√3. The 0.6 factor below is the low-shear threshold; it is not the coefficient in the shear-resistance formula.
For this restraint segment, take the absolute moments at its quarter, half and three-quarter points; divide by the largest absolute moment anywhere in the same segment. The stations belong to the segment, not necessarily to the whole beam. Apply the lower bound 0.44.
Use the stated normal-loading effective-length branch: LE equals the distance between effective lateral/torsional restraints. A restraint does not create a new vertical support. Class 1/2 gives βW = 1.
Use imposed load only: 5 kN/m over the whole span. E = 205,000 N/mm². Convert I from cm⁴ to mm⁴ by multiplying by 10,000; use span in mm. 1 kN/m is numerically 1 N/mm.
Separate ultimate resistance from imposed-load serviceability. Keep kN/m and mm-based formulas consistent.
Establish the whole-beam reactions first. For each restraint segment use its own length, quarter-point moments and maximum moment.
A high Mc does not prove LTB passes. Check mLT M ≤ Mb as well as the applicable section resistance.
A smaller unrestrained length normally increases Mb, but its moment factor changes too; recalculate rather than scaling the old ratio.
Independent practice — invented variant
Invented variant: add a lateral brace at a quarter-span point without changing vertical supports or loads. Which calculations change?
Hint
Separate the vertical-load model from the lateral-restraint model.
Reveal answer
Reactions, SFD, BMD and vertical-load deflection remain unchanged in this ideal restraint model. Create new LTB segments, then recalculate each LE, quarter-station moments, mLT, λLT, pb and utilisation. The brace needs a stable load path and cannot be treated as a new vertical support.